Yamaha HTR-5950 User Manual

0 (0)

HTR-5950

AV Receiver

OWNER’S MANUAL

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

•Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

1Read Instructions – All the safety and operating instructions should be read before the product is operated.

2Retain Instructions – The safety and operating instructions should be retained for future reference.

3Heed Warnings – All warnings on the product and in the operating instructions should be adhered to.

4Follow Instructions – All operating and use instructions should be followed.

5Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

6Attachments – Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7Water and Moisture – Do not use this product near water – for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to

overturn.

10Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11Power Sources – This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12Grounding or Polarization – This product may be equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

13Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

14Lightning – For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

15Power Lines – An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

17Object and Liquid Entry – Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

18Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a)When the power-supply cord or plug is damaged,

b)If liquid has been spilled, or objects have fallen into the product,

c)If the product has been exposed to rain or water,

d)If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation,

e)If the product has been dropped or damaged in any way, and

f)When the product exhibits a distinct change in perfor-

mance - this indicates a need for service.

20Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

21Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

22Wall or Ceiling Mounting – This unit should be mounted to a wall or ceiling only as recommended by the manufacturer.

23Heat – The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

IMPORTANT SAFETY INSTRUCTIONS

24Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

EXAMPLE OF ANTENNA GROUNDING

MAST	ANTENNA
	LEAD IN
	WIRE
GROUND
CLAMP
	ANTENNA
	DISCHARGE UNIT
	(NEC SECTION 810–20)
ELECTRIC
SERVICE
EQUIPMENT	GROUNDING CONDUCTORS
	GROUNDING CONDUCTORS
	(NEC SECTION 810–21)
	GROUND CLAMPS
	POWER SERVICE GROUNDING
	ELECTRODE SYSTEM
	(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE

FCC INFORMATION (for US customers)

1IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning this unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.

2Install this sound system in a well ventilated, cool, dry, clean place – away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at least 30 cm on the top, 20 cm on the left and right, and 20 cm on the back of this unit.

3Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds.

4Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in a environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.

5Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place:

–other components, as they may cause damage and/or discoloration on the surface of this unit.

–burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury.

–containers with liquid in them, as they may fall and liquid may cause electrical shock to the user and/or damage to this unit.

6Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.

7Do not plug in this unit to a wall outlet until all connections are complete.

8Do not operate this unit upside-down. It may overheat, possibly causing damage.

9Do not use force on switches, knobs and/or cords.

10When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cord.

11Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth.

12Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified.

13To prevent damage by lightning, keep the power cable and outdoor antennas disconnected from a wall outlet or this unit during a lightning storm.

14Do not attempt to modify or fix this unit. Contact qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reasons.

15When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet.

16Install this unit near the AC wall outlet where the power cable plug can be reached easily.

17Be sure to read the “TROUBLESHOOTING” section on common operating errors before concluding that this unit is faulty.

18Before moving this unit, press STANDBY/ON to set this unit to the standby mode, and then disconnect the power cable from the AC wall outlet.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is set to the standby mode. In this state, this unit is designed to consume a very small quantity of power.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to wide slot and fully insert.

This Class B digital apparatus complies with Canadian ICES-003.

IMPORTANT

Please record the serial number of this unit in the space below.

MODEL:

Serial No.:

The serial number is located on the rear panel of this unit. Retain this Owner’s Manual in a safe place for future reference.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing.

Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.

