1. Asegúrese que el cable eléctrico esté conectado a un
Calor Alto
+
+
tomacorriente eléctrico en funcionamiento.
2. Verifique la posición de su Termostato. El Calefactor puede
haberse apagado por haber alcanzado la posición de temperatura
deseada.
Si usted tiene un problema que no pueda ser resuelto siguiendo los
pasos enumerados arriba, comuníquese con Asistencia Técnica al
800-233-0268, de lunes a viernes, entre las 8 a.m. y las 5 p .m. EST.
IMPORTANT INSTRUCTIONS -
OPERATING MANUAL
Figura 6
Si usted pierde su mando a distancia, por favor Cliente de llamada
Serive para ordenar un reaplacement en 1-800 -233-0268, de lunes
a viernes, entre las 8 a.m. y las 5 p .m. (Horario Estándar del Este de
los Estados Unidos).
ELEMENTOS DE SEGURIDAD
1. Hay un protector de sobrecarga térmica incorporado para evitar
el sobrecalentamiento.
2. Cuando se alcance una temperatura de sobrecalentamiento, el
Calefactor se apagará automáticamente. Sólo podrá retomar el
funcionamiento cuando el usuario reinicie la unidad.
Para Reiniciar el Calefactor:
1. Desconecte el Calefactor y espere 15 minutos hasta que la
Unidad se enfríe.
2. Después que el Calefactor se hay a enfriado, conecte la unidad a
un tomacorriente eléctrico de 120V~ y siga las instrucciones de
funcionamiento descriptas en este manual.
CONSEJOS DE SOLUCIÓN DE PROBLEMAS
Si su calefactor se apaga inesperadamente o no funciona, el
elemento de seguridad arriba mencionado podría haber sido activado
para evitar el sobrecalentamiento.
MANTENIMIENTO
ADVERTENCIA:SIEMPRE DESCONECTE EL CABLE
ELÉCTRICO ANTES DE MOVER, REP ARAR o LIMPIAR
EL CALEFACT OR.
ADVER TENCIA: ¡NO SUMERJA EL CALEFACTOR EN AGUA!
LIMPIEZA: ¡IMPORTANTE! Limpie la parrilla del Calefactor con el
accesorio de cepillo de aspiración de su aspiradora. Esto quitará pelusas
y suciedad del interior del Calefactor. Limpie el cuerpo del Calefactor
con un trapo suave.
NO INTENTE DESARMAR EL CALEF ACTOR.
PRECAUCIÓN:
diluyente, limpiadores duros, etc., ya que dañarán
el Calefactor. NUNCA use ALCOHOL O
SOLVENTES.
REPARACIONES: Toda otra reparación, con excepción del
mantenimiento general del usuario, debe ser realizada por un
representante autorizado de reparaciones. Llame al 1-800-233-0268,
de lunes a viernes, entre las 8 a.m. y las 5 p .m. EST para conocer la
ubicación de su centro de reparaciones más cercano.
ALMACENAMIENTO: Almacene el Calefactor con estas
instrucciones en la caja original en un lugar fresco y seco.
No use gasolina, bencina,
GARANTÍA LIMITADA
EN CASO DE NECESIT AR PIEZAS, COMUNÍQ UESE CON EL F ABRICANTE P ARA PIEZAS DE REPUEST O AMP ARAD AS
POR LA GARANTÍA. SE DEBE INCLUIR UNA COPIA DEL RECIBO DE COMPRA CON EL TIPO Y ESTILO DEL
CALEFACTOR, UBICADOS EN LA PARTE INFERIOR DEL APARATO.
Este producto está garantizado por tres años a partir de la fecha de compra contra defectos de fabricación y/o de
materiales. A nuestra discreción, las piezas que resulten defectuosas se reemplazarán o se repararán, o bien se
reemplazará el producto entero.
Si se necesita reparación eléctrica o mecánica durante el período de garantía, envíe el producto completo, con porte
pagado, al centro de servicio más cercano. Llame al número que se indica más adelante para encontrar el centro de
servicio más cercano.
