Page 1
USER MANUAL EN.
QUBINO FLUSH SHUTTER
The Qubino Flush Shutter module is ideal for remotely controlling the motors of blinds, rollers,
shades, venetian blinds, etc.
Page 2
EN.
Table of contents
About Qubino ................................................................................................................................................................ 3
Safety Information ......................................................................................................................................................... 5
Flush Shutter - Available Frequencies ........................................................................................................................... 6
Where To Buy ................................................................................................................................................................ 7
1. Introduction ............................................................................................................................................................... 7
2. Use Cases ................................................................................................................................................................... 9
2.1. Installation examples where Flush Shutter is installed behind a wall switch .................................................... 9
2.4. Additional features of Flush Shutter which can make your life easier ............................................................ 11
3. Qubino Flush Shutter Advantages and Highlights ................................................................................................... 12
4. Package Contents .................................................................................................................................................... 16
5. Technical Terms for Switches .................................................................................................................................. 17
6. Compatibility with Z-Wave Gateways (hubs) .......................................................................................................... 19
7. Installation ............................................................................................................................................................... 20
7.1. Installing the device behind a light switch ....................................................................................................... 21
7.2. Installing the Qubino Temperature Sensor ...................................................................................................... 27
8. Device Information and Support ............................................................................................................................. 33
9. Electrical Diagram (110 - 230VAC, 24VDC) .............................................................................................................. 34
10. Adding the device to a Z-Wave network (Inclusion) .............................................................................................. 35
11. Removing the device from a Z-Wave network (Exclusion) .................................................................................... 36
12. Associations ........................................................................................................................................................... 37
13. Flush Shutter Calibration ....................................................................................................................................... 39
14. Configuration Parameters ..................................................................................................................................... 42
15. Technical Specifications ......................................................................................................................................... 50
16. Z-Wave Command Classes ..................................................................................................................................... 52
17. Important Disclaimer ............................................................................................................................................. 55
18. Warning ................................................................................................................................................................. 55
19. Regulations ............................................................................................................................................................ 55
2
Page 3
EN.
About Qubino
Qubino is a family of innovative Z-Wave devices, many of them the smallest of their kind.
Numerous breakthrough innovations, 100% quality control, and responsive customer service
make Qubino the number one choice for making your life more comfortable.
Qubino enables you to transform – inexpensively and invisibly – any traditional electric device
into a smart, connected one that you can control with your smart phone. Qubino devices are
simple to install and use, but also extremely versatile - they offer a wealth of additional features
and parameters for you to play with.
We love helping people who enjoy creating new ideas for their home and then using their hard
work and skill to turn those ideas into reality. We admire their passion and resourcefulness. We
do our best to supply you with products that will enable you to create a unique and special
home for yourself. We innovate so that you can be free to make the smartest home possible.
With just a touch of magic.
"Simple is smart." We believe it is smart to make complex things simple. But only when this
means simple for our customers, not for ourselves. We think a lot so that you won't have to
when it comes to installing or using our devices.
For more information visit: www.qubino.com
3
Page 4
EN.
About Z-Wave:
The Z-Wave protocol is an interoperable, wireless, RF-based communications technology
designed specifically for control, monitoring, and status reading applications in residential and
light commercial environments. Mature, proven, and broadly deployed (with over 50 million
products sold worldwide), Z-Wave is by far the world market leader in wireless control, bringing
affordable, reliable, and easy-to-use 'smart' products to millions of people in every aspect of
daily life.
Source: www z-wavealliance.org
4
Page 5
EN.
Safety Information
For Qubino, safety is first, so we have prepared lots of safety tips and information that can be
found throughout this manual.
To ensure your safety, please read this manual carefully before installing the device; follow
the instructions exactly. The manufacturer (GOAP d.o.o. Nova Gorica) shall not be legally
responsible for any equipment damage or personal injury caused by incorrect installation or
operation other than that covered in this manual.
ⓘ Please check the Technical Specifications and Electrical Diagram chapters, as well as fuse
requirements in the Installation chapter before installing the device.
5
Page 6
Flush Shutter - Available Frequencies
EN.
ORDERING CODE
ZMNHCD1
ZMNHCD2
ZMNHCD3
ZMNHCD4
ZMNHCD5
ZMNHCD6
ZMNHCD7
ZMNHCD8
POWER SUPPLY FREQUENCY
50/60 Hz
50/60 Hz
50/60 Hz
50/60 Hz
50/60 Hz
50/60 Hz
50/60 Hz
50/60 Hz
Z-WAVE FREQUENCY*
868,4 MHz
921,4 MHz
908,4 MHz
869,0 MHz
916,0 MHz
868,4 MHz
919,8 MHz
865,2 MHz
ZMNHCD9
ZMNHCDA
ZMNHCDB
ZMNHCDC
ZMNHCDD
ZMNHCDE
50/60 Hz
50/60 Hz
50/60 Hz
50/60 Hz
50/60 Hz
50/60 Hz
922,5 MHz
919,7 – 921,7 – 923,7 MHz
868,1 MHz
868,1 MHz
919,8 MHz
920,9 MHz
*You can check the Z-Wave frequency in your country here:
http://z-wave.sigmadesigns.com/wp-content/uploads/Z-Wave_Frequency_Coverage.pdf
6
Page 7
EN.
