T A B L E O F C O N T E N T S
1.Contents
2.Introduction
3.Features
4.Specifications
5.Amplifier installation
6.7.Features and controls
8.9.10.11. System wiring 12.13. Troubleshooting
V I B E O W N E R ’ S M A N U A L — 1
I N T R O D U C T I O N
Thank you for purchasing the Lanzar VIBE Class-D amplifier. Rest assured you have purchased a quality product designed and engineered to give you many years of uncompromised musical service.
The VIBE Class-D amplifier has been designed using the latest in electronic technology available today.
This mono subwoofer amplifer is the result of advanced high speed switching technology that overcomes the less-efficient classAB design. The VIBE Class-D amplifier reflects your true appreciation for powerful bass reproduction in the mobile environment.
This amplifier is designedd for low-frequency information only and it is not capable of reproducing any mid/high-frequency information.
This is due to the noise introduced into the signal by the switching speed of the power supply, which must be filtered out of the audio signal.
The power supplyy incorporated into VIBE amplifier is a DC to DC switching power supply designed to have adequate headroom for even the most demanding peak and dynamic range found on today’s Cds and recording.
2 — |
V I B E O W N E R ’ S M A N U A L |
F E A T U R E S
CLASS-D DESIGN
Low - frequency information for subwoofer only.
High efficient power
POWER SUPPLIES
Stiffly regulated PWM power supplies.
MOSFET switches maintain rated power over a wide range of battery voltages.
LOW PASS FILTER
Adjustable from 50Hz to 150Hz with a slope of 24dB per octave.
This allows for the adjustment of the upper point of the frequency bandwidth and the respective subwoofer.
VARIABLE SUBSONIC FILTER
Adjustable from 15Hz to 40Hz (VIBE1801D) / 10Hz -40Hz (VIBE3200D) with a slope of 24dB per octave.
This allows for the attenuation of frequencies that are mostly inaudible and cause unnecessary strain on the amplifier.
PROTECTION CIRCUITRY
Protection against thermal, Overload and short circuit conditions.
REMOTE DASH-MOUNT GAIN CONTROL
This amplifier come complete with a compact remote GAIN CONTROLLER which can be conveniently mounted on or under the dashboard of your car.
V I B E O W N E R ’ S M A N U A L — 3
S P E C I F I C A T I O N S
MODEL |
VIBE1801D mono channel amilifier |
VIBE3200D mono channel amilifier |
|
|
RMS Power, INTO 4 Ohms |
1X400W |
1200W |
|
RMS Power, INTO 2 Ohms |
1X800W |
2200W |
|
RMS Power, INTO 1.3 Ohms |
1X900W |
2400W |
|
MAX Power, INTO 1.3 Ohms |
1X1800W |
3200W |
|
BRIDGE MAX Power, INTO 2 Ohms |
1X3600W |
6400W |
|
THD at 1 Watt, 4 Ohm |
0.5% |
0.5% |
|
Signal-to-Noise Ratio, below rated power output |
95 |
95 |
|
Frequency Response, at 1Watt,4 Ohm |
15Hz to 150Hz |
15Hz to 150Hz |
|
Damping Factor at 20Hz, 4 Ohm |
300 |
300 |
|
Low Pass Filter |
50Hz ~ 150Hz |
50Hz ~ 150Hz, 24dB/Octave |
|
Variable Subsonic Filter |
15Hz ~ 40Hz |
10Hz ~ 40Hz, 24dB/Octave |
|
Bass Boost |
0+18dB |
0+18dB |
|
Phase Control |
0 to180 |
0 to180 |
|
Input Sensitivity |
200mV to 8V |
200mV to 8V |
|
Input Impedance |
10K Ohm |
10K Ohm |
|
Line Output Impedance |
100 Ohm |
100 Ohm |
|
Dimensions(Inches) |
10.25”x2.36”x15.10” |
10.25”x2.36”x21.06” |
|
Fuse Rating |
40Ax4 |
250A (Not Included) |
|
|
|
|
4 — |
V I B E O W N E R ’ S M A N U A L |