WASHING MACHINE
FJ 1054 W
FJ 1254 W
FJ 1354 S
FJ 1454 W
JETSYSTEM |
1200 |
|
F |
|
TE |
132994360 |
INSTRUCTION BOOKLET |
GB |
Important Safety Information
It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings.
These warnings have been provided in the interest of safety. You MUST read them carefully before installing or using the appliance.
Installation
●This appliance is heavy. Care should be taken when moving it.
●It is dangerous to alter the specifications or attempt to modify this product in any way.
●All packing and transit bolts must be removed before use. Serious damage can occur to the product and to property if this is not adhered to. See relevant section in instructions.
●Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person.
●Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person.
●Care must be taken to ensure that the appliance does not stand on the electrical supply cable.
●If the machine is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely.
Child Safety
●This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the product.
●Pets and children have been known to climb into washing machines. Please check your drum before use.
●The glass door becomes very hot during the washing cycle. Keep children away from the vicinity of the appliance whilst it is in operation.
●Keep all packaging well away from children.
●Keep all detergents in a safe place out of children’s reach.
Use
●Always unplug the appliance and turn off the water supply after use.
●Do not overload the appliance. See relevant section in the instruction book.
●Only wash fabrics which are designed to be machine washed. If in doubt, consult the care label on the clothes.
●Before washing, ensure that all pockets are empty and buttons and zips are fastened. Avoid washing frayed or torn articles and treat stains such as paint, ink, rust, and grass before washing. Underwired bras must NOT be machine washed.
●Any objects such as coins, safety pins, nails, screws, stones or any other hard, sharp material can cause extensive damage and must not be placed into the machine.
●Garments which have been in contact with volatile petroleum products should not be machine washed. If volatile cleaning fluids are used, care should be taken to ensure that the fluid is removed from the garment before placing in the machine.
●Wash small items such as socks, laces, washable belts etc in a washing bag or pillow case as it is possible for such items to slip down between the tub and the inner drum.
●Only use the advised quantities of fabric softener. Damage to the fabric can ensue if you over-fill. Refer to the manufacturer’s recommendations of quantities.
●As some duvets and eiderdowns should be washed in large commercial machines because of their bulk, please check with the manufacturer of the item before washing in a domestic machine.
●Leave the porthole door slightly ajar between washes to preserve the door seal.
●Under no circumstances should you attempt to repair the machine yourself. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local Zanussi Service Force Centre. Always insist on genuine Zanussi spare parts.
2
Contents
For the User
Important Safety Information |
2 |
Your New Washing Machine |
4 |
Description of the Appliance |
5 |
Door locked light |
5 |
Detergent dispenser drawer |
5 |
Child safety feature |
5 |
The Control Panel |
6-8 |
Turning the acoustic signal off |
6 |
Operating sequence |
9-11 |
Load the laundry |
9 |
Measure out the detergent |
9 |
Measure out the fabric softener |
9 |
Switch the machine on |
9 |
Select the required programme/fabric |
9 |
Select the temperature |
9 |
Select the spin speed or the RINSE HOLD option |
10 |
Select the desired options |
10 |
Start the programme |
10 |
How to change a programme during its cycle |
10 |
How to cancel a programme during its cycle |
10 |
How to open the door during the cycle of |
|
a programme |
10 |
End of programme |
11 |
Washing Hints |
12-13 |
Which detergent?.... |
13 |
And in which form? |
13 |
Wash Care Symbols |
14 |
Washing Programmes |
15 |
Maintenance and Cleaning |
16-17 |
Descaling |
16 |
After each wash |
16 |
Maintenance Wash |
16 |
External cleaning |
16 |
Cleaning the dispenser drawer |
16 |
Cleaning the drawer recess |
16 |
Cleaning the filter |
16-17 |
The dangers of freezing |
17 |
Something Not Working |
18-19 |
Guarantee Conditions |
20 |
For the Installer
Installation Instructions |
21 |
Technical Specifications |
21 |
Unpacking |
22 |
Positioning |
22 |
Water inlet |
23 |
Water drainage |
23-24 |
Levelling |
24 |
Special conditions |
24 |
In the interest of the environment |
24 |
Electrical connection |
25 |
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions
Hints and tips Environmental information
3
Your New Washing Machine
Your new washing machine, fitted with the Zanussi “JET SYSTEM”, meets all modern requirements for effective treatment of laundry with low water, energy and detergent consumption.
Even small loads are washed “economically” because the amount of water used is regulated automatically according to the load and type of fabric.
●Automatic cooling of the wash water to 60°C before draining, with the 90°C programme. This reduces thermal shock to fabrics, helping to prevent creasing.
●The special wool programme with its new delicate wash system treats your woollens with extreme care.