Where To Buy
To find your nearest Qubino dealer visit: http://qubino.com/where-to-buy/
1. Introduction
The Flush Shutter controls the motors of blinds, rollers, shades, venetian blinds, etc. It
measures power consumption of the connected device, and can be paired with a digital
temperature sensor (sold separately). It supports push-button/momentary switches and toggle
switches (default).
The connection of a digital temperature sensor means you can create complex scenes and
control any device relative to a set temperature range. The Qubino Flush Shutter also acts as a
Z-Wave repeater to improve the range and stability of the Z-Wave network.
7
Page 8
Flush Shutter supported functions:
Controls position of
Controls angle of
etc.
W
kWh
Temperature
Associations
Z-Wave
Auto-inclusion
EN.
blinds, rollers, shades,
venetian blinds, etc.
blinds, venetian
blinds, vertical blinds
Measurement
Measurement
Sensor
Repeater
8
Page 9
EN.
• Remotely control outdoor venetian blinds
• Remotely control indoor venetian blinds
• Remotely control outdoor screens
• Remotely control indoor screens
2. Use Cases
The Flush Shutter can be used in many different scenes, which can help make your life more
comfortable. We have prepared a few of them for you so you can get an idea for your next
smart home project. Of course, there are countless of other options for how to use Qubino
Flush Shutter to remotely control devices via your smartphone.
2.1. Installation examples where Flush Shutter is installed behind a wall switch
9
Page 10
EN.
• Remotely control rollers
• Remotely control curtains
• Remotely control vertical window blinds
• Remotely measure room temperature
(*The temperature sensor is sold
catalogue. Product ordering code:
separately - for more info, check Qubino
ZMNHEA1
10
Page 11
2.4. Additional features of Flush Shutter which can make your life easier
• Do you know how much energy you
monitors and reports
home app (your
• Want to control other devices in your
with other
to remotely
EN.
consume?
• The Flush Shutter
energy consumption of connected devices in
real time to your smart
gateway (hub) needs to support this feature).
Know how much power your light, domestic
water tank, iron, etc, is using.
Z-Wave network with the Flush
Shutter?
• Connect the Flush Shutter
devices in your network
and automatically trigger another ZWave device. And have other Z-Wave
devices trigger your Qubino Flush
Shutter.
11
Page 12
3. Qubino Flush Shutter Advantages and Highlights
• The Qubino Flush Shutter allows the easiest and quickest installation possible. Because
of its small size, it fits smoothly in even the smallest, most shallow and most crowded
flush mounting boxes, which are stuffed with lots of electrical cables and where every
millimetre counts. All this is possible because the Qubino Flush Shutter is the smallest
Z-Wave switch in the world.
EN.
• The Qubino Flush Shutter has the option to connect a temperature sensor*, through
which users can monitor the ambient air or water temperature. It’s the only Z-Wave
switch in the worldwhich offers this option. With a connected sensor, the user can
monitor accurate measurements of the room temperature, pool water temperature,
etc., and remotely change conditions as desired. Qubino relay, along with the
temperature sensor, is connected directly to the power supply. Install it and forget it –
no need to worry about dying batteries, like with battery-powered sensors.
*The temperature sensor is sold separately - for more info, check Qubino catalogue.
Product ordering code: ZMNHEA1)
12
Page 13
EN.
• Qubino guarantees 100% device quality. Such high quality can be delivered because
every Qubino goes through rigorous quality control standards throughout the
production process. Every device has a unique serial number and a part number, which
are assigned to the device only after it goes through a strict testing procedure.
• By scanning the QR code on the back of your Qubino device, the serial and part numbers
will be automatically copied on your mobile phone; they also provide direct access to
Qubino’s technical support team. The serial and part numbers of your device are given
automatically every time you open an inquiry with our support team: this instantly
shares the relevant device information we need to provide the best technical support
possible. For details, please see the Device Information and Support chapter.
13
Page 14
EN.
• The Qubino Flush Shutter is engineered and manufactured in the EU, and contains only
the highest quality components.
• The Qubino Flush 1D Relay is certified by an independent European Institute and has CE,
FCC, LVD and EMC certificates to ensure the highest safety standards.
14
Page 15
FLUSH SHUTTER HIGHLIGHTS:
• Precise Z-Wave and manual control of motorized blinds, shades, shutters, and
sunscreens
• Allows control of venetian blinds and changing vertical position and angle of the shades
• Calibrates positioning automatically from your smart home UI and locally
• Works with push-button (momentary) and toggle switches
• Capable of measuring the power consumption of the connected device in real time via
smartphone, which allows you to save on electricity bills*
• Features one of the easiest and quickest installations of devices of this kind; fits in even
the smallest flush mounting boxes
• Saves and restores the last status after a power failure.
• Supports auto-inclusion mode for quick set up
• Supports additional parameters for expert users, which allows for advanced
configuration*
• Acts as a signal repeater which improves the range and stability of your Z-Wave network
EN.
• Can be used to remotely control and trigger other devices in your Z-Wave network
*Your gateway (hub) needs to support advanced configuration and parameter input if you wish
to use this feature
15
Page 16
4. Package Contents
• Flush Shutter Device
• Installation Manual
EN.
