Yamaha V STAR 1300 TOURER Manual

0 (0)

OWNER’S MANUAL

XVS13CTX(C)

LIT-11626-21-30

5S6-28199-11

EAU10041

INTRODUCTION

EAU10080

Congratulations on your purchase of the Yamaha XVS13CTX(C). This model is the result of Yamaha’s vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields.

This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle. If you have any questions concerning the operation or maintenance of your motorcycle, please consult a Yamaha dealer.

The design and manufacture of this Yamaha motorcycle fully comply with the emissions standards for clean air applicable at the date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of the motorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the recommended maintenance schedules and operating instructions contained within this manual.

IMPORTANT MANUAL INFORMATION

EAU10131

Particularly important information is distinguished in this manual by the following notations:

The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS

INVOLVED!

				Failure to follow WARNING instructions could result in severe injury or death to the
	WARNING			motorcycle operator, a bystander or a person inspecting or repairing the motor-
				cycle.


				A CAUTION indicates special precautions that must be taken to avoid damage to
	CAUTION:
	CAUTION:			the motorcycle.
				the motorcycle.


	NOTE:			A NOTE provides key information to make procedures easier or clearer.

NOTE:

●This manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle is subsequently sold.

●Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your motorcycle and this manual. If you have any questions concerning this manual, please consult your Yamaha dealer.

IMPORTANT MANUAL INFORMATION

EWA10010

WARNING

PLEASE READ THIS MANUAL AND THE “YOU AND YOUR MOTORCYCLE: RIDING TIPS” BOOKLET CAREFULLY AND COMPLETELY BEFORE OPERATING THIS MOTORCYCLE. DO NOT ATTEMPT TO OPERATE THIS MOTORCYCLE UNTIL YOU HAVE ATTAINED ADEQUATE KNOWLEDGE OF ITS CONTROLS AND OPERATING FEATURES AND UNTIL YOU HAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES. REGULAR INSPECTIONS AND CAREFUL MAINTENANCE, ALONG WITH GOOD RIDING SKILLS, WILL ENSURE THAT YOU SAFELY ENJOY THE CAPABILITIES AND THE RELIABILITY OF THIS MOTORCYCLE.

*Product and specifications are subject to change without notice.

IMPORTANT MANUAL INFORMATION

EAU10192

AFFIX DEALER

LABEL HERE

XVS13CTX(C)

OWNER’S MANUAL

Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A. is expressly prohibited.

Printed in Japan.

P/N LIT-11626-21-30

SAFETY INFORMATION ..................	1-1
Location of important labels ...........	1-5
DESCRIPTION ..................................	2-1
Left view ..........................................	2-1
Right view ........................................	2-2
Controls and instruments ................	2-3
INSTRUMENT AND CONTROL
FUNCTIONS .......................................	3-1
Main switch/steering lock ................	3-1
Indicator and warning lights ............	3-2
Multi-function meter unit .................	3-3
Handlebar switches ........................	3-6
Clutch lever ....................................	3-8
Shift pedal ......................................	3-8
Brake lever .....................................	3-8
Brake pedal ....................................	3-9
Fuel tank cap ..................................	3-9
Fuel ..............................................	3-10
Catalytic converter ........................	3-11
Rider seat .....................................	3-11
Helmet holder ...............................	3-12
Sidebags ......................................	3-12
Adjusting the shock absorber
assembly ...................................	3-13
Sidestand .....................................	3-14
Ignition circuit cut-off system ........	3-15
PRE-OPERATION CHECKS..............	4-1
Pre-operation check list ..................	4-2