Si necesita una pieza de repuesto, debe especificar el tipo y el estilo del aparato . Esta información puede encontrarse en la
parte inferior del aparato. En cualquiera de los casos, es necesario que envíe una copia del recibo de compra.
Esta garantía no tiene validez si el daño se debe a un accidente, manejo o uso indebido, daños de transporte, abuso, mal
uso, reparaciones o intentos de reparación no autorizados, o al uso comercial del producto.
TODAS LAS GARANTÍAS, MANIFIESTAS O IMPLÍCITAS, RIGEN DURANTE TRES AÑOS A PARTIR DE LA FECHA DE
COMPRA ORIGINAL. ESTA GARANTÍA NO CUBRE EN NINGÚN CASO RESPONSABILIDAD POR DAÑOS DIRECTOS
O INDIRECTOS POR CAUSA ALGUNA.
En algunos estados no se permiten limitaciones de la duración de una garantía implícita, ni la exclusión o limitación de
daños directos o indirectos, por lo cual las limitaciones y exclusiones anteriores pueden quedar sin vigencia en su caso.
Esta garantía le otorga derechos legales específicos. Usted podría tener otros derechos que varían de un estado a otro.
CYCLONIC CERAMIC HEATER with
FRESH AIR IONIZER and REMOTE CONTROL
MODEL 6000
This Heater is for residential use only.
It is not intended to be used in commercial or industrial settings.
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE,
INSTALL, OPERATE OR MAINTAIN THE PR ODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY
INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR
PROPER TY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
Para piezas de repuesto, favor de llamar al 1-800-233-0268, DE LUNES A VIERNES, DE 8:00 A.M. a 5:00 P.M., HORA
ESTÁNDAR DEL ESTE. “POR FAVOR, NO ENVÍE EL APARATO AL LUGAR DONDE LO COMPRÓ.”
Mencione el tipo y el estilo del producto (ubicados en la parte inferior del aparato) al llamar.
PARA APOYO TÉCNICO Y UBICACIONES DE CENTROS DE SERVICIO:
Para cualquier pregunta o comentario, o para solicitar información sobre el centro de servicio más cercano a su domicilio,
FAVOR DE LLAMAR A NUESTRA “LÍNEA GRATUITA” AL 1-800-233-0268, DE LUNES A VIERNES,
DE 8:00 A.M. A 5:00 P.M., HORA ESTÁNDAR DEL ESTE.”
Mencione el nombre y el número de modelo del producto al llamar.
Appliance Service Dept. 300 Confederate Drive Franklin, TN 37064.
PARA PIEZAS DE REPUESTO:
Para más información, visite nuestro sitio en la Web: www.laskoproducts.com
Rev. A 6/05
¡POR FAVOR, NO ENVÍE EL PRODUCTO A ESTA DIRECCIÓN!
El manual imprimió en la China
8
6000ES
Rev. A 6/05
SAVE THESE INSTRUCTIONS
1
6000ES
MODEL 6000
MODELO 6000
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions should always
be followed to reduce the risk of fire, electric shock and injury to persons,
including the following:
1.Read all instructions before using this Heater.
2. Use this Heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire,
electrical shock, or injury to persons.
3.Make certain that the power source conforms to the electrical requirements of the Heater.
4.Extreme caution is necessary when any Heater is used by or near children or invalids and whenever the Heater is
left operating unattended.
5.This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is
intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, rev erse the plug. If it still does not
fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
6. DO NOT plug Heater into any other cord connected device, such as a power strip, surge protector, multiple outlet
adapters or outlet-type air fresheners. The use of such devices may create a fire hazard. Plug unit directly into a 120V
wall outlet only.
7.Avoid the use of extension cords because the extension cord ma y o v erheat and cause a risk of fire. However, if you have
to use an extension cord, minimize the risk of ov erheating by ensuring that they are UL listed. The cord shall be a 3-wire,
grounding type, with No. 14 AWG minimum size and rated not less than 1875 watts. NEVER use a single extension cord
to operate more than one Heater.
8. Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, has been dropped or damaged in any
manner. Return Heater to authorized service facility for examination, electrical or mechanical adjustment or repair.
9. To disconnect Heater, turn controls to OFF, then remove plug from outlet.
10. Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.
WARNING: DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER
WHEN SERVICING OR MOVING THE HEATER. ALWAYS UNPLUG THE POWER CORD.
11. Do not insert or allow fingers or foreign objects to enter any v entilation or e xhaust opening as it may cause an electric shock,
fire, or damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.
12. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed,
where openings may become blocked.
13. Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning.
Locate the Pow er Cord so the Heater or other objects are not resting on it. Do not run Po wer Cord under carpeting. Do not
cover P ow er Cord with throw rugs, runners, or the like . Arrange P ow er Cord awa y from room traffic and where it will not be
tripped over.
14. This Heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving
this Heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet
(0.9 m) from the front of the Heater and keep them at least 1 foot (0.3 m) from the sides and rear.
15. A Heater has hot and arcing or sparking parts inside. Do not use the Heater in areas where gasoline, paint, or flammab le
liquids are used or stored. It m ust NOT be used in potentially dangerous locations such as flammable , explosiv e, chemicalladen or wet atmospheres. This Heater is intended for general use ONLY.
16. This Heater is not intended f or use in w et or damp locations. This Heater is not intended for use in bathrooms, laundry areas
and similar indoor locations. Never locate a Heater where it may fall into a bathtub or other water container.
17. Do not use Heater outdoors.
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK – DO NOT USE THIS HEATER WITH ANY
SOLID STATE SPEED CONTROL DEVICES.
FUNCIONAMIENTO
1. Cuidadosamente retire el Calefactor de la bolsa y de la caja.
2. Coloque el Calefactor sobre una superficie firme y plana.
ADVERTENCIA: Los tacos de plástico o hule, tales como las
patas de esta unidad, pueden pegarse a la superficie de los muebles
y/o a los pisos de madera. La unidad podría dejar un residuo capaz
de oscurecer, manchar o dejar marcas permanentes en el acabado
de ciertas superficies de muebles, incluyendo superficies de madera
y/o pisos de madera.
3. Conecte el cable eléctrico a un tomacorriente eléctrico de 120V~.
Asegúrese que el enchufe encaje firmemente en el tomacorriente.
4. El Calefactor emitirá un “bip” cuando lo conecte por primera v ez.
5. ENCIENDA el Calefactor oprimiendo el
6. Al encender el Calefactor, la unidad estará en calor ALTO (1500
vatios) y mostrará la temperatur a actual de la habitación
7. Oprima el botón de Modo para calor BAJO (750 vatios).
8. Para APAGAR el Calefactor, presione el
y desconecte el Calefactor del tomacorriente eléctrico.
POWERMODETIMER
Figura 1
TEMPORIZADOR:
La función de temporizador puede ser activada cuando la pantalla
del Calefactor está en cualquier velocidad o temperatura. Esta
función le permite fijar la cantidad de tiempo que el Calefactor estará
funcionando antes de apagarse automáticamente, de 1 hora a 7
horas. Presionar el
de tiempo, en combinaciones de 1, 2 y 4 horas. Oprimir
continuamente el botón provocará que el temporizador quede fijado
para 7 horas. El Calefactor se apagar á cuando el tiempo fijado haya
transcurrido. La unidad puede volver a encenderse presionando el
Botón de Encendido
(Figura 2)
Botón de T emporizador
.
MODETIMER
Botón de Encendido
Botón de Encendido
TEMP
aumentará la cantidad
(Figura 1)
IONIZER
3. Cuando la temperatura del aire alcance un 1°
temperatura fijada, el Calefactor se encenderá.
NOTA: Es normal que el Calefactor alterne entre ENCENDIDO y
APAGADO para mantener la temperatura FIJADA.
POWERMODETIMER
.
Figura 3
IONIZADOR:
La función de ionizador en este Ventilador funcionará dentro de
cualquier modo de velocidad. Oprima el Botón de Ionizador una
vez para encender esta función y una segunda vez para apagarla.
