Heat & Glo LifeStyle SL-950TV-IPI-E User Manual

Size:
4.76 Mb
Download

ÎPara obtener un ejemplar en Español de este Manual del propietario, visite www.heatnglo.com.

Pour demander un exemplaire en français de ce Manuel du propriétaire, visitez www.heatnglo.com.

Owner’s Manual

Installation and Operation

Models:

SL-550TV-IPI-E

SL-750TV-IPI-E

SL-950TV-IPI-E

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

• Leave this manual with

and maintenance

these instructions for safe

party responsible for use

instructions included.

installation and operation.

and operation.

DO DISCARDNOT

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.

DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

What to do if you smell gas

-DO NOT try to light any appliance.

-DO NOT touch any electrical switch.DO NOT use any phone in your building.

-Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter.

A CO detector shall be installed in the room where the appliance in installed.

Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory trained professionals, or technicians supervised by an NFI certified professional.

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

1

NATURAL GAS

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

A. Congratulations

Congratulations on selecting a Heat & Glo gas fireplace, an elegant and clean alternative to wood burning fireplaces. The Heat & Glo gas fireplace you have selected is designed to provide the utmost in safety, reliability, and efficiency.

As the owner of a new fireplace, you’ll want to read and carefully follow all of the instructions contained in this owner’s manual. Pay special attention to all cautions and warnings.

This owner’s manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this owner’s manual, unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo gas fireplace will give you years of durable use and trouble-freeenjoyment. Welcome to the Heat & Glo family of fireplace products!

Homeowner Reference Information

We recommend that you record the following pertinent information about your fireplace.

Model Name: ___________________________________________ Date purchased/installed:__________________

Serial Number:__________________________________________ Location on fireplace: _____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

Listing Label Information/Location The model information regarding your specific fireplace can be found on the rating plate usually located in the control area of the fireplace.

Type of Gas

Gas and Electric

Information

This product may be covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevets suivants): (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending (ou autres brevets americains et etrangers en attente).

Heat & Glo, a brand of Hearth & Home Technologies, Inc. 7571 215th Street West, Lakeville, MN 55044

Not for use with solid fuel.

(Ne doit pas entre utilise avec un combustible solide).

Type of Gas(Sorte De Gaz): This appliance must be installed in accordance with local codes, ifany; if not, follow ANSI Z223.1in the USAor CAN/CGA B149 installation codes.(Installer l’appareil selon les codes ou reglements locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)

ANSI Z21XX-XXXX· CSA2.XX-MXX· UL307B

Minimum Permissible Gas Supply for Purposes of Input Adjustment.

 

 

 

Approved Minimum(De Gaz) Acceptable

0.0in w.c.

(Po.Col. d’eau)

 

 

 

Maximum Pressure (Pression)

 

0.0 in w.c.

(Po.Col. d’eau)

 

 

 

Maximum Manifold Pressure(Pression)

0.0 in w.c.

(Po.Col. d’eau)

 

 

 

Minimum Manifold Pressure(Pression)

0.0 in w.c.

(Po.Col. d’eau)

 

 

 

Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes

MADE IN USA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN CANADA

 

Model:

XXXXXXXX

 

ALTITUDE:

0-0000FT.

0000-0000FT.

 

(Modele):

 

MAX. INPUT BTUH:

00,000

00,000

 

 

 

 

 

 

 

MIN. INPUT BTUH:

00,000

00,000

 

Serial

XXXXXXXX

 

ORIFICE SIZE:

#XXXXX

#XXXXX

 

 

 

(Serie):

 

Model Number

Serial Number

2

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

Safety Alert Key:

DANGER! Indicates a hazardous situation which, if not avoidedwill result in death or serious injury.

WARNING! Indicates a hazardous situation which, if not avoidedcould result in death or serious injury.

CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE: Used to address practices not related to personal injury.

Table of Contents

A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

B. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . 5

1 Listing and Code Approvals

A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

B. Tempered Glass Specifications . . . . . . . . . . . . . . . . . . . . . 7

C. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 8

E. Non-CombustibleMaterials Specification. . . . . . . . . . . . . . 8

F. Combustible Materials Specification . . . . . . . . . . . . . . . . . 8

G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

User Guide

2 Operating Instructions

A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 C. Fan Kit (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 D. Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 E. Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . 10 F. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 G. Remote Controls, Wall Controls and Wall Switches. . . . . 10 H. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 10 I. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 11 J. After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 K. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 12

3 Maintenance and Service

A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . .13

B. Maintenance Tasks-QualifiedService Technician . . . . . . 14

Installer Guide

4 Getting Started

A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 16

B. Design and Installation Considerations . . . . . . . . . . . . . . 17

C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 17

D. Inspect Appliance and Components. . . . . . . . . . . . . . . . . 17

E. Negative Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5 Framing and Clearances

A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . 19

B. Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . 20

C. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

D. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 21

6 Termination Locations

A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 22

7 Vent Information and Diagrams

A. Vent Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

B. Vent System Configuration. . . . . . . . . . . . . . . . . . . . . . . . 23

8 Vent Clearances and Framing

A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 24 B. Wall and Ceiling Penetration Framing . . . . . . . . . . . . . . . 24 C. Vertical Penetration Framing . . . . . . . . . . . . . . . . . . . . . . 24

9 Appliance Preparation

A. Installing Outside Air Kit Damper Assembly . . . . . . . . . . . 25 B. Gas and Electrical Connections . . . . . . . . . . . . . . . . . . . . 25 C. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 25

10 Installing Vent Pipe

A. Assembly of Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . 26 B. Attaching Vent to Firebox . . . . . . . . . . . . . . . . . . . . . . . . . 26 C. Securing Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 26 D. Install Attic Insulation Shield. . . . . . . . . . . . . . . . . . . . . . . 26

11 Gas Information

A. Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

B. Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . 27

12 Electrical Information

A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 B. Intellifire Ignition System Wiring . . . . . . . . . . . . . . . . . . . . 28 C. Optional Accessories Requirements . . . . . . . . . . . . . . . . 28 D. Electrical Service and Repair . . . . . . . . . . . . . . . . . . . . . . 28 E. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 30 F. Wall Switch Installation for Fan (Optional) . . . . . . . . . . . . 30

13 Finishing

A. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 31

B. Facing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

3

14 Appliance Setup

A. Remove Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 33 B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 33 C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 E. Lava Rock, Mineral Wool/Ember Placement . . . . . . . . . . 33 F. Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . 34 G. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 H. Install the Mesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 I. Install Trim and/or Surround. . . . . . . . . . . . . . . . . . . . . . . 36 J. Install Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 K. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

15 Troubleshooting

A. Intellifire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 37

16 Reference Materials

A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . . 39

B. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

C. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Î = Contains updated information.

4

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

B. Limited Lifetime Warranty

Heat & Glo • SL-550 /750 /950TV-IPI-E

2119-900Rev. J • 12/09

5

B. Limited Lifetime Warranty (continued)

6

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

1 Listing and Code Approvals

A. Appliance Certification

MODELS: SL-550TV-IPI-E,SL-750TV-IPI-E,SL-950TV-IPI-E

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: B-VentGas Appliance

STANDARD: ANSIZ21.50-2007• CSA2.22-2007

This product is listed to ANSI standards for “Vented Gas Fireplaces” and “Gas Fired Appliances for Use at High Altitudes”.

May be installed in a sleeping room when the provisions for combustion, ventilation and dilution air are met per the requirements of ANSI 223.1/NFPA 54 National Fuel Gas Code. In Canada, installation in a sleeping room requires installation with a thermostat certified for use with this product. Consult your local authorities having jurisdiction.

NOTICE: This installation must conform with local codes. In the absence of local codes you must comply with the National Fuel Gas Code, ANSIZ223.1-latestedition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.

This model (natural gas and propane) can be installed in a bedroom (in Canada) if a thermostat (Model WH-STAT)is installed with the unit. Consult local code authorities. Detailed installation instructions for ModelWH-STATare included with the kit.

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

B. Tempered Glass Specifications

Hearth & Home Technologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the Consumer Product Safety Commission (CPSC). The tempered glass has been tested and certified to the requirements of ANSI Z97.1 andCPSC 16 CFR 1202 (Safety Glazing Certification CouncilSGCC# 1595 and1597. Architectural Testing, Inc. Reports02-31919.01 and02-31917.01).

This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements” which refers to15 U.S. Code(USC) 2063 stating “…Such certificate shall accompany the product or shall otherwise be furnished to any distributor or retailer to whom the product is delivered.”

Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory. Please contact your dealer or distributor to order.

C. BTU Specifications

Model(s)

Maximum

Minimum

Orifice

U.S. (0-2000ft.) or Canada(2000-4500ft.)

Input BTU/h

Input BTU/h

Size

(DMS)

SL-550TV-IPI-E

US

21,100

14,700

44

 

 

 

 

CAN

18,990

13,230

45

 

 

 

 

 

 

SL-550TV-IPI-E(LP)

US

20,000

14,300

55

 

 

 

 

CAN

18,000

12,870

56

 

 

 

 

 

 

SL-750TV-IPI-E

US

24,800

17,700

42

 

 

 

 

CAN

22,320

15,930

43

 

 

 

 

 

 

SL-750TV-IPI-E(LP)

US

23,200

17,300

54

 

 

 

 

CAN

20,880

15,570

55

 

 

 

 

 

 

SL-950TV-IPI-E

US

30,900

21,300

37

 

 

 

 

CAN

27,810

19,170

38

 

 

 

 

 

 

SL-950TV-IPI-E(LP)

US

30,700

22,500

52

 

 

 

 

CAN

27,630

20,250

53

 

 

 

 

 

 

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

7

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

In the USA: Reduce input rate 4% for each 1000 feet above 2000 feet.