OPERATION AND IMPORTANT
RIDING POINTS ................................	5-1
Starting the engine .........................	5-1
Shifting ...........................................	5-2
Engine break-in ..............................	5-3
Parking ...........................................	5-4
PERIODIC MAINTENANCE AND
MINOR REPAIR.................................	6-1
PERIODIC MAINTENANCE ..........	6-1
Owner’s tool kit ..............................	6-1
Periodic maintenance chart for the
emission control system .............	6-3
General maintenance and
lubrication chart ..........................	6-4
Removing and installing the
panel ...........................................	6-9
Checking the spark plugs ..............	6-9
Canister (for California only) ........	6-11
Engine oil and oil filter cartridge ...	6-11
Coolant ........................................	6-14
Replacing the air filter element ....	6-15
Checking the throttle cable free
play ...........................................	6-16
Valve clearance ...........................	6-16
Tires .............................................	6-17
Cast wheels .................................	6-19
Accessories and replacement
parts .........................................	6-19
Adjusting the clutch lever free
play ...........................................	6-20

Adjusting the brake lever free
play ...........................................	6-20
Adjusting the rear brake light
switch ........................................	6-21
Checking the front and rear
brake pads ................................	6-21
Checking the brake fluid level ......	6-22
Changing the brake fluid ..............	6-23
Drive belt slack .............................	6-23
Checking and lubricating the
cables .......................................	6-24
Checking and lubricating the
throttle grip and cable ...............	6-24
Checking and lubricating the
brake and shift pedals ...............	6-25
Checking and lubricating the
brake and clutch levers .............	6-25
Checking and lubricating the
sidestand ..................................	6-26
Lubricating the swingarm pivots ...	6-26
Lubricating the rear suspension ...	6-27
Checking the front fork .................	6-27
Checking the steering ..................	6-28
Checking the wheel bearings .......	6-28
Battery ..........................................	6-29
Replacing the fuses ......................	6-30
Replacing the headlight bulb ........	6-32
Replacing the tail/brake light
bulb ...........................................	6-33
Replacing a front turn signal light
bulb ...........................................	6-34

TABLE OF CONTENTS

Replacing a rear turn signal light
bulb ...........................................	6-34
Replacing the license plate light
bulb ...........................................	6-35
Supporting the motorcycle ............	6-36
Troubleshooting ............................	6-36
Troubleshooting charts .................	6-37
MOTORCYCLE CARE AND
STORAGE ..........................................	7-1
Matte color caution .........................	7-1
Care ................................................	7-1
Storage ...........................................	7-4
SPECIFICATIONS .............................	8-1
CONSUMER INFORMATION.............	9-1
Identification numbers ....................	9-1
Reporting safety defects .................	9-3
Motorcycle noise regulation ............	9-4
Maintenance record ........................	9-5
YAMAHA MOTOR CORPORATION,
U.S.A. STREET AND ENDURO
MOTORCYCLE LIMITED
WARRANTY ................................	9-7
YAMAHA EXTENDED SERVICE
(Y.E.S.) ........................................	9-9

SAFETY INFORMATION

EAU10281

MOTORCYCLES ARE SINGLE TRACK VEHICLES. THEIR SAFE USE AND OPERATION ARE DEPENDENT UPON THE USE OF PROPER RIDING TECHNIQUES AS WELL AS THE EXPERTISE OF THE OPERATOR. EVERY OPERATOR SHOULD KNOW THE FOLLOWING REQUIREMENTS BEFORE RIDING THIS MOTORCYCLE.

HE OR SHE SHOULD:

●OBTAIN THOROUGH INSTRUCTIONS FROM A COMPETENT SOURCE ON ALL ASPECTS OF MOTORCYCLE OPERATION.

●OBSERVE THE WARNINGS AND MAINTENANCE REQUIREMENTS IN THE OWNER’S MANUAL.

●OBTAIN QUALIFIED TRAINING IN SAFE AND PROPER RIDING TECHNIQUES.

●OBTAIN PROFESSIONAL TECHNICAL SERVICE AS INDICATED BY THE OWNER’S MANUAL

AND/OR WHEN MADE NECESSARY BY MECHANICAL CONDITIONS.

Safe riding

●Always make pre-operation checks. Careful checks may help prevent an accident.

●This motorcycle is designed to carry the operator and a passenger.