El Ventilador debe estar ENCENDIDO para que el ionizador esté
en funcionamiento. Cuando el ionizador esté encendido, ayudará a
la purificación del aire de la habitación.
Figura 4
(Figura 4)
IONIZER
FUNCIÓN DE PERSIANA (LOUVER):
Este Calefactor posee una persiana en la parrilla frontal superior que
permite el ajuste vertical del flujo de aire. Deslice el control de la persiana
hacia arriba o hacia abajo para ajustar el flujo de aire a voluntad.
Función De Persiana
TEMP
(Figura 4)
por debajo de la
IONIZER
Rev. A 6/05
SAVE THESE INSTRUCTIONS
2
6000ES
Figura 2
TERMOSTATO:
Oprimir el botón ( ) o el botón ( ) le permite a usted fijar la
temperatura deseada del Calefactor.
1. Oprima el botón ( ) para aumentar la temperatura fijada deseada
o presione el botón (
2. Cuando la temperatura del aire alcance los 2°
temperatura fijada, el Calefactor se apagará.
Rev. A 6/05
) para reducir la temperatura fijada deseada.
(Figura 3)
por encima de la
Figura 5
CONTROL REMOTO:
Todas las funciones ejecutadas con el Control Remoto funcionan
idénticamente a los controles manuales.
1. Instale las dos baterías “AAA” provistas.
2. No mezcle baterías viejas y nuevas. No mezcle baterías alcalinas,
estándar (carbono-zinc) o recargables (níquel-cadmio).
7
(Figura 6)
6000ES
MODELO 6000
MODEL 6000
INFORMACIÓN GENERAL DE SEGURIDAD
Al usar aparatos eléctricos, las precauciones básicas de seguridad
deberan siempre de seguirse para reducir el riesgo de incendio, choque
eléctrico, y daño a personas, incluyenda las siguientes.
1.Lea todas las instrucciones antes de usar este Calefactor.
2. Use este Calefactor solamente como se describe en este manual. Cualquier otro uso no recomendado por el fabricante
podría causar incendio, choque eléctrico o lesiones a personas.
3.Asegúrese que la fuente de alimentación eléctrica sea la adecuada para los requerimientos eléctricos del Calefactor.
4.Es necesario tener extremo cuidado cuando se utiliza cualquier Calefactor junto a o cerca de niños o discapacitados y
siempre que el Calefactor esté en funcionamiento sin atención de otras personas.
5.Este aparato tiene la clavija polarizada (un diente es más ancho que el otro). Esta clavija está diseñada para ser insertada
en un tomacorriente polar de una sola forma a fin de reducir el riesgo de choque eléctrico. Si la cla vija no encaja totalmente
en el tomacorriente, dele vuelta. Si aun así no encaja, consulte a un técnico electricista. No trate de modificar estas
características de seguridad.
6. NO enchufe el Calefactor en ningún otro dispositivo que tenga cables conectados, tales como distribuidores de electricidad,
disyuntores de electricidad, adaptadores de tomacorrientes múltiples o refrescadores de aire enchufables. El uso de tales
dispositivos podría crear un riesgo de incendio. Conecte la unidad directamente a un tomacorriente de pared de 120V únicamente.
7.Evite el uso de cables de alargue porque el cable de alargue podría sobrecalentarse y provocar un riesgo de incendio . Sin
embargo, si tiene que usar un cable de alargue , minimice el riesgo de sobrecalentamiento garantizando que el mismo esté
aprobado por la UL. El cable deberá ser uno de 3 alambres, con conexión a tierra, con un tamaño mínimo N° 14 AWG y
clasificado para no menos de 1875 vatios. NUNCA use un solo cable de alargue para operar más de un Calefactor.
8. No opere ningún Calefactor con un cable o enchufe dañados o después que el Calefactor funcione mal, se haya caído o
haya sido dañado de alguna manera. Lleve el Calefactor a la empresa de reparaciones autorizada para su revisión, ajuste
eléctrico o mecánico o reparación.
