Heat & Glo LifeStyle SL-950TR-D User Manual

Size:
9.17 Mb
Download

Owner’s Manual

Installation and Operation

Models:

SL-550TR-D

SL-750TR-D

SL-950TR-D

CAUTION

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

• Leave this manual with

and maintenance

these instructions for safe

party responsible for use

instructions included.

installation and operation.

and operation.

DO DISCARDNOT

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

What to do if you smell gas

-Do not try to light any appliance.

-Do not touch any electrical switch. Do not use any phone in your building.

-Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the manufactured home construction and safety standard,

Title 24 CFR, Part 3280 or Standard for Installation in Mobile Homes, CAN/CSA Z240MH.

This appliance is only for use with the type(s) of gas indicated on the rating plate.

WARNING

HOT! DO NOT TOUCH.

SEVERE BURNS MAY RESULT. CLOTHING IGNITION MAY RESULT.

Glass and other surfaces are hot during operation and cool down.

Keep children away.

CAREFULLY SUPERVISE children in same room as appliance.

Alert children and adults to hazards of high temperatures.

Do NOT operate with protective barriers open or removed.

Keep clothing, furniture, draperies and other combustibles away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. Do NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

In the Commonwealth of Massachusetts:

installation must be performed by a licensed plumber or gas fitter;

See Table of Contents for location of additional Commonwealth of Massachusetts requirements.

Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory-trainedprofessionals, or technicians super-

vised by an NFI certified professional.

Heat & Glo • SL-550 /750 /950TR-D• InD •2044-985Rev. M • 10/06

1

 

NATURAL GAS

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

Congratulations

Congratulations on selecting a Heat & Glo gas appliance —anelegant and clean alternative to wood burning appliances. The Heat & Glo gas appliance you have selected is designed to provide the utmost in safety, reliability, and efficiency.

As the owner of a new appliance, you’ll want to read and carefully follow all of the instructions contained in this Owner’s Manual. Pay special attention to all Cautions and Warnings.

This Owner’s Manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this Owner’s Manual, unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo gas appliance will give you years of durable use and trouble-freeenjoyment. Welcome to the Heat & Glo family of appliance products!

Homeowner Reference Information

We recommend that you record the following pertinent information about your appliance.

Model Name: ___________________________________________ Date purchased/installed:__________________

Serial Number:__________________________________________ Location on appliance: ____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

Listing Label Information/Location The model information regarding your specific appliance can be found on the rating plate usually located in the control area of the appliance.

Type of Gas

Gas and Electric

Information

This product may be covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevets suivants): (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending (ou autres brevets americains et etrangers en attente).

Heat & Glo, abrand of Hearth & Home Technologies, Inc.

20802 Kensington Boulevard, Lakeville, MN 55044

Not for usewithsolidfuel.

(Nedoitpasentreutiliseavecuncombustiblesolide).

TypeofGas (Sorte De Gaz): Thisappliancemustbeinstalledinaccordancewithlocalcodes, ifany;ifnot,followANSIZ223.1intheUSAorCAN/CGAB149 installationcodes.(Installer l’appareil selon les codes ou reglements locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)

ANSI Z21XX-XXXX· CSA2.XX-MXX· UL307B

MinimumPermissibleGasSupplyfor PurposesofInputAdjustment.

 

 

 

ApprovedMinimum (De Gaz) Acceptable

0.0inw.c.

(Po.Col.d’eau)

 

 

 

MaximumPressure(Pression)

 

0.0inw.c.

(Po.Col.d’eau)

 

 

 

MaximumManifoldPressure(Pression)

0.0inw.c.

(Po.Col.d’eau)

 

 

 

MinimumManifoldPressure(Pression)

0.0inw.c.

(Po.Col.d’eau)

 

 

 

TotalElectricalRequirements: 000Vac,00Hz.,lessthan00Amperes

MADE IN USA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INCANADA

 

Model:

XXXXXXXX

 

ALTITUDE:

0-0000FT.

0000-0000FT.

