York H-RC018, H-RC036S, 060 User Manual

TECHNICAL GUIDE

SPLIT-SYSTEM

AIR CONDITIONERS

12 SEER

MODELS: H*RC018 THRU 060

(1.5 THRU 5 NOMINAL TONS, 1 PH)

H*RC036S(25,46) THRU 060

(3 THRU 5 NOMINAL TONS, 3 PH)

E D

T O

A R I

I

AS

TIF

ER

C

C

O

R

AI

R-

MP

L

TU

R

E

R

CON

Y

I

A

ITI

N

C

UN

N

A

I

W

F

N

I

U

G

T

N

H

A

M

R

C

E

T

OF

E

Q U I P M EN

RT

IF I

S

ION

A R I

CA T I ON

S ECT

210

S T

A N DAR D

CERTIFICATION APPLIES ONLY

WHEN THE COMPLETE

SYSTEM IS LISTED

WITH ARI.

	ISO 9001
LISTED	Certified Quality
	Management System

Due to continuous product improvement, specifications are subject to change without notice.

Visit us on the web at www.york.com for the most up-to-date technical information.

Additional rating information can be found at www.ariprimenet.org.

036-21137-004 Rev. C (0505)

DESCRIPTION

The 12 SEER Series condensing unit is the outdoor part of a versatile system of air conditioning. It is designed to be cus- tom-matched with one of UPG’s complete line of evaporator sections, each designed to serve a specific function. Matching Air Handlers are available for upflow, downflow or horizontal applications to provide a complete system. Electric Heaters are available if required. Add-On coils are available for use with upflow, downflow or horizontal furnaces and air handlers.

WARRANTY

Single Phase Units:

5-year limited parts warranty.

10-year limited compressor warranty.

Three Phase Units:

1-year limited parts warranty.

5-year limited compressor warranty.

FEATURES

•QUALITY CONDENSER COILS - The coil is constructed of enhanced copper tube and aluminum fins.

•COIL PROTECTION - Coils are protected from damage by a polymer mesh applied between the coil face, and a PVC coated steel coil guard.

•PROTECTED COMPRESSOR - The compressor is internally protected against high pressure and temperature. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protects the compressor if undesirable operating conditions occur. A liquid line filter-drier further protects the compressor.

•DURABLE FINISH - The cabinet is made of pre-painted steel. The pre-treated galvanized steel provides a better paint to steel bond, which resists corrosion and rust creep. Special primer formulas and matted textured champagne finish insure less fading when exposed to sunlight.

•LOWER INSTALLED COST - Installation time and costs are reduced by easy power and control wiring connections. Discharge line heat exchanger knockouts are provided, if required. Available in sweat connect models only. The unit contains enough refrigerant for matching indoor coils and 15 feet of interconnecting piping. The small base dimension means less space is required on the ground or roof.

•TOP DISCHARGE - The warm air from the top mounted fan is blown up away from the structure and any landscaping. This allows compact location on multi-unit applications.

•LOW OPERATING SOUND LEVEL - The upward air flow carries the normal operating noise up away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the rippled fins of the condenser coil muffle the normal fan motor and compressor operating sounds.

•LOW MAINTENANCE - Long life permanently lubricated motor-bearings need no annual servicing.

•EASY SERVICE ACCESS - Fully exposed refrigerant connections, a single panel covering the electrical controls and the molex plug in the control box connecting the condenser fan, make for easy servicing of the unit.

•SECURED SERVICE VALVES - Secured re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging.

•U.L. and C.U.L. listed - approved for outdoor application.

Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240.

FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

036-21137-004 Rev. C (0505)

Physical and Electrical Data - 1 Phase

MODEL				H2RC018S06	H2RC024S06	H2RC030S06		H2RC036S06		H2RC042S06	H2RC048S06	H4RC060S06
Unit Supply Voltage							208/230 – 1 – 60
Normal Voltage Range								187 to 252
Minimum Circuit Ampacity1				10.1	14.1	16.5		19.7		26.2	28.5	37.5
Max. Overcurrent Device Amps 2				15	25	25		30		45	50	60
Compressor Type3				Recip	Inertia	Recip		Recip		ScrollB	Recip	ScrollB
Compressor Amps			Rated Load	7.7	10.9	12.8		14.7		19.9	21.8	28.8
			Locked Rotor	48	60	68		82		115	105	145
Crankcase Heater				No	No	No		Yes		No	No	No
Fan Motor Amps			Rated Load	0.5	0.5	0.5		1.3		1.3	1.3	1.5
Fan Diameter Inches				18	18	22		22		22	22	22
			Rated HP	1/12	1/12	1/15		1/4		1/4	1/4	1/4
Fan Motor
			Nominal RPM	1,100	1,100	850		850		850	850	850
			Nominal CFM	2,000	2,000	2,300		3,300		3,300	3,300	3,450
		Face Area Sq. Ft.		12.58	12.58	15.72		15.72		17.03	19.65	23.58
Coil
		Rows Deep		1	1	1		1		1	1	1
		Fin / Inches		18	18	18		18		18	18	22
Liquid Line OD				3/8	3/8	3/8		3/8		3/8	3/8	3/8
Vapor Line OD				3/4	3/4	3/4		3/4		7/8	7/8	1-1/8
Unit Charge (Lbs. - Oz.) 4				4 - 9	4 - 7	5 - 8		5 - 3		6 - 13	7 - 7	8 - 15
Charge Per Foot, Oz.				0.68	0.68	0.68		0.68		0.70	0.70	0.76
Operating Weight Lbs.				144	146	156		161		157	190	198

