Yamaha RX-V492, RX-V392 User Manual

RX-V492

RX-V392

Natural Sound AV Receiver

Récepteur audiovisuel “Son Naturel”

Receptor AV de Sonido Natural

Thank you for selecting this YAMAHA AV receiver.

Nous vous remercions d’avoir porté votre choix sur ce récepteur audiovisuel YAMAHA.

Muchas gracias por haber adquirido este receptor AV YAMAHA.

OWNER’S MANUAL MODE D’EMPLOI MANUAL DE INSTRUCCIONES

SAFETY INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS

UNIT TO RAIN OR MOISTURE.

1Read Instructions – All the safety and operating instructions should be read before the unit is operated.

2Retain Instructions – The safety and operating instructions should be retained for future reference.

3Heed Warnings – All warnings on the unit and in the operating instructions should be adhered to.

4Follow Instructions – All operating and other instructions should be followed.

5Water and Moisture – The unit should not be used near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc.

6Carts and Stands – The unit should be used only with a cart or stand that is recommended by the manufacturer.

6A A unit and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit and

cart combination to overturn.

7Wall or Ceiling Mounting – The unit should be mounted to a wall or ceiling only as recommended by the manufacturer.

8Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.

9Heat – The unit should be situated away from heat sources such as radiators, stoves, or other appliances that produce heat.

10Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit.

11Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit.

12Cleaning – The unit should be cleaned only as recommended by the manufacturer.

13Nonuse Periods – The power cord of the unit should be unplugged from the outlet when left unused for a long period of time.

14Object and Liquid Entry – Care should be taken so that objects do not fall into and liquids are not spilled into the inside of the unit.

15Damage Requiring Service – The unit should be serviced by qualified service personnel when:

A.The power-supply cord or the plug has been damaged; or

B.Objects have fallen, or liquid has been spilled into the unit; or

C.The unit has been exposed to rain; or

D.The unit does not appear to operate normally or exhibits a marked change in performance; or

E.The unit has been dropped, or the cabinet damaged.

16Servicing – The user should not attempt to service the unit beyond those means described in the operating instructions. All other servicing should be referred to qualified service personnel.

17Power Lines – An outdoor antenna should be located away from power lines.

18Grounding or Polarization – Precautions should be taken so that the grounding or polarization is not defeated.

19For US customers only:

Outdoor Antenna Grounding – If an outside antenna is connected to this unit, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING

MAST	ANTENNA
	LEAD IN
	WIRE
GROUND
CLAMP
	ANTENNA
	DISCHARGE UNIT
	(NEC SECTION 810–20)
ELECTRIC
SERVICE
EQUIPMENT	GROUNDING CONDUCTORS
	(NEC SECTION 810–21)
	GROUND CLAMPS
	POWER SERVICE GROUNDING
	ELECTRODE SYSTEM
	(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE

SPECIAL NOTES FOR FCC COMPOSITE DEVICE (for US customers only)

This device is a composite system. The digital device component may not cause harmful interference.

FCC INFORMATION (for US customers only)

	1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!	Compliance with FCC regulations does not guarantee that
	This product, when installed as indicated in the	interference will not occur in all installations. If this product
	instructions contained in this manual, meets FCC	is found to be the source of interference, which can be
	requirements. Modifications not expressly approved by	determined by turning the unit “OFF” and “ON”, please try
	Yamaha may void your authority, granted by the FCC, to	to eliminate the problem by using one of the following
	use the product.	measures:
	2. IMPORTANT : When connecting this product to	Relocate either this product or the device that is being
	accessories and/or another product use only high quality	affected by the interference.
	shielded cables. Cable/s supplied with this product	Utilize power outlets that are on different branch (circuit
	MUST be used. Follow all installation instructions.
		breaker or fuse) circuits or install AC line filter/s.
	Failure to follow instructions could void your FCC
	authorization to use this product in the USA.	In the case of radio or TV interference, relocate/reorient the
	3. NOTE : This product has been tested and found to	antenna. If the antenna lead-in is 300 ohm ribbon lead,
	comply with the requirements listed in FCC Regulations,	change the lead-in to coaxial type cable.
	Part 15 for Class “B” digital devices. Compliance with	If these corrective measures do not produce satisfactory
	these requirements provides a reasonable level of
		results, please contact the local retailer authorized to
	assurance that your use of this product in a residential
		distribute this type of product. If you can not locate the
	environment will not result in harmful interference with
		appropriate retailer, please contact Yamaha Electronics
	other electronic devices.
		Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
	This equipment generates/uses radio frequencies and, if
		90620.
	not installed and used according to the instructions	The above statements apply ONLY to those products
	found in the users manual, may cause interference
		distributed by Yamaha Corporation of America or its
	harmful to the operation of other electronic devices.
		subsidiaries.