●The failure of motorists to detect and recognize motorcycles in traffic is the predominating cause of automobile/motorcycle accidents. Many accidents have been caused by an automobile driver who did not see the motorcycle. Making yourself conspicuous appears to be very effective in reducing the chance of this type of accident.

Therefore:

•Wear a brightly colored jacket.

•Use extra caution when you are approaching and passing through intersections, since intersections are the most likely places for motorcycle accidents to occur.

•Ride where other motorists can see you. Avoid riding in another motorist’s blind spot.

● Many accidents involve inexperi- 1 enced operators. In fact, many operators who have been involved in accidents do not even have a current motorcycle license.

•Make sure that you are qualified and that you only lend your motorcycle to other qualified operators.

•Know your skills and limits. Staying within your limits may help you to avoid an accident.

•We recommend that you practice riding your motorcycle where there is no traffic until you have become thoroughly familiar with the motorcycle and all of its controls.

●Many accidents have been caused by error of the motorcycle operator. A typical error made by the operator is veering wide on a turn

1-1

SAFETY INFORMATION

due to EXCESSIVE SPEED or undercornering (insufficient lean angle for the speed).

1• Always obey the speed limit and never travel faster than warranted by road and traffic conditions.

•Always signal before turning or changing lanes. Make sure that other motorists can see you.

●The posture of the operator and passenger is important for proper control.

•The operator should keep both hands on the handlebar and both feet on the operator footrests during operation to maintain control of the motorcycle.

•The passenger should always hold onto the operator, the seat strap or grab bar, if equipped, with both hands and keep both feet on the passenger footrests.

•Never carry a passenger unless he or she can firmly place both feet on the passenger footrests.

●Never ride under the influence of alcohol or other drugs.

●This motorcycle is designed for onroad use only. It is not suitable for off-road use.

Protective apparel

The majority of fatalities from motorcycle accidents are the result of head injuries. The use of a safety helmet is the single most critical factor in the prevention or reduction of head injuries.

●Always wear an approved helmet.

●Wear a face shield or goggles. Wind in your unprotected eyes could contribute to an impairment of vision that could delay seeing a hazard.

●The use of a jacket, heavy boots, trousers, gloves, etc., is effective in preventing or reducing abrasions or lacerations.

●Never wear loose-fitting clothes, otherwise they could catch on the control levers, footrests, or wheels and cause injury or an accident.

●Never touch the engine or exhaust system during or after operation. They become very hot and can

cause burns. Always wear protective clothing that covers your legs, ankles, and feet.

●A passenger should also observe the above precautions.

Modifications

Modifications made to this motorcycle not approved by Yamaha, or the removal of original equipment, may render the motorcycle unsafe for use and may cause severe personal injury. Modifications may also make your motorcycle illegal to use.

Loading and accessories

Adding accessories or cargo to your motorcycle can adversely affect stability and handling if the weight distribution of the motorcycle is changed. To avoid the possibility of an accident, use extreme caution when adding cargo or accessories to your motorcycle. Use extra care when riding a motorcycle that has added cargo or accessories. Here are some general guidelines to follow if loading cargo or adding accessories to your motorcycle:

1-2

SAFETY INFORMATION

The total weight of the operator, passenger, accessories and cargo must not exceed the maximum load limit.

Maximum load:

190 kg (419 lb)

When loading within this weight limit, keep the following in mind:

●Cargo and accessory weight should be kept as low and close to the motorcycle as possible. Make sure to distribute the weight as evenly as possible on both sides of the motorcycle to minimize imbalance or instability.

●Shifting weights can create a sudden imbalance. Make sure that accessories and cargo are securely attached to the motorcycle before riding. Check accessory mounts and cargo restraints frequently.

●Never attach any large or heavy items to the handlebar, front fork, or front fender. These items, including such cargo as sleeping

bags, duffel bags, or tents, can create unstable handling or a slow steering response.

Accessories

Genuine Yamaha accessories have been specifically designed for use on this motorcycle. Since Yamaha cannot test all other accessories that may be available, you must personally be responsible for the proper selection, installation and use of non-Yamaha accessories. Use extreme caution when selecting and installing any accessories.

