ZIP HydroTap® G4 Celsius
User Guide
• |
Tap Operation.................. |
(Pages 3-5) |
|
• |
LCD Screen & Menu ....... |
(Pages 6-19) |
|
• |
Maintenance.................... |
(Pages 20-23) |
|
• |
Contact & Details............ |
(Page |
24) |
• |
Date of Installation............. |
/......... |
/......... |
ARC CUBE
Affix Model Number Label
Here 802698
802698 - G4 User Guide - 09.16 - v2.02 |
Page 1 of 24 |
NOTES
Page 2 of 24 |
802698 - G4 User Guide - 09.16 - v2.02 |
Tap operation - Chilled Sparkling
Turning the rotary control allows the dispensing of either Chilled Sparkling or Chilled water. For your convenience, the rotary control is spring loaded, so when released, will return automatically to the OFF position
To dispense Sparkling water: (Model CSHA)
Turn the rotary control forward as shown
Rotate for Sparkling water
Tap operation - Chilled water
To dispense Chilled water: (Model CHA)
Turn the rotary control in reverse as shown
Rotate for Chilled water
802698 - G4 User Guide - 09.16 - v2.02 |
Page 3 of 24 |
Tap operation - Boiling water
To dispense Boiling water: with the safety ON.
Tapping the illuminated RED safety button twice, with one finger, will cause the safety red light to flash for a few seconds. While flashing, turn the rotary control (as shown) to dispense boiling water.
(See section G for safety settings)
Rotate for Boiling water
Safety
To dispense Boiling water: with the safety OFF.
When the RED safety light is OFF, turn the rotary control (as shown) to dispense boiling water.
Tap operation - Mixer
The Mixer tap lever is operated as a conventional ‘Flick Mixer’. The hot side is marked with a red stripe and the cold side with a blue stripe, for dispensing cold to warm water.
Lifting the handle up will decrease the flow rate and lowering the handle will increase the flow rate. Lift the handle all the way up to turn the tap off.
When the handle is moved towards the blue mark, the temperature is decreased and when moved towards the red mark, the temperature is increased. The final temperature will be dependant on the temperature of the incoming cold water.
The spout may be swivelled, left or right, through 170° for convenience.
Vent
Boiling models
Page 4 of 24 |
802698 - G4 User Guide - 09.16 - v2.02 |
Filter Warning and Reset
Temperature Warning Light:
The warning light will flash slowly for 1 sec On and 3 secs OFF whenever the water is not at the temperature set point. The tap may be operated, but the water may not be at the desired temperature . The slow flashing light will turn off once the water reaches the set point. The set point temperature is user adjustable (See section G).
Filter Warning Light:
As a reminder that the filter requires changing, the warning light will flash quickly every 10 secs. (See section on filter maintenance.)
Filter Reset:
The warning light will need to be reset after the filter has been changed. (See section C)
Fault Warning Lights:
If there is a fault with the system, both the safety light and the warning light will flash for 1/2 sec ON and 1/2 sec OFF until the fault is rectified.
(See section B) or call an authorised service man.
Warning light
Safety light
Sleep mode (Boiling models)
In SLEEP MODE the unit will Go to “Sleep” after 2 hrs of inactivity, after which, the home screen status window will show “Sleep Mode”.
The sleep mode may be activated from the settings menu. (See section G).
To wake from sleep mode, first tap the safety twice and then turn the rotary control.
802698 - G4 User Guide - 09.16 - v2.02 |
Page 5 of 24 |
3LCD Screen
The Zip HydroTap G4 Celsius introduces a ‘TOUCH’ screen for easy setup and operation adjustment.
Safety lock Icon |
Sleep Mode Icon |
Energy Mode Icon |
BHA window
Set boiling water temperature |
Filter usage |
**Status window
CHA window
Set chilled water temp.
Date and Time
CSHA window
Other possible messages in status window:
Status** |
Information |
Notes |
System Fault |
Product has one or more system |
Refer to section B |
|
faults |
|
Change Filter |
External/Internal filter needs to be |
Refer to section C |
|
replaced |
|
NOTE: As an energy saving feature, the home screen will turn OFF After 5 minutes of non use. Touching the darkened LCD panel will reactivate the home screen.
Page 6 of 24 |
802698 - G4 User Guide - 09.16 - v2.02 |
3LCD Screen Menu
Main Menu |
|
Sub Menu |
|
Sub Menu Options |
Section |
|||
|
|
|
|
|
|
|
|
|
Language |
• |
English |
|
|
|
A |
||
• |
German |
|
|
|
||||
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
• |
Product Info |
• |
Product serial no. |
B |
||
|
|
• |
System Faults |
|||||
Information |
• |
Lists |
|
|||||
|
|
• |
Event Log |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
• |
Filter Flush |
• |
Reset options |
C |
||
Installation |
• |
Filter Reset |
• |
Calibration options |
||||
|
|
|
|
|
|
|
|
|
Service |
|
Password protected |
|
|
|
D |
||
|
|
|
|
|
|
|
||
Security |
• |
Enable Password |
• |
Set Password |
E |
|||
• |
Change Password |
|||||||
|
|
|||||||
|
|
|
|
|
|
|
|
|
Communication |
• |
Remote Monitor |
• |
Wifi |
Options |
F |
||
• |
Remote Control |
• |
Wifi |
Options |
||||
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
• |
12hr/24hr Mode |
|
|
|
• |
Date/Time |
• |
Hot/Cold Setpoint |
|
|
|
• |
Temperature |
• |
Filter Life (Litres) |
|
|
Settings |
• |
Filter |
• |
Filter Life (Months) |
G |
|
• |
Energy Modes |
• |
Sleep Mode Options |
|||
|
|
|||||
|
• |
Safety |
• |
Safety Lock |
|
|
|
• |
Dispense Times |
• |
Hot/Cold |
|
|
|
|
|
|
Dispensing |
|
802698 - G4 User Guide - 09.16 - v2.02 |
Page 7 of 24 |
LCD Screen operation - Section A A Set Language
1. Press [MENU] for main menu.
2. Press [Language] button.
3. Select the preferred language
4. Press [<=] button for the previous menu
LCD Screen operation - Section B B System Information
In this section, you can find your product serial number , check system fault messages or view the event logs of your product.
1. Press the [MENU] button for main menu.
2. Press the [Info] button to view the product serial number and other key information
1. Press [Product Info] to view the product serial no.
2. Press [<=] button for the previous menu or press [Home] button to return to the home screen.
1. Press [System Faults] to check the fault information;
2. Press [<=] button for the previous menu or press
[Home] button to return to the home screen.
Press [Filtert Log] to view the system’s filter log.
1. Press [<=] button for the previous menu or press
[Home] button to return to the home screen.
Page 8 of 24 |
802698 - G4 User Guide - 09.16 - v2.02 |