16
Page 17
5. Technical Terms for Switches
Symbol
Switch example images
Definition
EU
USA
Qubino
Other
names
Single pole,
single throw
(SPST) - One
switch
controlling one
light / circuit of
lights
Single pole,
double throw
(SPDT) - Two
switches
controlling the
same light /
circuit of lights
One-way
switch
Two-way
switch
Two-way
switch
(regular
switch)
Three-way
switch
Toggle
switch
Two-way
switch
EN.
Switch;
Bi-stable
switch
Used when you
have three or
more switches
controlling the
same light
After being
released, it goes
back to its
original state
Intermediate switch
Momentary switch
Four-way
switch
Intermediate switch
Momentary
switch
Crossover
switch;
Cross
connection
Monostable
switch;
Push button
17
Page 18
EN.
Qubino devices are installed into flush mounting boxes behind the switches. You can see some
examples below:
For more information on how to install your device, please refer to the Installation chapter.
18
Page 19
EN.
W
Domoticz V3.5877
✓ ✓ ✓ ✕ ✓
Fibaro HC Lite v 4.100
✓ ✓ ✓ ✓ ✓
Vera edge v 1.7.2406
o
✓ ✓
T
On UI is not
zipato
✓ ✓ ✓
T
Zwave me
✓ ✓ ✕ ✕ ✕
homeseer
✓ ✓ ✓
T
open zwave
✓ ✓ ✓
T
piper
✓ ✓ ✕ ✕ ✕
SmartThings
✓ ✓ ✓ ✓
O
Temperature
NETIChome
✓ ✓ ✓ ✓ ✓
homey
T T T T T T
eedomus
✓ ✓ ✓ ✕ ✓
jeedom
✓ ✓ ✓ ✓ ✓
Symbol
Explanation
Works fully
Not working
O
See comment
T
Testing in progress
6. Compatibility with Z-Wave Gateways (hubs)
Please check compatibility with your Z-Wave gateway (hub) before you purchase this device. If
you don’t see your gateway (hub) in the table below, please contact us at:
http://qubino.com/support/#email.
Flush shutter
Tilt
✓
✓
✓
✓
✓
✓
✕
✓
Q1
✓
Q2
kWh
Temp Comments
✓
displayed
actual value
of tilts when
use stop level
change or
when
changed with
input
switches
✓
✓
✓
sensor
support
added in the
future
✓
✓
✓
✓
✕
19
Page 20
EN.
7. Installation
Before installing the device, please read the following carefully and follow the instructions
exactly:
ⓘ Danger of electrocution!
Installation of this device requires a great degree of skill and may be performed only by a
licensed and qualified electrician. Please keep in mind that even when the device is turned off,
voltage may still be present in the device’s terminals.
ⓘ Note!
Do not connect the device to loads exceeding the recommended values. Connect the device
exactly as shown in the provided diagrams. Improper wiring may be dangerous and result in
equipment damage.
Electrical installation must be protected by directly associated overcurrent protection fuse
4A, gG or Time lag T, rated breaking capacity 1500A (ESKA 522.723) must be used according to
wiring diagram to achieve appropriate overload protection of the device. The fuse must be
installed in fuse holder type: Adele contact 503Si/1 DS according to the standard IEC60669-2-
1. This standard is used in Europe only.
20
Page 21
EN.
7.1. Installing the device behind a light switch
The installation process, tested and approved by professional electricians, consists of the
following simple steps:
Step 1 – Turn OFF the fuse:
• To prevent electrical shock and/or equipment damage, disconnect electrical power at
the main fuse or circuit breaker before installation and maintenance.
• Be aware that even if the circuit breaker is off, some voltage may remain in the wires —
before proceeding with the installation, be sure no voltage is present in the wiring.
• Take extra precautions to avoid accidentally turning the device on during installation.
21
Page 22
Step 2 – Installing the device:
• Connect the device exactly according to the diagrams shown below
Before Qubino installation:
EN.
22
Page 23
After Qubino installation:
EN.
23
Page 24
EN.
ⓘ Note!
• Place the antenna as far as possible from metal elements as they may cause signal
interference.
• Do not shorten the antenna.
The device’s antenna should be as upright as possible. This ensures the device’s operational
range is maximized (up to 98 feet (30 m) line of sight).
24
Page 25
Step 3 – Add the device to your Z-Wave network:
• For more details on how to include the device, please refer to the Z-Wave Inclusion
chapter.
EN.
25
Page 26
Step 4 – Turn ON the fuse:
EN.
Step 5 – The Installation is now complete. It’s time to make your life more comfortable with
the help of the Qubino Flush Shutter
26
Page 27
EN.
7.2. Installing the Qubino Temperature Sensor
The temperature sensor is a Qubino accessory and is sold separately - for more info, please
see the Qubino product catalogue or website: http://qubino.com/products/accessories/
Product ordering code: ZMNHEA1
Qubino Z-Wave modules have the option to connect a temperature sensor (sold separately),
which allows you to remotely monitor ambient or water temperature. Qubino modules are the
only Z-Wave devices of its kind to offer this unique capability. With the sensor connected to the
module, you can carry out accurate measurements of room temperature, pool water
temperature, etc. and build automation rules around them. Qubino module with a temperature
sensor is connected directly to power supply. Install it and forget it, there is no need to worry
about changing the batteries like with most other Z-Wave temperature sensors which run on
batteries. The temperature sensor’s range is between -50° and 125°C (-58° - 257° F).
