Yetter 2967-035 TITAN Universal Face Plate Mounted Floating Residue Manager User Manual

Loading...

2967-035 “TITAN”

UNIVERSAL

FACE PLATE MOUNTED FLOATING RESIDUE MANAGER

2565-487_REV_B 12/11

YETTER MANUFACTURING CO.

FOUNDED 1930

Colchester, IL 62326-0358 Toll free: 800/447-5777

309/776-3222 (Fax) Website: www.yetterco.com E-mail: info@yetterco.com

FOREWORD

You’ve just joined an exclusive but rapidly growing club.

For our part, we want to welcome you to the group and thank you for buying a Yetter Product.

We hope your new Yetter implement will help you achieve both increased productivity and increased efficiency so that you may generate more profit. This operator’s manual has been designed into six major sections.

Foreword, Safety Precautions, assembly instructions, Operation, parts identification and troubleshooting.

It is important the owner/operator knows the implement model number. Write the model number in the space provided and use it in all correspondence when referring to the implement.

Throughout the manual references may be made to left side and right side. These terms are used as viewed from the operator’s seat facing the front of the tractor.

This SAFETY ALERT SYMBOL indicates important safety messages in the manual. When you see this symbol, be alert

to the possibility of PERSONAL INJURY and carefully read the message that follows.

The word NOTE is used to convey information that is out of context with the manual text. It contains special information such as specifications, techniques, reference information

and other information of a supplementary nature. The word IMPORTANT is used in the text when immediate damage will occur to the machine due to improper technique or operation. Important will apply to the same information as specified by note only of an immediate and urgent nature.

It is the responsibility of the user to read the operator’s manual and comply with the safe and correct operating procedure and to lubricate and maintain the product according to the maintenance schedule in the operator’s manual.

The user is responsible for inspecting his machine and for having parts repaired or replaced when continued use of the product would cause damage or excessive wear to the other parts.

It is the user’s responsibility to deliver his machine to the Yetter dealer who sold him the product for service or replacement of defective parts that are covered by the warranty policy.

If you are unable to understand or follow the instructions provided in the publication, consult you local Yetter dealer or

contact:

YETTER MANUFACTURING CO.

309/776-4111 800/447-5777 309/776-3222 (FAX) Website: www.yetterco.com E-mail: info@yetterco.com

WARRANTY POLICY

Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being expressly limited to replacement at the factory of such parts or products as will appear to be defective after inspection. This warranty does not obligate the Company to bear cost of labor in replacement of parts. It is the policy of the company to make improvements without incurring obligations to add them to any unit already sold. No warranty is made or authorized to be made, other than herein set forth. This warranty is in effect for one year after purchase.

Model Number:_________________________

Dealer :___________________

Yetter Manufacturing warrants its own products only and cannot be responsible for damage to equipment on which it is mounted.

2

SAFETY

A brief description of signal words that may be used in this manual:

CAUTION: Used as a general reminder of good safety practices or to direct attention to unsafe practices.

WARNING: Denotes a specific potential hazard.

DANGER: Denotes the most serious specific potential hazard.

SAFETY PRECAUTIONS

You can make your farm a safer place to live and work if you observe the safety precautions given. Study these precautions carefully and insist that those working with you and for you follow them.

Finally, remember this: an accident is usually caused by someone’s carelessness, neglect or oversight.

WARNING

Never clean, lubricate or adjust a machine that is in motion. Always lower or block the implement before performing service.

If the machine must be serviced in the raised position, jack or block it up to prevent it from accidentally falling and injuring someone.

Do not allow riders on the tractor or implement.

Use speeds and caution dictated by the terrain being traversed. Do not operate on any slope steep enough to cause tipping or loss of control.

Be sure all personnel are clear of the immediate area before operating.

Read and understand the operator’s manual and require all other persons who will operate the equipment to do the same.

Be familiar with all tractor and implement controls and be prepared to stop engine and implements quickly in an emergency.

CAUTION

Consult your implement and tractor operator’s manual for correct and safe operating practices.

Beware of towed implement width and allow safe clearance.

FAILURE TO HEED MAY RESULT IN PERSONAL INJURY OR DEATH.

3

TABLE OF CONTENTS

Introduction…………………………………………………………..pg. 2

Warranty……………………………….……………………………..pg. 2

Safety Information…………………………………………………...pg. 3

Table of Contents……………………………………………………pg. 4

Optional Equipment…………………………………………………pg. 4

Application/Use Guide………………………………………………pg. 5

Assembly Instruction…………………….………………………….pg.6-9

Operation……………………………...……………………………..pg. 10

Maintenance/ Lubrication…………………………………………..pg. 11-16

Parts Identification………………………………..………….……...pg.17

OPTIONAL EQUIPMENT

2967-186 FLOATER WHEEL L.H. ASSEMBLY SHOWN

(2) REQUIRED PER ROW

4

TITAN F.P.M. RESIDUE MANAGER

OPERATION / USE GUIDE

IMPORTANT: The 2967-035 Residue Manager Will Limit the full “up-travel” of the planter row unit. Please check the amount of travel that the planter row unit has before going to the field to plant.

NOTE: The recommended height of a level planter toolbar frame is 18”-22”. Always visually check seed spacing and depth-calibrate your equipment if necessary.

Solution to “UP” travel issue. Trim upper corners of face plate bracket.

If there is insufficient clearance between the residue manager wheels and the fertilizer coulter opener, then a fertilizer extension bar is required to move the fertilizer coulter forward to have sufficient clearance.

5

ASSEMBLY INSTRUCTIONS

2967-035 RESIDUE MANAGER ONLY

NOTE: Do not fully tighten the mounting hardware at this time. Alignment adjustments will be made once the R.M. wheels are attached.

When using the 2967-035 Residue Manager unit with out a coulter, attach the 2967-281 – Mount W.A. using 4) ½” x 1 ½” bolts, large flat washers and lock nuts.

JD MAX EMERGE II COULTER

Use 3) ½” x 2” carriage bolts when mounting a JD MEII coulter or a White single arm coulter (700728036).

Use 4) ½” x 2” carriage bolts when mounting a JD 7000 coulter, Kinze double arm, White double arm, or the Yetter 2960-130 Double Arm Coulter.

2960 SERIES II UNIT MOUNTED CONSERVATION COULTER

Use 2) ½” x 2” carriage bolts (upper holes), 1) ½” x 2” hex bolt and a large flat washer (lower left hole) are used when mounting the Yetter Series II coulter.

6

+ 14 hidden pages