Keep the following guidelines in mind, as well as those provided under “Loading” when mounting accessories.

●Never install accessories or carry cargo that would impair the performance of your motorcycle. Carefully inspect the accessory before using it to make sure that it does not in any way reduce ground clearance or cornering clearance,

limit suspension travel, steering travel or control operation, or obscure lights or reflectors.

• Accessories fitted to the handle- 1 bar or the front fork area can create instability due to improper weight distribution or aerodynamic changes. If accessories

are added to the handlebar or front fork area, they must be as lightweight as possible and should be kept to a minimum.

•Bulky or large accessories may seriously affect the stability of the motorcycle due to aerodynamic effects. Wind may attempt to lift the motorcycle, or the motorcycle may become unstable in cross winds. These accessories may also cause instability when passing or being passed by large vehicles.

•Certain accessories can displace the operator from his or her normal riding position. This improper position limits the freedom of movement of the opera-

1-3

SAFETY INFORMATION

tor and may limit control ability, therefore, such accessories are not recommended.

1 ● Use caution when adding electrical accessories. If electrical accessories exceed the capacity of the motorcycle’s electrical system, an electric failure could result, which could cause a dangerous loss of lights or engine power.

Gasoline and exhaust gas

●GASOLINE IS HIGHLY FLAMMABLE:

•Always turn the engine off when refueling.

•Take care not to spill any gasoline on the engine or exhaust system when refueling.

•Never refuel while smoking or in the vicinity of an open flame.

●Never start the engine or let it run for any length of time in a closed area. The exhaust fumes are poisonous and may cause loss of consciousness and death within a short time. Always operate your motorcycle in an area that has adequate ventilation.

●Always turn the engine off before leaving the motorcycle unattended and remove the key from the main switch. When parking the motorcycle, note the following:

•The engine and exhaust system may be hot, therefore, park the motorcycle in a place where pedestrians or children are not likely to touch these hot areas.

•Do not park the motorcycle on a slope or soft ground, otherwise it may fall over.

•Do not park the motorcycle near a flammable source, (e.g., a kerosene heater, or near an open flame), otherwise it could catch fire.

●When transporting the motorcycle in another vehicle, make sure that it is kept upright. If the motorcycle should lean over, gasoline may leak out of the fuel tank.

●If you should swallow any gasoline, inhale a lot of gasoline vapor, or allow gasoline to get into your eyes, see your doctor immediately. If any gasoline spills on your skin

or clothing, immediately wash the affected area with soap and water and change your clothes.

1-4

SAFETY INFORMATION

EAU10381

Location of important labels

Please read the following important labels carefully before operating this vehicle.

1-5

SAFETY INFORMATION

1-6

SAFETY INFORMATION

5	6	1
		1

1-7

DESCRIPTION

EAU10410

Left view

1.Front turn signal/position lights (page 6-34)

2.Headlight (page 6-32)

3.Seat lock (page 3-11)

4.Fuel injection system fuse (page 6-30)

5.Fuse box (page 6-30)

6.Main fuse (page 6-30)

7.Helmet holder (page 3-12)

8.License plate light (page 6-35)

9. Rear turn signal light (page 6-34) 10.Tail/brake light (page 6-33)

11.Engine oil level check window (page 6-11) 12.Shift pedal (page 3-8)

13.Engine oil filler cap (page 6-11)

2-1

DESCRIPTION

EAU10420

Right view

1.	Sidebag (page 3-12)	9. Rear brake light switch (page 6-21)
2.	Rear brake fluid reservoir (page 6-22)	10.Engine oil filter cartridge (page 6-11)
3.	Owner’s tool kit (page 6-1)	11.Engine oil drain bolt (page 6-11)
4.	Battery (page 6-29)	12.Coolant reservoir (page 6-14)
5.	Air filter element (page 6-15)	13.Shock absorber assembly spring preload adjusting ring (page 3-13)

6.Fuel tank cap (page 3-9)

7.Front brake fluid reservoir (page 6-22)