In CANADA: Reduce input rate 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

Check with your local gas utility to determine proper orifice size.

E. Non-CombustibleMaterials Specification

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 ºC and UL763shall be considered non-combustible materials.

F. Combustible Materials Specification

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite and burn, whether flame proofed or not, or plastered or unplastered shall be considered combustible materials.

G. Electrical Codes

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric Code CSA

C22.1.

A 110-120VAC circuit for this product must be protected withground-faultcircuit-interrupterprotection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

8

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

2 Operating InstructionsUser Guide

A. Gas Fireplace Safety

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

If you expect that small children or vulnerable adults may come into contact with this fireplace, the following precautions are recommended:

Install a physical barrier such as:

-A decorative firescreen.

-Adjustable safety gate.

Install a switch lock or a wall/remote control with child protection lockout feature.

Keep remote controls out of reach of children.

Never leave children alone near a hot fireplace, whether operating or cooling down.

Teach children to NEVER touch the fireplace.

Consider not using the fireplace when children will be present.

Contact your dealer for more information, or visit: www. hpba.org/staysafe.

To prevent unintended operation when not using your fireplace for an extended period of time (summer months, vacation, trips, etc):

Remove batteries from remote controls.

Turn off wall controls.

Unplug 3 volt adapter plug and remove batteries on IPI models.

B. Your Fireplace

WARNING! DO NOT operate fireplace before reading and understanding operating instructions. Failure to operate fireplace according to operating instructions could cause fire or injury.

DECORATIVE DOORS

(NOT SHOWN)

SECTION 2.E.

FIXED GLASS ASSEMBLY

(NOT SHOWN)

SECTION 14.G.

OUTSIDE AIR CONTROL

(NOT SHOWN)

SECTION 9.A.

MANTEL

HEARTH

CLEAR SPACE

SECTION 2.D.

Figure 2.1 General Operating Parts

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

9

C. Fan Kit (optional)

• Refer to Figures 2.2 and 2.3 for location of control.

RHEOSTAT

TEMPERATURE

SWITCH

 

SENSOR

Figure 2.2 Fan Wiring with Rheostat

 

VARIABLE

 

SPEED SWITCH

JUNCTION BOX

 

TEMPERATURE

 

SENSOR SWITCH

 

BLUE

 

Figure 2.3 Detail of Fan Wiring with Rheostat

E. Decorative Doors and Fronts

WARNING! Risk of Fire! Install ONLY doors or fronts approved by Hearth & Home Technologies. Unapproved doors or fronts may cause fireplace to overheat.

This fireplace has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the fireplace with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

For more information refer to the instructions supplied with your decorative door or front.

F. Fixed Glass Assembly

See Section 14.G.

G.Remote Controls, Wall Controls and Wall Switches

Follow the instructions supplied with the control installed to operate your fireplace:

For safety:

Install a switch lock or a wall/remote control with child protection lockout feature.

Keep remote controls out of reach of children.

See your dealer if you have questions.

D. Clear Space

WARNING! DO NOT place combustible objects in front of the fireplace or block louvers. High temperatures may start a fire. See Figure 2.4.

Avoid placing candles and other heat-sensitiveobjects on mantel or hearth. Heat may damage these objects.

H. Before Lighting Fireplace

Before operating this fireplace for the first time, have a qualified service technician:

Verify all shipping materials have been removed from inside and/or underneath the firebox.

 

 

 

 

• Review proper placement of logs, ember material and/or

 

 

 

 

 

other decorative materials.

 

 

 

 

Check the wiring.

 

 

 

 

Check the air shutter adjustment.

 

 

 

 

Ensure that there are no gas leaks.

 

 

 

 

• Ensure that the glass is sealed and in the proper position

 

 

 

 

 

and that the integral barrier is in place.

 

 

 

 

WARNING! Risk of Fire/Asphyxiation! DO NOT oper-

 

 

 

 

ate fireplace with fixed glass assembly removed.

3

FT.

 

 

 

 

 

 

 

 

 

 

IN CLEAR

 

 

 

 

 

FRONT OFSPACE

 

 

 

 

 

FIREPLACE

 

 

 

 

Figure 2.4 Clear Space

 

 

 

 

10

 

Heat & Glo

SL-550 /750 /950TV-IPI-E

2119-900Rev. J • 12/09

Î I. Lighting Instructions (IPI)

The IPI system may be operated with two D-cellbatteries. When using batteries, unplug the transformer. To prolong battery life, remove them when using the transformer.

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance is equipped with an intermittent pilot ignition (IPI) device which automatically lights the burner. DO NOT try to light the burner by hand.

B.BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

DO NOT try to light any appliance.

DO NOT touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

C.DO NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

WARNING: CAUTION:

DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240 VAC) TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause cancer, birth defects, or other reproductive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline and other liquids having flammable vapors away.

DO NOT operate the appliance with fixed glass assembly removed, cracked or broken. Replacement of the fixed glass assembly should be done by a licensed or qualified service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certified for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional information, consult a qualified installer, service agency or the gas supplier.

For additional information on operating your

Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.

LIGHTING

INSTRUCTIONS (IPI)

1.This appliance is equipped with an ignition device which automatically lights the burner. DO NOT try to light the burner by hand.

GAS

VALVE

2.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the Safety Information located on the left side of this label. If you do not smell gas, go to next step.

3.To light the burner:

Equipped with wall switch: Turn ON/OFF switch to ON.

Equipped with remote or wall control: Press ON or FLAME button.

Equipped with thermostat: Set temperature to desired setting.

4.If the appliance does not light after three tries, call your service technician or gas supplier.

TO TURN OFFGAS TO APPLIANCE

1.Equipped with wall switch: Turn ON/OFF switch to OFF.

Equipped with remote or wall control: Press OFF button.

Equipped with thermostat: Set temperature to lowest setting.

2.Service technician should turn off electric power to the control when performing service.

593-913G

Final inspection by

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

11

J. After Fireplace is Lit

Initial Break-inProcedure

The fireplace should be run three to four hours continuously on high.

Turn the fireplace off and allow it to completely cool.

Remove fixed glass assembly. See Section 14.G.

Clean fixed glass assembly. See Section 3.

Replace the fixed glass assembly and run continuously on high an additional 12 hours.

This cures the materials used to manufacture the fireplace.

NOTICE! Open windows for air circulation during fireplace break-in.

Some people may be sensitive to smoke and odors.

Smoke detectors may activate.

K.Frequently Asked Questions

 

ISSUE

SOLUTIONS

 

Condensation on the glass

This is a result of gas combustion and temperature variations. As the appliance warms, this

 

condensation will disappear.

 

 

 

Blue flames

This is a result of normal operation and the flames will begin to yellow as the appliance is al-

 

lowed to burn for 20 to 40 minutes.

 

 

 

 

When first operated, this appliance may release an odor for the first several hours. This is caused

 

Odor from appliance

by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may

 

 

also be released from finishing materials and adhesives used around the appliance.

 

 

This is a normal result of the curing process of the paint and logs. Glass should be cleaned

 

Film on the glass

within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing

 

process. A non-abrasivecleaner such as gas fireplace glass cleaner may be necessary. See

 

 

 

 

your dealer.

 

 

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to

 

Metallic noise

the sound produced by a furnace or heating duct. This noise does not affect the operation or

 

 

longevity of the appliance.

 

 

 

Î

Is it normal to see the pilot flame burn

In an intermittent pilot ignition system (IPI), the pilot flame should turn off when appliance is

turned off. Some optional control systems available with IPI models may allow pilot flame to

 

continually?

remain lit.

 

 

 

 

 

12

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

3 Maintenance and Service

Any safety screen or guard removed for servicing must be replaced prior to operating the fireplace.

When properly maintained, your fireplace will give you many years of trouble-freeservice. We recommend annual service by a qualified service technician.

Doors, Surrounds, Fronts

Frequency: Annually

By: Homeowner

Tools needed: Protective gloves, stable work surface

• Assess condition of screen and replace as necessary.

A. Maintenance Tasks-Homeowner

Installation and repair should be done by a qualified service technician only. The fireplace should be inspected before use and at least annually by a professional service person.

The following tasks may be performed annually by the homeowner. If you are uncomfortable performing any of the listed tasks, please call your dealer for a service appointment.

More frequent cleaning may be required due to lint from carpeting or other factors. Control compartment, burner and circulating air passageway of the fireplace must be kept clean.

CAUTION! Risk of Burns! The fireplace should be turned off and cooled before servicing.

Glass Cleaning

Frequency: Seasonally

By: Homeowner

Tools Needed: Protective gloves, glass cleaner, drop cloth and a stable work surface.

CAUTION! Handle fixed glass assembly with care.

Glass is breakable.

Avoid striking, scratching or slamming glass

Avoid abrasive cleaners

DO NOT clean glass while it is hot

Prepare a work area large enough to accommodate fixed glass assembly and door frame by placing a drop cloth on a flat, stable surface.