PHYSICAL AND ELECTRICAL DATA - 3 Phase

MODEL				H1RC036S25		H1RC048S25	H1RC060S25			H1RC036S46	H1RC048S46	H1RC060S46
Unit Supply Voltage						208/230 – 3 – 60					460 - 3 - 60
Normal Voltage Range 1						187 to 252					432 to 504
Minimum Circuit Ampacity				13.3		18.9		22.9		7.6	9.6	12.0
Max. Overcurrent Device Amps 2				20		30		40		15	15	20
Compressor Type				Inertia		Inertia		Scroll		Inertia	Inertia	Scroll
Compressor Amps			Rated Load	9.6		14.1		17.3		5.4	7.0	9.0
			Locked Rotor	78.0		130.0		123.0		40.0	64.0	62.0
Crankcase Heater				No		No		No		No	No	No
Fan Motor Amps			Rated Load	1.3		1.3		1.3		0.8	0.8	0.8
Fan Diameter Inches				22		22		22		22	22	22
			Rated HP	1/4		1/4		1/4		1/4	1/4	1/4
Fan Motor			Nominal RPM	850		850		850		850	850	850
			Nominal CFM	3,300		3,300		3,400		3,300	3,300	3,400
		Face Area Sq. Ft.		15.72		17.03		23.58		15.72	17.03	23.58
Coil		Rows Deep		1		1		1		1	1	1
		Fin / Inches		18		18		18		18	18	18
Liquid Line OD				3/8		3/8		3/8		3/8	3/8	3/8
Vapor Line OD				3/4		7/8		1-1/8		3/4	7/8	1-1/8
Unit Charge (Lbs. - Oz.) 4				6 - 2		7 - 10		9 - 3		6 - 2	7 - 10	9 - 3
Charge Per Foot, Oz.				0.68		0.70		0.76		0.68	0.70	0.76
Operating Weight Lbs.				157		184		198		157	184	198

1.Rated in accordance with ARI Standard 110, utilization range “A”.

2.Dual element fuses or HACR circuit breaker.

3.All scrolls listed with a superscript “B” are Bristol scrolls. All scrolls listed with a superscript “C” are Copeland scrolls.

4.The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value.

2	Unitary Products Group

036-21137-004 Rev. C (0505)