We Want You Listening For A Lifetime (for US customers only)

YAMAHA and the Electronic Industries Association’s	Since hearing damage from loud sounds is often
Consumer Electronics Group want you to get the most out of	undetectable until it is too late, YAMAHA and the
your equipment by playing it at a safe level. One that lets the	Electronic Industries Association’s Consumer
sound come through loud and clear without annoying blaring	Electronics Group recommend you to avoid
or distortion – and, most importantly, without affecting your	prolonged exposure from excessive volume levels.
sensitive hearing.

English

1

CONTENTS

Safety Instructions ...............	Inside the Front Cover
Supplied Accessories ......................................		2
Features ..........................................................		3
Caution ............................................................		4
Notes about the Remote Control Transmitter
........................................................................		5
Profile of This Unit ...........................................		6
Speaker Setup ................................................		7
Connections ....................................................		8
Controls and Their Functions ........................		14

Speaker Balance Adjustment ........................	20
Basic Operations ...........................................	23
Tuning Operations .........................................	26
Preset Tuning ................................................	27
Using Digital Sound Field Processor (DSP)
......................................................................	30
Setting the SLEEP Timer ..............................	34
Troubleshooting .............................................	35
Specifications ................................................	36

SUPPLIED ACCESSORIES

After unpacking, check that the following parts are included.

Indoor FM Antenna

Remote Control Transmitter

	RX-V492					RX-V392
AM Loop Antenna	TIME/	+	DELAY/CENTER		–DELAY TIME+			TEST	EFFECT
–	LEVEL		/REAR	TEST	EFFECT
					ON/OFF	PROGRAM	PROLOGIC ENHANCED		ON/OFF
	PROGRAM		PROLOGIC ENHANCED
							VCR		VIDEO
			VCR	TV/DBS DVD/LD
					DIR A DIR B		REC/PAUSE	PLAY
DIR A DIR B		REC/PAUSE		PLAY
					TAPE			A/B	TAPE
				A/B
–		+			–	PRESET	+ A/B/C/D/E		TUNER
	PRESET		A/B/C/D/E		TUNER
				PLAY			DISC	PLAY	CD
		DISC			CD

			PHONO
		PHONO
		POWER	VOLUME
POWER	VOLUME	SLEEP

SLEEP

Antenna adapter (U.S.A. and Canada models only)

Batteries (size AA, R6, UM-3)