iii

CONTENTS

INTRODUCTION
FEATURES.............................................................	2
GETTING STARTED............................................	3
Supplied accessories ..................................................	3
Installing batteries in the remote control ...................	3
CONTROLS AND FUNCTIONS .........................	4
Front panel .................................................................	4
Remote control...........................................................	6
Front panel display ....................................................	9
Rear panel ................................................................	11
PREPARATION
CONNECTIONS ..................................................	12
Placing speakers.......................................................	12
Connecting speakers ................................................	13
Information on jacks and cable plugs ......................	16
Audio and video signal flow....................................	17
Connecting a TV......................................................	18
Connecting a DVD player, a DVD recorder,
a VCR or an STB.................................................	19
Connecting a CD player, an MD player
or a tape deck.......................................................	21
Connecting a YAMAHA iPod universal dock ........	22
Connecting a multi-format player
or an external decoder .........................................	23
Connecting a game console, a video camera
or a portable audio player....................................	23
Connecting the FM and AM antennas .....................	24
Connecting the power cable.....................................	25
Setting the speaker impedance.................................	26
Turning on this unit or setting it
to the standby mode.............................................	27
BASIC SETUP ......................................................	28
BASIC OPERATION
PLAYBACK..........................................................	31
USING AUDIO FEATURES...............................	33
Using SILENT CINEMA ........................................	33
Muting the audio output...........................................	33
Selecting the night listening mode...........................	33
Selecting the input mode .........................................	34
Using the sleep timer ...............................................	34
Adjusting the speaker level......................................	35
Selecting the Compressed Music
Enhancer mode ....................................................	36
Selecting the MULTI CH INPUT component.........	37
Enjoying multi-channel sources
in 2-channel stereo...............................................	38
Enjoying unprocessed input sources........................	38
Enjoying pure hi-fi stereo sound..............................	38
USING VIDEO FEATURES ...............................	39
Displaying the input source information .................	39
Selecting the OSD mode..........................................	40
Playing video sources in the background ................	40

ENJOYING SURROUND SOUND .....................	41
Enjoying multi-channel sources in surround ...........	41
Enjoying 2-channel sources in surround..................	42
Using Virtual CINEMA DSP ..................................	43
RECORDING........................................................	44
FM/AM TUNING..................................................	45
Automatic tuning .....................................................	45
Manual tuning..........................................................	46
Automatic preset tuning...........................................	47
Manual preset tuning ...............................................	48
Selecting preset stations...........................................	49
Exchanging preset stations ......................................	50
XM® SATELLITE RADIO TUNING.................	52
Connecting the XM Connect-and-Play
digital antenna accessory.....................................	52
XM Satellite Radio controls and functions..............	53
Activating XM Satellite Radio ................................	54
Basic XM Satellite Radio operations.......................	55
Selecting the XM Satellite Radio search mode .......	56
Setting the XM Satellite Radio preset channels ......	60
Displaying the XM Satellite Radio information......	61
SOUND FIELD PROGRAMS
SOUND FIELD PROGRAMS .............................	63
Selecting sound field programs ...............................	63
Sound field program descriptions............................	64
Changing sound field parameter settings.................	66
Sound field program speaker layouts ......................	72
ADVANCED OPERATION
SET MENU ............................................................	75
Using SET MENU...................................................	77
1 SOUND MENU....................................................	78
2 INPUT MENU......................................................	83
3 OPTION MENU...................................................	85
ADVANCED SETUP ............................................	88
REMOTE CONTROL FEATURES ...................	90
Controlling this unit, a TV,
or other components ............................................	90
Setting the remote control code ...............................	92
Setting library codes ................................................	93
Resetting all remote control codes...........................	94
USING iPod® .........................................................	95
Setting the remote control code ...............................	95
Controlling iPod ......................................................	95
RESETTING THE SYSTEM...............................	97
ADDITIONAL INFORMATION
TROUBLESHOOTING .......................................	98
GLOSSARY.........................................................	103
Audio information .................................................	103
Video information..................................................	104
Sound field program information ..........................	105
SPECIFICATIONS.............................................	106

INTRODUCTION


PREPARATION


OPERATION	BASIC


PROGRAMS	FIELD SOUND


OPERATION	ADVANCED


INFORMATION	ADDITIONAL

FEATURES

Built-in 6-channel power amplifier

Minimum RMS output power (0.7% THD, 1 kHz, 8 Ω)

Front: 110 W + 110 W Center: 110 W

Surround: 110 W + 110 W Surround back: 110 W

Sound field programs

Proprietary YAMAHA technology for the creation of sound fields

Dolby Digital/Dolby Digital EX decoder

DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS Neo:6, DTS 96/ 24 decoder

Dolby Pro Logic/Dolby Pro Logic II/ Dolby Pro Logic IIx decoder

Neural Surround decoder (U.S.A. and Canada models only)