Additional R-22 Charge / Orifice Size for Various Matched Systems - 1 Phase

	Outdoor Unit		H2RC018S06	H2RC024S06	H2RC030S06	H2RC036S06	H2RC042S06	H2RC048S06	H4RC060S06
	Unit Orifice (s)1		53	59	63	73	78	87	–
	Factory R-22 Charge, lbs-oz.		4 - 9	4 - 7	5 - 8	5 - 3	6 - 13	7 - 7	8 - 15
	Indoor Coil5	Coil Orifice4			Orifice or TXV	Kit 2 - Additional	Charge, Oz.3
	G2FD024(S,H)14,17	61	53 + 3	59 + 3	–	–	–	–	–
			701 + 3	701 + 3	–	–	–	–	–
	G2FD030(S,H)17	65	53 + 6	59 + 6	63 + 4	–	–	–	–
			701 + 6	701 + 6	701 + 4	–	–	–	–
	G2FD035(S,H)14	65	53 + 6	59 + 6	63 + 4	73 + 0	–	–	–
			701 + 6	701 + 6	701 + 4	702 + 0	–	–	–
	G2FD036(S,H)17	75	–	59 + 10	63 + 8	73 + 6	–	–	–
			–	701 + 10	701 + 8	702 + 6	–	–	–
	G2FD036(S,H)21	75	–	–	63 + 11	73 + 8	–	–	–
			–	–	701 + 11	702 + 8	–	–	–
	G2FD042(S,H)21	78	–	–	63 + 14	73 + 12	78 + 0	–	–
			–	–	701 + 14	702 + 12	702 + 0	–	–
	G2FD046(S,H)17	78	–	–	63 + 16	73 + 12	78 + 0	87 + 0	–
			–	–	701 + 16	702 + 12	702 + 0	703 + 0	–
	G2FD048(S,H)21,24	84	–	–	–	73 + 16	78 + 10	87 + 11	–
			–	–	–	702 + 16	702 + 10	703 + 11	–
	G2FD060(S,H)24	90	–	–	–	–	–	87 + 15	–
			–	–	–	–	–	703 + 15	703 + 5
	G2FD061H24	90	–	–	–	–	–	87 + 19	–
			–	–	–	–	–	703 + 19	703 + 11
	G1HA024H14	61	053 + 03	059 + 03	–	–	–	–	–
	G1HA024H14(T)	TXV 701	+ 03	+ 03	–	–	–	–	–
	G1HA036H14	75	–	59 + 12	63 + 11	73 + 08	–	–	–
	G1HA036H14(T)	TXV 702	–	–	+ 11	+ 08	–	–	–
	G1HA036H17	78	–	–	63 + 14	73 + 12	–	–	–
	G1HA036H17(T)	TXV 702	–	–	+ 14	+ 12	–	–	–
	G1HA048H21	84	–	–	–	73 + 09	78 + 07	87 + 08
	G1HA048H21(T)	TXV 703	–	–	–	+ 09	+ 07	+ 08
	G1HA060H24	90	–	–	–	–	–	87 + 15
	G1HA060H24(T)	TXV 703	–	–	–	–	–	87 + 15	703 + 5
	G1HD024	59	53 + 5	59 + 4	–	–	–	–	–
			701 + 5	701 + 4	–	–	–	–	–
	G1HD036	69	–	59 + 13	63 + 11	73 + 7	–	–	–
			–	701 + 13	701 + 11	702 + 7	–	–	–
	G1HD048	81	–	–	–	73 + 13	78 + 3	87 + 4	–
			–	–	–	702 + 13	702 + 3	703 + 4	–
	G1HD060	93	–	–	–	–	–	87 + 12	–
			–	–	–	–	–	703 + 12	703 + 0
	G1FA/G1UA024S14,17(T)	59	53 + 0	59 + 0	–	–	–	–	–
			7015 + 0	701 + 0	–		–	–	–
	G1FA/G1UA030S14(T)	65	–	59 + 3	63 + 0	–	–	–	–
			–	701 + 3	701 + 0	–	–	–	–
	G1FA/G1UA036S14(T)	73	–	59 + 8	63 + 6	73 + 3	–	–	–
			–	701 + 8	701 + 6	702 + 3	–	–	–
	G1FA/G1UA036S17,21(T)	73	–	59 + 6	63 + 4	73 + 0	–	–	–
			–	701 + 6	701 + 4	702 + 0	–	–	–
	G1FA/G1UA048S17(T)	84	–	–	63 + 16	73 + 13	78 + 0	87 + 0	–
			–	–	701 + 16	702 + 13	702 + 0	703 + 0	–
	G1FA/G1UA048S21(T)	84	–	–	63 + 18	73 + 9	78 + 7	87 + 8	–
			–	–	701 + 18	702 + 9	702 + 7	703 + 8	–
	G1FA/G1UA060S21,24(T)	90	–	–	–	–	78 + 16	87 + 15	–
			–	–	–	–	702 + 16	703 + 15	703 + 5
	G1NA030S17K	63	53 + 6	59 + 6	63 + 4	–	–	–	–
			701 + 6	701 + 6	701 + 4	–	–	–	–
	G1NA030S21M	78	53 + 6	59 + 6	63 + 4	–	–	–	–
			701 + 6	701 + 6	701 + 4	–	–	–	–
	See notes on Page 4.

Unitary Products Group

3

036-21137-004 Rev. C (0505)

Additional R-22 Charge / Orifice Size for Various Matched Systems (Continued)- 1 Phase

	Outdoor Unit		H2RC018S06	H2RC024S06	H2RC030S06	H2RC036S06	H2RC042S06	H2RC048S06	H4RC060S06
	Unit Orifice (s)1		53	59	63	73	78	87	–
	Factory R-22 Charge, lbs-oz.		4 - 9	4 - 7	5 - 8	5 - 3	6 - 13	7 - 7	8 - 15
	Indoor Coil5	Coil Orifice4			Orifice or TXV	Kit 2 - Additional	Charge, Oz.3
	G1NA036S17L	63	–	–	63 + 15	73 + 12	–	–	–
			–	–	701 + 15	702 + 12	–	–	–
	G1NA048S21D	78	–	–	–	73 + 12	78 + 0	87 + 0	–
			–	–	–	702 + 12	702 + 0	703 + 0	–
	G1NA048S24P	63	–	–	–	73 + 13	78 + 2	87 + 1	–
			–	–	–	702 + 13	702 + 2	703 + 1	–
	G1NA060S24T	78	–	–	–	–	–	–	–
			–	–	–	–	–	–	703 + 0
	G1NF024SOF	63	–	–	–	–	–	–	–
			–	–	–	–	–	–	–
	G1NF036SOF	67	–	59 + 12	63 + 0	73 + 7	–	–	–
			–	701 + 12	701 + 0	702 + 7	–	–	–
	G1NF048SOF	78	–	–	–	–	78 + 21	87 + 6	–
			–	–	–	–	702 + 21	703 + 6	–
	G1NF060SOF	87	–	–	–	–	–	87 + 18	–
			–	–	–	–	–	703 + 18	–
	F(2,3)RP024N,H06(T)	61	53 + 4	59 + 4	–	–	–	–	–
			701 + 4	701 + 4	–	–	–	–	–
	F(2,3)RP030N06(T)	65	–	59 + 6	63 + 4	–	–	–	–
			–	701 + 6	701 + 4	–	–	–	–
	F(2,3)RP036N06(T)	75	–	–	63 + 4	73 + 8	–	–	–
			–	–	701 + 4	702 + 8	–	–	–
	F(2,3)RP042N06(T)	78	–	–	–	73 + 13	78 + 0	–	–
			–	–	–	702 + 13	702 + 0	–	–
	F(2,3)FP048N06(T)	84	–	–	–	73 + 16	78 + 10	87 + 11	–
			–	–	–	702 + 16	702 + 10	703 + 11	–
	F(2,3)FP060N06(T)	90	–	–	–	–	–	87 + 15	–
			–	–	–	–	–	703 + 15	7035 + 5
	F(2,3)FV060N06(T)	90	–	–	–	–	–	87 + 15	–
			–	–	–	–	–	703 + 15	703 + 5
	FOOTNOTES:

1.These orifices are factory mounted in the flow control device of each indoor coil and must be removed for TXV installation.

2.A TXV kit must be used with these coils to obtain system performance. (701,702,703 indicates 1TV07 ...series).

3.Systems matched with furnaces or air handlers not equipped with blower-off delays, may require blower Time Delay Kit #6918A5011.

4.These orifices are factory mounted in the flow control device of each indoor coil. A TXV is factory mounted if the model number has a (T) suffix.

5.This TXV is factory mounted in indoor coils, if the model number has a (T) suffix.

PROCEDURES:

1.Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaporator and for 15 feet of interconnecting line tubing.

2.Verify the orifice size and additional charge required for specific evaporator coil in the system using the above table.

3.Additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in the table above.

4.Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for evaporator + adder for line set.

5.If the orifice in the evaporator was changed, verify the evaporator nameplate has been marked with the correct orifice size.

4	Unitary Products Group

							036-21137-004 Rev. C (0505)
Additional R-22 Charge / Orifice Size for Various Matched Systems - 3 Phase
Outdoor Unit				H1RC036S	H1RC048S		H1RC060S
Unit Orifice (s) 1				–	–		–
Factory R-22 Charge, lbs-oz				6 - 2	7 - 10		9 - 3
Indoor Coil	Coil Orifice			TVX Kit2 = Additional Charge, Oz3
G2FD035(S,H)14	65			702 + 0	–		–
G2FD036(S,H)17,21	75			702 + 3	–		–
G2FD042(S,H)21	78			702 + 0	–		–
G2FD046(S,H)17	78			702 + 9	703 + 0		–
G2FD048(S,H)21,24	84			702 + 17	703 + 9		–
G2FD060(S,H)24	90			–	703 + 0		703 + 20
G2FD061H24	90			–	703 + 6		703 + 25
G1FA/G1UA036S14	73			702 + 1	–		–
G1FA/G1UA036S17,21	73			702 + 0	–		–
G1FA/G1UA048S17	84			–	703 + 2		–
G1FA/G1UA048S21	84			702 + 9	703 + 7		–
G1FA/G1UA060S21,24	90			–	703 + 14		703 + 20
G1NA036S17L	71			702 + 0	–		–
G1NA048S21D	78			702 + 0	703 + 0		–
G1NA048S24P	78			702 + 0	703 + 0		–
G1NA060S24T	87			–	–		703 + 0
G1NF036SOF	67			702 + 0	–		–
G1NF048SOF	78			–	702 + 0		–
G1NF060SOF	87			–	–		703 + 0
G1HD036	69			702 + 5	–		–
G1HD048	81			702 + 11	703 + 0		–
G1HD060	93			–	703 + 0		703 + 20
FOOTNOTES:

1.These orifices are factory mounted in the flow control device of each indoor coil and must be removed for TXV installation.

2.A TXV kit must be used with these coils to obtain system performance. (701,702,703 indicates 1TV07 ...series).

3.Systems matched with furnaces or air handlers not equipped with blower-off delays, may require blower Time Delay Kit #6918A5011.

PROCEDURES:

1.Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaporator and for 15 feet of interconnecting line tubing.

2.Verify the orifice size and additional charge required for specific evaporator coil in the system using the above table.

3.Additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in the table above.

4.Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for evaporator + adder

for line set.

5. If the orifice in the evaporator was changed, verify the evaporator nameplate has been marked with the correct orifice size.