The digital Temperature sensor comes with a 1 m (3.3 ft) cord and a connector to attach it
1. To prevent electrical shock, make sure that no voltage is present on the temperature
sensor cable.
2. When connected to Qubino module, the temperature sensor is under high voltage,
which is very dangerous.
3. Goap d.o.o. does not take responsibility for any damage or electrical shock due to
incorrect sensor assembly.
4. The above instructions and description apply to a temperature sensor compatible with
Qubino products only.
directly to a Qubino module.
27
Page 28
Temperature sensor installation example:
Step 1 – Exclude the device (if it is already connected to your Z-Wave system)
EN.
28
Page 29
Step 2 – Switch of the power supply
EN.
Step 3 – Connect the temperature sensor as shown below
29
Page 30
Step 4: Place the temperature sensor in the switch box
EN.
30
Page 31
Step 5 – Turn the fuse on
EN.
Step 6 – Re-include the device to your network
31
Page 32
Step 7 – Start using the temperature sensor in connection with your device
EN.
32
Page 33
EN.
8. Device Information and Support
Did you know that Qubino offers Z-Wave devices with 100% quality control guaranteed
throughout the production process? Every single unit is tested and examined before being
approved for sale – a truly unique pledge in the industry.
Why is this important?
Every device has a dedicated a serial number and a part number, which is assigned to the
device only after it goes through a strict testing procedure.
By scanning the QR code on the back of your Qubino, its device title, serial number, and part
number are automatically copied to your mobile phone. You can also use the code for direct
access to the device page for more information. If you still don’t find what you’re looking for,
click on the link to Qubino technical support team. They will be able to automatically read the
serial and part number from your device and quickly review the production log file containing
the production date as well as any relevant device parameters and information. This process
allows our team to immediately identify and address issues, giving you the best support
possible.
Based on customer and business partner feedback, we’re proud to boast Qubino’s support
team as the best and fastest on the market. If you don't find the answers to your questions in
this document, please contact our support team by scanning the QR code on your device or
through our website: http://qubino.com/support/#email. We will try to help you as soon as
possible.
33
Page 34
9. Electrical Diagram (110 - 230VAC, 24VDC)
N
Neutral wire (+VDC)
L
Live (line) wire (-VDC)
Q1⬆
Output for motor UP (open)
Q2⬆
Output for motor DOWN (close)
I2
Input for switch/push button DOWN (close)
I1
Input for switch/push button UP (open)
TS
Temperature sensor terminal
S
Service button
EN.
Notes for diagram:
WARNING:
The S (Service) button must NOT be used when the device is connected to a 110-230V power supply.
The durability of the device depends on the applied load. For resistive loads (light bulbs, etc.) and 4A current
consumption of each individual electrical device, the product’s lifespan exceeds 70,000 toggles.
OVER CURRENT PROTECTION
When the current exceeds 4A, relay is automatically turned off and “Over-current detected” Notification will also
be sent to the gateway. To reactivate the module, the power supply has to be turned OFF and ON again.
34
Page 35
EN.
10. Adding the device to a Z-Wave network (Inclusion)
AUTOMATICALLY ADDING THE DEVICE TO A Z-WAVE NETWORK (AUTO INCLUSION)
1. Enable add/remove mode on your Z-Wave gateway (hub)
2. Connect the device to the power supply (with the temperature sensor already connected –
sold separately*).
3. Auto-inclusion will be initiated within 5 seconds of connection to the power supply and the
device will automatically enroll in your network
MANUALLY ADDING THE DEVICE TO A Z-WAVE NETWORK (MANUAL INCLUSION)
1. Enable add/remove mode on your Z-Wave gateway (hub)
2. Connect the device to the power supply (with the temperature sensor already connected*)
3. Toggle the switch connected to the I1 terminal 3 times within 3 seconds
OR
If the device is powered by 24 V SELV supply, press and hold the S (Service) button for at least 2
seconds
4. A new multi-channel device will appear on your dashboard
*If connecting the temperature sensor, switch off the power supply and make sure the device
is excluded from your network BEFORE connecting the sensor.
ⓘ Make sure the device is excluded from your network before connecting the temperature
sensor. Switch off the power supply, connect the temperature sensor, and re-include the device
to your network.
35
Page 36
EN.
11. Removing the device from a Z-Wave network
(Exclusion)
REMOVAL FROM A ZWAVE NETWORK (Z-WAVE EXCLUSION)
1. Connect the device to the power supply
2. Make sure the device is within direct range of your Z-Wave gateway (hub) or use a handheld Z-Wave remote to perform exclusion
3. Enable add/remove mode on your Z-Wave gateway (hub)
4. Toggle the switch connected to the I1 terminal 3 times within 3 seconds
OR
If the device is powered by 24 V SELV supply, press and hold the S (Service) button for 2 to 6
seconds
5. The device will be removed from your network but any custom configuration parameters
will not be erased
FACTORY RESET
1. Connect the device to the power supply
2. Within the first minute the device is connected to the power supply, toggle the switch
connected to the I1 terminal 5 times within 3 seconds
OR
If the device is powered by 24 V SELV supply, press and hold the S (Service) button for at least 6
seconds
ⓘ By resetting the device, all custom parameters previously set on the device will return to
their default values, and the owner ID will be deleted. Use this reset procedure only when the
main gateway (hub) is missing or otherwise inoperable.