Virtual CINEMA DSP

SILENT CINEMA™

Sophisticated AM/FM tuner

40-station random and direct preset tuning

Automatic preset tuning

Preset station shifting capability (preset editing)

XM Satellite Radio (U.S.A. model only)

XM Satellite Radio tuning capability (using the “XM Connect-and-Play digital antenna accessory” sold separately)

Neural Surround decoder to play back the surround sound content of the XM Satellite Radio broadcasts in multichannels, resulting in a full surround sound experience

iPod controlling capability

DOCK terminal to connect a YAMAHA iPod universal dock (such as YDS-10 sold separately), which supports iPod (Click and Wheel), iPod nano, and iPod mini

Other features

192-kHz/24-bit D/A converter

OSD (on-screen display) menus that allow you to optimize this unit to suit your individual audiovisual system

6 additional input jacks for discrete multi-channel input

S-video signal input/output capability

Component video input/output capability

(3 COMPONENT VIDEO INs and 1 MONITOR OUT)

Digital video signal conversion (composite video ↔ S-video → component video) capability for monitor out

Optical and coaxial digital audio signal jacks

Sleep timer

Cinema and music night listening modes

Remote control with preset remote control codes, backlighting input selector buttons, and an iPod (stationed in a YAMAHA iPod universal dock connected to the DOCK terminal) controlling capability

PORTABLE mini analog input jack on the front panel for a portable audio player

Compressed Music Enhancer mode to improve the sound quality of compression artifacts (such as the MP3 format) to that of a high-quality stereo

Notes

•yindicates a tip for your operation.

•Some operations can be performed by using either the buttons on the front panel or the ones on the remote control. In case the button names differ between the front panel and the remote control, the button name on the remote control is given in parentheses.

•This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and product, the product has priority.

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.

Manufactured under license from Digital Theater Systems, Inc. “DTS”, “DTS-ES”, “NEO:6”, and “DTS 96/24” are trademarks of Digital Theater Systems, Inc. Copyright 1996, 2003 Digital Theater Systems, Inc. All right reserved.

iPod®

“iPod” is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.

“SILENT CINEMA” is a trademark of YAMAHA CORPORATION.

The XM name and related logos are registered trademarks of XM Satellite Radio Inc.

Neural Surround™ name and related logos are trademarks owned by Neural Audio Corporation.

GETTING STARTED

Supplied accessories

Check that you received all of the following parts.

Remote control
CODE SET	TRANSMIT			Batteries (2)	AM loop antenna
POWER	POWER	STANDBY	POWER	(AA, R6, UM-3)
TV	AV			(AA, R6, UM-3)
	MD		SLEEP
CD	CD-R	XM
	CBL		MULTI CH IN
DVD	DTV	TUNER
V-AUX	DVR
			AMP
			SOURCE
TV VOL	TV CH	VOLUME
			TV
TV MUTE	TV INPUT	MUTE
STEREO	MUSIC	ENTERTAIN	MOVIE
1	2	3	4
STANDARD SELECT		EXTD SUR.	DIRECT ST.
5	6	7	8	Indoor FM antenna	Indoor FM antenna
9	0	10	ENT.	Indoor FM antenna	Indoor FM antenna
SPEAKERS	ENHANCER	NIGHT	STRAIGHT
LEVEL			SET MENU	(U.S.A., Canada and	(Australia model)
			EFFECT
	PRESET/CH			China models)
BAND			SRCH MODE	China models)
TITLE			MENU
	ENTER
A-E/CAT.		A-E/CAT.
RETURN			DISPLAY
XM MEMORY
REC

AUDIO

DISC SKIP

INTRODUCTION

Installing batteries in the remote control

1Take off the battery compartment cover.

2Insert the two supplied batteries

(AA, R6, UM-3) according to the polarity markings (+ and –) on the inside of the battery compartment.

Notes

•Change all of the batteries if you notice the following conditions:

–the operation range of the remote control decreases.

–the TRANSMIT indicator does not flash or its light becomes dim.

•Do not use an old battery together with a new one.

•Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color.

•If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

•Do not throw away batteries with general house waste; dispose of them correctly in accordance with your local regulations.