Note: Fixed glass assembly and gasketing may have residue that can stain carpeting or floor surfaces.

Remove door or decorative front from fireplace and set aside on work surface.

See Section 14.G for instructions to remove fixed glass assembly.

Clean glass with a non-abrasivecommercially available cleaner.

-Light deposits: Use a soft cloth with soap and water

-Heavy deposits: Use commercial fireplace glass cleaner (consult with your dealer)

Carefully set fixed glass assembly in place on fireplace. Hold glass in place with one hand and secure glass latches with the other hand.

Reinstall door or decorative front.

Inspect for scratches, dents or other damage and repair as necessary.

Check that louvers are not blocked.

Vacuum and dust surfaces.

Remote Control

Frequency: Seasonally

By: Homeowner

Tools needed: Replacement batteries and remote control instructions.

Locate remote control transmitter and receiver.

Verify operation of remote. Refer to remote control operation instructions for proper calibration and setup procedure.

Place batteries as needed in remote transmitters and battery-poweredreceivers.

Place remote control out of reach of children.

If not using your fireplace for an extended period of time (summer months, vacations/trips, etc), to prevent unintended operation:

Remove batteries from remote controls.

Unplug 3 volt adapter plug on IPI models.

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

13

Venting

Frequency: Seasonally

By: Homeowner

Tools needed: Protective gloves and safety glasses.

Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc.

Verify termination cap clearance to subsequent construction. See Section 6.

Inspect for corrosion or separation.

Verify weather stripping, sealing and flashing remains intact.

Inspect draft shield to verify it is not damaged or missing.

B.Maintenance Tasks-QualifiedService Technician

The following tasks must be performed by a qualified service technician.

Gasket Seal and Glass Assembly Inspection

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, drop cloth and a stable work surface.

Inspect gasket seal and its condition.

Inspect fixed glass assembly for scratches and nicks that can lead to breakage when exposed to heat.

Confirm there is no damage to glass or glass frame. Replace as necessary.

Verify that fixed glass assembly is properly retained and attachment components are intact and not damaged. Replace as necessary.

Logs

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves.

Inspect for damaged or missing logs. Replace as necessary. Refer to Section 14 for log placement instructions.

Verify correct log placement and no flame impingement causing sooting. Correct as necessary.

Firebox

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, sandpaper, steel wool, cloths, mineral spirits, primer andtouch-uppaint.

Inspect for paint condition, warped surfaces, corrosion or perforation. Sand and repaint as necessary.

Replace fireplace if firebox has been perforated.

Control Compartment and Firebox Top

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, vacuum cleaner, dust cloths

Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw tips that have penetrated the sheet metal are sharp and should be avoided.

Remove all foreign objects.

Verify unobstructed air circulation.

Burner Ignition and Operation

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, vacuum cleaner, whisk broom, flashlight, voltmeter, indexed drill bit set, and a manometer.

Verify burner is properly secured and aligned with pilot or igniter.

Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.

Replace Glowing embers with new dime-sizepieces.DO NOT block ports or obstruct lighting paths. Refer to Section 14 for proper ember placement.

Verify batteries have been removed from battery backup IPI systems to prevent premature battery failure or leaking.

Check for smooth lighting and ignition carryover to all ports. Verify that there is no ignition delay.

Inspect for lifting or other flame problems.

Verify air shutter setting is correct. See Section 14 for required air shutter setting. Verify air shutter is clear of dust and debris.

Inspect orifice for soot, dirt and corrosion. Verify orifice size is correct. See Service Parts List for proper orifice sizing.

Verify manifold and inlet pressures. Adjust regulator as required.

Inspect pilot flame pattern and strength. See Figure 3.1 for proper pilot flame pattern. Clean or replace orifice spud as necessary.

Inspect

14

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

Figure 3.1 IPI Pilot Flame Patterns

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

15

4

Getting Started

Installer Guide

 

 

 

A. Typical Appliance System

NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual

NON-COMBUSTIBLEROOF FLASHING MAINTAINS MINIMUM CLEARANCE AROUND PIPE

VENT PIPE (SECTIONS 7 and 8)

CEILING FIRESTOP ON FLOOR OF ATTIC (SECTION 8.B)

FRAMING/HEADER (SECTION 5)

VERTICAL TERMINATION CAP (SECTION 4.D)

STORM COLLAR (SECTION 4.D)

VENT PIPE PENETRATES ROOF

PREFERABLY WITHOUT AFFECTING

ROOF RAFTERS (SECTION 8.B)

ATTIC INSULATION SHIELD (NOT SHOWN) MUST BE USED HERE TO KEEP INSULATION AWAY

FROM VENT PIPE IF ATTIC IS INSULATED (SECTION 10.D)

FRAMING HEADED OFF IN CEILING JOISTS (SECTION 8.B)

OPTIONAL

WALL SWITCH

MANTEL AND MANTEL LEG (SECTION 5.D)

SURROUND

HEARTH EXTENSION

GAS LINE (SECTION 11)

Figure 4.1 Typical System

16

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

B. Design and Installation Considerations

Heat & Glo B-typevent gas appliances are designed to operate with all exhaust gases expelled to the outside of the building, and combustion air pulled from the room.

Installation MUST comply with local, regional, state and national codes and regulations. Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction over restrictions, installation inspection and permits.

Before installing, determine the following:

Where the appliance is to be installed.

The vent system configuration to be used.

Gas supply piping requirements.

Electrical wiring requirements.

Framing and finishing details.

Whether optional accessories—devicessuch as a fan, wall switch, or remotecontrol—aredesired.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualified service technician, service agency or your dealer.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Tape measure

Framing material

Pliers

High temperature caulking material

Hammer

Phillips screwdriver

Gloves

Framing square

Voltmeter

Electric drill and bits (1/4 in.)

Plumb line

Safety glasses

Level

Reciprocating saw

Manometer

Flat blade screwdriver

Noncorrosive leak check solution

1/2 - 3/4 in. length, #6 or #8 Self-drillingscrews One 1/4 in. female connection (for optional fan).

D. Inspect Appliance and Components

The following B-ventcomponents are needed for installation.

Fireplace Box

Pipe Components

Firestops

Attic Insulation Shield

Elbows

Strapping

Roof Flashing or Chase Top

Termination Cap

Storm Collar

Carefully remove the appliance and components from the packaging.

The vent system components and decorative doors and fronts may be shipped in separate packages.

If packaged separately, the log set and appliance grate must be installed.

Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

Installation and use of any damaged appliance or vent system component.

Modification of the appliance or vent system.

Installation other than as instructed by Hearth & Home Technologies.

Improper positioning of the gas logs or the glass door.

Installation and/or use of any component part not approved by Hearth & Home Technologies.

Any such action may cause a fire hazard.

WARNING! Risk of Fire, Explosion or Electric Shock!

DO NOT use this appliance if any part has been under water. Call a qualified service technician to inspect the appliance and to replace any part of the control system and/or gas control which has been under water.

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

17

E. Negative Pressure

WARNING! Risk of Asphyxiation! Negative pressure can cause spillage of combustion fumes and soot. Fireplace needs to draft properly for safety.

Draft is the pressure difference needed to vent fireplaces successfully. Considerations for successful draft include:

Preventing negative pressure

Location of fireplace and chimney

Negative pressure results from the imbalance of air available for the fireplace to operate properly. Causes for this imbalance include:

Exhaust fans (kitchen, bath, etc.)

Range hoods

Combustion air requirements for furnaces, water heaters and other combustion appliances

Clothes dryers

Location of return-airto furnace or air conditioning

Imbalances of the HVAC air handling system

Upper level air leaks (recessed lighting, attic hatch opening, duct leaks)

To minimize the effects of negative air pressure, the following must be considered:

Install the fresh air kit. Install the intake on the side of the house towards prevailing winds during the heating season.

Ensure adequate outdoor air is supplied for combustion appliances and exhaust equipment.

Ensure furnace and air conditioning return vents are not located in the immediate vicinity of the fireplace.

Avoid installing the fireplace near doors, walkways or small isolated spaces.

Recessed lighting should be of “sealed can” design; attic hatches weather stripped or sealed; and attic mounted ductwork and air handler joints and seams taped or sealed.

Basement installations should be avoided due to stack effect. Stack effect creates negative pressure in lower levels. Hearth & Home Technologies recommends the use of direct vent fireplaces in basements.

Location of the fireplace and chimney will affect performance. As shown in Figure 4.2, the chimney should:

Be installed through the warm space enclosed by the building envelope. This helps to produce more draft, especially during lighting and die-downof the fire.

Penetrate the highest part of the roof. This minimizes the effects of wind turbulence.

Be located away from trees, adjacent structures, uneven roof lines and other obstructions.

Offsets can restrict draft so their use should be minimized. Consider the fireplace location relative to floor and ceiling and attic joists.

Recommended Recommended

Location Location

Marginal

Location

Location

Not

Recommended

Location NOT

Recommended

Windward

Leeward

Multi-levelRoofs

Figure 4.2

18

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

5 Framing and Clearances

A. Selecting Appliance Location

When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1).

WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.

Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

NOTICE: Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY. Illustrations/diagrams are not drawn to scale. Actual installation may vary due to individual design preference.

