3M 60440271421, 60440271520, 60440271173 User Manual

3M™ Abrasive Product, 566A Flap Discs: Types 27, 29 02/17/14

__________________________________________________________________________________________

Page 1 of 10

Safety Data Sheet

Copyright,2014,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.

Document Group:

29-7268-5

Version Number:

1.01

Issue Date:

02/17/14

Supercedes Date:

08/23/11

SECTION 1: Identification

1.1. Product identifier

3M™ Abrasive Product, 566A Flap Discs: Types 27, 29

1.2. Recommended use and restrictions on use

Recommended use

Abrasive Product

1.3. Supplier’s details
MANUFACTURER:

3M

DIVISION:

Abrasive Systems Division

ADDRESS:

3M Center, St. Paul, MN 55144-1000, USA

Telephone:

1-888-3M HELPS (1-888-364-3577)

1.4. Emergency telephone number

1-800-364-3577 or [phone] (24 hours)

SECTION 2: Hazard identification

2.1. Hazard classification

Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200.

2.2. Label elements

Signal word

Not applicable.

Symbols

Not applicable.

Pictograms

Not applicable.

Notes to Physician:

Not applicable

2.3. Hazards not otherwise classified

None.

3M™ Abrasive Product, 566A Flap Discs: Types 27, 29 02/17/14

__________________________________________________________________________________________

Page 2 of 10

60% of the mixture consists of ingredients of unknown acute oral toxicity.

SECTION 3: Composition/information on ingredients

Ingredient C.A.S. No. % by Wt

Zirconium Oxide Mineral 1314-23-4 5 - 10
Aluminum Oxide Mineral (non-fibrous) 1344-28-1 5 - 15
Inorganic Fluoride 15096-52-3 1 - 10 Trade Secret *
Additive Trade Secret* 1 - 5
Titanium Dioxide 13463-67-6 0.1 - 2 Trade Secret *
Limestone 1317-65-3 2 - 10
Cured Resin Mixture 10 - 30
Cloth Backing Mixture 20 - 30
Fiberglass plate Mixture 20 - 25

*The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade
secret.

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation:

Remove person to fresh air. If you feel unwell, get medical attention.

Skin Contact:

Wash with soap and water. If signs/symptoms develop, get medical attention.

Eye Contact:

Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get
medical attention.

If Swallowed:

No need for first aid is anticipated.

4.2. Most important symptoms and effects, both acute and delayed

See Section 11.1. Information on toxicological effects.

4.3. Indication of any immediate medical attention and special treatment required

Not applicable

SECTION 5: Fire-fighting measures

5.1. Suitable extinguishing media

In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.

5.2. Special hazards arising from the substance or mixture

None inherent in this product.

Hazardous Decomposition or By-Products

Substance Condition

Carbon monoxide During Combustion
Carbon dioxide During Combustion

3M™ Abrasive Product, 566A Flap Discs: Types 27, 29 02/17/14

__________________________________________________________________________________________

Page 3 of 10

5.3. Special protective actions for fire-fighters

No unusual fire or explosion hazards are anticipated.

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Observe precautions from other sections. Refer to other sections of this SDS for information regarding physical and health
hazards, respiratory protection, ventilation, and personal protective equipment.

6.2. Environmental precautions

Not applicable. Avoid release to the environment.

6.3. Methods and material for containment and cleaning up

Not applicable. Seal the container.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

Avoid breathing of dust created by sanding, grinding or machining. Damaged product can break apart during use and cause
serious injury to face or eyes. Check product for damage such as cracks or nicks prior to use. Replace if damaged. Always
wear eye and face protection when working at sanding or grinding operations or when near such operations. Avoid release to
the environment. Combustible dust may form by action of this product on another material (substrate). Dust generated from
the substrate during use of this product may be explosive if in sufficient concentration with an ignition source. Dust deposits
should not be allowed to accumulate on surfaces because of the potential for secondary explosions.

7.2. Conditions for safe storage including any incompatibilities

No special storage requirements.

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

Occupational exposure limits

Ingredient C.A.S. No. Agency Limit type Additional Comments

ZIRCONIUM COMPOUNDS 1314-23-4 Amer Conf of

Gov. Indust.
Hyg.

TWA(as Zr):5
mg/m3;STEL(as Zr):10 mg/m3

ZIRCONIUM COMPOUNDS 1314-23-4 US Dept of

Labor - OSHA

TWA(as Zr):5 mg/m3

Limestone 1317-65-3 US Dept of

Labor - OSHA

TWA(as total dust):15
mg/m3;TWA(respirable

fraction):5 mg/m3
Aluminum Oxide Mineral (non­fibrous)

1344-28-1 Chemical

Manufacturer
Rec Guid

TWA:1 fiber/cc

Aluminum Oxide Mineral (non­fibrous)

1344-28-1 US Dept of

Labor - OSHA

TWA(as total dust):15

mg/m3;TWA(respirable

fraction):5 mg/m3
Aluminum, insoluble compounds 1344-28-1 Amer Conf of

Gov. Indust.
Hyg.

TWA(respirable fraction):1

mg/m3

Titanium Dioxide 13463-67-6 Amer Conf of TWA:10 mg/m3