 

(Modele):

 

MAX. INPUT BTUH:

00,000

00,000

 

 

 

 

 

 

 

MIN.INPUTBTUH:

00,000

00,000

 

Serial

XXXXXXXX

 

ORIFICESIZE:

#XXXXX

#XXXXX

 

 

 

(Serie):

 

Model Number

Serial Number

2

Heat & Glo • SL-550 /750 /950TR-D• InD •2044-985Rev. M • 10/06

- Table of Contents-

Section 1: Listing and Code Approvals

 

 

A. Appliance Certification...................................

4

 

B. Glass Specifications ......................................

4

 

C. BTU Specifications ........................................

4

 

D. High Altitude Installations ..............................

4

 

E. Non-CombustibleMaterials Specification......

4

 

F. Combustible Materials Specification..............

4

 

G. Requirements for the Commonwealth

 

 

of Massachusetts...........................................

5

Section 2:

Getting Started

 

 

A. Design and Installation Considerations .........

6

 

B. Tools and Supplies Needed...........................

6

 

C. Inspect Appliance and Components..............

6

Section 3: Framing and Clearances

 

 

A. Selecting Appliance Location.........................

7

 

B. Constructing the Appliance Chase ................

8

 

C. Clearances ....................................................

8

 

D. Mantel Projections.........................................

9

Section 4:

Termination Locations

 

 

A. Vent Termination Minimum Clearances .......

10

Section 5: Vent Information and Diagrams

 

 

A. Vent Table Key.............................................

12

 

B. Use of Elbows..............................................

12

 

C. Measuring Standards ..................................

12

 

D. Use of Flex Vent ..........................................

13

Î

E. Vent Diagrams.............................................

14

Section 6: Vent Clearances and Framing

 

 

A. Pipe Clearances to Combustibles ...............

24

 

B. Wall Penetration Framing ............................

24

 

C. Vertical Penetration Framing .......................

25

Section 7:

Appliance Preparation

 

 

A. Top Vent.......................................................

26

 

B. Rear Vent.....................................................

27

 

C. Securing and Leveling the Appliance ..........

28

Section 8: Installing Vent Pipe

 

 

A. Assembly of Vent Sections for DVP Pipes ..

29

 

B. Disassembly of Vent Sections .....................

31

 

C. Installing Heat Shield and

 

 

Horizontal Termination Cap ........................

33

 

D. Installing Roof Flashing and Vertical

 

 

Termination Cap ..........................................

35

Section 9:

Gas Information

 

 

A. Fuel Conversions......................................

37

 

B. Gas Pressures ..........................................

37

 

C. Gas Connection ........................................

37

Section 10:

Electrical Information

 

 

A. Recommendation for Wire ........................

39

 

B. Connecting to the Appliance .....................

39

 

C. Standing Pilot Ignition System Wiring.......

40

 

D. Intellifire Ignition System Wiring................

40

 

E. Junction Box Installation ...........................

41

 

F.

Wall Switch Installation for Fan.................

41

Section 11:

Finishing

 

 

A. Mantel Projections ....................................

42

 

B.

Facing Material .........................................

42

Section 12:

Appliance Setup

 

 

A. Remove Shipping Materials......................

43

 

B. Clean the Appliance..................................

43

 

C. Accessories ..............................................

43

 

D. Positioning the Logs .................................

44

 

E. Glass Assembly ........................................

48

 

F.

Grilles and Trim.........................................

48

Section 13:

Operating Instructions

 

 

A. Before Lighting Appliance .........................

49

 

B. Lighting Appliance.....................................

50

 

C. After Appliance is Lit .................................

52

 

D. Frequently Asked Questions.....................

52

Section 14:

Troubleshooting

 

 

A. Standing Pilot Ignition System ..................

53

 

B. Intellifire Ignition System...........................

54

Section 15:

Maintaining and Servicing Appliance...........