8.Brake pedal (page 3-9)

2-2

DESCRIPTION

EAU10430

Controls and instruments

1.Clutch lever (page 3-8)

2.Left handlebar switches (page 3-6)

3.Multi-function meter unit (page 3-3)

4.Main switch/steering lock (page 3-1)

5.Right handlebar switches (page 3-6)

6.Throttle grip (page 6-16)

7.Brake lever (page 3-8)

2-3

INSTRUMENT AND CONTROL FUNCTIONS

EAU10460	EAU10660
Main switch/steering lock	OFF
	All electrical systems are off. The key
	can be removed.
	EAU10680
	LOCK
	The steering is locked, and all electrical
	systems are off. The key can be re-
	moved.
	To lock the steering

The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below.

EAU10540

All electrical circuits are supplied with power, and the meter lighting, taillight, license plate light and position lights come on, and the engine can be started. The key cannot be removed.

NOTE:

The headlight comes on automatically when the engine is started and stays on until the key is turned to “OFF”, even if the engine stalls.

1.Push.

2.Turn.

1.Turn the handlebars all the way to the left.

2.Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it.

3.Remove the key.

To unlock the steering

1.Push.

2.Turn.

Push the key in, and then turn it to “OFF” while still pushing it.

EWA10060

WARNING

Never turn the key to “OFF” or “LOCK” while the vehicle is moving, otherwise the electrical systems will be switched off, which may result in loss of control or an accident. Make sure that the vehicle is stopped before turning the key to “OFF” or “LOCK”.

3-1

INSTRUMENT AND CONTROL FUNCTIONS

EAU11003

Indicator and warning lights

1.Neutral indicator light “ ”

2.Coolant temperature warning light “ ”

3.Engine trouble warning light “ ”

4.High beam indicator light “ ”

5.Turn signal indicator light “”

6.Oil level warning light “ ”

7.Fuel level warning light “”

EAU11020

Turn signal indicator light “”

This indicator light flashes when the turn signal switch is pushed to the left or right.

EAU11060

Neutral indicator light “ ”

This indicator light comes on when the transmission is in the neutral position.

EAU11080

High beam indicator light “”

This indicator light comes on when the high beam of the headlight is switched on.

EAU11250

Oil level warning light “”

This warning light comes on when the engine oil level is low.

The electrical circuit of the warning light can be checked by turning the key to “ON”.

If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit.

NOTE:

●Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction.

●This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The

oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle.

EAU42740

Fuel level warning light “”

This warning light comes on when the fuel level drops below approximately 3.7 L (0.98 US gal) (0.81 Imp.gal). When this occurs, refuel as soon as possible.

The electrical circuit of the warning light can be checked by turning the key to “ON”.

If the warning light does not come on for a few seconds, and then go off, have a Yamaha dealer check the electrical circuit.

NOTE:

●The vehicle must be on a level surface and positioned upright, otherwise the fuel level warning light may not come on and go off at the appropriate times.

●This model is also equipped with a self-diagnosis device for the fuel level detection circuit. If the fuel

3-2

INSTRUMENT AND CONTROL FUNCTIONS

level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The fuel level warning light will flash eight times, and then go off for 3.0 seconds. If this occurs, have a Yamaha dealer check the vehicle.

EAU11440

Coolant temperature warning light

“ ”

This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool.

The electrical circuit of the warning light can be checked by turning the key to “ON”.

If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit.

ECA10020

CAUTION:

Do not operate the engine if it is overheated.

EAU42770

Engine trouble warning light “ ”

This warning light comes on when an electrical circuit monitoring the engine is defective. When this occurs, have a Yamaha dealer check the self-diagno- sis system. (See page 3-3 for an explanation of the self-diagnosis device.)

The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit.

EAU42762

Multi-function meter unit

1.Speedometer

2.Odometer/tripmeter/fuel reserve tripmeter/clock

EWA12421

WARNING

Be sure to stop the vehicle before making any setting changes to the multi-function meter unit.