F A

TOP VENT

B

ALCOVE D

INSTALLATION

A

B

C

TOP VENT

TOP VENT

B

E

Model

A

B

C

D

E

F

Minimum

 

 

 

 

 

 

 

SL-550TV-IPI-E

Inches

42

37

59-1/2

 

16-1/4

1/2

 

 

 

 

 

 

 

Millimeters

1067

940

1511

 

413

13

 

 

 

 

 

 

 

 

 

 

 

Inches

45-1/2

42

64-3/8

See Section

16-1/4

1/2

SL-750TV-IPI-E

 

 

 

 

5.D for Alcove

 

 

 

 

 

 

 

 

 

Millimeters

1156

1067

1635

Installation

413

13

 

 

 

 

 

 

 

 

SL-950TV-IPI-E

Inches

50-1/2

49

71-1/2

 

16-1/4

1/2

 

 

 

 

 

 

 

Millimeters

1283

1245

1816

 

413

13

 

 

 

 

 

 

 

 

 

 

Figure 5.1 Appliance Locations

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

19

B. Constructing the Appliance Chase

A chase is a vertical box-likestructure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should be enclosed inside the chase.

NOTICE: Treatment of ceiling firestops and wall shield firestops and construction of the chase may vary with the type of building. These instructions are not substitutes for the requirements of local building codes. Therefore, you MUST check local building codes to determine the requirements to these steps.

Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building envelope in any manner.

Walls, ceiling, base plate and cantilever floor of the chase should be insulated. Vapor and air infiltration barriers should be installed in the chase as per regional codes for the rest of the home. Additionally, in regions where cold air infiltration may be an issue, the inside surfaces may be sheetrocked and taped for maximum air tightness.

To further prevent drafts, the wall shield and ceiling firestops should be caulked with high temperature caulk to seal gaps. Gas line holes and other openings should be caulked with high temp caulk or stuffed with unfaced insulation. If the appliance is being installed on a cement slab, a layer of plywood may be placed underneath to prevent conducting cold up into the room.

C. Clearances

NOTICE: Install appliance on hard metal or wood surfaces extending full width and depth.DO NOT install directly on carpeting, vinyl, tile or any combustible material other than wood.

WARNING! Risk of Fire! Maintain specified air space clearances to appliance and vent pipe:

Insulation and other materials must be secured to prevent accidental contact.

The chase must be properly blocked to prevent blown insulation or other combustibles from entering and making contact with fireplace or chimney.

Failure to maintain airspace may cause overheating and a fire.

A

E

 

 

 

 

 

 

F

 

J

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B

 

 

 

 

 

 

 

 

H

 

 

 

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

D

 

 

 

 

 

 

G

 

 

 

 

 

 

 

 

 

 

 

 

 

I

 

 

 

 

 

* MINIMUM FRAMING DIMENSIONS

 

 

 

 

 

 

A

B

C

D

E

F

G

H

I

J

Models

 

Rough

Rough

Rough

Rough

Clearance

Combustible

Combustible

Behind

Sides of

Front of

 

 

Opening

Opening

Opening

Opening

 

 

(Vent Pipe)

(Height)

(Depth)

(Width)

to Ceiling

Floor

Flooring

Appliance

Appliance

Appliance

 

 

 

 

 

 

 

 

SL-550TV-IPI-E

in.

10

34-3/4

16-1/4

37

32

0

0

1/2

1/2

36

mm

254

883

413

940

813

0

0

13

13

915

SL-750TV-IPI-E

in.

10

38-1/4

16-1/4

42

32

0

0

1/2

1/2

36

mm

254

971

413

1067

813

0

0

13

13

915

SL-950TV-IPI-E

in.

10

42-1/4

16-1/4

49

32

0

0

1/2

1/2

36

mm

254

1073

413

1245

813

0

0

13

13

915

* Adjust framing dimensions for interior sheathing (such as sheetrock)

Figure 5.2 Clearances to Combustibles

20

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

D. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing or finishing material closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).

Combustible Mantels

 

 

 

 

 

 

 

 

 

 

 

 

CEILING

 

 

 

 

 

12

 

 

 

 

 

 

 

 

 

 

 

 

10

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

8

9

 

 

 

 

 

 

 

 

 

 

32

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12 13

 

4

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

10 11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

 

 

 

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TOP OF HOOD OR FIREPLACE OPENING

Note: All measurements are in inches.

Figure 5.3 Minimum Vertical and Maximum Horizontal

Dimensions of Combustibles

 

1/2 in.

3-1/2in.

SHEETROCK

NON-COMBUSTIBLE

BOARD SHIPPED

WITH APPLIANCE

1/2 in.

 

 

 

 

 

 

 

 

 

1/2 IN.

TOP VIEW

 

 

 

 

 

 

 

 

 

 

MINIMUM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2-7/8IN.

MINIMUM 3 FT. MAXIMUM

Note: Clearance from opening Alcove/Mantel leg.

Figure 5.5 Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening)

 

 

 

 

 

 

 

 

 

3 IN.

TOP VIEW

 

 

 

 

 

 

 

 

 

 

MINIMUM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5-3/8IN.

MINIMUM

UNLIMITED

Note: Clearance from opening Alcove/Mantel leg.

Figure 5.6 Clearance to Wall Projection (Acceptable on one side of opening.)

NON-COMBUSTIBLEZONE

Figure 5.4 Non-CombustibleZone

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

21

6 Termination Locations

A. Vent Termination Minimum Clearances

WARNING

Fire Risk.

Maintain vent clearance to combustibles as specified.

DO NOT pack air space with insulation or other materials.

Failure to keep insulation or other materials away from vent pipe may cause overheating and fire.

LISTED B-VENTTERMINATION CAP

8 FEET

VERTICAL

 

WALL

LOWEST

DISCHARGE

OPENING

X

12

ROOF PITCH

IS X/ 12

H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING

Roof Pitch

H (Min.) Ft.

Flat to 6/12...........................................................

1.0*

Over 6/12 to 7/12.................................................

1.25*

Over 7/12 to 8/12.................................................

1.5*

Over 8/12 to 9/12.................................................

2.0*

Over 9/12 to 10/12...............................................

2.5

Over 10/12 to 11/12 .............................................

3.25

Over 11/12 to 12/12 .............................................

4.0

Over 12/12 to 14/12.............................................

5.0

Over 14/12 to 16/12.............................................

6.0

Over 16/12 to 18/12.............................................

7.0

Over 18/12 to 20/12.............................................

7.5

Over 20/12 to 21/12.............................................

8.0

* 3 foot minimum in snow regions

Figure 6.1 Minimum Height From Roof To Lowest Discharge Opening

A

B

6 in. (minimum) up to 20 in.

18 in. minimum

152 mm/508 mm

457 mm

20 in. and over

0 in. minimum

Gas, Wood or Fuel Oil

Termination Cap

B

A*

Gas

Termination

Cap **

*If using decorative cap cover(s), this distance may need to be increased. Refer to the installation instructions supplied with the decorative cap cover.

**In a staggered installation with both gas and wood terminations, the wood termination cap must be higher than the gas termination cap.

Figure 6.2 Staggered Termination Caps

Î

22

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

7 Vent Information and Diagrams

A. Vent Guidelines

WARNING! Risk of Fire and Asphyxiation!This appliance requires the specified pipe for operation. Incorrect pipe may cause spillage, condensation and overheating.

These models require the following size B-ventdouble wall, or single wall rigid or flex vent pipe.

Models

Pipe Size

SL-550TV-IPI-E

5 inch

SL-750TV-IPI-E

5 inch

SL-950TV-IPI-E

6 inch

Follow pipe manufacturer’s installation guidelines when installing the appliance.

WARNING! Risk of Fire, Explosion or Asphyxiation!

DO NOT connect this gas appliance to a chimney flue serving a separate solid-fuelor gas burning appliance.

Vent this appliance directly outside.

Use separate vent system for this appliance.

May impair safe operation of this appliance or other appliances connected to the flue.

B. Vent System Configuration

CAUTION! Risk of Fire! ALL vent configuration specifications MUST be followed. This product is tested and listed to these specifications. Appliance performance will suffer if specifications are not followed.

Rise to Run Ratio = 2:1

Maximum Total Horizontal Run = 15 Feet Minimum Total Vertical Rise = 9 Feet Maximum Total Vertical Rise = 48 Feet

Maximum Number of Elbows: Two 90º or Four 45º

WARNING! Risk of Fire or Explosion! Insulation and other combustibles must not infringe on clearances.

ALWAYS maintain specified clearances around venting and firestop systems.

Install firestops as specified.

Failure to keep insulation or other material away from vent pipe may cause fire.

 

MINIMUM CLEARANCES

 

ARE PER VENT

 

MANUFACTURER’S

 

SPECIFICATIONS

 

METAL

9 FEET

PLUMBER’S

STRAP

MINIMUM

 

48 FEET

 

MAXIMUM

 

 

VENT SUPPORTS ARE PER

 

VENT MANUFACTURER’S

 

SPECIFICATIONS

Figure 7.1

Note: Horizontal runs require

 

1/4 in. rise per foot run.

 

VENT SUPPORTS

 

ARE PER VENT

METAL

MANUFACTURER'S

SPECIFICATIONS.

PLUMBERS' STRAP

MAXIMUM HORIZONTAL RUN IS 50%

OF VERTICAL. HORIZONTAL RUN

CANNOT BE MORE THAN 15 FT.