36
Page 37
EN.
12. Associations
Use associations for direct communication between the Flush Shutter and other devices within
your Z-Wave network without the need of your primary gateway (hub).
Association Groups:
Root device:
• Group 1: Lifeline group (reserved for communication with the primary controller), 1
node allowed.
• Group 2: Basic on/off (status change report for I1 input) up to 16 nodes.
• Group 3: Basic on/off (status change report for I2 input) up to 16 nodes.
• Group 4: Basic on/off (status change report for sensing roller moving: up=FF, down=0)
up to 16 nodes.
• Group 5: Basic on/off (status change report at reaching roller position: bottom=FF,
top=0) up to 16 nodes.
• Group 6: Basic on/off (status change report at reaching roller position: bottom=FF, not
bottom=0) up to 16 nodes
• Group 7: Multilevel set (status change report for Flush Shutter position), up to 16 nodes.
• Group 8: Multilevel sensor report (external temperature sensor report – sensor sold
separately), up to 16 nodes.
End point 1:
• Group 1: Lifeline group, 0 nodes allowed.
• Group 2: Basic on/off (status change report for I1 input), up to 16 nodes.
• Group 3: Basic on/off report (status change report for I2 input), up to 16 nodes.
• Group 4: Basic on/off (status change report for sensing roller moving: up=FF, down=0)
up to 16 nodes.
• Group 5: Basic on/off (status change report at reaching roller position: bottom=FF,
top=0) up to 16 nodes.
• Group 6: Basic on/off (status change report at reaching roller position: bottom=FF, not
bottom=0) up to 16 nodes
• Group 7: Multilevel set (status change report for Flush Shutter position), up to 16 nodes.
End point 2:
• Group 1: Lifeline group, 0 nodes allowed.
• Group 2: Multilevel set (status change report slats tilting position), up to 16 nodes.
37
Page 38
End point 3 (External Temperature Sensor):
• Group 1: Lifeline group, 0 nodes allowed.
• Group 2: Multilevel sensor report (external temperature sensor report – sensor sold
separately), up to 16 nodes.
EN.
38
Page 39
EN.
13. Flush Shutter Calibration
Automatic calibration
Automatic calibration is a process during which the Flush Shutter learns the position of the limit
switches.
Shutter positioning calibration
(par. 71 set to 0)
There are two options to calibrate the device:
• Calibration through the main controller UI
1) Include the module into the Z-Wave network according to the instructions for inclusion.
2) Set the parameter 78 (Forced Flush Shutter calibration) value to 1.
3) Flush Shutter performs the calibration process, completing full cycle - up, down and up
again.
4) Set the parameter 78 (Forced Flush Shutter calibration) value to 0.
• Calibration through the inputs I1 and I2
1) Include the module into the wireless network according to the instructions for inclusion.
2) Quick press the switch/push-button connected to I1 input and wait until the Shutter
reaches the upper limit switch.
3) Quick press the switch/push-button connected to I2 input and wait until the Shutter
reaches the lower limit switch.
4) Quick press the switch/push-button connected to I1 input and wait until the Shutter
reaches the upper limit switch.
Slates tilting position calibration
(par. 71 set to 1)
When enabling venetian blinds mode, position calibration for slats titling must be done. After
doing this, the position and angle of the slates can be set. By default, full turn time for slates is
set to 1.5s. This value can be changed with parameter 72.
39
Page 40
EN.
1) Include and perform the module calibration process according to section ‘Shutter positioning
calibration’.
2) Set parameter 71 to 1 ‘Venetian blinds’.
3) Exclude the module (without reset!).
4) Include the module.
5) After the module will be included, another widget (besides the main Shutter widget) for
slates control will appear on the UI.
6) By default full turn movement is set to 1.5s. If this time is too long (if after slates full cycle the
Shutter starts moving up or down), decrease this time with the parameter 72. If this time is too
short (if the slats will not turn for a full cycle), increase this time with the parameter 72.
Manual operation for Shutter
(par. 71 set to 0)
The user can connect a push-button (mono-stable) or a switch (bi-stable) to I1 and I2 terminals.
Pressing the push-button for less than 2 seconds, which is connected to I1 (up), initiates up
movement.
Pressing the push-button for less than 2 seconds, which is connected to I2 (down), initiates
down movement.
If the Shutter is moving, any press (of any push-button) will stop the movement.
Keeping the push-button, connected to I1 (up), pressed for more than 2 seconds initiates up
movement, until the push-button is released.
Keeping the push-button, connected to I2 (down), pressed for more than 2 seconds, initiates
down movement, until the push-button is released.
Manual operation for venetian blinds
(par. 71 set to 1)
Slates on start position - 0 degree
Clicking the push-button (for time < full turn slates time-par.72) connected to I1 (up), initiates
slates turning towards end - 180 degree position, until push-button is released.