Unitary Products Group

5

036-21137-004 Rev. C (0505)

COOLING CAPACITY - With Air Handler Coils

UNIT MODEL	AIR HANDLER				COIL1					COOLING
	MODEL	ELECTRIC2		W		RATED		NET MBH			SEER	SEER	EER
		HEAT KW			MODEL	CFM					W/O TXV	WITH TXV3
								TOTAL		SENS.
			1	PH 12	SEER AC WITH N1AH / G2FD
H2RC018S06	N1AHB0806	2,5,8,10		17	G2FD024(S,H)17	600		19.6		13.2	12.50	12.50	11.60
H2RC024S06	N1AHB0806	2,5,8,10		17	G2FD024(S,H)17	750		23.6		16.9	12.00	12.00	11.00
	N1AHB0806	2,5,8,10		17	G2FD030(S,H)17	750		24.0		17.3	12.00	12.00	11.10
H2RC030S06	N1AHB1206	2,5,8,10		17	G2FD030(S,H)17	1000		30.0		21.3	12.00	12.00	11.00
	N1AHB1206	2,5,8,10		17	G2FD036(S,H)17	1000		30.6		21.8	12.25	12.25	11.20
H2RC036S06	N1AHB1206	5,8,10,15,19		17	G2FD036(S,H)17	1200		33.8		23.6	11.50	11.50	10.70
	N1AHB1206	5,8,10,15,19		17	G2FD046(S,H)17	1200		35.0		24.4	12.00	12.00	10.90
H2RC042S06	N1AHC1606	5,8,10,15,20		21	G2FD042(S,H)21	1400		41.0		29.3	12.00	–	10.50
	N1AHC1606	5,8,10,15,20		21	G2FD048(S,H)21	1400		42.5		30.6	12.00	–	10.75
H2RC048S06	N1AHC1606	5,8,10,15,20		21	G2FD048(S,H)21	1575		46.5		36.0	12.20	12.20	10.90
	N1AHD2006	8,10,15,20,25,30		24	G2FD060(S,H)24	1575		48.0		36.4	12.50	12.50	11.10
	N1AHD2006	8,10,15,20,25,30		24	G2FD061H24	1575		48.5		34.5	12.50	12.50	11.20
H3RC060S06	N1AHD2006	8,10,15,20,25,30		24	G2FD060(S,H)24	1800		57.5		42.6	–	12.00	10.40
	N1AHD2006	8,10,15,20,25,30		24	G2FD061H24	1850		58.0		43.2	–	12.00	10.45
			3	PH 12	SEER AC WITH N1AH / G2FD
H1RC036S(25,46)	N1AHB1246	5,8,10,15,18		17	G2FD036(S,H)17	1255		33.6		24.9	–	12.00	10.65
	N1AHB1246	5,8,10,15,18		17	G2FD046(S,H)17	1250		34.8		25.8	–	12.00	10.95
	N1AHC1646	5,8,10,15,18		21	G2FD048(S,H)21	1600		45.5		33.7	–	12.20	11.20
H1RC048S(25,46)	N1AHD2046	8,10,15,20,25,30		24	G2FD060(S,H)24	1620		47.0		34.8	–	12.50	11.45
	N1AHD2046	8,10,15,20,25,30		24	G2FD061H24	1600		47.5		35.2	–	12.50	11.50
H1RC060S(25,46)	N1AHD2046	8,10,15,20,25,30		24	G2FD060(S,H)24(T)	1800		56.5		43.4	–	12.00	10.10
	N1AHD2046	8,10,15,20,25,30		24	G2FD061H24	1800		56.5		43.8	–	12.00	10.15
		1 PH 12 SEER / N1VS - VARIABLE SPEED
H2RC018S06	N1VSB12	10,15,18		17	G2FD024(S,H)17	650		20.2		13.2	13.75	13.75	12.80
H2RC024S06	N1VSB12	10,15,18		17	G2FD024(S,H)17	725		24.2		16.9	13.35	13.35	12.15
	N1VSB12	10,15,18		17	G2FD036(S,H)17	775		25.2		17.8	13.50	13.50	12.50
H2RC030S06	N1VSB12	10,15,18		17	G2FD036(S,H)17	1000		31.0		21.9	13.25	13.25	12.15