Figure 7.2

 

 

MAXIMUM

 

HORIZONTAL

 

15 FEET

MINIMUM VERTICAL 9 FEET

45DEGREES ELBOW

90DEGREES ELBOW

Figure 7.3

OFFSETS EXCEEDING 45 DEGREES ADAPT HORIZONTAL LIMITATIONS

Note: Maximum horizontal distance is 50% vertical vent height.

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

23

8 Vent Clearances and Framing

A. Pipe Clearances to Combustibles

Vent clearances are per vent manufacturer’s specifications. MUST be Listed B-Ventpipe.

WARNING! Risk of Fire! Maintain air space clearance to vent.DO NOT pack insulation or other combustibles:

Between ceiling firestops

Between wall shield firestops

Around vent system

Failure to keep insulation or other material away from vent pipe may cause over heating and fire.

B. Wall and Ceiling Penetration Framing

For a wall or ceiling penetration consult B-ventpipe manufacturer’s instructions to provide adequate clearances. Use same size framing materials as those used in the wall or ceiling construction. Firestop spacers must be used in wall and ceiling penetrations per theB-Ventpipe manufacturer’s specifications and national, regional and local codes.

Note: MUST terminate vertically.

1 in. TOP

CLEARANCE

1 in. CLEARANCE

AROUND VERTICAL

SECTIONS

1 in. SIDE AND

BOTTOM CLEARANCE

Figure 8.1 Pipe Clearances

C. Vertical Penetration Framing

WARNING! Risk of Fire! DO NOT allow loose materials or insulation to touch vent. Hearth & Home Technologies Inc. requires the use of an attic shield.

The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constructed of 26 gauge minimum metal that extends at least 2 in. (51 mm) above insulation.

Attic shields must meet specified clearance and be secured in place.

Use B-ventmanufacturer’s firestops to provide adequate clearances.

24

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

9 Appliance Preparation

A.Installing Outside Air Kit Damper Assembly

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

WARNING! Risk of Fire/Asphyxiation. DO NOT draw outside combustion air from:

Wall, floor or ceiling cavity.

Enclosed space such as an attic or garage.

Close proximity to exhaust vents or chimneys. Fumes or odor may result.

Remove and discard cover plate or knockout from side of appliance.

Open air kit damper slightly.

Locate door hinge toward back of appliance (see Figure 9.1).

DOOR

HINGE

HANDLE

Figure 9.1 Damper Assembly and Handle

Attach damper assembly to appliance using screws provided (see Figure 9.2).

Insert narrow end of handle through tab and into upper slot of door.

Check handle operation. Pull handle out to open, and in to close.

Figure 9.2

Outside Air Kit Installation

B. Gas and Electrical Connections

If applicable, ensure that gas and electrical connections are installed at this time. Refer to Sections 11 (Gas Information) and 12 (Electrical Information).

C. Securing and Leveling the Appliance

WARNING! Risk of Fire! Prevent contact with:

Sagging or loose insulation

Insulation backing or plastic

Framing and other combustible materials

Block openings into the chase to prevent entry of blownin insulation. Make sure insulation and other materials are secured.

DO NOT notch the framing around the appliance standoffs.

Failure to maintain air space clearance may cause overheating and fire.

The diagram shows how to properly position, level, and secure the appliance (see Figure 9.3). Nailing tabs are provided to secure the appliance to the framing members.

Bend out nailing tabs on each side.

Place the appliance into position.

Keep nailing tabs flush with the framing.

Level the appliance from side to side and front to back.

Shim the appliance as necessary. It is acceptable to use wood shims underneath the appliance.

Secure the appliance to the framing by using nails or screws through the nailing tabs.

Secure the appliance to the floor by inserting two screws through the pilot holes at the bottom of the appliance.

NAILING TABS

BOTH SIDES

Figure 9.3 Proper Positioning, Leveling And Securing Of An

Appliance

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

25

10 Installing Vent Pipe

A. Assembly of Vent Sections

This B-Ventappliance requires5-inch(SL-550/750TV-IPI-E) or6-inch(SL-950TV-IPI-E)B-ventdouble-wallpipe. Follow the pipe manufacturer’s installation guidelines when installing the unit. This will ensure proper operation and prevent safety hazards.

WARNING! Risk of Fire or Exhaust Fumes! Assemble pipe sections per B-vent manufacturer’s instructions. Use support tabs for screws. Pipe may separate if not properly joined.

C. Securing Vent Sections

Secure vent sections with vent supports following B-ventmanufacturer’s instructions.

WARNING! Risk of Fire or Explosion! Use vent run supports per vent manufacturer’s installation instructions.

Connect vent sections per vent manufacturer’s installation instructions.

Maintain all clearances to combustibles. Maintain specified slope (if required).

Improper support may allow vent to sag or separate.

B. Attaching Vent to Firebox

Attach the first B-Ventcomponent to the flue outlet collar using 2self-tappingscrews. Remove10-5/8in. collar for access to flue outlet collar.

CAUTION

The 10-5/8in. collar MUST be reattached. See Figure 10.1.

B-VENTCOMPONENT

SCREW

10-5/8IN. COLLAR

FLUE OUTLET COLLAR

D. Install Attic Insulation Shield

WARNING! Risk of Fire! DO NOT allow loose materials or insulation to touch vent. Hearth & Home Technologies Inc. requires the use of an attic shield.

The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constructed of 26 gauge minimum metal that extends at least 2 in. (51 mm) above insulation.

Attic shields must meet specified clearance and be secured in place.

Figure 10.1

26

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

11 Gas Information

A. Fuel Conversion

Make sure the appliance is compatible with available gas types.

Conversions must be made by a qualified service technician using Hearth & Home Technologies specified and approved parts.

B. Gas Pressure

Optimum appliance performance requires proper input pressures.

Gas line sizing requirements will be determined in ANSI Z223.1 National Fuel Gas Code in the USA and CAN/ CGA B149 in Canada.

Pressure requirements are:

Gas Pressure

Natural Gas

Propane

Minimum inlet pressure

5.0 in. w.c.

11.0 in. w.c.

Maximum inlet pressure

14.0 in. w.c.

14.0 in. w.c.

Manifold pressure

3.5 in. w.c.

10.0 in. w.c.

WARNING! Risk of Fire or Explosion! High pressure will damage valve. Low pressure may cause explosion.

Verify inlet pressures. Verify minimum pressures when other household gas appliances are operating.

Install regulator upstream of valve if line pressure is greater than 1/2 psig.

WARNING

Fire Risk. Explosion Hazard.

High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

Note: Have the gas supply line installed in accordance with local codes, if any. If not, follow ANSI 223.1. Installation should be done by a qualified installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter).

Note: A listed (and Commonwealth of Massachusetts approved) 1/2 in. (13 mm)T-handlemanualshut-offvalve and flexible gas connector are connected to the 1/2 in. (13 mm) control valve inlet.

If substituting for these components, please consult local codes for compliance.

C. Gas Connection

Refer to Reference Section 16 for location of gas line access in appliance.

Gas line may be run through knockout(s) provided.

The gap between supply piping and gas access hole may be caulked with high temperature caulk or stuffed with non-combustible,unfaced insulation to prevent cold air infiltration.

Ensure that gas line does not come in contact with outer wrap of the appliance. Follow local codes.

Pipe incoming gas line into valve compartment.

Connect incoming gas line to the 1/2 in. (13 mm) connection on manual shutoff valve.

WARNING! Risk of Fire or Explosion! Support control when attaching pipe to prevent bending gas line.

• A small amount of air will be in the gas supply lines.

WARNING! Risk of Fire or Explosion! Gas build-up during line purge could ignite.

Purge should be performed by qualified service technician.

Ensure adequate ventilation.

Ensure there are no ignition sources such as sparks or open flames.

Light the appliance. It will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Check all fittings and connections with a non-corrosivecommercially availableleak-checksolution.DO NOT use open flame. Fittings and connections could have loosened during shipping and handling.

WARNING! Risk of Fire! DO NOT change valve settings. This valve has been preset at the factory.

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

In the USA: Reduce burner orifice 4% for each 1000 feet above 2000 feet.

In CANADA: Reduce burner orifice 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

27

12 Electrical Information

A. Wiring Requirements

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric

Code CSA C22.1.

Wire the appliance junction box to 110-120VAC. This is required forr proper operation of the appliance.

A 110-120VAC circuit for this product must be protected withground-faultcircuit-interrupterprotection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

Low voltage and 110 VAC voltage cannot be shared within the same wall box.

WARNING! Risk of Shock or Explosion! DO NOT wire 110V to the valve or to the appliance wall switch. Incorrect wiring will damage controls.

C. Optional Accessories Requirements

This appliance may be used with a wall switch, wall mounted thermostat and/or a remote control.

Wiring for optional Hearth & Home Technologies approved accessories should be done now to avoid reconstruction. Follow instructions that come with those accessories.

D. Electrical Service and Repair

WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

WARNING! Risk of Shock! Replace damaged wire with type 105° C rated wire. Wire must have high temperature insulation.

B. Intellifire Ignition System Wiring

Wire the appliance junction box to 110 VAC for proper operation of the appliance.

WARNING! Risk of Shock or Explosion! DO NOT wire IPI controlled appliance junction box to a switched circuit. Incorrect wiring will override IPI safety lockout.

Refer to Figures 12.1 and 12.2, Intellifire Pilot Ignition (IPI) Wiring Diagram.

This appliance is equipped with an Intellifire control valve which operates on a 3 volt system.