The multi-function meter unit is equipped with the following:

●a speedometer (which shows the riding speed)

●an odometer (which shows the total distance traveled)

●two tripmeters (which show the distance traveled since they were last set to zero)

3-3

INSTRUMENT AND CONTROL FUNCTIONS

●a fuel reserve tripmeter (which shows the distance traveled on the fuel reserve)

●a clock

●a self-diagnosis device

●a brightness control mode

NOTE:

3Be sure to turn the key to “ON” before

using the “SELECT” switch “ /” and “RESET” switch, except for setting the brightness control mode.

1.“SELECT” switch “ / ”

2.“RESET” switch

Speedometer	Odometer, tripmeters, fuel reserve
	tripmeter and clock

1. Speedometer

When the key is turned to “ON”, the speedometer needle will sweep once across the speed range and then return to zero in order to test the electrical circuit.

1.Odometer/tripmeter/fuel reserve tripmeter/clock

Push the “ ” side of the “SELECT” switch to switch the display between the odometer mode “ODO”, the tripmeter modes “TRIP 1” and “TRIP 2” and the clock mode in the following order:

ODO → TRIP 1 → TRIP 2 → Clock → ODO

NOTE:

●Push the “ ” side of the “SELECT” switch to switch the display in the reverse order.

3-4

5. Push the “ ” or “ ” side of the “SELECT” switch to set the minutes.

6. Push the “RESET” switch and then release it to start the clock.

INSTRUMENT AND CONTROL FUNCTIONS

●Push the “RESET” switch for less than one second to display the clock for five seconds, regardless of the currently selected display mode.

If the fuel level warning light comes on (see page 3-2), the odometer display will automatically change to the fuel reserve tripmeter mode “F-TRIP” and start counting the distance traveled from that point. In that case, push the “ ” side of the “SELECT” switch to switch the display between the various tripmeter, odometer, and clock modes in the following order:

F-TRIP → TRIP 1 → TRIP 2 → Clock → ODO → F-TRIP

NOTE:

Push the “ ” side of the “SELECT” switch to switch the display in the reverse order.

To reset a tripmeter, select it by pushing the “ ” or “ ” side of the “SELECT” switch, and then push the “RESET” switch for at least one second. If you do not reset the fuel reserve tripmeter manually, it will reset itself au-

tomatically, and the display will return to the prior mode after refueling and traveling 5 km (3 mi).

To set the clock:

Self-diagnosis devices

This model is equipped with a self-diag-

			nosis device for various electrical cir-		3
			cuits.
			If any of those circuits are defective, the
			engine trouble warning light will come
			on, and then the odometer/tripme-
			ter/clock display will indicate a two-digit
			error code.
1. Clock			If the odometer/tripmeter/clock display
			indicates any error codes, note the
1. Push the “	” or “	” side of the
			code number, and then have a Yamaha
“SELECT” switch to change the			dealer check the vehicle.
display to the clock mode.				ECA11590
2. Push the “ ” side of the “SE-			CAUTION:
LECT” switch and the “RESET”			If the display indicates an error
switch together for at least two			code, the vehicle should be checked
seconds.			as soon as possible in order to avoid
3. When the hour digits start flashing,			engine damage.
push the “	” or “	” side of the

“SELECT” switch to set the hours.

4.Push the “RESET” switch, and the minute digits will start flashing.

3-5

INSTRUMENT AND CONTROL FUNCTIONS

Brightness control mode

1.Speedometer panel

2.Brightness level

This function allows you to adjust the brightness of the speedometer panel to suit the outside lighting conditions.

To set the brightness

1.Turn the key to “OFF”.

2.Push and hold the “ ” side of the “SELECT” switch.

3.Turn the key to “ON”, and then release the “SELECT” switch after five seconds or more.

4.Push the “ ” or “ ” side of the “SELECT” switch to select the desired brightness level.

5.Push the “RESET” switch to confirm the selected brightness level. The display will return to the odometer, tripmeter or clock mode.