57

Section 16:

Reference Materials

 

 

A. Appliance Dimension Diagram .................

59

 

B. Vent Components Diagrams.....................

60

 

C. Service Parts ............................................

65

 

D. Warranty ...................................................

68

 

E. Contact Information ..................................

69

Î

Heat & Glo • SL-550 /750 /950TR-D• InD •2044-985Rev. M • 10/06

3

 

1 Listing and Code Approvals

A. Appliance Certification

MODELS: SL-550TR-D,SL-750TR-D,SL-950TR-DLABORATORY: Underwriters Laboratories, Inc. (UL)TYPE: Direct Vent Gas Appliance Heater

STANDARD: ANSIZ21.88-2002CSA2.33-M02• UL307B

This product is listed to ANSI standards for “Vented Gas Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

B. Glass Specifications

Hearth & Home Technologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the Consumer Product Safety Commission (CPSC). The tempered glass has been tested and certified to the requirements of ANSI Z97.1 andCPSC 16 CFR 1202 (Safety Glazing Certification CouncilSGCC# 1595 and1597. Architectural Testing, Inc. Reports02-31919.01 and02-31917.01).

This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements” which refers to15 U.S. Code(USC) 2063 stating “…Such certificate shall accompany the product or shall otherwise be furnished to any distributor or retailer to whom the product is delivered.”

Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory. Please contact your dealer or distributor to order.

C. BTU Specifications

Models

Maximum Minimum Orifice

U.S. (0-2000ft.) or

Input

Input

Size

Canada (2000-4500ft.)

BTU/h

BTU/h

(DMS)

SL-550TR-D(NG)

U.S.

21,000

12,000

#44

SL-550TR-IPI-D(NG)

Canada

18,900

10,800

#45

SL-550TRLP-D(LP)

U.S.

20,000

12,000

#54

SL-550TRLP-IPID(LP)

Canada

18,000

10,800

#55

SL-750TR-D(NG)

U.S.

23,000

13,500

#42

SL-750TR-IPI-D(NG)

Canada

20,700

12,150

#43

SL-750TRLP-D(LP)

U.S.

23,000

13,500

#53

SL-750TRLP-IPID(LP)

Canada

20,700

12,150

#54

SL-950TR-D(NG)

U.S.

30,000

18,500

#36

SL-950TR-IPI-D(NG)

Canada

27,000

16,650

#37

SL-950TR-D(LP)

U.S.

30,000

18,500

#51

SL-950TR-IPI-D(LP)

Canada

27,000

16,650

#52

D. High Altitude Installations

U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and Canada.

When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A., or 10% for elevations between 2000 and 4500 feet in Canada. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.

If installing this appliance at an elevation above 4500 feet (in Canada), check with local authorities.

WARNING

Do NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

NOTE: This installation must conform with local codes. In the absence of local codes you must comply with theNational Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and theCAN/CGA B149 Installation Codes in Canada.

E. Non-CombustibleMaterials Specification

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750oC,shall be considered non-combustible materials.

F. Combustible Materials Specification

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite and burn, whether flame proofed or not, or whether plastered or unplastered shall be considered combustible materials.

4

Heat & Glo • SL-550 /750 /950TR-D• InD •2044-985Rev. M • 10/06

NOTE: The following requirements reference various Massachusetts and national codes not contained in this document.

G.Requirements for the Commonwealth of Massachusetts

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven

(7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-upis installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-upmay be installed on the next adjacent floor level. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

Signage

A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half(1/2) inch in size,

“GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

Detailed instructions for the installation of the venting system design or the venting system components; and

A complete parts list for the venting system design or venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the manufacturer:

The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and

The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

Heat & Glo • SL-550 /750 /950TR-D• InD •2044-985Rev. M • 10/06

5

 

2 Getting Started

A. Design and Installation Considerations

Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required.

CAUTION

Check building codes prior to installation.

Installation MUST comply with local, regional, state and national codes and regulations.

Consult local building, fire officials or authorities having jurisdiction about restrictions, installation inspection, and permits.

When planning an appliance installation, it’s necessary to determine the following information before installing:

Where the appliance is to be installed.

The vent system configuration to be used.

Gas supply piping.

Electrical wiring.

Framing and finishing details.

Whether optional accessories—devicessuch as a fan, wall switch, or remotecontrol—aredesired.

C. Inspect Appliance and Components

WARNING

Inspect appliance and components for damage. Damaged parts may impair safe operation.

• Do NOT install damaged components.

Do NOT install incomplete components.

Do NOT install substitute components. Report damaged parts to dealer.

Carefully remove the appliance and components from the packaging.

The vent system components and trim doors are shipped in separate packages.