Plug the 3-voltAC transformer into the appliance junction box to supply power to the unit OR install two D cell batteries (not included) into the battery pack before use.

NOTICE: Batteries should not be placed in the battery pack while using the transformer. Remove batteries before using the transformer, and unplug the transformer before installing the batteries. Battery polarity must be correct or module damage will occur.

28

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

INTERMITTENT

PILOT IGNITOR

I

IGNITION

MODULE 3 VAC

S

TRANSFORMER 3V

PLUG-IN

 

BLACK

RED

BROWN

 

BLACK

BATTERY PACK

BROWN

WHITE

ORG

GROUND TO FIREPLACE CHASSIS

ORG

GREEN

TEMP SENSOR

BLACK

VALVE

THERMOSTAT WIRE ASSEMBLY

NOTE: 1. Ignition module, valve, pilot, and wall switch operate on 3 volts. 120 VAC is required at junction box unless equipped with batteryback-up.

Figure 12.1 Intellifire Pilot Ignition (IPI) Wiring Diagram with Wall Switch or Thermostat

INTERMITTENT

PILOT IGNITOR

I

IGNITION

MODULE 3 VAC

S

TRANSFORMER 3V

PLUG-IN

 

BLACK

RED

BROWN

 

BLACK

BATTERY PACK

PLUG IN

BROWN

WHITE

ORG

GROUND TO FIREPLACE CHASSIS

ORG

GREEN

BLACK

TEMP SENSOR

REMOTE RECEIVER

Figure 12.2 Intellifire Pilot Ignition (IPI) Wiring Diagram with Remote Receiver

VALVE

NOTE: 1. Ignition module, valve, pilot, and wall switch operate on 3 volts. 120 VAC is required at junction box unless equipped with batteryback-up.

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

29

E. Junction Box Installation

If the box is being wired from the INSIDE of the appliance:

Remove the screw attaching the junction box/receptacle to the outer shell, rotate the junction box inward to disengage it from the outer shell (see Figure 12.3).

Pull the electrical wires from outside the appliance through the opening into the valve compartment and secure wires with a Romex connector. See Figure 12.3.

Make all necessary wire connections to the junction box/receptacle and reattach the junction box/receptacle to the outer shell.

F. Wall Switch Installation for Fan (Optional)

If the box is being wired to a wall mounted switch for use with a fan (See Figure 12.4):

The power supply for the appliance must be brought into a switch box.

The power can then be supplied from the switch box to the appliance using a minimum of 14-3with ground wire.

At the switch box connect the black (hot) wire and red (switch leg) wire to the wall switch as shown.

At the appliance connect the black (hot), white (neutral) and green (ground) wires to the junction box as shown.

Add a 1/4 in. insulated female connector to the red (switch leg) wire, route it through the knockout in the face of the junction box, and connect to the top fan switch connector (1/4 in. male) as shown.

 

 

 

Romex

 

 

 

Connector

 

 

 

14/2WG

 

 

 

Cover Plate

 

 

 

outside firebox

WHT

 

 

 

BLK

 

 

WHT

BLK

 

Copper

 

 

 

 

 

 

 

GRN wire

ground attached

 

 

to GRN screw with

 

 

inside box

 

 

GRN wire

 

 

 

 

 

NOTICE: DO NOT wire

 

 

110 VAC to wall switch.

Figure 12.3 Junction Box Detail

 

Minimum 14-3AWG

 

Switch

 

 

with Ground

 

 

 

Red

 

 

Black

Black

 

White

White

Junction Box

Green

Green

Red Black White Green

 

Power

 

Switch Box

 

Supply

 

 

 

 

Wires

 

Knockout

 

Red

 

 

Figure 12.4 Junction Box Wired to Wall Switch or BC10

30

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

13 Finishing

A. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.) Failure to comply could cause fire.

Combustible Mantels

 

 

 

 

 

 

 

 

 

 

 

CEILING

 

 

 

 

 

12

 

 

 

 

 

 

 

 

 

 

 

10

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

8

9

 

 

 

 

 

 

 

 

 

32

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12 13

 

4

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

10 11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TOP OF HOOD OR FIREPLACE OPENING

Note: All measurements are in inches.

Figure 13.1 Minimum Vertical and Maximum Horizontal

Dimensions of Combustibles

 

1/2 in.

3-1/2in.

SHEETROCK

NON-COMBUSTIBLE

BOARD SHIPPED

WITH APPLIANCE

1/2 in.

 

 

 

 

 

 

 

 

 

1/2 IN.

TOP VIEW

 

 

 

 

 

 

 

 

 

 

MINIMUM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2-7/8IN.

MINIMUM 3 FT. MAXIMUM

Note: Clearance from opening Alcove/Mantel leg.

Figure 13.3 Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening)

 

 

 

 

 

 

 

 

 

3 IN.

TOP VIEW

 

 

 

 

 

 

 

 

 

 

MINIMUM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5-3/8IN.

MINIMUM

UNLIMITED

Note: Clearance from opening Alcove/Mantel leg.

Figure 13.4 Non-CombustibleMantel Leg or Wall Projections (Acceptable on both sides of opening)

NON-COMBUSTIBLEZONE

Figure 13.2 Minimum Vertical and Maximum Horizontal

Dimensions of Non-Combustibles

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

31

B. Facing Material

Metal front faces may be covered with non-combustiblematerials only.

Facing and/or finishing materials must not interfere with air flow through louvers, operation of louvers or doors, or access for service.

Facing and/or finishing materials must never overhang into the glass opening.

Observe all clearances when applying combustible materials.

Seal joints between the finished wall and appliance top and sides using a 300 °F minimum sealant. Refer to Figure 13.5 and 13.6.

WARNING! Risk of Fire! DO NOT apply combustible materials beyond the minimum clearances. Comply with all minimum clearances to combustibles as specified in this manual. Overlapping materials could ignite and will interfere with proper operation of doors and louvers.

NON-COMBUSTIBLESTRIP SHIPPED WITH UNIT

Finish wall material may be combustible - Top and Sides

1 in.

0 in.

0 in.

0 in.

High Temperature Sealant (300° F/149° C min.) Top and Side Seal Joint

Figure 13.5 Noncombustible Facing Diagram

TOP SEAL

FINISH WALL MATERIAL

MAY BE COMBUSTIBLE

JOINT

TOP AND SIDES

SIDE SEAL

 

JOINT

 

 

1 INCH

 

(25 mm)

0 INCH

 

(0 mm)

 

NON-COMBUSTIBLESTRIP

 

SHIPPED WITH UNIT

 

Figure 13.6 Noncombustible Facing Diagram

32

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

14 Appliance Setup

A. Remove Glass Assembly

See Section 14.G.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the firebox.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included with accessories. Contact your dealer for a list of approved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.

RHEOSTAT

TEMPERATURE

SWITCH

 

SENSOR

Figure 14.1 Fan Wiring with Rheostat

 

VARIABLE

 

SPEED SWITCH

JUNCTION BOX

 

TEMPERATURE

 

SENSOR SWITCH

 

BLUE

 

Figure 14.2 Detail of Fan Wiring with Rheostat

E. Lava Rock, Mineral Wool/Ember Placement

Placing the Lava Rock

See Section 14.F for Lava Rock placement instructions.

WARNING! Risk of Explosion! Follow ember placement instructions in manual. DO NOT place embers directly over burner ports. Replace ember material annually. Improperly placed embers interfere with proper burner operation.

Placing the Ember Material

Ember material is shipped with this gas appliance. To place the ember material:

Embers CANNOT be placed directly over ports. See Figure 14.4 for the only exception to this guideline. Care should be taken not to cover the lighting trail of ports (from back to front).

When placing Glowing Embers® onto the burner care should be taken so that the ports are not covered. Place thedime-sizeember pieces near the port holes in the burner top (see Figure 14.3). Failure to follow this procedure will likely cause lighting and sooting problems.

Some of the small port holes should be covered with ember material. See Figure 14.4 for detail.

Save the remaining ember materials for use during appliance servicing. The embers provided should be enough for 3 to 5 applications.

NO EMBERS

LOG

Figure 14.3 Placement of Embers

PORT HOLES IN CIRCLED

AREA SHOULD BE COVERED

WITH EMBER MATERIAL. NO

OTHER PORT HOLES MAY

COME INTO CONTACT WITH

EMBER MATERIAL.

Figure 14. 4

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

33

F. Install the Log Assembly

If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions.

Note: Figure 1 illustrates the recommended gap between the burner and the lava rock retainer.

Carefully remove the logs from the packaging. CAUTION: Logs are fragile!

Log Set Assembly: LOGS-550-E,750-E,950-E

Model: SL-550TR-E,750TR-E,950TR-E,

SL-550TV-E,SL-750TV-E,SL-950TV-E

3/8 in.

Burner

Lava Rock

retainer

No lava rock may be placed past this edge.

Figure 1

Indentation

1

Slot

Figure 2

Left rear log tab

Indentation

1

Mate slot with tab

Figure 4

Log #1 : Locate the slot on the bottom right side of log 1. Mate the slot with the right rear log tab. Pull the left end of log #1 forward until it touches the left rear log tab.

Left rear log tab Right rear log tab

Shoulder screw

Lava Rock retainer

Grate tine (4)

Figure 3

Log # 2 should touch firebox

2

Figure 5

Mate notch with grate tine

 

Log #2 : Mate the left grate tine with the notch located on the left end of log #2. The right end of log #2 should rest on log #1 as shown. Be sure that the top of log # 2 touches the back of the firebox.