9. Para desconectar el Calef actor, coloque los controles en la posición APAGADO, luego retire el enchufe del tomacorriente.
10. Siempre desconecte el Calefactor cuando no esté en uso. Desconecte el cable eléctrico antes de reparar o mover el Calef actor.
ADVERTENCIA: NO DEPENDA DEL INTERRUPTOR DE ENCENDIDO / APAGADO COMO ÚNICO MEDIO
PARA DESCONECTAR LA ELECTRICID AD CU ANDO ESTÉ REP ARANDO O TRASLAD ANDO EL CALEF ACT OR.
SIEMPRE DESCONECTE EL CABLE ELÉCTRICO.
11. No inserte ni permita que alguien introduzca dedos u objetos extraños en cualquier abertura de ventilación o de escape ya
que podrían causar un choque eléctrico o un incendio, o dañar el Calefactor. No bloquee ni toque indebidamente el
Calefactor de ninguna manera mientras esté en funcionamiento.
12. Para evitar un posib le incendio, no bloquee las tomas o los escapes de aire de ninguna manera. No coloque sobre superficies
suaves, como una cama, donde las aberturas podrían resultar bloqueadas.
13. Siempre coloque el Calefactor sobre una superficie estable, lisa y nivelada cuando esté en funcionamiento, par a evitar la
posibilidad de que el Calefactor se caiga. Coloque el Cable Eléctrico de modo tal que el Calefactor u otros objetos no estén
apoyados sobre él. No introduzca el Cable Eléctrico debajo de alfombr as. No cubra el Cable Eléctrico con tapetes, alfombrillas
u objetos similares. Coloque el Cable Eléctrico lejos de los lugares transitados de la habitación y donde nadie pueda
tropezarse con el mismo.
14. Este Calefactor está caliente cuando se lo utiliza. Para evitar quemaduras, no permita que la piel desnuda toque las
superficies calientes. Siempre use la agarr adera cuando traslade este Calefactor. Mantenga los materiales combustibles,
tales como muebles, almohadas, ropa de cama, papeles , ropa y cortinas a una distancia de por lo menos 3 pies (0.9 m) del
frente del Calefactor y manténgalas a una distancia de por lo menos 1 pie (0.3 m) de los laterales y de la parte posterior.
15. Un Calefactor tiene partes calientes y con arcos o chispas en su interior. No use el Calefactor en áreas donde se utilice o
almacene gasolina, pintura o líquidos inflamables. NO debe ser usado en lugares potencialmente peligrosos tales como
atmósferas inflamables, explosivas, cargadas de sustancias químicas o húmedas. Este Calefactor está diseñado SÓLO
para uso general.
16. Este Calefactor no está diseñado para ser usado en lugares húmedos o mojados. Este Calefactor no está diseñado para
usarse en baños, áreas de lavandería y similares emplazamientos interiores. Nunca coloque un Calefactor donde podría
caer dentro de una tina de baño o cualquier otro contenedor de agua.
17. No use el Calefactor al aire libre.
ADVERTENCIA: REDUZCA EL RIESGO DE INCENDIO O CHOQUE ELÉCTRICO – NO USE ESTE
CALEFACTOR CON NINGÚN DISPOSITIVO DE CONTROL DE VELOCIDAD DE ESTADO SÓLIDO.
OPERATION
1. Carefully remove the Heater from the bag and the carton.
2. Place the Heater on a firm, level surface.
WARNING: Plastic or rubber tabs, like the feet on this unit, may
stick to furniture surfaces and/or hardwood floors. The unit ma y leav e
a residue that could darken, stain or leave permanent blemishes on
the finish of certain furniture surfaces, including wood surfaces, and/
or hardwood floors.
3. Plug the cord set into a 120V~ electrical outlet. Be sure plug fits
tightly in outlet.
4. The Heater will “beep” when initially plugged in.
5. Turn the Heater ON by pressing the
6. Upon turning the Heater on, the unit will be in HIGH heat (1500
Watts) and will display the current room temperature
7. Press the Mode button for LOW heat (750 Watts).
8. To turn the Heater OFF, press the
the Heater from the electrical outlet.
