3M™ Abrasive Products, 577F Grades 120-180 04/07/14
Safety Data Sheet
Copyright,2014,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
Document Group: |
26-2082-1 |
Version Number: |
2.09 |
Issue Date: |
04/07/14 |
Supercedes Date: |
05/28/13 |
SECTION 1: Identification
1.1. Product identifier
3M™ Abrasive Products, 577F Grades 120-180
1.2. Recommended use and restrictions on use
Recommended use
Abrasive Product
1.3. Supplier’s details |
3M |
MANUFACTURER: |
|
DIVISION: |
Abrasive Systems Division |
ADDRESS: |
3M Center, St. Paul, MN 55144-1000, USA |
Telephone: |
1-888-3M HELPS (1-888-364-3577) |
1.4. Emergency telephone number
1-800-364-3577 or (651) 737-6501 (24 hours)
SECTION 2: Hazard identification
2.1. Hazard classification
Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200.
2.2. Label elements Signal word
Not applicable.
Symbols
Not applicable.
Pictograms
Not applicable.
2.3. Hazards not otherwise classified
None.
46% of the mixture consists of ingredients of unknown acute oral toxicity.
__________________________________________________________________________________________
Page 1 of 10
3M™ Abrasive Products, 577F Grades 120-180 04/07/14
SECTION 3: Composition/information on ingredients
Ingredient |
C.A.S. No. |
% by Wt |
||
Zirconium Oxide Mineral |
1314-23-4 |
3 |
- 15 |
|
Aluminum Oxide Mineral (non-fibrous) |
1344-28-1 |
5 |
- 30 |
|
Limestone |
1317-65-3 |
2 |
- 15 |
|
Inorganic Fluoride |
14075-53-7 |
2 |
- |
10 |
Inorganic Fluoride |
15096-52-3 |
2 |
- |
10 |
Titanium Dioxide |
13463-67-7 |
0.25 - 2 |
||
Carbon Black |
1333-86-4 |
0.01 - 0.15 |
||
Quartz Silica |
14808-60-7 |
0 |
- |
0.12 |
Cured Resin |
Mixture |
10 - 35 |
||
Cloth Backing |
Mixture |
20 - 50 |
SECTION 4: First aid measures
4.1. Description of first aid measures
Inhalation:
Remove person to fresh air. If you feel unwell, get medical attention.
Skin Contact:
Wash with soap and water. If signs/symptoms develop, get medical attention.
Eye Contact:
Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get medical attention.
If Swallowed:
No need for first aid is anticipated.
4.2.Most important symptoms and effects, both acute and delayed
See Section 11.1. Information on toxicological effects.
4.3.Indication of any immediate medical attention and special treatment required
Not applicable
SECTION 5: Fire-fighting measures
5.1. Suitable extinguishing media
In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.
5.2.Special hazards arising from the substance or mixture
None inherent in this product.
5.3.Special protective actions for fire-fighters
No unusual fire or explosion hazards are anticipated.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Observe precautions from other sections.
__________________________________________________________________________________________
Page 2 of 10
3M™ Abrasive Products, 577F Grades 120-180 04/07/14
6.2.Environmental precautions
Avoid release to the environment.
6.3.Methods and material for containment and cleaning up
Not applicable.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
For industrial or professional use only. Avoid breathing of dust created by sanding, grinding or machining. Damaged product can break apart during use and cause serious injury to face or eyes. Check product for damage such as cracks or nicks prior to use. Replace if damaged. Always wear eye and face protection when working at sanding or grinding operations or when near such operations. Avoid release to the environment. Combustible dust may form by action of this product on another material (substrate). Dust generated from the substrate during use of this product may be explosive if in sufficient concentration with an ignition source. Dust deposits should not be allowed to accumulate on surfaces because of the potential for secondary explosions.
7.2. Conditions for safe storage including any incompatibilities
No special storage requirements.
SECTION 8: Exposure controls/personal protection
8.1. Control parameters Occupational exposure limits
Ingredient |
C.A.S. No. |
Agency |
Limit type |
Additional Comments |
ZIRCONIUM COMPOUNDS |
1314-23-4 |
Amer Conf of |
TWA(as Zr):5 |
|
|
|
Gov. Indust. |
mg/m3;STEL(as Zr):10 mg/m3 |
|
|
|
Hyg. |
|
|
ZIRCONIUM COMPOUNDS |
1314-23-4 |
US Dept of |
TWA(as Zr):5 mg/m3 |
|
|
|
Labor - OSHA |
|
|
Limestone |
1317-65-3 |
US Dept of |
TWA(as total dust):15 |
|
|
|
Labor - OSHA |
mg/m3;TWA(respirable |
|
|
|
|
fraction):5 mg/m3 |
|
Carbon Black |
1333-86-4 |
Amer Conf of |
TWA(inhalable fraction):3 |
|
|
|
Gov. Indust. |
mg/m3 |
|
|
|
Hyg. |
|
|
Carbon Black |
1333-86-4 |
Chemical |
TWA:0.5 mg/m3 |
|
|
|
Manufacturer |
|
|
|
|
Rec Guid |
|
|
Carbon Black |
1333-86-4 |
US Dept of |
TWA:3.5 mg/m3 |
|
|
|
Labor - OSHA |
|
|
Aluminum Oxide Mineral (non- |
1344-28-1 |
Chemical |
TWA:1 fiber/cc |
|
fibrous) |
|
Manufacturer |
|
|
|
|
Rec Guid |
|
|
Aluminum Oxide Mineral (non- |
1344-28-1 |
US Dept of |
TWA(as total dust):15 |
|
fibrous) |
|
Labor - OSHA |
mg/m3;TWA(respirable |
|
|
|
|
fraction):5 mg/m3 |
|
Aluminum, insoluble compounds |
1344-28-1 |
Amer Conf of |
TWA(respirable fraction):1 |
|
|
|
Gov. Indust. |
mg/m3 |
|
|
|
Hyg. |
|
|
Titanium Dioxide |
13463-67-7 |
Amer Conf of |
TWA:10 mg/m3 |
|
|
|
Gov. Indust. |
|
|
__________________________________________________________________________________________
Page 3 of 10