2118-935D6/07

34

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

3

PIN HOLE

Figure 6

Bump

Swing knot towards log #3

4

Figure 8

Mate notch with grate tine

 

Log #4: Locate the notch at the end of log # 4. Mate the notch with the tine as shown above. The top end of log #4 should rest between the end of log #2, and the bump located on log #1. Swing the knot on log # 4 towards log #3.

Figure 10

Lava Rock

 

 

 

Step #6: Apply the supplied lava rock as shown above. Take care to ensure that no lava rock is placed past the line indicated in Figure 1.

3

Mate shoulder screw with pin hole

Figure 7

Log #3: Locate the pin hole on the underside of log #3. Mate the pin hole with the shoulder screw located on the burner top. Push the left end of log # 3 toward the back of the firebox until it touches the lava rock retainer.

Bump

5

Figure 9

Mate notch with grate tine

Log #5: Locate the notch at the end of log # 5. Mate the notch with the far right grate tine. The top end of log # 5 should rest on the right side of the “bump” as shown above. You may need to move log #4 slightly.

 

SL-550TR-E

SL-750TR-E

SL-950TR-E

 

SL-550TV-E

SL-750TV-E

SL-950TV-E

 

 

 

 

Log 1

SRV2115-701

SRV2118-701

SRV2121-701

 

 

 

 

Log 2

SRV2115-702

SRV2118-702

SRV2121-702

Log 3

SRV2115-703

SRV2118-703

SRV2118-703

Log 4

SRV2115-704

SRV2118-704

SRV2121-704

Log 5

SRV2115-705

SRV2118-705

SRV2121-705

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

35

G. Fixed Glass Assembly

Removing Fixed Glass Assembly

WARNING! Risk of Asphyxiation! Handle fixed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches.

DO NOT strike, slam or scratch glass.

DO NOT operate fireplace with glass removed, cracked, broken or scratched.

Replace as a complete assembly.

Removing Fixed Glass Assembly

Pull the four glass assembly latches out of the groove on the glass frame. Remove glass door from the appliance (see Figure 14.5).

Replacing Fixed Glass Assembly

Replace the glass door on the appliance. Pull out and latch the four glass assembly latches into the groove on the glass frame.

LATCHES (BOTH BOTTOM

AND TOP)

GLASS

ASSEMBLY

Figure 14.5 Fixed Glass Assembly

H. Install the Mesh

The screen mesh is a protective barrier and must be attached to the appliance front/door.

I. Install Trim and/or Surround

Install optional trim kits and/or surrounds using the instructions included with the accessory.

Use non-combustiblematerials to cover the gap between the sheet rock and the appliance (when applicable to the model).

J. Install Hood

Hood is included with this appliance and required in all installations.

K. Air Shutter Setting

Air shutter settings should be adjusted by a qualified service technician at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer vertical runs. See Figure 14.6.

Loosen the wing nut.

Push the air handle in to close the air shutter.

Pull the air handle out to open the air shutter.

Tighten the wing nut.

NOTICE: If sooting occurs, provide more air by opening the air shutter.

SHUTTER ADJUSTMENT

Figure 14.6 Air Shutter

Air Shutter Settings

Models

NG

LP

SL-550TV-IPI-E

Fully Closed

3/16 in.

SL-750TV-IPI-E

Fully Closed

3/16 in.

SL-950TV-IPI-E

3/16 in.

3/8 in.

36

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

15 Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-freeservice. If you do experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact your dealer to arrange a service call by a qualified service technician.

A. Intellifire Ignition System

Symptom

Possible Cause

Corrective Action

 

 

 

1. Pilot won’t light.

A. Incorrect wiring.

Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are

The ignitor/module

 

connected to correct terminals on module and pilot assembly.

makes noise, but no

 

 

B. Loose connections or electrical

Verify no loose connections or electrical shorts in wiring from mod-

spark.

 

shorts in the wiring.

ule to pilot assembly. Verify connections underneath pilot assembly

 

 

are tight; also verify connections are not grounding out to metal

 

 

chassis, pilot burner, pilot enclosure, mesh screen if present, or any

 

 

other metal object.

 

 

 

 

C. Ignitor gap is too large.

Verify gap of igniter to right side of pilot hood. The gap should be

 

 

approximately .17 in. or 1/8 in. (3 mm).

 

 

 

 

D. Module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove

 

 

ignitor wire “I” from module. Place a grounded wire about 3/16 in. (5

 

 

mm) away from “I” terminal on module. Place ON/OFF rocker switch

 

 

or wall switch in ON position. If there is no spark at “I” terminal module

 

 

must be replaced. If there is a spark at “I” terminal, module is fine.

 

 

Inspect pilot assembly for shorted sparker wire or cracked insulator

 

 

around electrode. Replace pilot if necessary.

 

 

 

2. Pilot won’t light,

A. No power or transformer installed

Verify that transformer is installed and plugged into module. Check

there is no noise or

incorrectly.

voltage of transformer under load at spade connection on module

spark.

 

with ON/OFF switch in ON position. Acceptable readings of a good

 

 

transformer are between 3.2 and 2.8 volts AC.

 

 

 

 

B. A shorted or loose connection in

Remove and reinstall the wiring harness that plugs into module.

 

wiring configuration or wiring har-

Verify there is a tight fit. Verify pilot assembly wiring to module. Re-

 

ness.

move and verify continuity of each wire in wiring harness. Replace

 

 

any damaged components.

 

 

 

 

C. Improper wall switch wiring.

Verify that 110/VAC power is “ON” to junction box.

 

 

 

 

D. Module not grounded.

Verify black ground wire from module wire harness is grounded to

 

 

metal chassis of appliance.

 

 

 

 

E. Module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove

 

 

ignitor wire “I” from module. Place ON/OFF rocker switch or wall

 

 

switch in ON position. If there is no spark at “I” terminal module

 

 

must be replaced. If there is a spark at “I” terminal, module is fine.

 

 

Inspect pilot assembly for shorted sparker wire or cracked insulator

 

 

around electrode.

 

 

 

3. Pilot sparks, but

A. Gas supply.

Verify that incoming gas line ball valve is “open”. Verify that inlet

Pilot will not light.

 

pressure reading is within acceptable limits, inlet pressure must not

 

 

exceed 14 in. W.C.

 

 

 

 

B. Ignitor gap is too large.

Verify gap of igniter to right side of pilot hood. The gap should be

 

 

approximately .17 in. or 1/8 in. (3 mm).

 

 

 

 

C. Module is not grounded.

Verify module is securely grounded to metal chassis of appliance.

 

 

 

 

D. Module voltage output / Valve/Pilot

Verify battery voltage is at least 2.7 volts. Replace batteries if volt-

 

solenoid ohms readings.

age is below 2.7.

 

 

 

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

37

Intellifire Ignition System - (continued)

Symptom

Possible Cause

Corrective Action

 

 

 

 

A. A shorted or loose connection in flame

Verify all connections to wiring diagram in manual. Verify

4. Pilot lights but contin-

sensing rod.

connections underneath pilot assembly are tight. Verify con-

ues to spark, and main

 

nections are not grounding out to metal chassis, pilot burn-

burner will not ignite.

 

er, pilot enclosure or screen if present, or any other metal

(If the pilot continues

 

object.

to spark after the

 

 

B. Poor flame rectification or contaminated

With fixed glass assembly in place, verify that flame is en-

pilot flame has been lit,

flame sensing rod.

gulfing flame sensing rod on left side of pilot hood. Flame

flame rectification has

 

sensing rod should glow shortly after ignition. Verify cor-

not occurred.)

 

 

rect pilot orifice is installed and gas inlet is set to pressure

 

 

 

 

specifications. Clean flame sensing rod with emery cloth to

 

 

remove any contaminants that may have accumulated on

 

 

flame sensing rod.

 

 

 

 

C. Module is not grounded.

Verify module is securely grounded to metal chassis of ap-

 

 

pliance. Verify that wire harness is firmly connected to the

 

 

module.

 

 

 

 

D. Damaged pilot assembly or contami-

Verify that ceramic insulator around the flame sensing rod

 

nated flame sensing rod.

is not cracked, damaged, or loose. Verify connection from

 

 

flame sensing rod to white sensor wire. Clean flame sensing

 

 

rod with emery cloth to remove any contaminants that may

 

 

have accumulated on flame sensing rod. Verify continuity

 

 

with a multimeter with ohms set at lowest range. Replace

 

 

pilot if any damage is detected.

 

 

 

 

E. Module.

Turn ON/OFF rocker switch or wall switch to OFF position.

 

 

Remove ignitor wire “I” from module. Place ON/OFF rocker

 

 

switch or wall switch in ON position. If there is no spark at “I”

 

 

terminal module must be replaced. If there is a spark at “I”

 

 

terminal, module is fine.

 

 

 

38

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

16 Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.

 

N

M

L

 

 

 

 

 

O

 

 

J

 

 

 

K

 

P

 

 

S

D F G

E

GAS LINE

ACCESS

R

H

ELECTRICAL

ACCESS

 

 

 

 

Q

 

 

 

 

 

 

 

 

 

 

 

 

B

 

 

 

 

 

 

 

 

 

 

I

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

B

C

D

E

 

F

G

H

I

J

K

L

M

N

O

 

P

 

Q

R

S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SL-550TV-E

in.

