Zephyr ADLE42BSX User Manual

Layers Island

ALL-M90BBX
ALL-M90BWX
ALL-E42BBX
ALL-E42BWX

Duo Island

www.zephyronline.com

ADL-M90BSX
ADL-E42BSX

RANGE HOOD - Installation and use instructions

ENGLISH........................................3

FRANÇAIS...................................29

- 2 -

Table of contents

Safety Instructions.............................................. Page 4 - 5

List of Materials.................................................. Page 6 - 7

Ducting Calculation Sheet.................................... Page 8

Hood Specifications............................................. Page 9 - 10

Wiring Diagram.................................................... Page 11

Cleaning and Maintenance.................................... Page 12

Remote Control....................................................Page 13

Hood Controls......................................................Page 14 - 15

nstallation

Internal Blower................................................ Page 16 - 18

External and In-Line Blower.............................Page 19 - 21

Range Hood....................................................Page 22 - 23

Non-Ducted Recirculation Kit............................Page 23

Duct Covers....................................................Page 24

Mesh Filters....................................................Page 25

List of Parts & Accessories.................................. Page 26

Warranty.............................................................Page 27

- 3 -

READ AND SAVE THESE INSTRUCTIONS

!

INTENDED FOR DOMESTIC COOKING ONLY

!

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the
manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel to
prevent power from being switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all
applicable codes and standards, including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s
guidelines and safety standards such as those published by the National Fire Protection Associa­tion (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. To reduce the risk of fire, use only metal ductwork.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk
of electrical shock by providing an escape wire for the electric current.

WARNING - Improper grounding can result in a risk of electric shock.
Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt

exists as to whether the appliance is properly grounded.

WARNING - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette,
Cherries Jubilee, Peppercorn Beef Flambe’).

3. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for the size of the surface element.

5. Keep fan, filters and grease laden surface clean.

6. Use high range setting on range only when necessary. Heat oil slowly on low to medium setting.

7. Don’t leave range unattended when cooking.

8. Always use cookware and utensils appropriate for the type and amount of food being prepared.

- 4 -

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE
FIRE, OBSERVE THE FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE
CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL
THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you already know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.

!

CAUTION

1. For indoor use only.

2. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust

air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

3. Take care when using cleaning agents or detergents.

4. Avoid using food products that produce flames under the Range Hood.

5. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and

vapors.

6. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray,

construction dust, etc. off power unit.

7. Your hood motor has a thermal overload which will automatically shut off the motor if it becomes

overheated. The motor will restart when it cools down. If the motor continues to shut off and restart,
have the hood serviced.

8. For best capture of cooking impurities, the bottom of the hood should be no less than 24" above the

cooking surface.

9. Two installers are recommended because of the large size and weight of this hood.

10. This product is equipped with a thermostat which may start blower automatically. To reduce the

risk of injury and to prevent power from being switched on accidentally, switch power off at service
panel and lock or tag service panel.

11. Please read specification label on product for further information and requirements.

12. To reduce risk of fire and electric shock, install this range hood only with Internal Blower Model

CBI-290A or CBI-600A, Exterior Blower Model CBE-1000 or In-Line Blower Model PBN-1000A,
(manufactured by Pacific Kitchen). Other blowers cannot be substituited. (Blower sold separately).

- 5 -

LIST OF MATERIALS

Layers

- Zephyr blower sold separately

- Non-ducted recirculating kit sold separately

Duct Cover Assembly
Remote Blower Collar with

Damper (External motor)

Remote Blower Wiring
Harness

Remote Blower Wiring Extension

Remote Blower Box Cover

Remote Blower Box

Electrical System Box

Hardware Packet

Box Cover (box

marked “120 VAC

Input”)

Box marked “120

VAC Input”

Glass

Led

Mesh Filter

- 6 -

LIST OF MATERIALS

Duo

- Zephyr blower sold separately

- Non-ducted recirculating kit sold separately

Duct Cover Assembly

Remote Blower Collar with
Damper (External motor)

Remote Blower Wiring
Harness

Remote Blower Wiring Extension

Remote Blower Box Cover

Remote Blower Box

Electrical System Box

Hardware Packet

Box Cover (box

marked “120 VAC

Input”)

Box marked “120

VAC Input”

Led

Mesh Filter

- 7 -

DUCTING CALCULATION SHEET

Maximum Duct Length:
For satisfactory air movement, the total duct length
should not exceed 100 equivalent feet.

- 8 -

HOOD SPECIFICATIONS

Layers

- 9 -

HOOD SPECIFICATIONS

Duo

- 10 -

WIRING DIAGRAM

- 11 -

CLEANING AND MAINTENANCE

Proper maintenance of the Range Hood will assure proper performance of the unit.

Motor

The motor is permanently lubricated and never needs oiling. If the motor bearings make
excessive or unusual noise, replace the motor with the exact service motor. The impeller
should also be replaced.

