3M B1768532, B1768656, B1768504, B1768378, B1768374 User Manual

3M™ Abrasive Products, 340D P40-P120 06/03/14

__________________________________________________________________________________________

Page 1 of 10

Safety Data Sheet

Copyright,2014,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.

Document Group:

26-8233-4

Version Number:

1.08

Issue Date:

06/03/14

Supercedes Date:

03/25/14

SECTION 1: Identification

1.1. Product identifier

3M™ Abrasive Products, 340D P40-P120

1.2. Recommended use and restrictions on use

Recommended use

Abrasive Product

1.3. Supplier’s details
MANUFACTURER:

3M

DIVISION:

Abrasive Systems Division

ADDRESS:

3M Center, St. Paul, MN 55144-1000, USA

Telephone:

1-888-3M HELPS (1-888-364-3577)

1.4. Emergency telephone number

1-800-364-3577 or [phone] (24 hours)

SECTION 2: Hazard identification

2.1. Hazard classification

Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200.

2.2. Label elements

Signal word

Not applicable.

Symbols

Not applicable.

Pictograms

Not applicable.

2.3. Hazards not otherwise classified

None.

50% of the mixture consists of ingredients of unknown acute oral toxicity.

3M™ Abrasive Products, 340D P40-P120 06/03/14

__________________________________________________________________________________________

Page 2 of 10

SECTION 3: Composition/information on ingredients

Ingredient C.A.S. No. % by Wt

Aluminum Oxide Mineral (non-fibrous) 1344-28-1 15 - 30
Filler 1317-65-3 10 - 25
Filler 471-34-1 0.5 - 5
Filler 1332-58-7 1 - 5
Titanium Dioxide 13463-67-7 0.1 - 2
Quartz Silica 14808-60-7 0.01 - 0.35
Cured Resin Mixture 10 - 30
Cloth Backing Mixture 20 - 50

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation:

Remove person to fresh air. If you feel unwell, get medical attention.

Skin Contact:

Wash with soap and water. If signs/symptoms develop, get medical attention.

Eye Contact:

Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get
medical attention.

If Swallowed:

No need for first aid is anticipated.

4.2. Most important symptoms and effects, both acute and delayed

See Section 11.1. Information on toxicological effects.

4.3. Indication of any immediate medical attention and special treatment required

Not applicable

SECTION 5: Fire-fighting measures

5.1. Suitable extinguishing media

In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.

5.2. Special hazards arising from the substance or mixture

None inherent in this product.

Hazardous Decomposition or By-Products

Substance Condition

Carbon monoxide During Combustion
Carbon dioxide During Combustion

5.3. Special protective actions for fire-fighters

No unusual fire or explosion hazards are anticipated.

SECTION 6: Accidental release measures

3M™ Abrasive Products, 340D P40-P120 06/03/14

__________________________________________________________________________________________

Page 3 of 10

6.1. Personal precautions, protective equipment and emergency procedures

Observe precautions from other sections.

6.2. Environmental precautions

Not applicable.

6.3. Methods and material for containment and cleaning up

Not applicable.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

For industrial or professional use only. Damaged product can break apart during use and cause serious injury to face or eyes.
Check product for damage such as cracks or nicks prior to use. Replace if damaged. Always wear eye and face protection
when working at sanding or grinding operations or when near such operations. Combustible dust may form by action of this
product on another material (substrate). Dust generated from the substrate during use of this product may be explosive if in
sufficient concentration with an ignition source. Dust deposits should not be allowed to accumulate on surfaces because of
the potential for secondary explosions.

7.2. Conditions for safe storage including any incompatibilities

No special storage requirements.

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

Occupational exposure limits

Ingredient C.A.S. No. Agency Limit type Additional Comments

Filler 1317-65-3 OSHA TWA(as total dust):15

mg/m3;TWA(respirable
fraction):5 mg/m3

Filler 1332-58-7 ACGIH TWA(respirable fraction):2

mg/m3

KAOLIN, TOTAL DUST 1332-58-7 OSHA TWA(as total dust):15

mg/m3;TWA(respirable

fraction):5 mg/m3
Aluminum Oxide Mineral (non­fibrous)

1344-28-1 CMRG TWA:1 fiber/cc

Aluminum Oxide Mineral (non­fibrous)

1344-28-1 OSHA TWA(as total dust):15

mg/m3;TWA(respirable

fraction):5 mg/m3
Aluminum, insoluble compounds 1344-28-1 ACGIH TWA(respirable fraction):1

mg/m3
Titanium Dioxide 13463-67-7 ACGIH TWA:10 mg/m3
Titanium Dioxide 13463-67-7 CMRG TWA(as respirable dust):5

mg/m3
Titanium Dioxide 13463-67-7 OSHA TWA(as total dust):15 mg/m3
Quartz Silica 14808-60-7 ACGIH TWA(respirable

fraction):0.025 mg/m3
Quartz Silica 14808-60-7 OSHA TWA concentration(as total

dust):0.3 mg/m3;TWA

concentration(respirable):0.1