The gas logs may be packaged separately and must be field installed.

Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

 

WARNING

WARNING

 

Hearth & Home Technologies disclaims any

Keep appliance dry.

responsibility for, and the warranty will be voided

• Mold or rust may cause odors.

by, the following actions:

• Water may damage controls.

• Installation and use of any damaged appliance or vent

 

 

 

 

system component.

B. Tools and Supplies Needed

• Modification of the appliance or vent system.

• Installation other than as instructed by Hearth & Home

Before beginning the installation be sure that the following

Technologies.

tools and building supplies are available.

• Improper positioning of the gas logs or the glass door.

Reciprocating saw

Framing material

• Installation and/or use of any component part not

 

 

Pliers

Hi temp caulking material

approved by Hearth & Home Technologies.

Hammer

Gloves

Any such action may cause a fire hazard.

Phillips screwdriver

Framing square

 

Flat blade screwdriver

Electric drill and bits (1/4 in.)

 

Plumb line

Safety glasses

 

Level

1/2 - 3/4 inch length, #6 or #8 Self-drillingscrews

Manometer

Voltmeter

 

Tape measure

Noncorrosive leak check solution

 

One 1/4 inch female connection (for optional fan).

6

Heat & Glo • SL-550 /750 /950TR-D• InD •2044-985Rev. M • 10/06

3 Framing and Clearances

NOTE:

Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY.

Illustrations/diagrams are not drawn to scale.

Actual installation may vary due to individual design preference.

A.Selecting Appliance Location

WARNING

Fire Risk

Provide adequate clearance:

Around air openings

To combustibles

For service access

Locate appliance away from traffic areas.

When selecting a location for your appliance it is important to consider the required clearances to walls (see Figure 3.1).

NOTE: For actual appliance dimensions refer to Section 16.

A

E

F

D

C

In addition to these framing dimensions, also reference the following sections:

Clearances and Mantel Projections (Section 3.C and 3.D)

Vent Clearances and Framing (Section 6).

H

B

I

 

 

 

 

 

 

 

 

G

 

 

 

 

 

 

 

 

 

 

 

 

 

Models

 

A

B

C

D

E

F

G

H

I

SL-550TR-IPI-D

Inches

41-1/2

37

58-3/4

 

1

1/2

48-1/2

68-1/4

16-1/4

SL-550TR-D

Millimeters

1054

940

1492

 

25

13

1232

1734

413

SL-750TR-IPI-D

Inches

45

42

63-3/4

See Section D for

1

1/2

52

73-1/4

16-1/4

SL-750TR-D

Millimeters

1143

1067

1619

Alcove Installation

25

13

1321

1861

413

SL-950TR-IPI-D

Inches

50

49

70-3/4

 

1

1/2

57

80-1/4

16-1/4

SL-950TR-D

Millimeters

1270

1245

1797

 

25

13

1448

2038

413

Figure 3.1 Appliance Locations

Heat & Glo • SL-550 /750 /950TR-D• InD •2044-985Rev. M • 10/06

7

 

B. Constructing the Appliance Chase

A chase is a vertical boxlike structure built to enclose the gas appliance and/or its vent system. Vertical vents that run on the outside of a building may be, but are not required to be, installed inside a chase.

Construction of the chase may vary with the type of building. These instructions are not substitutes for the requirements of local building codes. Local building codes MUST be checked.

Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building envelope in any manner.

Walls, ceiling, base plate and cantilever floor of the chase should be insulated. Vapor and air infiltration barriers should be installed in the chase as per regional codes for the rest of the home. Additionally, in regions where cold air infiltration may be an issue, the inside surfaces may be sheetrocked and taped for maximum air tightness.

To further prevent drafts, the wall shield and ceiling firestops should be caulked with high temperature caulk to seal gaps.

Gas line holes and other openings should be caulked with high temp caulk or stuffed with unfaced insulation. If the appliance is being installed on a cement slab, a layer of plywood may be placed underneath to prevent conducting cold up into the room.

C. Clearances

WARNING

Fire Risk.

Odor Risk.

Install appliance on hard metal or wood surfaces extending full width and depth of appliance.

Do NOT install appliance directly on carpeting, vinyl, tile or any combustible material other than wood.

