Industrial Drafting Table
Assembly Instructions
"Please do not load more than 30 lb. when table top is fully raised".
Page | 1
A.
Quantity
B.
Quantity
C.
Quantity
D.
Quantity
1.
Quantity
2.
Quantity
3.
Quantity
4.
Quantity
5.
Quantity
6.
Quantity
7.
Quantity
8.
Quantity
9.
Quantity
S
crew
Dia1/8”x
5/8”L
10.
Quantity
11.
Quantity
Industrial Drafting Table
Parts List
Please review all parts and hardware before disposing of any packaging. Before beginning assembly, separate
each type of hardware. Carefully study the diagrams below and check that you have all parts indicated. Call
Customer Service if missing hardware. Using the incorrect hardware will cause damage.
of 1
Top Panel
Back Stretcher
Left Leg Frame
of 1
of 4
Small Bolts ∅1/4"x3/4"
of 1
of 1
Right Leg Frame
of 8
Bolts ∅1/4"x1-5/8
of 12
Flat Washers
of 12
Flat Washers
of 2
Bracket
Plastic Strap
of 4
Wall Brackets
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew the finish.
Avoid rubbing or scratching the surface with rough or
abrasive objects.
No.2 Phillips Screwdriver (Not Included)
Assembly Tool Required:
of 1
Allen Wrench
of 2
of 2
Wall Anchor
of 2
of 2
Screw Dia1/8”x1-3/8”L
For replacement parts or questions, please call
customer service.
Tool List: 3/16" Drill Bit, Drill, Tape Measure and Pencil.
Page | 2
4
1
3
Industrial Drafting Table
Assembly Instructions
4
3
1
D
Attach Left Leg Frame (B) and
Right Leg Frame (C) to Back
Stretcher (C) using Small Bolts (1),
Spring Washers (3) and Flat
Washers (4).
Tighten bolts with
screwdriver.
Phillips
Figure 1
B
Insert assembled unit into Top
Panel (A).
D
Figure 2
Page | 3
5
2
3
4
Insert Bolts (2), Spring Washers
(3), and Flat Washers (4) into holes
in Leg Frames.
Tighten bolts with Allen Wrench (5).
Figure 3
Find a desired location. Mark 2
locations for screws on wall
One screw (for each unit) must be
attached directly into a wall stud.
Wall anchor is not needed when
mounting to wall stud.
Drill one of the marking 3/16" hole
(for each unit).
Figure 4
Page | 4
8
Insert Wall Anchor (8) into the hole
on wall as shown.(When doing
this,you will need a hammer help
you)
Figure 5
Using the Phillips head
screwdriver, install screw (11)
through holes on Wall Brackets
(10) into Wall Anchors to attach
Wall Brackets (10) onto Wall
Anchors.
Figure 6
Page | 5
Attach brackets (6) to back panel
using screws (9).
Tighten screws (9) using Philips
screwdriver.
Figure 7
10
7
FURNITURE
10
FURNITURE
7
Move this item
Lace an end of the 2pcs nylon
restraint strap (7) down through
bracket (6)(10). bring both ends
together and slide the beaded end
of the strap through the key hole
shaped slot on the other end. pull
down on the beaded end until it
snap-locks into the keyhole.
Check to make sure the strap is
securely laced and locked to the
brackets
Figure 8
Page | 6
To open top, simply pull up. Guide
back down to close.
Now your Industrial Drafting Table
is ready to use!
Figure 9
Page | 7
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Page | 8
Loading...