	N1VSB12	10,15,18		17	G2FD046(S,H)17	1000		32.0		22.3	13.75	13.75	12.55
	N1VSB12	10,15,18		17	G2FD046(S,H)17	1000		32.0		22.3	13.75	13.75	12.55
H2RC036S06	N1VSB12	10,15,18		17	G2FD036(S,H)17	1200		34.8		23.6	12.40	12.40	11.35
	N1VSB12	10,15,18		17	G2FD046(S,H)17	1210		35.8		24.4	13.00	13.00	11.65
	N1VSC16	10,15,18		21	G2FD048(S,H)21	1155		36.8		25.1	13.40	13.40	12.20
H2RC042S06	N1VSC16	10,15,18		21	G2FD048(S,H)21	1400		43.0		30.6	13.00	–	11.55
	N1VSC16	10,15,18		21	G2FD048(S,H)21	1590		47.0		30.6	12.80	–	11.40
H2RC048S06	N1VSC16	10,15,18		21	G2FD048(S,H)21	1590		47.0		34.9	12.80	12.80	11.40
	N1VSD20	10,15,18,30		24	G2FD060(S,H)24	1560		48.5		36.0	13.25	13.25	11.75
	N1VSD20	10,15,18,30		24	G2FD061H24	1560		49.0		36.4	13.30	13.30	11.90
H3RC060S06	N1VSD20	10,15,18,30		24	G2FD060(S,H)24	1780		56.0		42.3	–	12.10	10.25
	N1VSD20	10,15,18,30		24	G2FD061H24	1780		56.5		42.7	–	12.25	10.40
			1	PH 12 SEER AC / F2RP / RC / FC4,5
H2RC018S06	F2RC/F2FC024	5,8,10		18	–	600		20.0		13.2	12.50	12.50	11.70
	F2RP/F2FP024	5,8,10		18	–	600		20.0		13.2	12.50	12.50	11.70
	F2RC/F2FC024	5,8,10		18	–	750		23.4		17.5	11.50	11.50	10.85
H2RC024S06	F2RC/F2FC030	5,8,10,15		18	–	750		23.4		17.5	11.50	11.50	10.85
	F2RP/F2FP024	5,8,10		18	–	750		23.6		17.5	12.00	12.00	10.90
	F2RP/F2FP030	5,8,10,15		18	–	750		24.0		17.9	12.00	12.00	11.10
	F2RC/F2FC030	5,8,10,15		18	–	1000		29.8		21.5	12.00	12.00	11.00
H2RC030S06	F2RC/F2FC036	5,8,10,15		21	–	1000		31.0		22.4	12.25	12.25	11.30
	F2RP/F2FP030	5,8,10,15		18	–	1000		30.2		22.9	12.00	12.00	11.15
	F2RP/F2FP036	5,8,10,15,19		21	–	1000		30.2		23.5	12.00	12.00	11.15
	F2RC/F2FC036	5,8,10,15		21	–	1200		34.6		26.2	12.00	12.00	10.85
H2RC036S06	F2RP/F2FP036	5,8,10,15,19		21	–	1200		34.6		26.2	12.00	12.00	10.85
	F2RP/F2FP042	5,8,10,15		21	–	1200		34.8		26.3	11.60	11.60	10.70
	F2FP048	5,8,10,15,20,25		24	–	1200		35.4		26.7	12.00	12.00	10.90
H2RC042S06	F2RP/F2FP042	5,8,10,15		21	–	1400		40.5		28.9	11.80	–	10.35
	F2FP048	5,8,10,15,20,25		24	–	1400		42.5		30.5	12.00	–	10.55
H2RC048S06	F2FP048	5,8,10,15,20,25		24	–	1565		46.5		34.9	11.40	11.40	10.75
	F2FP060	5,8,10,15,20,25		24	–	1575		48.0		35.9	11.50	11.50	10.70
	F2FV060	8,10,15,20,25		24	–	1560		48.5		35.9	13.20	13.20	11.70
H3RC060S06	F2FP060	5,8,10,15,20,25		24	–	1800		56.0		42.0	–	12.00	10.00
	F2FV060	8,10,15,20,25		24	–	1780		56.0		42.3	–	12.10	10.30
Rated in accordance	with DOE test	procedures (Federal Register 12-27-79 and 3-18-88) and ARI Standards 210.