Mesh Filters

The mesh filters should be cleaned frequently. Using warm water with detergent. Mesh
filters are dishwasher safe.

Clean all-mesh filters in the dishwasher using a non-phosphate detergent. Discoloration
of the filter may occur if using phosphate detergents, or as a result of local water
conditions - but this will not affect filter performance. This discoloration is not covered by
the warranty. See “MESH FILTERS” section for removal and installation instructions.

Non-ducted Charcoal Filter

The non-ducted charcoal filter should be changed every 6 months or when prompted on
the hood controls. Replace more often if your cooking style generates extra grease, such
as frying and wok cooking. See “MESH FILTERS” section for removal and installation
instructions.

LED Lighting

In the unlikely event that your LED strip fails, please contact Zephyr to order
replacement parts and schedule service.

Stainless Steel Cleaning
DO:

• Regularly wash with clean cloth or rag

soaked with warm water and mild soap or
liquid dish detergent.

• Always clean in the direction of original

polish lines.

• Always rinse well with clear water (2 or 3

times) after cleaning. Wipe dry completely.

• You may also use a specialized

household stainless steel cleaner.

Avoid: When choosing a detergent

• Any cleaners that contain bleach will attack stainless steel

• Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.

• Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc.,

are highly explosive and should never be used close to a range.

DON’T:

• Use any steel or stainless steel wool or
any other scrapers to remove stubborn dirt.

• Use any harsh or abrasive cleansers.

• Allow dirt to accumulate.

• Let plaster dust or any other construction
residues reach the hood. During
construction/renovation, cover the range
hood to make sure no dust sticks to the
stainless steel surface.

- 12 -

REMOTE CONTROL

SYNCHRONIZATION:

To synchronize the remote control with the range hood for the first time, proceed as
follows:

1. With the range hood off, press and hold the “Power” and “Delay Off” buttons on theremote for

4 seconds (Fig. 1a) until the “Delay Off” indicator on the hood illuminates (Fig.1b).

2. Press the “Delay Off” button on the hood within 4 seconds to confirm the link (Fig. 2).If

successful, the “Delay Off” indicator will blink 3 times. The range hood is now syncrhonized
with the remote control. If you experience anyproblems, repeat the procedure.

FCC Caution: To assure continued compliance, any changes or modifi cations not expressly approved
by the party responsible for compliance could void the user’s authority to operate this equipment.
(Example - use only shielded interface cables when connecting to computer or peripheral device. This
device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1)
This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.

GENERAL INFORMATION:

- Remove any protective film from the remote surface prior to using it.

- The remote control has a range of approximately 10-15 feet.

- The remote control is equipped with a magnetic base and may be attached to ferrous

surface for easy storage.

- The remote top is made of a plastic material and is prone to scratches.

Use care when handling and cleaning the remote; we suggest using a microfiber cloth to
clean it.

- The remote control will enter a sleep mode after 20 seconds of inactivity to conserve

battery life. Press any button for one second to wake the remote.

BATTERY REPLACEMENT:

The batteries will last approximately 8 months, depending on usage.

1. Remove rubber cover from bottom (Fig.3).

2.Using an object such as a screwdriver or pen, gently place it in the center opening in

the bottom of the remote and push inwards to dislodge the top touch panel from the
remote body. (Fig. 4)

3. Press on the metal spring located in the battery tray to dislodge battery. Replace both

batteries with type 3V CR2450 (Fig.5). Re-assemble by following instructions in reverse.

3 54

- 13 -

CONTROLS

E

A

A: Power button

- Power Button will turn power on and off for the entire hood (fan and lights).

- Hood will remember the last speed and light level it was last turned off at.(Example:

hood is turned off at when it was last on high speed and high lights; hood will turn back
on at high speed and high lights when Power Button is pressed).

B: Fan Speed button

- From off, press once for low speed (1), twice for medium (2), and three times for high (3).

- Fan should cycle through speeds low (1), medium (2), and high (3) continuously.

C: Light button

- Lights are three level (high, medium, low).

- From off, touch once for high.

- From off, touch twice for medium.

- From off, touch three times for low.

- From off, touch four times to cycle back to off.

- Light level will cycle from high, medium, low, off.

D: Delay off button

- Press this button to enable the five minute delay-off function. After five minutes the fan

and lights will power off.

- If the fan is already on (example high speed) the fan will change to low speed when the

Delay Off Button is pressed and turn off after five minutes.

- When the Delay Off Function is on, the user can still change the fan speed by pressing

the Fan Speed Button without interrupting the five minute Delay Off Timer.

- Delay Off Function can be turned off by pressing Delay Off Function button or Power

Button.

B

H I

G

F

C D

G: Light indicator

- Light indicator will turn on when lights are turned on at any light level.

H: Filter clean and charcoal filter replace indicator

-

Mesh filter clean (always enabled):

- Filter Clean Indicator will illuminate after 30 hours of fan usage indicating it is time to

clean the mesh filter. Indicator light will remain illuminated, it will not blink.