EAU12347

Handlebar switches

Left

1.Dimmer switch “/ ”

2.Turn signal switch “/”

3.Horn switch “ ”

3-6

INSTRUMENT AND CONTROL FUNCTIONS

Right

1.Engine stop switch “ /”

2.“SELECT” switch “ / ”

3.“RESET” switch

4.Start switch “”

EAU12400

Dimmer switch “/”

Set this switch to “” for the high beam and to “” for the low beam.

EAU12430

Turn signal switch “/”

To signal a right-hand turn, push this switch to “”. To signal a left-hand turn, push this switch to “”. When released, the switch returns to the center position.

Since this model is equipped with a self-canceling system, the turn signal lights will self-cancel after the vehicle

has traveled both about 150 m (490 ft) and for approximately 15 seconds. However, the turn signal lights can also be canceled manually by pushing the switch in after it has returned to the center position.

NOTE:

The self-canceling system only operates when the vehicle is moving, so that the turn signal lights will not self-cancel while you are stopped at an intersection.

EAU12500

Horn switch “ ”

Press this switch to sound the horn.

EAU12660

Engine stop switch “ /”

Set this switch to “” before starting the engine. Set this switch to “” to stop the engine in case of an emergency, such as when the vehicle overturns or when the throttle cable is stuck.

EAU12710

Start switch “”

Push this switch to crank the engine with the starter.

ECA10050

CAUTION:

See page 5-1 for starting instructions prior to starting the engine.

EAU41700

The engine trouble warning light will come on when the key is turned to “ON”

and the start switch is pushed, but this 3 does not indicate a malfunction.

EAU42522

“SELECT” switch “ /”

This switch is used to perform selections in the odometer, tripmeter and clock mode of the multi-function meter unit.

See “Multi-function meter unit” on page 3-3 for detailed information.

EAU42531

“RESET” switch

This switch is used to perform selections in the odometer, tripmeter and clock mode of the multi-function meter unit.

See “Multi-function meter unit” on page 3-3 for detailed information.

3-7

INSTRUMENT AND CONTROL FUNCTIONS

Clutch lever	EAU12820	EAU12880	EAU12890
Clutch lever	Shift pedal		Brake lever

1. Clutch lever

The clutch lever is located at the left handlebar grip. To disengage the clutch, pull the lever toward the handlebar grip. To engage the clutch, release the lever. The lever should be pulled rapidly and released slowly for smooth clutch operation.

The clutch lever is equipped with a clutch switch, which is part of the ignition circuit cut-off system. (See page 3-15.)

1. Shift pedal

The shift pedal is located on the left side of the engine and is used in combination with the clutch lever when shifting the gears of the 5-speed con- stant-mesh transmission equipped on this motorcycle.

NOTE:

Use your toes or heel to shift up and your toes to shift down.

1. Brake lever

The brake lever is located at the right handlebar grip. To apply the front brake, pull the lever toward the handlebar grip.

3-8

INSTRUMENT AND CONTROL FUNCTIONS

EAU12941	Fuel tank cap	EAU13090
Brake pedal	Fuel tank cap	NOTE:

1. Brake pedal

The brake pedal is on the right side of the motorcycle. To apply the rear brake, press down on the brake pedal.

The fuel tank cap cannot be closed unless the key is in the lock. In addition, the key cannot be removed if the cap is not properly closed and locked.

	EWA11090
WARNING
WARNING		3
Make sure that the fuel tank cap is		3
Make sure that the fuel tank cap is
properly closed before riding.

1.Fuel tank cap lock cover

2.Unlock.

To open the fuel tank cap

Open the fuel tank cap lock cover, insert the key into the lock, and then turn it 1/8 turn clockwise. The lock will be released and the fuel tank cap can be opened.

To close the fuel tank cap

1.Push the fuel tank cap into position with the key inserted in the lock.

2.Turn the key counterclockwise to the original position, remove it, and then close the lock cover.