40
Page 41
EN.
Clicking the push-button (for time < full turn slates time-par.72) connected to I2 (down),
initiates Shutter down movement.
If the Shutter is moving, any click (of any push-button), will stop the movement.
Keeping the push-button pressed (for time > full turn slates time-par.72) connected to I1 (up),
initiates full slates turn and up movement, until the push-button is released.
Keeping the push-button pressed (for time > full turn slates time-par.72) connected to I2
(down), initiates Shutter down movement, until the push-button is released.
Keeping the push-button pressed (for time > (full turn slates time +2s)) connected to I1 (up),
initiates up movement, until the push-button is released.
Slates on end position - 180 degree
Clicking the push-button (for time < full turn slates time-par.72) connected to I1 (up), initiates
Shutter up movement.
Clicking the push-button (for time < full turn slates time-par.72) connected to I2 (down),
initiates slates turning towards start - 0 degree position, until the push-button is released.
If the Shutter is moving, any click (of any push-button), will stop the movement.
Keeping the push-button (for time > full turn slates time-par.72), connected to I1 (up), pressed,
initiates the Shutter up movement, until the push-button is released.
Keeping the push-button (for time > full turn slates time-par.72), connected to I2 (down),
pressed, initiates full slates turn and down movement, until the push-button is released.
Keeping the push-button (for time > (full turn slates time +2s)), connected to I2 (down),
pressed, initiates down movement, until push-button is released.
41
Page 42
EN.
14. Configuration Parameters
Parameter no. 10 - Activate / deactivate ALL ON / ALL OFF Functionality
Flush Shutter module responds to the commands ALL ON / ALL OFF that may be sent by the
primary or secondary controller within the Z-Wave network.
Values (size is 2 byte dec):
• default value 255
• 255 - ALL ON active, ALL OFF active.
• 0 - ALL ON not active, ALL OFF not active
• 1 - ALL ON not active, ALL OFF active
• 2 - ALL ON active, ALL OFF not active
Parameter no. 40 – Watt Power Consumption Reporting Threshold for Q1 or Q2 Loads
Choose by how much the power consumption needs to increase or decrease to be reported.
Values correspond to percentages, so if 10 is set (by default), the module will report any power
consumption changes of 10% or more, compared to the last reading.
Values (size is 1 byte dec):
• default value 10
• 0 - Power consumption reporting disabled
• 1 - 100 = 1% - 100% Power consumption reporting enabled. New value is reported only
when the power consumption in real time changes by more than the percentage value
set in this parameter, compared to the previous power consumption reading, starting at
1% (the lowest value possible).
42
Page 43
EN.
NOTE: Power consumption needs to increase or decrease by at least 1 Watt to be reported,
REGARDLESS of the percentage set in this parameter.
Parameter no. 42 – Power reporting in Watts by time interval for Q1 or Q2
The set value refers to the time interval with which the power consumption in Watts is
reported (0 – 32535 seconds). If 0 is entered (by default), energy consumption reports will not
be sent to the controller.
Values (size is 2 byte dec):
• default value 300
• 0 - Power consumption reporting disabled
• 1 – 32767 = 1 - 32767 seconds. Power consumption reporting enabled. Report is sent
according to time interval (value) set here.
Parameter no. 71 – Operating modes
Choose between the two operating modes. If the venetian mode is selected, an additional
widget/endpoint will be displayed on the UI interface, which can be used to control the tilt
position of the slats. If the Shutter mode is selected, this additional endpoint is hidden.
Values (data type is 1 byte dec):
• default value 0
• 0 - Shutter mode
• 1 - venetian mode (up/down and slate rotation)
43
Page 44
EN.
NOTE1: After the value of this parameter is changed, first exclude module (without setting
parameters to their default values), wait at least 30s and then reinclude the module!
Parameter no. 72 – Slats tilting full turn time
Set the time, required by the slats, to make a full turn (180 degrees).
Values (data type is 2 byte dec):
• default value 150 = 1.5 seconds
• 0 - tilting time disabled
• 1 - 32767 = 0,01seconds – 327.67 seconds
NOTE: If the set time is too long and a full turn was already performed, the device will start to
move up or down for the remaining time.
44
Page 45
EN.
Parameter no. 73 – Slats position
Choose the position of the slats after up/down movement (activated through the Z-Wave
controller or the push-buttons) is completed.
Values (data type is 1 byte dec):
• default value 1
• 0 - Slats return to the previously set position only after being activated via the Z-Wave
controller (not valid for limit switch positions).
• 1 - Slats return to the previously set position in case they were activated via the Z-Wave
controller, push-button operation or when the lower limit switch is reached.
Parameter no. 74 – Motor moving up/down time
This parameter defines the time, required by the Shutter motor, to completely open or
completely close the attached shutters.
Values (data type is 2 byte dec):
• default value 0
• 0 – moving time disabled (working with limit switches)
• 1 - 32767 = 0.1seconds – 3276.7 seconds
After the set time passes, the motor stops (relay goes to the off state).
NOTE: It is important that the reference position, for setting the moving time, is always when
the Shutter is at its lowest position!