Cooling MBH based on 80°F entering air temperature, 50% RH, and rated air flow.

EER (Energy Efficiency Ratio) is the total cooling output in BTU’s at a 95°F outdoor ambient divided by the total electric power in watt-hours at those conditions. SEER (Seasonal Energy Efficiency Ratio) is the total cooling output in BTU’s during a normal annual usage period for cooling divided by the total electric power input in watt-hours during the same period.

1.G2FD coils available with a factory installed horizontal drain pan. See price pages for specific model number.

2.Single phase units require single phase 2HK heaters. Three phase units require three phase 2HK heaters.

3.TXV = Thermal Expansion Valve kit required. Use 1TV700 series kit.

4.To meet R=4.2 insulation requirements, substitute F2FP for F2RP, and F2FC for F2RC. models. All ratings remain the same.

5.FG8, FG9, and FL8 furnaces and F2RP / F2RC air handlers have B.O.D (Blower on Delay) standard.

- = Not applicable.

6	Unitary Products Group

036-21137-004 Rev. C (0505)

COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils

		FURNACE**		COIL			COOLING
	UNIT MODEL	CFM RANGE	W	MODEL	RATED CFM	NET MBH		SEER	SEER + TXV1	EER
		(Min.-max.)				TOTAL	SENS.	W/O TXV
			14,17	G1FA024S14,17	600	19.2	13.0	12.00*	12.00	11.35
			14	G1HA024H14	600	19.2	13.6	12.00*	–	11.50
			14	G1HA024H14T	600	19.2	13.6	–	12.00*	11.60
			-	G1HD024	600	20.0	13.5	12.50*	12.50	11.70
	H2RC018S06	525	17	G1NA030S17K	600	20.0	13.5	12.75*	12.75	11.75
			21	G1NA030S21M	600	20.0	13.5	12.50*	12.50	11.75
		675
			14,17	G1UA024S14,17	600	19.2	13.0	12.00*	12.00	11.35
			14,17	G2FD024(S,H)14,17	600	19.6	13.2	12.50*	12.50	11.60
			17	G2FD030(S,H)17	600	20.0	13.5	12.60*	12.60	11.75
			14	G2FD035(S,H)14	600	20.0	13.5	12.60*	12.60	11.75
			14,17	G1FA024S14,17	750	23.0	16.4	11.80*	11.80	10.70
			14	G1FA030S14	750	23.6	16.9	12.00*	12.00	11.00
			14	G1FA036S14	750	24.2	17.6	12.00*	12.00	11.25
			17,21	G1FA036S17,21	750	24.0	17.3	12.00*	12.00	11.10
			14	G1HA024H14	750	19.2	13.6	12.00*	–	10.90
			14	G1HA024H14T	800	23.5	16.7	–	12.00*	10.90
			14	G1HA036H14	800	24.6	17.5	12.00	–	11.35
			-	G1HD024	750	24.0	17.2	12.00*	12.00	11.05
			-	G1HD036	750	24.6	17.6	12.10*	12.10	11.35
	H2RC024S06	650	17	G1NA030S17K	750	24.0	17.2	12.00*	12.00	11.15
		850
			21	G1NA030S21M	750	24.0	17.2	12.00*	12.00	11.15
			14,17	G1UA024S14,17	750	23.0	16.4	11.80*	11.80	10.70
			14	G1UA030S14	750	23.6	16.9	12.00*	12.00	11.00
			14	G1UA036S14	750	24.2	17.6	12.00*	12.00	11.25
			17,21	G1UA036S17,21	750	24.0	17.3	12.00*	12.00	11.10
			14,17	G2FD024(S,H)14,17	750	23.6	16.9	12.00*	12.00	11.00
			17	G2FD030(S,H)17	750	24.0	17.3	12.00*	12.00	11.10
			14	G2FD035(S,H)14	750	24.0	17.3	12.10*	12.10	11.10
			17	G2FD036(S,H)17	750	24.6	17.8	12.15*	12.15	11.35
			14	G1FA030S14	1000	29.2	20.7	11.85*	11.85	10.80
			14	G1FA036S14	1000	30.4	21.6	12.00*	12.00	11.10
			17,21	G1FA036S17,21	1000	30.0	21.3	12.00*	12.00	11.00
			17	G1FA048S17	1000	31.2	22.3	12.50*	12.50	11.45
			21	G1FA048S21	1000	31.2	22.3	12.50*	12.50	11.35
			14	G1HA036H14	1000	30.3	21.5	12.00*	–	11.25
			14	G1HA036H14	1000	30.2	21.4	–	12.00*	11.25
			17	G1HA036H17	1000	30.4	21.9	12.00*	–	11.35
			17	G1HA036H17T	1000	30.5	22.0	–	12.00*	11.35
			-	G1HD036	1000	30.8	21.9	12.75*	12.75	11.25
			17	G1NA030S17K	1000	30.2	21.4	12.00*	12.00	11.05
	H2RC030S06	875	21	G1NA030S21M	1000	30.2	21.4	12.00*	12.00	11.05
		1125
			17	G1NA036S17L	1000	31.4	22.3	12.50*	12.50	11.45
			14	G1UA030S14	1000	29.2	20.7	11.85*	11.85	10.80
			14	G1UA036S14	1000	30.4	21.6	12.00*	12.00	11.10
			17,21	G1UA036S17,21	1000	30.0	21.3	12.00*	12.00	11.00
			17	G1UA048S17	1000	31.2	22.3	12.50*	12.50	11.45
			21	G1UA048S21	1000	31.2	22.3	12.50*	12.50	11.35
			17	G2FD030(S,H)17	1000	30.0	21.3	12.00*	12.00	11.00
			14	G2FD035(S,H)14	1000	30.0	21.3	12.00*	12.00	11.00
			17	G2FD036(S,H)17	1000	30.6	21.8	12.25*	12.25	11.20
			21	G2FD036(S,H)21	1000	30.8	21.9	12.25*	12.25	11.25
			21	G2FD042(S,H)21	1000	31.0	22.1	12.50*	12.50	11.35
			17	G2FD046(S,H)17	1000	31.4	22.3	12.50*	12.50	11.45

For Notes See Page 9.