2

FEATURES

●5 Speaker Configuration RX-V492

<U.S.A. and Canada models>

Main: 70W + 70W (8Ω ) RMS Output

Power, 0.04% THD, 20–20,000 Hz Center: 70W (8Ω ) RMS Output

Power, 0.09% THD, 1 kHz Rear: 20W + 20W (8Ω ) RMS Output

Power, 0.7% THD, 1 kHz

<Australia and General models> Main: 65W + 65W (8Ω ) RMS Output

Power, 0.04% THD, 20–20,000 Hz Center: 65W (8Ω ) RMS Output

Power, 0.09% THD, 1 kHz Rear: 20W + 20W (8Ω ) RMS Output

Power, 0.7% THD, 1 kHz RX-V392

<U.S.A. and Canada models>

Main: 50W + 50W (8Ω ) RMS Output

Power, 0.04% THD, 20–20,000 Hz Center: 50W (8Ω ) RMS Output

Power, 0.09% THD, 1 kHz Rear: 20W + 20W (8Ω ) RMS Output

Power, 0.7% THD, 1 kHz

<Australia and General models> Main: 50W + 50W (8Ω ) RMS Output

Power, 0.04% THD, 20–20,000 Hz Center: 50W (8Ω ) RMS Output

Power, 0.09% THD, 1 kHz Rear: 20W + 20W (8Ω ) RMS Output

Power, 0.7% THD, 1 kHz

●Digital Sound Field Processor

●Dolby Pro Logic Surround Decoder

●Theater-like Sound Experience by the Combination of Dolby Pro Logic and YAMAHA DSP Technology (CINEMA DSP)

●Automatic Input Balance Control for Dolby Pro Logic Surround

●Test Tone Generator for Easier Speaker Balance Adjustment

●3 Center Channel Modes (NORMAL/WIDE/PHANTOM)

●40-Station Random Access Preset Tuning

●Automatic Preset Tuning

●Preset Station Shifting Capability (Preset Editing)

●IF Count Direct PLL Synthesizer Tuning System

●Video Signal Input/Output Capability

●SLEEP Timer

●Remote Control Capability

English

3

CAUTION : READ THIS BEFORE OPERATING YOUR UNIT.

1.To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.

2.Install this unit in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose the unit to rain or water.

3.Never open the cabinet. If something drops into the set, contact your dealer.

4.Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power plug and the wires connected to other equipment. Never pull the wires themselves.

5.The openings on the cabinet assure proper ventilation of the unit. If these openings are obstructed, the temperature inside the cabinet will rise rapidly. Therefore, avoid placing objects against these openings, and install the unit in wellventilated condition. Make sure to allow a space of at least 10 cm behind, 20 cm on the both sides and 30 cm above the top panel of the unit. Otherwise it may not only damage the unit, but also cause fire.

6.Always set the VOLUME control to “–∞ ” before starting the audio source play. Increase the volume gradually to an appropriate level after playback has been started.

7.Do not attempt to clean the unit with chemical solvents; this might damage the finish. Use a clean, dry cloth.

8.Be sure to read the “TROUBLESHOOTING” section regarding common operating errors before concluding that the unit is faulty.

9.When not planning to use this unit for long periods of time (ie., vacation, etc.), disconnect the AC power plug from the wall outlet.

10.To prevent lightning damage, disconnect the AC power plug and disconnect the antenna cable when there is an electrical storm.

11.Grounding or polarization – Precautions should be taken so that the grounding or polarization of an appliance is not defeated.

12.AC outlet

Do not connect audio equipment to the AC outlet on the rear panel if that equipment requires more power than the outlet is rated to provide.

13.Voltage Selector (General Model only)

The voltage selector on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply.

Voltages are 110/120/220/240 V AC, 50/60 Hz.

IMPORTANT

Please record the serial number of this unit in the space below.

Serial No.:

The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

FOR CANADIAN CUSTOMERS

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT.

THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCECAUSING EQUIPMENT REGULATIONS.

The apparatus is not disconnected from the AC power source as long as it is connected to the wall outlet, even if the apparatus itself is turned off.

FREQUENCY STEP switch (General Model only)

Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located at the rear) according to the frequency spacing in your area. Before setting this switch, disconnect the AC power plug of this unit from the AC outlet.

4

NOTES ABOUT THE REMOTE CONTROL TRANSMITTER

Battery installation	Remote control transmitter operation range
	RX-V492	RX-V392

English

2

1

3

Battery replacement

If you find that the remote control transmitter must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones.

Notes

●Use only AA, R6, UM-3 batteries for replacement.

●Be sure the polarities are correct. (See the illustration inside the battery compartment.)