●The anti-unbalance device ensures that the washing machine remains stable when spinning.
Ecological hints
To save water and energy and help protect the environment, we recommend that you follow these hints:
●Normally soiled laundry may be washed without prewashing in order to save detergent, water and time (the environment is protected too!).
●The machine works more economically if it is fully loaded.
●With adequate pre-treatment, stains and limited soiling can be removed; the laundry can then be washed at a lower temperature.
●Measure out detergent according to the water hardness, the degree of soiling and the quantity of laundry being washed.
In the interest of the environment
●Materials marked with the symbol are recyclable.
●Check with your local Council or Environmental Health Office to see if there are facilities in your area for re-cycling this appliance.
●When the appliance is to be scrapped, cut off the power supply cable and make the door lock device unusable to prevent young children from being trapped inside.
●Help to keep your country tidy - use authorised disposal sites for your old appliance.
How do we help to protect the environment? We use recycled paper!
Important
Your machine is fitted with a balance control device, which ensures the machine is stable during the spin.
If the wash load appears not to have been spun sufficiently at the end of the wash cycle, because it is not evenly distributed in the drum, the balance control device may have operated. It will therefore be necessary to redistribute the wash load manually and select a spin programme. For more detailed information see the section headed “Something Not Working”.
4
Description of the Appliance
1Detergent dispenser drawer
2Control panel
3Door locked light
4Door opening handle
5Filter
6Adjustable feet
Door locked light
1 |
|
|
|
2 |
JETSYSTEM |
1200 |
|
|
|
|
FF |
|
|
|
|
|
T |
S |
S |
|
F |
EMP |
PIN |
OP |
|
|
|
|
3 |
|
|
|
|
4 |
|
|
|
|
5 |
|
6 |
|
|
|
It stays on during the whole programme indicating that the door is locked.
When the light goes out, the door can be opened (see pages 10-11).
Detergent dispenser drawer
Prewash
Main wash
Fabric softener
Child safety feature
This machine incorporates a special child safety feature to prevent small children from being trapped inside the machine.
To activate this device, rotate the button (without pressing it) inside the door clockwise until the groove is horizontal. If necessary use a coin.
To disable this device and restore the possibility of closing the door, rotate the button anti-clockwise until the groove is vertical.
C0063 |
P1131 |
5
The Control Panel
N/O |
|
O |
FF |
COTTONS |
90°C |
1200 |
PREWASH |
SYNTHETICS |
60°C |
900 |
AA40° |
DELICATES |
50°C |
700 |
|
WOOL |
40°C |
500 |
|
|
30°C |
RINSE |
QUICK |
|
|
HOLD |
|
|
|
T |
|
|
E |
|
|
|
|
|
|
|
|
E |
|
|
|
|
|
E |
O |
|
|
|
|
M |
|
R |
S |
|
|
S |
|||
|
|
|
|
|
|
ED |
|
||||
F |
S |
|
U |
|
PI |
P |
|
PTION |
|||
|
PERAT |
|
|
|
N S |
|
|
|
|||
ABRIC |
|
|
|
|
|
|
|
|
|
|
FJ 1254 W
|
|
SKIP |
|
|
|
|
T |
ST |
SE |
SE |
|
RE |
|
||
|
ART/PAU |
|
|
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
1 ON/OFF button
Press this button to switch the washing machine on. Press the ON/OFF button again to switch the machine off.
2 MAINS-ON light
This light is connected to the ON/OFF button. It lights up when you press the button, and goes out when you press it again.
3 FABRICS button
Press this button repeatedly to select the programme on the basis of the type of laundry to be washed. The light relevant to the selected programme will light up. The washing machine will propose a temperature and automatically select the maximum spin value provided for the programme you have chosen. You can change these values by operating buttons 4 and 5.
4 TEMPERATURE button
Press this button repeatedly to increase or decrease the temperature, if you want your laundry to be washed at a temperature different from the one proposed by the washing machine.The relevant light will light up. Maximum temperatures are 90°C for cotton, 60°C for synthetic fabrics, 40°C for delicate fabrics and wool.
IMPORTANT!
By pressing the TEMPERATURE and SPIN SPEED buttons simultaneously, the acoustic signal is deactivated at the end of the cycle, when selecting the programmes and in case of an incorrect option selection .
By pressing these 2 buttons again the acoustic signal is reactivated.
5 SPIN SPEED button
Press this button repeatedly to change the spin speed, if you want your laundry to be spun at a speed different from the one proposed by the washing machine. The relevant light will light up.
Maximum speeds are:
•for cotton: 1400, 1300, 1200 or 1000 rpm depending on the model;
•for synthetic fabrics and wool: 900 rpm;
•for delicate fabrics: 700 rpm.