Set parameter 74 to 0 and move the Shutter (using the up/down push-buttons or the main
controller UI) to the lowest desired position. When the Shutter reaches this position, set the
parameter 74 to the duration, required by the Shutter, to completely open or completely close
45
Page 46
EN.
the attached shutters. At this point the Shutter can be moved up (open), but can't be moved
down, because this position is already set as its lowest position.
To change the defined lowest position of the Shutter below the one, which is already defined
(manual recalibration), the parameter 74 must be set to 0 and the procedure, which is
described above, should be repeated.
In case the Shutter operates using limit switches, but the user still wants to control the
opening/closing position with time, this is still possible. If a time duration, which is longer than
the opening/closing time of the shutters in real time (limited by the limit switches), is set, the
Shutter will stop at the limit switches, but the module relay will switch it off after a defined
time, not by the limit switch of the Shutter. Take into consideration that in this condition,
positioning the shutters with the slider (through the UI) will not display the correct position of
the Shutter.
Parameter no. 76 - Motor operation detection
Define the power consumption threshold at the end positions. Based on this value, the device
will know, that the shutters reached the limit switches.
Values (data type is 1 byte dec):
• default value 30 = 30W
• 0 - 127 = 1-127 W. The value 0 means that reaching a limit switch will not be detected.
46
Page 47
EN.
Parameter no. 78 - Forced Shutter calibration
By changing the value of this parameter from 0 to 1, the Shutter enters the calibration mode.
For further information about the calibration process, please see section 9.
Values (data type is 1 byte dec):
• default value 0
• 1 - Start the calibration process. When the calibration process finishes
(completing the full cycle - up, down and up again), set the value of the
parameter 78 (Forced Shutter calibration) back to 0.
Parameter no. 85 – Power consumption max delay time
Define the maximum time before the power consumption of the motor, after one of the relays
is switched ON, is read from the device. If there is no power consumption during the set time
(motor not connected, damaged or requires longer time to start, motor at the end position),
the relay will switch OFF. This time is defined by entering it manually.
47
Page 48
Values (data type is 1 byte dec):
• default value 30 = 3s
• 0 = time is set automatically
• 3 - 50 = 0.3seconds - 5seconds (100ms resolution)
EN.
Parameter no. 90 – Time delay for next motor movement
This parameter defines the minimum time duration between successive motor movements
(minimum time after which the motor is switched off and on again).
Values (data type is 1 byte dec):
• default value 5 = 500ms
• 1 - 30 = 0.1seconds - 3seconds (100ms resolution)
48
Page 49
EN.
Parameter no. 110 – Temperature Sensor Offset Settings
Set value is added to or subtracted from the actually measured value to adjust the temperature
report sent by an external sensor (sold separately). This parameter only applies to the degrees
temperature unit (the Fahrenheit unit is currently not supported).
Values (size is 2 byte dec):
• default value 32536
• 32536 - Offset is 0 degrees.
• 1 - 100 - Where 1 stands for 0.1 and 100 stands for 10.00 degrees added to the actual
measurement.
• 1001 - 1100 – Where 1001 stands for -0.1 degrees and 1100 stands for -10.0 degrees
subtracted from the actual measurement.
Parameter no. 120 – Temperature Sensor Reporting Threshold
If an external digital temperature sensor (sold separately) is connected to the module, it reports
temperature readings based on the threshold defined in this parameter. This parameter only
applies to the degrees temperature unit (the Fahrenheit unit is currently not supported).
Values (size is 1 byte dec):
• Default value 5 = 0.5°C
• 0 – Reporting disabled
1 - 127 = Where 1 stands for 0.1 and 127 stands for 12.7 degrees
49
Page 50
15. Technical Specifications
Power supply
110 - 230 VAC ±10% 50/60Hz, (24-30VDC)
Rated load current of AC/DC output
2 X 4A / 230VAC / 30VDC
Output circuit power of AC/DC
2 X 920W (230VAC) /
Power measurement accuracy
P=0-200W, +/-2W
Digital temperature sensor range
-50 ~ +125°C (-58 ~ 257°F)
Operation temperature
-10 ~ +40°C (-14 ~ 104°F)
Z-Wave operation range
up to 30 m indoors (98 ft)
41,8x36,8x16,9 mm (79x52x22 mm) / 1,65x1,45x0,66 in
Weight (with package)
28g (34g) / 0.97oz (1.20oz)
Electricity consumption
0,4W
For installation in boxes
Ø ≥ 60 mm (2,36 in) or 2M (78,74 in),
Switching
Relay (2x)
Z-Wave Repeater
Yes
(resistive load) *
EN.
output (resistive load)
Dimensions (WxHxD) (package)
2 X 96W (24VDC)
P>200W, +/-3%
(3,11x2,05x0,87 in)
depth≥ 60 mm (2,36 in)
* In case of loads other than resistive loads, please pay attention to the value of cos φ. If
necessary, connect loads less powerful than what they’re rated for – this applies to all motor
loads. Max current for cos φ=0,4 is 2A at 250VAC, 3A at 24VDC.
50
Page 51
Supported loads
Electric motor
400W (230VAC)
EN.
200W (110VAC)
For power factor = 0,4
In case of inductive loads it is recommended to use RC
snubber circuit.