3-9

INSTRUMENT AND CONTROL FUNCTIONS

EAU13220

Fuel

1.Fuel tank filler tube

2.Fuel level

Make sure that there is sufficient fuel in the tank. When refueling, be sure to insert the pump nozzle into the fuel tank filler hole and to fill the tank to the bottom of the filler tube as shown.

EWA10880

WARNING

●Do not overfill the fuel tank, otherwise it may overflow when the fuel warms up and expands.

●Avoid spilling fuel on the hot engine.

ECA10070

CAUTION:

Immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted surfaces or plastic parts.

EAU13361

Recommended fuel:

UNLEADED GASOLINE ONLY

Fuel tank capacity:

18.5 L (4.89 US gal) (4.07 Imp.gal)

Fuel reserve amount (when the fuel level warning light comes on):

3.7 L (0.98 US gal) (0.81 Imp.gal)

ECA11400

CAUTION:

Use only unleaded gasoline. The use of leaded gasoline will cause severe damage to internal engine parts, such as the valves and piston rings, as well as to the exhaust system.

Your Yamaha engine has been designed to use regular unleaded gasoline with a pump octane number [(R+M)/2] of 86 or higher, or a research octane number of 91 or higher. If

knocking (or pinging) occurs, use a gasoline of a different brand or premium unleaded fuel. Use of unleaded fuel will extend spark plug life and reduce maintenance costs.

Gasohol

There are two types of gasohol: gasohol containing ethanol and that containing methanol. Gasohol containing ethanol can be used if the ethanol content does not exceed 10%. Gasohol containing methanol is not recommended by Yamaha because it can cause damage to the fuel system or vehicle performance problems.

3-10

INSTRUMENT AND CONTROL FUNCTIONS

EAU13431

Catalytic converter

This model is equipped with a catalytic converter in the exhaust system.

EWA10860

WARNING

The exhaust system is hot after operation. Make sure that the exhaust system has cooled down before doing any maintenance work.

ECA10700

CAUTION:

The following precautions must be observed to prevent a fire hazard or other damages.

●Use only unleaded gasoline. The use of leaded gasoline will cause unrepairable damage to the catalytic converter.

●Never park the vehicle near possible fire hazards such as grass or other materials that easily burn.

●Do not allow the engine to idle too long.

EAU42750

Rider seat

To remove the rider seat

1.Insert the key into the seat lock, and then turn it counterclockwise.

1.Seat lock

2.Unlock.

2.Lift the front of the seat up, and then pull the seat off.

To install the rider seat

1.Insert the projection on the rear of the seat into the seat holder as shown.

1.Projection

2.Seat holder

2.Push the front of the seat down to lock it in place.

3.Remove the key.

NOTE:

Make sure that the seat is properly secured before riding.

3-11

INSTRUMENT AND CONTROL FUNCTIONS

Helmet holder

EAU14320	To release the helmet from the hel-
EAU14320
	met holder
	Remove the rider seat, remove the hel-
	met from the helmet holder, and then
	install the seat.

1. Helmet holder

The helmet holder is located under the rider seat.

To secure a helmet to the helmet holder

1.Remove the rider seat. (See page 3-11.)

2.Attach the helmet to the helmet holder, and then securely install the seat.

EWA10160

WARNING

Never ride with a helmet attached to the helmet holder, since the helmet may hit objects, causing loss of control and possibly an accident.

EAU42730

Sidebags

EWA14340

WARNING

Improper loading or overloading can cause loss of control and possibly an accident or personal injury. See pages 1-5 and 6-17 for important loading and tire pressure information.

●Always securely close the sidebags before riding.

●Distribute weight evenly on each side of the motorcycle.

●Do not exceed the load limit of 5 kg (11 lb) for each sidebag.

●Do not exceed the maximum load of 190 kg (419 lb) for the vehicle.

●Do not exceed 120 km/h (80 mi/h) when riding with luggage in the sidebags, otherwise handling could be affected. Improper loading, poor tire or overall motorcycle conditions, poor road surfaces or adverse weather conditions may make it necessary to further reduce the riding speed.

3-12

+ 70 hidden pages