●Remove the batteries if the remote control transmitter will not be used for an extended period of time.

●If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

Remote control sensor

Within approximately 6 m (19.7 feet)

30		°
	°	30

Notes

●There should be no large obstacles between the remote control transmitter and the main unit.

●If the remote control sensor is directly illuminated by strong lighting (especially an inverter type of fluorescent lamp etc.), it might cause the remote control transmitter not to work correctly. In this case, reposition the main unit to avoid direct

lighting.

5

PROFILE OF THIS UNIT

You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system, and this unit will sonically transform your room into a wide range of listening environments –movie theater, concert hall, and so on. In addition, you get incredible realism from sources encoded with Dolby Surround using the built-in Dolby Pro Logic Surround Decoder.

Please read this operation manual carefully and store it in a safe place for later reference.

Digital Sound Field Processing

What is it that makes live music so good? Today’s advanced sound reproduction technology lets you get extremely close to the sound of a live performance, but chances are you’ll still notice something missing: the acoustic environment of the live concert hall. Extensive research into the exact nature of the sonic reflections that create the ambience of a large hall has made it possible for Yamaha engineers to bring you this same sound in your own listening room, so you’ll feel all the sound of a live concert.

Furthermore, our technicians, armed with sophisticated measuring equipment, have even made it possible to capture the acoustics of a variety of venues such as an actual concert hall, theater, etc. to allow you to accurately recreate one of several actual live performance environments, all in your own home.

Dolby Pro Logic Surround

This unit employs a Dolby Pro Logic Surround decoder similar to professional Dolby Stereo decoders used in many movie theaters. By using the Dolby Pro Logic Surround decoder, you can experience the dramatic realism and impact of Dolby Surround movie theater sound in your own home. Dolby Pro Logic employs a four channel five speaker system. The Pro Logic Surround system divides the input signal into four levels: the left and right main channels, the center channel (used for dialog), and the rear surround sound channels (used for sound effects, background noise, and other ambient noises). The center channel allows listeners seated in even less-than-ideal positions to hear the dialog originating from the action on the screen while experiencing good stereo imaging.

Dolby Surround is encoded on the sound track of pre-recorded video tapes, laser discs, and some TV/cable broadcasts. When you play a source encoded with Dolby Surround on this unit, the Dolby Pro Logic Surround decoder decodes the signal and distributes the surround-sound effects.

This Dolby Pro Logic Surround Decoder employs a digital signal processing system. This system improves the stability of sound at each channel and minimizes crosstalk between channels, so that positioning of sounds around the room is more accurate compared with conventional analog signal processing systems.

In addition, this unit features a built-in automatic input balance control. This always assures you the best performance without manual adjustment.

Manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby”, the double-D symbol and “Pro Logic” are trademarks of Dolby Laboratories Licensing Corporation.

Dolby Pro Logic Surround + DSP

Dolby Surround sound system shows its full ability in a large movie theater, because movie sounds are originally designed to be reproduced in a large movie theater using many speakers. It is difficult to create a sound environment similar to that of a movie theater in your listening room, because the room size, materials of inside walls, the number of speakers, etc. of your listening room is much different from those of a movie theater.

Yamaha DSP technology made it possible to present you with nearly the same sound experience as that of a large movie theater in your listening room by compensating for lack of presence and dynamics in your listening room with its original digital sound fields combined with Dolby Surround sound field.

The combination of Dolby Pro Logic Surround and DSP is used on the sound field program “ PRO LOGIC ENHANCED”.

CINEMA DSP

The YAMAHA “CINEMA DSP” logo indicates these programs are created by the combination of Dolby Pro Logic and YAMAHA DSP technology.

6

SPEAKER SETUP

SPEAKERS TO BE USED

This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective speakers to use with this unit are main speakers, rear speakers and a center speaker. You may omit the center speaker. (Refer to the “4-Speaker Configuration” shown below.)