51
Page 52
16. Z-Wave Command Classes
COMMAND_CLASS_ZWAVEPLUS_INFO_V2,
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1
COMMAND_CLASS_POWERLEVEL_V1
COMMAND_CLASS_SECURITY
Securely Supported Command Classes:
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_SWITCH_ALL_V1
COMMAND_CLASS_SWITCH_BINARY_V1
EN.
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
COMMAND_CLASS_METER_V4
COMMAND_CLASS_SENSOR_MULTILEVEl_V7
COMMAND_CLASS_NOTIFICATION_V5
COMMAND_CLASS_MULTI_CHANNEL_V4
COMMAND_CLASS_ASSOCIATION_2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2
COMMAND_CLASS_CONFIGURATION_V1
COMMAND_CLASS_MARK
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
Endpoint1:
Device Class:
BASIC_TYPE_ROUTING_SLAVE
GENERIC_TYPE_SWITCH_MULTILEVEL
52
Page 53
SPECIFIC_TYPE_CLASS_C_MOTOR_CONTROL
Command Classes:
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SWITCH_ALL_V1
COMMAND_CLASS_SWITCH_BINARY_V1
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
COMMAND_CLASS_METER_V4
COMMAND_CLASS_NOTIFICATION_V5
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
EN.
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2
COMMAND_CLASS_MARK
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
Endpoint2:
Device Class:
BASIC_TYPE_ROUTING_SLAVE
GENERIC_TYPE_SWITCH_MULTILEVEL
SPECIFIC_TYPE_CLASS_C_MOTOR_CONTROL
Command Classes:
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SWITCH_ALL
COMMAND_CLASS_SWITCH_BINARY_V1
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
COMMAND_CLASS_ASSOCIATION_V2
53
Page 54
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2
COMMAND_CLASS_MARK
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
Endpoint 3:
Device Class:
GENERIC_TYPE_SENSOR_MULTILEVEL
SPECIFIC_TYPE_ROUTING_SENSOR_MULTILEVEL
Command Classes:
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_SECURITY
EN.
COMMAND_CLASS_SENSOR_MULTILEVEL_V7
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2
NOTE: The Endpoint 3 command class list only applies if an external digital temperature sensor
(sold separately) is connected to the TS terminal. If the sensor is not connected, the following
command class is not supported by the device:
COMMAND_CLASS_SENSOR_MULTILEVEL_V7
This product can be included and operated in any Z-Wave network with other Z-Wave certified
devices from any other manufacturers. All constantly powered nodes in the same network will
act as repeaters regardless of the vendor in order to increase reliability of the network. Security
Enabled Z-Wave Controller must be used in order to fully utilize the product.
54
Page 55
EN.
17. Important Disclaimer
Z-Wave wireless communication is not always 100% reliable. This device should not be used in
situations in which life and/or valuables are solely dependent on its functioning. If the device is
not recognized by your gateway (hub) or shows up incorrectly, you may need to change the
device type manually and make sure your gateway (hub) supports multi-channel devices.
Contact us for help before returning the device: http://qubino.com/support/#email
18. Warning
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection
facilities. Contact your local government for information regarding the collection systems
available. If electrical appliances are disposed of in landfills or dumps, hazardous substances
can leak into the groundwater and get into the food chain, damaging your health and wellbeing. When replacing old appliances with new ones, the retailer is legally obligated to take
back your old appliance for disposal free of charge.
19. Regulations
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radi-ate radio frequency energy and, if not in-stalled and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures: —Reorient or relocate the receiving antenna. —
Increase the separation between the equipment and receiver. —Connect the equipment into
an outlet on a circuit different from that to which the receiver is connected. —Consult the
dealer or an experienced radio/ TV technician for help.
55
Page 56
EN.
Legal Notice
This user manual is subject to change and improvement without notice. GOAP d.o.o. Nova
Gorica reserves all rights to revise and update all documentation without any obligation to
notify any individual or entity.
Declaration of Conformity
Qubino Flush Shutter device is in compliance with the essential requirements and other
relevant provisions of the Low voltage (LVD) Directive (2014/35/EU), Electromagnetic
Compatibility (EMC) Directive (2014/30/EU), Radio Equipment Directive (2014/53/EU), Directive
RoHS (2011/65/EU) and Directive ErP (2009/125/EC).
WEEE
According to the WEEE (Waste electrical and electronic equipment) Directive, do not dispose of
this product as household waste or commercial waste. Waste electrical and electronic
equipment should be appropriately collected and recycled as required by practices established
for your country. For information on recycling of this product, please contact your local
authorities, your household waste disposal service or the shop where you purchased the
product.
NOTE: User manual is valid for device with SW version S5 (SW version is part of P/N)!
Example:P/N: ZMNHCDxHxS5Px
Goap d.o.o. Nova Gorica
Ulica Klementa Juga 007, 5250 Solkan, Slovenia
E-mail: info@qubino.com
Tel: +386 5 335 95 00
Web: www.qubino.com
Date: 27.10.2017; V 1.5.1
DON’T MISS OTHER INVENTIONS FROM QUBINO– CLICK HERE AND CHECK OUT QUBINO’S
COMPLETE PORTFOLIO
56
Loading...