RINSE HOLD position : when you choose this option, the machine will not drain the water of the last rinse, so as not to wrinkle the laundry.
At the end of the cycle, the START/PAUSE button light will flash, to indicate that the water must be drained. To complete the cycle, choose one of the following options:
•Draining and spin:
-Press the START/PAUSE button. The machine will drain the water, then spin the laundry at the maximum speed provided for the selected programme.
-Select spin speed by means of button 5, and press the START/PAUSE button.
•Drain only
-Press the SKIP/RESET button once, so as to cause
the DRAIN light to light up, then press the START/PAUSE button.
Important! If you accidentally press the SKIP/RESET button more than once the programme is cancelled., To drain the water, select any washing programme by means of the FABRIC button, then press SKIP/RESET three times in order to select the DRAIN position (only the DRAIN light will remain lit).
6
6 OPTIONS button
Press this button to select the following options:
•PREWASH: select this option if you wish your laundry to be prewashed before the main wash (not available for wool).
The prewash ends with a short spin at 650 rpm in programmes for cotton and synthetic fabrics, whereas in the programme for delicate fabrics the water is only drained.
•AA 40°: this option can be selected for cottons and synthetics lightly or normally soiled with a temperature of 40°C and higher.
If you select 40°C , the machine will prolong the time at 40°C in the washing phase, this will allow an A class in energy efficiency and washing performance to be achieved.
If you select 90°C and press the AA 40° button, the washing temperature will be reduced from 90°C to 60°C.
If you select 60°C or 50°C and press the AA 40° button, the washing temperature will be reduced to 40°C. In both cases the washing time will be prolonged.
•QUICK: select this option for laundry that is only slightly soiled.
The washing time will be reduced according to the type of fabric and the selected temperature.
The PREWASH, the QUICK and AA 40°options cannot be selected together.
Important!
The first time you use the washing machine, when you switch it on, it may give an audible warning signal. This is due to the fact that the washing machine has performed a washing cycle during the manufacturer’s inspection tests, and this cycle has not been erased after its completion.
7 START/PAUSE button
This button has three functions:
•Start: after you have selected the desired programme and options, press this button to start the washing machine. The light above the button will stop flashing and remain lit.
•Pause: when you press this button again, the programme in progress is interrupted. The light above the button will start flashing. To restart the programme, press the button again.
When you PAUSE the cycle, the DOOR LOCKED light goes out, and it becomes possible to open the door, provided
•the washing machine is not in the heating phase beyond 55°C;
•the level of the water is not high;
•the drum is not turning.
Important! You must set the washing machine to PAUSE before you make any change in the programme in progress.
•Draining of water and spinning after the execution of programmes with the RINSE HOLD option.
8 SKIP/RESET button
This button performs two functions:
-Clears the memory
-Selects special programmes
At the end of every programme the SKIP/RESET button must be pressed once or repeatedly to clear the programme memory. All the lights must be off.
If the previous programme is not cleared, an audible signal will sound, when you switch the machine on.
7
Selecting a special programme:
A wash programme must be selected in the normal way. (START button not pressed)
ST |
S |
|
|
ART/PAU |
E |
|
|
To select Drain, press the SKIP button three times, the wash - rinses - spin LED,s go out.
PREWASH
WASH
RINSES
RINSE HOLD
SPIN
DRAIN
FILTER
END
A normal wash cycle consists of the following phases, Wash - Rinses - Spin and is confirmed by the illumination of the corresponding LED,s.
PREWASH
WASH
RINSES
RINSE HOLD
SPIN
DRAIN
FILTER
END
To select rinses & spin, press the SKIP button once, the wash LED goes out.
PREWASH
WASH
RINSES
RINSE HOLD
SPIN
DRAIN
FILTER
END
To select spin only, press the SKIP button twice. The wash & rinses LED,s go out.
PREWASH
WASH
RINSES
RINSE HOLD
SPIN
DRAIN
FILTER
END
If you wish to cancel or advance the running programme to the required phase, PAUSE the cycle and then press the SKIP button as previously described.
12 Programme phase indicator lights
When you select a programme, the lights relevant to the phases that form the programme light up.
PREWASH
WASH
RINSES
RINSE HOLD
SPIN
DRAIN
FILTER
END
After you have started the programme, only the light relevant to the phase that is currently being carried out will remain lit.
At the end of the programme the pilot light illuminates.
If the light lights up at the end of the programme this means that the drain filter is clogged.
In the event of operating problems the light of the START/PAUSE button and one of the following lights start to flash:
= the machine does not fill
= the machine does not empty
= the door has not been closed
To eliminate the problem, see paragraph “Something not working”.
8