- This function must be reset by the user. With hood off, hold the Fan Speed Button for

five seconds, after five seconds the Filter Clean Indicator will turn off and the 30 hour
timer will reset.

-

Charcoal filter replace (disabled by default, must be enabled by user if recirculating hood):

- To enable Charcoal Filter Replacement Function:

- With hood off, hold Fan Speed and Delay Off buttons simultaneously for 5 seconds.

Filter Clean Indicator will quickly flash 3 times indicating the Charcoal Filter Replacement
Function is enabled. Filter Clean Indicator will continuously blink after 120 hours of unit

- 14 -

fan usage indicating it is time to replace the charcoal filter. Indicator light will blink, it will
not remain illuminated.

- This function must be reset by the user. With hood off, hold the Delay Off Button for five

seconds, after five seconds the Filter Clean Indicator will stop blinking and turn off and
the 120 hour timer will reset.
Order replacement charcoal filter kit number Z0F-01AC through your local dealer,
www.zephyronline.com or the Zephyr customer service department.

- To disable Charcoal Filter Replacement Function:

- With hood off, hold Fan Speed and Delay Off buttons simultaneously for 5 seconds.

Filter Clean Indicator will illuminate for 3 second then turn off indicating the Charcoal
Filter Replacement Function is disabled.

I: Delay off indicator

- Delay Off Indicator will light up when Delay Off Function is activated by pressing the

Delay Off Button.

- Delay Off Indicator will turn off after the Delay Off Function has completed the five

minute cycle or if the user presses the Delay Off Button again or the Power Button.

E: Clean air indicator

- Clean Air Indicator is disabled by default and must be enabled by the user.

- To enable Clean Air Function:

- With hood off, hold the Power Button down for five seconds. Clean Air Indicator light will

illuminate, and the fan will turn on low speed for 10 minutes. After 10 minutes the fan will
turn off and the 4 hour timer will begin. Clean Air Indicator will remain on when Clean Air
Function is enabled, even if fan is not on. When Clean Air Function is enabled, every four
hours of non fan usage the fan will automatically turn on at low speed for 10 minutes.
After 10 minutes the fan will turn off and the 4 hour timer will reset. When the Clean Air
Function automatically turns the fan on the Clean Air Indicator will blink and the Low
Speed fan indicator will illuminate. If the user changes the fan speed while the Clean Air
Function is operating, the Clean Air Indicator will stop blinking but will remain illuminated.
When the user manually turns the hood off the 4 hour timer will reset.

- To disable Clean Air Function:

- With hood off, hold Power Button down for five seconds until Clean Air Indicator light

turns off.
Note1: Changing the fan speed and interrupting the Clean Air Function while it is
operating does not disable the Clean Air Function. Clean Air Function will only be
disabled by holding the Power Button for 5 seconds.
Note 2: Turning lights on/off does not disable the Clean Air Function.

F: Fan Speed indicator

- 1 = Low

- 2 = Medium

- 3 = High

- On speed low, only number 1 indicator will be on.

- On speed medium, 1 and 2 indicator will be on.

- On speed high, 1, 2 and 3 indicators will be on.

- When fan off, no fan speed indicator will be on.

LED LIGHT STRIP

If the LED is damaged, it must be replaced only by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.

- 15 -

INSTALLING THE DUCTWORK:
INTERNAL BLOWER

NOTE: To reduce the risk of fire, use only
metal ductwork.

1. Decide where the ductwork will run
between the hood and the outside.

2. A straight, short duct run using a minimum
6” round duct will allow the hood to perform
most efficiently.

3. Long duct runs, elbows, and transitions will
reduce the performance of the hood. Use
as few of them as possible.

4. Install a roof cap. Connect round metal
ductwork to cap and work back towards
hood location. Use duct tape to seal the
joints between ductwork sections (Fig.7).

DUCT COVER

HOOD

ROOF CAP

24” MINIMUM

ABOVE COOKING

SURFACE

6” ROUND DUCT

FIG. 7

- 16 -

INSTALLING THE INTERNAL
BLOWER

NOTE: The following instructions are for
installing the internal blower only.
Install this range hood only with internal blower
model CBI-290A or CBI-600A.

1. Remove the 6” metallic flange provided on
the blower’s air outlet (the flange may
already be pre-installed) (Fig.8).

2. Remove the blower plate unscrewing the
(4) 3.9x9.5 mm screws (Fig.9).

3. Install internal blower into blower plate and
secure using (4) screws (Fig.10).

4. Install assembly blower by means (8) 3.9x6
mm screws (Fig.11).

5. Place the 6” metallic flange provided on the
blower’s air outlet (Fig.12).

MOUNTING
SCREWS

3.9x6mm

FIG. 8

MOUNTING
SCREWS

3.9x6mm

FIG. 9

(4) MOUNTING
SCREWS
(Supplied with the
motor)

FIG. 11

FIG. 10

FIG. 12

- 17 -