36

 

31

 

 

1

18-1/16

27-3/16

 

30

31-1/16

5-1/2

3-13/16

16-5/16

8-3/8

1/2

25-3/4

12-7/8

15-13/16

5-1/16

 

6

 

2-3/16

34-5/16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mm

913

 

790

 

 

25

459

691

 

762

789

140

97

415

213

14

654

327

402

129

 

153

56

872

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SL-750TV-E

in.

41

 

36

 

 

1

21-1/2

32-1/16

 

33-9/16

34-9/16

5-1/2

3-13/16

16-5/16

8-3/8

1/2

30-3/4

15-3/8

15-13/16

5-1/16

 

6

 

2-3/16

37-7/8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mm

1040

 

917

 

 

25

546

815

 

853

878

140

97

415

213

14

751

391

402

129

 

153

56

962

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SL-950TV-E

in.

48

 

43

 

 

1

23-9/16

39-1/16

 

37-9/16

38-9/16

5-1/2

3-13/16

16-5/16

8-3/8

1/2

37-3/4

18-7/8

15-13/16

6-1/16

 

6

 

2-3/16

41-3/4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mm

1218

 

1095

 

 

25

599

993

 

954

980

140

97

415

213

14

959

480

402

129

 

153

56

1061

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 16.1 Appliance Dimensions

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

39

B. Service Parts

SL-550TV-IPI-E

 

 

Service Parts Diagram

Beginning Manufacturing Date: June 2007

 

Ending Manufacturing Date:_________

6

9 8

10

7

12

11

Log Set Assembly

2

4 1 5

3

Part number list on following page.

40

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

Service Parts List

 

SL-550TV-IPI-E

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

 

 

 

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

 

in this manual may be ordered from an authorized dealer.

 

 

 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

 

 

Log Set Assembly

 

LOGS-550-E

 

Y

1

Log 1

 

SRV2115-701

 

 

2

Log 2

 

SRV2115-702

 

 

3

Log 3

 

SRV2115-703

 

 

4

Log 4

 

SRV2115-704

 

 

5

Log 5

 

SRV2115-705

 

 

6

Burner NG, LP

 

2115-007

 

Y

7

Grate Assembly

 

2115-015

 

 

8

Glass Door Assembly

 

GLA-550TR

 

Y

9

Door

 

2116-020

 

 

 

Mesh Assembly

 

2115-036

 

Y

10

Hood

 

2115-230

 

 

11

Air Chute

 

2119-154

 

 

12

Junction Box

 

4021-013

 

Y

 

 

 

 

 

 

 

Glass Latch Assembly

 

386-122A

 

Y

 

High Limit Switch

 

066-531

 

Y

 

Lava Rock

 

060-721

 

 

 

Mineral Wool

 

050-721

 

 

 

Non-combustibleboard

 

547-401

 

 

 

Pilot Tube

 

SRV485-301

 

Y

 

Touch Up Paint

 

TUP-GBK-12

 

 

 

Conversion Kit NG

NGK-550IPIE

Y

 

Conversion Kit LP

LPK-550IPIE

Y

 

Pilot Orifice NG

593-528

Y

 

Pilot Orifice LP

593-527

Y

 

Regulator NG

NGK-DXV

Y

 

Regulator LP

LPK-DXV

Y

Additional service part numbers appear on following page.

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

41

Service Parts

SL-750TV-IPI-E

Service Parts Diagram

Beginning Manufacturing Date: June 2007

 

Ending Manufacturing Date: ________

6

9 8

10

7

12

11

Log Set Assembly

2

4 1 5

3

Part number list on following page.

42

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

Service Parts List

 

SL-750TV-IPI-E

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

 

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

 

Log Set Assembly

 

LOGS-750-E

Y

1

Log 1

 

SRV2118-701

 

2

Log 2

 

SRV2118-702

 

3

Log 3

 

SRV2118-703

 

4

Log 4

 

SRV2118-704

 

5

Log 5

 

SRV2118-705

 

6

Burner NG, LP

 

2118-007

Y

7

Grate Assembly

 

2118-015

 

8

Glass Door Assembly

 

GLA-750TR

Y

9

Door

 

2119-020

 

 

Mesh Assembly

 

2118-036

Y

10

Hood

 

2118-230

 

11

Air Chute

 

2119-154

 

12

Junction Box

 

4021-013

Y

 

 

 

 

 

 

Glass Latch Assembly

 

386-122A

Y

 

High Limit Switch

 

066-531

Y

 

Lava Rock

 

060-721

 

 

Mineral Wool

 

050-721

 

 

Non-CombustibleBoard

 

534-401

 

 

Pilot Tube

 

SRV485-301

Y

 

Touch Up Paint

 

TUP-GBK-12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Conversion Kit NG

 

NGK-750IPIE

Y

 

Conversion Kit LP

 

LPK-750IPIE

Y

 

Pilot Orifice NG

 

593-528

Y

 

Pilot Orifice LP

 

593-527

Y

 

Regulator NG

 

NGK-DXV

Y

 

Regulator LP

 

LPK-DXV

Y

Additional service part numbers appear on following page.

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

43

Service Parts

SL-950TV-IPI-E

Service Parts Diagram

Beginning Manufacturing Date: June 2007

 

Ending Manufacturing Date: ________

6

10 9 8

7

12

11

Log Set Assembly

2

4 1 5

3

Part number list on following page.

44

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

Service Parts List

 

SL-950TV-IPI-E

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

 

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

 

Log Set Assembly

 

LOGS-950-E

Y

1

Log 1

 

SRV2121-701

 

2

Log 2

 

SRV2121-702

 

3

Log 3

 

SRV2118-703

 

4

Log 4

 

SRV2121-704

 

5

Log 5

 

SRV2121-705

 

6

Burner NG, LP

 

2121-007

Y

7

Grate Assembly

 

2121-015

 

8

Glass Door Assembly

 

GLA-950TR

Y

9

Door

 

2122-020

 

 

Mesh Assembly

 

2121-035

Y

10

Hood

 

2121-230

 

11

Air Chute

 

2119-154

 

12

Junction Box

 

4021-013

Y

 

 

 

 

 

 

Glass Latch Assembly

 

386-122A

Y

 

High Limit Switch

 

066-531

Y

 

Lava Rock

 

060-721

 

 

Mineral Wool

 

050-721

 

 

Non-CombustibleBoard

 

560-401

 

 

Pilot Tube

 

SRV485-301

Y

 

Touch Up Paint

 

TUP-GBK-12

 

 

Conversion Kit NG

NGK-950IPIE

Y

 

Conversion Kit LP

LPK-950IPIE

Y

 

Pilot Orifice NG

593-528

Y

 

Pilot Orifice LP

593-527

Y

 

Regulator NG

NGK-DXV

Y

 

Regulator LP

LPK-DXV

Y

Additional service part numbers appear on following page.

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

45

Service Parts

SL-550 /750 /950TV-IPI-E

 

 

Valve Assembly Parts List

Beginning Manufacturing Date: June 2007

 

Ending Manufacturing Date: ______

IPI Valve Assembly

1

2

13

 

12

 

3

 

 

 

 

 

4

 

 

 

11

 

5

 

 

 

 

 

 

 

 

10

 

 

 

 

 

 

 

 

6

 

 

 

9

7

 

 

 

 

8

 

 

 

 

 

 

 

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

 

at Depot

ITEM

DESCRIPTION

 

COMMENTS

PART NUMBER

 

1

Pilot Assembly NG

 

 

2090-012

Y

Pilot Assembly LP

 

 

2090-013

Y

 

 

 

2

Shutter Bracket Assembly

 

 

2118-121

Y

 

Orifice NG (#44C)

 

SL-550TV-IPI-E

582-844

Y

 

Orifice LP (#55C)

 

582-855

Y

 

 

 

3

Orifice NG (#42C)

 

SL-750TV-IPI-E

582-842

Y

Orifice LP (#54C)

 

582-854

Y

 

 

 

 

Orifice NG (#37C)

 

SL-950TV-IPI-E

582-837

Y

 

Orifice LP (#55C)

 

582-855

Y

 

 

 

4

Flexible Gas Connector

 

 

7000-156

Y

5

Battery Pack

 

 

593-594A

Y

6

Wire Assembly 80" & 72"

 

 

522-504A

Y

7

3 Volt Transformer

 

 

593-593A

Y

8

Module Wire Assembly

 

 

593-590A

Y

9

Module

 

 

593-592

Y

10

Thermostat Wire Assembly

 

 

2118-170

Y

11

Valve NG

 

 

750-500

Y

Valve LP

 

 

750-501

Y

 

 

 

12

Flex Ball Valve Assembly

 

 

302-320A

Y

13

Valve Bracket

 

 

2118-104

 

46

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

C. Contact Information

Heat & Glo, a brand of Hearth & Home Technologies Inc. 7571 215th St, Lakeville, MN 55044 www.heatnglo.com

Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

- NOTES -

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

and maintenance

these instructions for safe

instructions included.

installation and operation.

Leave this manual with party responsible for use and operation.

This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588,

6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940,

6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.

Printed in U.S.A. - Copyright 2009

Heat & Glo • SL-550 /750 /950TV-IPI-E2119-900Rev. J • 12/09

47