POWERMODETIMER
Figure 1
TIMER:
The Timer Function may be activated when the Heater is in any
speed or temperature. This function allows you to set the length of
time the Heater will run before turning itself off, from 1 hour to 7
hours. Pressing the
combinations of 1, 2 and 4 hours. Contin uously pressing the b utton
will result in the timer being set for 7 hours. The Heater will turn off
when the set time has elasped. The unit can be turned back on by
pressing the
Figure 2
(Figure 2)
Power Button
Timer Button
.
Power Button
Power Button
TEMP
will increase the length of time , in
MODETIMER
.
(Figure 1)
and unplug
IONIZER
THERMOSTAT:
Pressing the ( ) or ( ) button allows you to set the desired
temperature of the Heater.
1. Press the ( ) to increase the desired set temperature or press
the ( ) to decrease the desired set temperature.
2. When the air temperature reaches 2°
the Heater will shut off.
3. When the air temperature reaches 1°
the Heater will turn on.
NOTE: It is normal for the Heater to cycle ON and OFF as it
maintains the SET temperature.
Figure 3
IONIZER:
The ionizer function on this Fan will operated within an y speed mode.
Press the Ionizer Button once to turn this function on and a second
time to turn it off. The F an must be ON for the ionizer to be functional.
When the ionizer is turned on this will assist in the purification of the
room air.
Figure 4
(Figure 4)
LOUVER FUNCTION:
This Heater has a louver on the top front grill that allow for vertical
adjustment of air flow. Slide the louver control up or down to adjust
the air flow as desired.
(Figure 3)
POWERMODETIMER
IONIZER
(Figure 5)
Louver Function
TEMP
above the set temperature,
below the set temperature,
IONIZER
Rev. A 6/05
CONSERVE ESTAS INSTRUCCIONES
6
6000ES
Rev. A 6/05
3
Figure 5
6000ES
MODEL 6000
REMOTE CONTROL:
All the functions performed with the Remote Control work identically
to the manual controls.
1. Install the two “AAA” batteries supplied.
2. Do not mix old and new batteries. Do not mix alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium) batteries.
Front View
of Remote
Figure 6
If you lose your remote control, please call Customer Service to order a replacement at 1-800-233-0268, Monday through Friday, between the hours of 8:00 a.m. and 5:00 p.m. EST.
SAFETY FEATURE
1. A thermal overload protector is built in to pre vent overheating.
2. When an overheat temperature is reached, the Heater will be
automatically shut off. It can only resume operation when the
user resets the unit.
To Reset Heater:
1. Unplug the Heater and wait 15 minutes for the Heater to cool down.
2. After the Heater has cooled down, plug the unit into a 120V~
electrical outlet and follow the operation instructions described
in this manual.
(Figure 6)
(Figure 6)
Back View
of Remote
+
+
TROUBLE SHOOTING TIPS
If your heater shuts off unexpectedly or fails to operate, one of
the above-mentioned safety feature may have been activated to
prevent overheating.
1. Be sure the power cord is plugged into a working electrical outlet.
2. Check your Thermostat setting. The Heater may be off because
it has reached the desired temperature setting.
If you have a problem that can not be resolve by the steps listed
above, contact Technical Assistance at 800-233-0268, Monday
through Friday, between the hours of 8am and 5pm EST.
MAINTENANCE
WARNING:AL WAYS UNPLUG THE CORD BEFORE MOV-
ING OR SERVICING.
WARNING:DO NOT IMMERSE HEATER IN WATER.
CLEANING: IMPORTANT! Clean the Heater grill and side in-
takes with the v acuum brush attachment of y our vacuum cleaner.
This will remove lint and dirt from the inside of the Heater. Clean
the body of the Heater with a soft cloth.
DO NOT ATTEMPT TO TAKE APART THE
HEATER.
CAUTION:Do not use gasoline, benzine, thinner, harsh
cleaners, etc., as they will damage the Heater. NEVER
use ALCOHOL OR SOLVENTS.