Unitary Products Group

7

036-21137-004 Rev. C (0505)

COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils (Continued)

		FURNACE**		COIL			COOLING
	UNIT MODEL	CFM RANGE	W	MODEL	RATED CFM	NET MBH		SEER	SEER + TXV1	EER
		(Min.-max.)				TOTAL	SENS.	W/O TXV
			14	G1FA036S14	1200	33.6	23.4	11.50*	11.50	10.60
			17,21	G1FA036S17,21	1200	33.0	23.0	11.25*	11.25	10.45
			17	G1FA048S17	1200	35.0	24.4	12.00*	12.00	10.90
			21	G1FA048S21	1200	34.0	25.2	12.00*	12.00	10.70
			14	G1HA036H14	1150	33.5	23.8	12.00*	–	10.75
			14	G1HA036H14	1150	33.4	23.7	–	12.00*	10.75
			17	G1HA036H17	1200	34.0	24.5	12.00*	–	10.80
			17	G1HA036H17T	1200	34.0	24.5	–	12.00*	10.80
			21	G1HA048H21	1200	34.0	24.8	12.00*	–	10.70
			21	G1HA048H21T	1200	33.3	24.3	–	12.00	10.70
			-	G1HD036	1200	34.0	23.7	11.80*	11.80	10.70
			-	G1HD048	1200	35.4	24.7	12.00*	12.00	11.00
	H2RC036S06	1050	17	G1NA036S17L	1200	35.0	24.8	12.00*	12.00	10.90
		1350
			21	G1NA048S21D	1200	35.0	24.8	12.00*	12.00	10.90
			14	G1UA036S14	1200	33.6	23.4	11.50*	11.50	10.60
			17,21	G1UA036S17,21	1200	33.0	23.0	11.25*	11.25	10.45
			17	G1UA048S17	1200	35.0	24.4	12.00*	12.00	10.90
			21	G1UA048S21	1200	34.0	25.2	12.00*	12.00	10.70
			21	G1NA048S21D	1200	35.0	25.2	12.00*	12.00	10.40
			14	G2FD035(S,H)14	1200	33.0	23.0	11.25*	11.25	10.45
			17	G2FD036(S,H)17	1200	33.8	23.6	11.50*	11.50	10.70
			21	G2FD036(S,H)21	1200	34.2	23.8	12.50*	12.50	10.75
			21	G2FD042(S,H)21	1200	34.6	24.1	12.00*	12.00	10.80
			17	G2FD046(S,H)17	1200	35.0	24.4	12.00*	12.00	10.90
			21,24	G2FD048(S,H)21,24	1200	36.0	25.1	12.10*	12.10	11.10
			14	G1FA036S14	1235	33.4	25.0	–	11.50	10.65
			17,21	G1FA036S17,21	1235	33.0	24.4	–	11.50	10.55
			21	G1FA048S21	1235	35.0	25.9	–	12.00	10.70
			-	G1HD036	1235	33.4	24.7	–	11.80	10.70
			-	G1HD048	1235	35.0	25.8	–	12.00	11.05
			17	G1NA036S17L	1200	35.0	24.4	–	12.00	10.90
			21	G1NA048S21D	1200	35.0	24.4	–	12.00	10.90
	H1RC036S(25,46)	1050	14	G1UA036S14	1200	33.4	25.0	–	11.50	10.65
		1350	17,21	G1UA036S17,21	1235	33.0	24.4	–	11.50	10.55
			21	G1UA048S21	1235	35.0	25.9	–	12.00	10.70
			14	G2FD035(S,H)14	1200	32.8	24.3	–	11.55	10.55
			17	G2FD036(S,H)17	1250	33.6	24.9	–	12.00	10.65
			21	G2FD036(S,H)21	1200	34.2	25.3	–	12.00	10.90
			21	G2FD042(S,H)21	1235	34.4	25.5	–	12.00	10.90
			17	G2FD046(S,H)17	1250	34.8	25.8	–	12.00	10.95
			21,24	G2FD048(S,H)21,24	1250	35.4	26.2	–	12.10	11.15
			17	G1FA048S17	1400	42.0	30.2	12.00*	–	10.60
			21	G1FA048S21	1400	41.5	29.7	12.00	–	10.65
			21,24	G1FA060S21,24	1400	43.0	30.7	12.50	–	10.95
			21	G1HA048H21	1400	41.5	30.3	12.00*	–	10.65
			21	G1HA048H21T	1400	40.7	29.7	–	12.00	10.65
			-	G1HD048	1400	41.5	29.7	12.00	–	10.60
	H2RC042S06	1225	21	G1NA048S21D	1400	41.0	28.6	12.00*	–	10.40
		1575
			17	G1UA048S17	1400	42.0	30.2	12.00*	–	10.60
			21	G1UA048S21	1400	41.5	29.7	12.00	–	10.65
			21,24	G1UA060S21,24	1400	43.0	30.7	12.50*	–	10.95
			21	G2FD042(S,H)21	1400	41.0	29.3	12.00*	–	10.50
			17	G2FD046(S,H)17	1400	42.0	30.2	12.00*	–	10.60
			21,24	G2FD048(S,H)21,24	1400	42.5	30.6	12.00	–	10.75

For Notes See Page 9.

8	Unitary Products Group