Hall Tree
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Part List
A.
To p
1 Pc.
F.
Stretcher
1 Pc.
G.
Stretcher
1 Pc.
H.
Stretcher
1 Pc.
J.
Stretcher
2 Pcs.
K.
Shelf
1 Pc.
B.
Side Frame
1 Pc.
L.
Seat
1 Pc.
N.
Base
1 Pc.
D.
Back Post
2 Pcs.
C.
Side Frame
1 Pc.
M.
Seat Frame
1 Pc.
O.
Divider
1 Pc.
E.
Back Post
1 Pc.
P.
Side Frame
1 Pc.
I.
Back Panel
2 Pcs.
Q.
Side Frame
1 Pc.
Basket
2 Pcs.
Refer to later page(s) of these
instructions for basket assembly.
R.
Hardware List
M3x12
Hex Wrench
1 pc.
Small Wrench
1 pc.
Head Cap Bolt
45 pcs. (+1 extra)
M x613
Tapered Bolt (short)
16 pcs. (+1 extra )
Spring Washer
45 pcs. (+1 extra)
M x638
Tapered Bolt (medium)
8 pcs. (+1 extra )
Flat Washer
45 pcs. (+1 extra)
M6x16
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
Wood Screw
for Hook
8 pcs. (+1 extra)
M x670
Tapered Bolt (long)
4 pcs. (+1 extra )
Hook
4 pcs.
M3.5x8
Wood Screw
for Back Panel
12 pcs. (+1 extra)
Assembly Instructions 2/7
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
STEP 1
Attach Stretchers (F) and (G)
to Back Posts (D) and (E) with
Flat Washers, Spring Washers and
Head Cap Bolts, tightening the bolts
only half way. (See Figure 1)
Figure 1
G
F
D
E
D
Head Cap Bolt
Spring Washer
Flat Washer
C
Figure 2
STEP 2
Attach unit and Stretcher (H) to Side Frame (B)
with Flat Washers, Spring Washers and
Head Cap Bolts, tightening the bolts only half way.
(See Figure 2)
Attach Side Frame (C) to unit with Flat Washers,
Spring Washers and Head Cap Bolts, tightening
the bolts only half way.
H
B
Assembly Instructions 3/7
STEP 3
Slide Back Panels (I) into position.
Attach Top (A) and Shelf (K) to unit with
Flat Washers, Spring Washers and
Head Cap Bolts, tightening
the bolts only half way.
Tighten all bolts used
in all steps.
I
A
K
I
Figure 3
Wood Screw
for Back Panel
STEP 4
Turn the unit to its’ upright position.
Attach Back Panels (I) to unit by inserting
Wood Screws for Back Panel into the pre-drilled holes. (See Figure 3)
STEP 5
Assembly Instructions 4/7
Attach Stretchers (J) and Seat Frame (M) to Side Frame (Q)
with Flat Washers, Spring Washers, Head Cap Bolts and
Tapered Bolts (medium), tightening the bolts
only half way. (See Figure 4)
Attach Side Frame (P) to unit with Flat Washers,
Spring Washers, Head Cap Bolts and
Tapered Bolts (medium).
Tighten all bolts used in this step.
Figure 4
Tapered Bolt
(medium)
P
M
J
J
STEP 6
Attach Base (N) to unit with Flat Washers,
Spring Washers and Head Cap Bolts.
Attach Divider (O) to unit with
Tapered Bolts (medium).
Attach Seat (L) to unit
with Flat Washers,
Spring Washers
and Head Cap Bolts.
Q
O
L
N
Basket (R)
Tapered Bolt
(short)
Assembly Instructions 5/7
R2
R1
STEP 7
Attach Basket Side (R2) to Basket Unit (R1)
with clips and Tapered Bolts (short). (See Figures 5 and 6)
STEP 8
Attach Basket Side (R2) to unit
with clips and Tapered Bolts (short).
Figure 5
Figure 6
R2
Tapered Bolt
(short)
Part List
R1.
Basket Unit
2 pcs.
R2.
Basket Side
4 pcs.
Assembly Instructions 6/7
Wood Screw
for Hook
Hook
R
R
STEP 9
Attach unit from Step 4 to unit from Step 6 with Tapered Bolts (long).
Attach Hooks to unit by inserting Wood Screws for Hook into the
pre-drilled holes of back panels. (See Figure 7)
Slide Baskets (R) into position.
Tapered Bolt
(long)
Figure 7
To level the unit, adjust the adjustable levers on the bottom of unit.
(See Figure 8)
Note: Unit must be level to work property.
Figure 8
Assembly Instructions 7/7
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
STEP 10
Place unit at desired location.
3/8” wall hole
Drill a 3/8” hole in wall in-line with
the pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Machine Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 9)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Anchor in wall
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
Bracket
on wall
Wall Screw
Figure 9
Pre-drilled hole
at top of unit
Machine Screw
Hardware List
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
Drill 3/8” hole in wall
M3.5x40
Wall Screw
1 pc. (+1 extra)
Top of unit
M4x10
Machine Screw
1 pc. (+1 extra)
CARE INSTRUCTIONS
NEVER
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
Do not write
directly on surface.
PREVENT
MARKING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not use rubber
based placemats.
PREVENT
DISCOLORING
CLEAN
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Loading...