SERVICING: All other ser vicing, with the exception of general
user-maintenance, should be performed by an authorized service representative. Call 1-800-233-0268, Monday through Friday, between the hours of 8am and 5pm EST for the location of
your nearest service center.
STORAGE: Store the Heater with these instructions in the original
carton in a cool, dry place.
INSTRUCCIONES IMPORTANTES -
MANUAL DE USO
CALEFACTOR CICLÓNICO CERÁMICO con
IONIZADOR DE AIRE FRESCO y CONTROL REMOTO
MODELO 6000
Este Calefactor es para uso residencial únicamente.
No está destinado para uso en ambientes comerciales o industriales.
LEA Y GUARDE ESTAS INSTRUCCIONES
LIMITED W ARRANTY
SHOULD ACCESSORY PARTS BE NEEDED, CONTACT THE MANUFACTURER FOR IN-WARRANTY
REPLACEMENT PARTS. A COPY OF PROOF-OF-PURCHASE MUST BE INCLUDED ALONG WITH THE TYPE
This product is warranted for three y ears from the date of purchase against defects in workmanship and/or materials. At our
option, parts that prove to be defective will either be repaired or replaced or the whole product will be replaced.
Should electrical or mechanical repair become necessary during the warranty period, send your complete product, postage or
freight pre-paid to the nearest service center. Call the number below for the service station nearest you.
Should a part need replacement, you must give us the type and style of your appliance. You will find this at the bottom of the
appliance. In either case, a copy of your proof-of-purchase is requested.
This warranty does not apply if the damage occurs because of accident, improper handling or operation, shipping damage,
abuse, misuse, unauthorized repairs made or attempted, of the use of the product for commercial service.
ALL W ARRANTIES, EXPRESSED OR IMPLIED , LAST FOR THREE YEARS FR OM THE D A TE OF ORIGINAL PURCHASE.
THIS W ARRANTY DOES NOT CO VER LIABILITY FOR INCIDENT AL OR CONSEQ UENTIAL DAMA GES FOR ANY CA USE
WHATSOEVER.
Some states do not allow limitations on how long any implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so that the above limitations and exclusions may not apply to you. This warranty gives you specific
legal rights. You may also have rights which vary from state to state.
For any questions, comments or the location of your nearest service center, PLEASE CALL OUR TOLL-FREE “HOTLINE”
Rev. A 6/05
AND STYLE, WHICH IS LOCATED ON THE BOTTOM OF YOUR APPLIANCE.
FOR PARTS:
For Replacement parts please call: 1-800-233-0268, MONDAY THROUGH FRIDAY, BETWEEN THE HOURS OF 8 AM
and 5 PM EST. “PLEASE DO NOT RETURN PRODUCT TO PLACE OF PURCHASE”
Reference the type and style of product (located on the underside of the product) when you call.
FOR TECHNICAL ASSISTANCE AND SERVICE CENTER LOCATIONS:
AT 1-800-233-0268, MONDAY THROUGH FRIDAY, BETWEEN THE HOURS OF 8 AM and 5 PM EST.
Please reference product name and model no. when you call.
Appliance Service Dept. 300 Confeder ate Driv e Franklin, TN 37064.
PLEASE DO NOT SEND PRODUCT TO THIS LOCATION!
For more information please visit our website: www.laskoproducts.com
Manual printed in China
4
6000ES
LEA CUID ADOSAMENTE LAS INSTRUCCIONES ANTES DE
INTENTAR ARMAR, INSTALAR, USAR O DAR MANTENIMIENTO
AL PRODUCTO DESCRITO .
PROTÉJASE A SÍ MISMO Y A LOS DEMÁS CUMPLIENDO CON
TODA LA INFORMACIÓN DE SEGURID AD. EL NO SEGUIR LAS
INSTRUCCIONES PODRÍA RESULTAR EN LESIONES
PERSONALES Y/O DAÑOS A LA PROPIEDAD.
CONSERVE LAS INSTRUCCIONES COMO FUTURA REFERENCIA.
CONSERVE ESTAS INSTRUCCIONES
Rev. A 6/05
5
6000ES
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.