WARNING

Fire Risk.

Construct chase to all clearance specifications in manual.

Locate and install appliance to all clearance specifications in manual

FROM TOP

A OF HOOD

TO CEILING

E

F

H

B

 

 

 

C

 

 

 

 

J

G

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D

 

 

 

 

 

 

 

I

 

 

 

 

 

A

 

B

C

 

D

E

F

G

H

I

J

 

 

DVP Pipe

SL Pipe

Rough

DVP Pipe

SL Pipe

Rough

 

Non-

 

 

 

 

Models

Rough

Rough

Rough

Rough

Clearance

Combustible

Behind

Sides of

Front of

 

 

Opening

Opening

to Ceiling

Combustible

Flooring

Appliance

Appliance

Appliance

 

 

Opening

Opening

Opening

Opening

 

 

(Height)

(Width)

 

Floor

 

 

 

 

 

 

(Width)

(Width)

 

(Depth)

(Depth)

 

 

 

 

 

 

 

SL-550TR-D

in.

10

8-5/8

33

27-1/2

16-1/4

37

31

0

0

1/2

1/2

36

mm

254

219

838

699

413

940

787

0

0

13

13

915

SL-750TR-D

in.

10

8-5/838-1/4

27-1/2

16-1/4

42

31

0

0

1/2

1/2

36

mm

254

219

971

699

413

1067

787

0

0

13

13

915

SL-950TR-D

in.

10

8-5/8

42 1/4

27-1/2

16-1/4

49

31

0

0

1/2

1/2

36

mm

254

219

1073

699

413

1245

787

0

0

13

13

914

Figure 3.2 Clearances to Combustibles

8

Heat & Glo • SL-550 /750 /950TR-D• InD •2044-985Rev. M • 10/06

D. Mantel Projections

1”

2 ”

Figure 3.3 Clearances to Mantels or other Combustibles above Appliance

Note: Clearance from opening to perpendicular wall.

Figure 3.4 Clearances to Mantel Legs or Wall Projections (Acceptable on both sides of opening.)

Heat & Glo • SL-550 /750 /950TR-D• InD •2044-985Rev. M • 10/06

9

 

4 Termination Locations

A. Vent Termination Minimum Clearances

WARNING

Fire Risk. Explosion Risk.

Maintain vent clearance to combustibles as specified.

Do not pack air space with insulation or other materials.

Failure to keep insulation or other materials away from vent pipe may cause fire.

Measure vertical clearances from this surface.

Measure horizontal clearances from this surface.

(See Figure 4.4 for specific clearances)

Figure 4.1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

 

 

 

 

 

 

 

 

 

 

 

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

 

 

 

 

 

 

 

 

 

H (Min.) Ft.

Flat to 6/12...........................................................

1.0*

Over 6/12 to 7/12.................................................

1.25*

Over 7/12 to 8/12.................................................

1.5*

Over 8/12 to 9/12.................................................

2.0*

Over 9/12 to 10/12...............................................

2.5

Over 10/12 to 11/12 .............................................

3.25

Over 11/12 to 12/12 .............................................

4.0

Over 12/12 to 14/12.............................................

5.0

Over 14/12 to 16/12.............................................

6.0

Over 16/12 to 18/12.............................................

7.0

Over 18/12 to 20/12.............................................

7.5

Over 20/12 to 21/12.............................................

8.0

* 3 foot minimum in snow regions

Figure 4.2 Minimum Height from Roof to Lowest Discharge Opening

Figure 4.2 specifies minimum vent heights for various pitched roofs.

 

 

 

 

 

GAS, WOOD OR FUEL

 

 

 

 

 

 

 

 

 

 

OIL TERMINATION

 

 

 

20 IN.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(MINIMUM) TO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PERPENDICULAR

 

 

 

 

 

 

 

 

GAS

 

 

 

 

 

WALL

 

 

 

 

 

TERMINATION

 

 

 

(GAS ON LY)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Gas Termination

Wood & Fuel Oil Termination

 

 

 

A

6 in.

20 in.

Figure 4.3 Multiple Vertical Termination

10

Heat & Glo • SL-550 /750 /950TR-D• InD •2044-985Rev. M • 10/06