3M 60440273377, 60440273567, 60440273427, 60440273609, 60440273419 User Manual

3M™ Abrasive Products, Cubitron™ II 967A Flap Discs 06/27/14

__________________________________________________________________________________________

Page 1 of 10

Safety Data Sheet

Copyright,2014,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.

Document Group:

31-7032-1

Version Number:

1.05

Issue Date:

06/27/14

Supercedes Date:

02/17/14

SECTION 1: Identification

1.1. Product identifier

3M™ Abrasive Products, Cubitron™ II 967A Flap Discs

1.2. Recommended use and restrictions on use

Recommended use

Abrasive Product

1.3. Supplier’s details
MANUFACTURER:

3M

DIVISION:

Abrasive Systems Division

ADDRESS:

3M Center, St. Paul, MN 55144-1000, USA

Telephone:

1-888-3M HELPS (1-888-364-3577)

1.4. Emergency telephone number

1-800-364-3577 or [phone] (24 hours)

SECTION 2: Hazard identification

2.1. Hazard classification

Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200.

2.2. Label elements

Signal word

Not applicable.

Symbols

Not applicable.

Pictograms

Not applicable.

2.3. Hazards not otherwise classified

None.

46% of the mixture consists of ingredients of unknown acute oral toxicity.

SECTION 3: Composition/information on ingredients

3M™ Abrasive Products, Cubitron™ II 967A Flap Discs 06/27/14

__________________________________________________________________________________________

Page 2 of 10

Ingredient C.A.S. No. % by Wt

Ceramic Aluminum Oxide (non-fibrous) 1344-28-1 5 - 20
Inorganic Fluoride 14075-53-7 2 - 15
Inorganic Fluoride 15096-52-3 1 - 10
Filler 13983-17-0 2 - 15
Filler 7727-43-7 1 - 5
Titanium Dioxide 13463-67-7 0 - 0.8
Cured Resin Mixture 10 - 35
Cloth Backing Mixture 15 - 30
Fiberglass plate Mixture 20 - 30

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation:

Remove person to fresh air. If you feel unwell, get medical attention.

Skin Contact:

Wash with soap and water. If signs/symptoms develop, get medical attention.

Eye Contact:

Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get
medical attention.

If Swallowed:

No need for first aid is anticipated.

4.2. Most important symptoms and effects, both acute and delayed

See Section 11.1. Information on toxicological effects.

4.3. Indication of any immediate medical attention and special treatment required

Not applicable.

SECTION 5: Fire-fighting measures

5.1. Suitable extinguishing media

In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.

5.2. Special hazards arising from the substance or mixture

None inherent in this product.

Hazardous Decomposition or By-Products

Substance Condition

Carbon monoxide During Combustion
Carbon dioxide During Combustion
Hydrogen Fluoride During Combustion

5.3. Special protective actions for fire-fighters

When fire fighting conditions are severe and total thermal decomposition of the product is possible, wear full protective
clothing, including helmet, self-contained, positive pressure or pressure demand breathing apparatus, bunker coat and pants,
bands around arms, waist and legs, face mask, and protective covering for exposed areas of the head.

3M™ Abrasive Products, Cubitron™ II 967A Flap Discs 06/27/14

__________________________________________________________________________________________

Page 3 of 10

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Observe precautions from other sections.

6.2. Environmental precautions

Not applicable.

6.3. Methods and material for containment and cleaning up

Not applicable.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

Do not breathe thermal decomposition products. Avoid breathing of dust created by sanding, grinding or machining.
Damaged product can break apart during use and cause serious injury to face or eyes. Check product for damage such as
cracks or nicks prior to use. Replace if damaged. Always wear eye and face protection when working at sanding or grinding
operations or when near such operations. Combustible dust may form by action of this product on another material
(substrate). Dust generated from the substrate during use of this product may be explosive if in sufficient concentration with
an ignition source. Dust deposits should not be allowed to accumulate on surfaces because of the potential for secondary
explosions.

7.2. Conditions for safe storage including any incompatibilities

No special storage requirements.

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

Occupational exposure limits

Ingredient C.A.S. No. Agency Limit type Additional Comments

Aluminum, insoluble compounds 1344-28-1 ACGIH TWA(respirable fraction):1

mg/m3
Ceramic Aluminum Oxide (non­fibrous)

1344-28-1 CMRG TWA:1 fiber/cc

Ceramic Aluminum Oxide (non­fibrous)

1344-28-1 OSHA TWA(as total dust):15

mg/m3;TWA(respirable

fraction):5 mg/m3
Titanium Dioxide 13463-67-7 ACGIH TWA:10 mg/m3
Titanium Dioxide 13463-67-7 CMRG TWA(as respirable dust):5

mg/m3
Titanium Dioxide 13463-67-7 OSHA TWA(as total dust):15 mg/m3
Aluminum, insoluble compounds 15096-52-3 ACGIH TWA(respirable fraction):1

mg/m3
FLUORIDES 15096-52-3 ACGIH TWA(as F):2.5 mg/m3
FLUORIDES 15096-52-3 OSHA TWA(as dust):2.5

mg/m3;TWA(as F):2.5 mg/m3
Filler 7727-43-7 ACGIH TWA(inhalable fraction):5

mg/m3
Filler 7727-43-7 OSHA TWA(as total dust):15

mg/m3;TWA(respirable

fraction):5 mg/m3