The main speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center sounds (dialog etc.) within programs encoded with Dolby Surround. The center speaker needs to be equal in power to the main speakers, although the rear speakers should not be equal. However, all the speakers should have high enough power handling to accept the maximum output of this unit.

SPEAKER CONFIGURATION

5-Speaker Configuration

This configuration is the most effective and recommended one. In this configuration, the center speaker is necessary as well as the rear speakers. If the program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected, conversations will be output from the center speaker and the ambience will be excellent.

•Set the center channel mode to the “NORMAL” or “WIDE” position. (For details, refer to page 21.)

4-Speaker Configuration

The center speaker is not used in this configuration. If the program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected, the center sound is output from the left and the right main speakers. However, the sound effect of other programs can be the same as that of the 5-speaker configuration.

•Be sure to set the center channel mode to the “PHANTOM” position. (For details, refer to page 21.)

FrontMain L

Center

MaiFrontRR

FrontMain L

MaiFrontRR

Dialogue

Dialogue

Surround sound		Surround sound
Rear L	Rear R	Rear L	Rear R

English

SPEAKER PLACEMENT

The recommended speaker configuration, the 5-speaker configuration, will require two speaker pairs: main speakers (your normal stereo speakers), and rear speakers, plus a center speaker. When you place these speakers, refer to the following.

FroMaintRR

Center

MaiFrontLL

TV set

Rear R

Main: In normal position. (The position of your present stereo speaker system.)

Rear: Behind your listening position, facing slightly inward. Nearly six feet (approx. 1.8 m) up from the floor.

Center: Precisely between the main speakers. (To avoid interference with TV sets, use a magnetically shielded speaker.)

Rear L

7

CONNECTIONS

Never plug in this unit and other components until all connections are completed.

CONNECTIONS WITH OTHER COMPONENTS

When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.

*If you have YAMAHA components numbered as 1, 2, 3, etc. on the rear panel, connections can be made easily by making sure to connect the output (or input) terminals of each component to the same-numbered terminals of this unit.

RX-V492

Turntable

Monitor TV

Video cassette recorder

TV/Satellite tuner

OUTPUT

GND

VIDEO IN

VIDEO OUT

AUDIO OUT

VIDEO IN

AUDIO IN

VIDEO OUT

AUDIO OUT

2

*

(U.S.A. model)

IMPEDANCE SELECTOR

REAR

6ΩMIN./SPEAKER

GND

VIDEO SIGNAL

CENTER

SINGLE:6ΩMIN./SPEAKER

DUAL:3ΩMIN./SPEAKER

75Ω

MAIN

A OR B:4ΩMIN./SPEAKER

A B:8ΩMIN./SPEAKER

UNBAL.

MONITOR OUT

DVD/LD

IN

VCROUT

TV/DBS

REAR

8ΩMIN./SPEAKER

CENTER

SINGLE:8ΩMIN./SPEAKER

FM

DUAL:4ΩMIN./SPEAKER

MAIN

A OR B:8ΩMIN./SPEAKER

1

ANT

A B:I6ΩMIN./SPEAKER

GND

* MAINS

AM

ANT

PHONO

TAPE TAPE REC

DVD/LD

IN

VCR OUT

TV/DBS

PB ( MD ) OUT

3

4

AUDIO SIGNAL

1 CD

I20V 60Hz

I00W MAX. TOTAL

SWITCHED

AC OUTLETS

To AC outlet

LINE OUT	LINE IN	VIDEO OUT	AUDIO OUT	OUTPUT
Tape deck,		LD player etc.		CD player
MD recorder, etc.

*1, *2 : See the next page.

