3M B1798221, 60010016339, 60455033229, 60455031298, 60455047021 User Manual

3M™ Abrasive Products, 216U, 236U 07/22/15

__________________________________________________________________________________________

Page 1 of 9

Safety Data Sheet

Copyright,2015,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.

Document Group:

08-8962-6

Version Number:

10.13

Issue Date:

07/22/15

Supercedes Date:

04/07/15

SECTION 1: Identification

1.1. Product identifier

3M™ Abrasive Products, 216U, 236U

1.2. Recommended use and restrictions on use

Recommended use

Abrasive Product

1.3. Supplier’s details
MANUFACTURER:

3M

DIVISION:

Abrasive Systems Division

ADDRESS:

3M Center, St. Paul, MN 55144-1000, USA

Telephone:

1-888-3M HELPS (1-888-364-3577)

1.4. Emergency telephone number

1-800-364-3577 or [phone] (24 hours)

SECTION 2: Hazard identification

2.1. Hazard classification

Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200.

2.2. Label elements

Signal word

Not applicable.

Symbols

Not applicable.

Pictograms

Not applicable.

2.3. Hazards not otherwise classified

This document is specific to the supplied product. For complete assessment, when determining the degree of hazard, the
material being abraded must also be considered.

SECTION 3: Composition/information on ingredients

Ingredient C.A.S. No. % by Wt

3M™ Abrasive Products, 216U, 236U 07/22/15

__________________________________________________________________________________________

Page 2 of 9

Aluminum Oxide (non-fibrous) 1344-28-1 10 - 45
Lubricant 68424-16-8 1 - 5
Titanium Dioxide 13463-67-7 0.25 - 1.5
Paper Backing None 20 - 70
Cured Resin Mixture 20 - 50
Hookit Backing Mixture 0 - 10
PSA Backing Mixture 0 - 5

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation:

Remove person to fresh air. If you feel unwell, get medical attention.

Skin Contact:

Wash with soap and water. If signs/symptoms develop, get medical attention.

Eye Contact:

Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get
medical attention.

If Swallowed:

No need for first aid is anticipated.

4.2. Most important symptoms and effects, both acute and delayed

See Section 11.1. Information on toxicological effects.

4.3. Indication of any immediate medical attention and special treatment required

Not applicable

SECTION 5: Fire-fighting measures

5.1. Suitable extinguishing media

In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.

5.2. Special hazards arising from the substance or mixture

None inherent in this product.

Hazardous Decomposition or By-Products

Substance Condition

Carbon monoxide During Combustion
Carbon dioxide During Combustion

5.3. Special protective actions for fire-fighters

No special protective actions for fire-fighters are anticipated.

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Observe precautions from other sections.

6.2. Environmental precautions

3M™ Abrasive Products, 216U, 236U 07/22/15

__________________________________________________________________________________________

Page 3 of 9

Not applicable.

6.3. Methods and material for containment and cleaning up

Not applicable.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

For industrial or professional use only. Avoid breathing of dust created by sanding, grinding or machining. Combustible dust
may form by action of this product on another material (substrate). Dust generated from the substrate during use of this
product may be explosive if in sufficient concentration with an ignition source. Dust deposits should not be allowed to
accumulate on surfaces because of the potential for secondary explosions.

7.2. Conditions for safe storage including any incompatibilities

No special storage requirements.

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

Occupational exposure limits

If a component is disclosed in section 3 but does not appear in the table below, an occupational exposure limit is not available
for the component.

Ingredient C.A.S. No. Agency Limit type Additional Comments

Aluminum Oxide (non-fibrous) 1344-28-1 CMRG TWA:1 fiber/cc
Aluminum Oxide (non-fibrous) 1344-28-1 OSHA TWA(as total dust):15

mg/m3;TWA(respirable
fraction):5 mg/m3

Aluminum, insoluble compounds 1344-28-1 ACGIH TWA(respirable fraction):1

mg/m3

A4: Not class. as human
carcin

Titanium Dioxide 13463-67-7 CMRG TWA(as respirable dust):5

mg/m3
Titanium Dioxide 13463-67-7 OSHA TWA(as total dust):15 mg/m3
Titanium Dioxide 13463-67-7 ACGIH TWA:10 mg/m3 A4: Not class. as human

carcin

ACGIH : American Conference of Governmental Industrial Hygienists
AIHA : American Industrial Hygiene Association
CMRG : Chemical Manufacturer's Recommended Guidelines
OSHA : United States Department of Labor - Occupational Safety and Health Administration
TWA: Time-Weighted-Average
STEL: Short Term Exposure Limit
CEIL: Ceiling

8.2. Exposure controls

8.2.1. Engineering controls

Provide appropriate local exhaust ventilation for sanding, grinding or machining. Use general dilution ventilation and/or local
exhaust ventilation to control airborne exposures to below relevant Exposure Limits and/or control
dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment. Provide local exhaust at
process emission sources to control exposure near the source and to prevent the escape of dust into the work area. Ensure that
dust-handling systems (such as exhaust ducts, dust collectors, vessels, and processing equipment) are designed in a manner to
prevent the escape of dust into the work area (i.e., there is no leakage from the equipment).

8.2.2. Personal protective equipment (PPE)

Eye/face protection