8

RX-V392

Turntable		Monitor TV	Video cassette recorder
OUTPUT	GND	VIDEO IN	VIDEO OUT	AUDIO OUT	VIDEO IN	AUDIO IN

2

*	(U.S.A. model)
	IMPEDANCE SELECTOR

	GND	VIDEO SIGNAL
75Ω
UNBAL.	MONITOR OUT	VIDEO	IN VCROUT

FM

ANT

GND
AM
ANT
PHONO	TAPE TAPE REC		VIDEO	IN	VCR OUT
	PB ( MD ) OUT
	3	4
		AUDIO SIGNAL
					1 CD

REAR	6ΩMIN./SPEAKER
CENTER	SINGLE:6ΩMIN./SPEAKER
	DUAL:3ΩMIN./SPEAKER
MAIN	A OR B:4ΩMIN./SPEAKER
	A B:8ΩMIN./SPEAKER
REAR	8ΩMIN./SPEAKER
CENTER	SINGLE:8ΩMIN./SPEAKER
	DUAL:4ΩMIN./SPEAKER
MAIN	A OR B:8ΩMIN./SPEAKER	1
	A B:I6ΩMIN./SPEAKER
		* MAINS
I20V 60Hz
I00W MAX. TOTAL
SWITCHED
AC OUTLETS

English

	LINE OUT	LINE IN	VIDEO OUT	AUDIO OUT
	Tape deck,		LD player etc.
	MD recorder, etc.
	1
	*
	AC OUTLET(S) (SWITCHED)
	(U.S.A., Canada and General models)
	..........................................................		2 SWITCHED OUTLETS
	(Australia model) .................................		1 SWITCHED OUTLET

Use these to connect the power cords from your components to this unit.

The power to the SWITCHED outlets is controlled by this unit’s POWER switch or the provided remote control transmitter’s POWER key. These outlets will supply power to any component whenever this unit is turned on.

The maximum power (total power consumption of components) that can be connected to the SWITCHED AC OUTLET(S) is 100 watts.

To AC outlet

OUTPUT

CD player

2

*GND terminal (For turntable use)

Connecting the ground wire of the turntable to the GND terminal will normally minimize hum, but in some cases better results may be obtained with the ground wire disconnected.

9

CONNECTING SPEAKERS

Subwoofer system

Rear speaker	Rear speaker
Right	Left

Center speaker

(U.S.A. model)

		OUTPUT
REAR		CENTER
CENTER
C	D	SUB
	DUAL	WOOFER
	SINGLE

IMPEDANCE SELECTOR

REAR		6ΩMIN./SPEAKER
CENTER	SINGLE:6ΩMIN./SPEAKER
	DUAL:3ΩMIN./SPEAKER
MAIN	A OR B:4ΩMIN./SPEAKER
	A	B:8ΩMIN./SPEAKER
REAR		8ΩMIN./SPEAKER
CENTER	SINGLE:8ΩMIN./SPEAKER
	DUAL:4ΩMIN./SPEAKER
MAIN	A OR B:8ΩMIN./SPEAKER
	A	B:I6ΩMIN./SPEAKER

	Main speakers B
A	Right
Left
B

Right

Left

MAIN

CAUTION SEE INSTRUCTION MANUAL FOR CORRECT SETTING.

SPEAKERS

Main speakers A

Note

Use speakers with the specified impedance shown on the rear of this unit.

Note on main speaker connections:

One or two speaker systems can be connected to this unit. If you use only one speaker system, connect it to either the SPEAKERS A or B terminals.

Note on center speaker connection:

One or two center speakers can be connected to this unit. If you cannot place the center speaker on or under the TV, it is recommended to use two center speakers and place them on both sides of the TV to orient the center sound at the center position. For connecting two center speakers, follow the method shown below.

Note on a subwoofer connection:

You may wish to add a subwoofer to reinforce low frequencies. Connect the SUBWOOFER OUTPUT terminal of this unit to the INPUT terminal of the subwoofer amplifier, and connect the speaker terminals of the subwoofer amplifier to the subwoofer. With some subwoofers, including the Yamaha Active Servo Processing Subwoofer System, the amplifier and subwoofer are in the same unit.

REAR
CENTER
C	D
	DUAL

SINGLE

Center speaker

Center speaker

10