•If the remote control is without batteries for more than 2 minutes, or if exhausted batteries remain in the remote control, the contents of the memory may be cleared. When the memory is cleared, insert new batteries, set up the remote control code and program any acquired functions that may have been cleared.

3Snap the battery compartment cover back into place.

CONTROLS AND FUNCTIONS

Front panel

Note

The XM Satellite Radio controlling functions in the following buttons (SEARCH MODE, CATEGORY, PRESET/TUNING/CH l/ h, MEMORY, and DISPLAY) are only applicable to the U.S.A. model and are operational only when “XM” is selected as the input source. For details, see “XM Satellite Radio controls and functions” on page 53.

3 4 5

VOLUME

STANDBY

/ON

PRESET/TUNING

FM/AM

A/B/C/D/E

l PRESET/TUNING/CH h

MEMORY

TUNING MODE

SEARCH MODE

Remote control

This section describes the function of each control on the remote control used to control this unit. To operate other components, see “REMOTE CONTROL FEATURES” on page 90.

Notes

•The XM Satellite Radio controlling functions in the following buttons (XM, XM MEMORY, SRCH MODE, DISPLAY, cursor buttons u/ d/ j/ i, numeric buttons and ENT.) are only applicable to the U.S.A. model and are operational only when “XM” is selected as the input source. For details, see “XM Satellite Radio controls and functions” on page 53.

•The operation mode of the remote control buttons in the shaded area below depends on the component selector switch position. Set the component selector switch to AMP to control this unit. To control the TUNER functions, set the component selector switch to SOURCE and then press TUNER to select “TUNER” as the input source.

CODE SET

TRANSMIT

POWER POWER STANDBY POWER

TV AV

SLEEP

■ Controlling this unit

Set the component selector switch to AMP to control this unit.

1 Infrared window

Outputs infrared control signals. Aim this window at the component you want to operate (see page 8).

CD	CD-R	XM
	CBL	MULTI CH IN

2 CODE SET

3	DVD	DTV	TUNER
	V-AUX	DVR
			AMP
			SOURCE
	TV VOL	TV CH	VOLUME
			TV
	TV MUTE	TV INPUT	MUTE

DUse to set up remote control codes (see page 92).

3 Input selector buttons

ESelect the input source you want to control.

FNote

The corresponding input selector button for the currently selected input source lights up for approximately 5 seconds after you press

Gany buttons on the remote control, showing which source component is currently being operated.

	STEREO	MUSIC	ENTERTAIN	MOVIE		4 Sound field program selector buttons
	1	2	3	4		4 Sound field program selector buttons
4	STANDARD	SELECT	EXTD SUR.	DIRECT ST.		Select sound field programs (see page 63).
	5	6	7	8		– Use SELECT to play back 2-channel sources in
5	SPEAKERS	ENHANCER	NIGHT	STRAIGHT	H	surround (see page 42).
	9	0	10	ENT.		– Use EXTD SUR. to switch between 5.1 and
						– Use EXTD SUR. to switch between 5.1 and
6				EFFECT	I	6.1-channel playback of multi-channel sources
6	LEVEL	PRESET/CH		SET MENU	I	6.1-channel playback of multi-channel sources
7	LEVEL			SET MENU	J	(see page 41).
7	TITLE			MENU	J	(see page 41).
	BAND			SRCH MODE		– Use DIRECT ST. to play back 2-channel sources in
8		ENTER				hi-fi stereo sound (see page 38).
	A-E/CAT.		A-E/CAT.			5 SPEAKERS
9	RETURN			DISPLAY	K	5 SPEAKERS
9	RETURN			DISPLAY	K	Turns on or off the set of front speakers connected to the
	XM MEMORY					Turns on or off the set of front speakers connected to the
	REC					FRONT A and/or B terminals on the rear panel. Press this
				AUDIO		FRONT A and/or B terminals on the rear panel. Press this
				AUDIO		button repeatedly to toggle as follows:
	DISC SKIP					button repeatedly to toggle as follows:
						A on	B on
						A and B off

		6 ENHANCER
		Turns on or off the Compressed Music Enhancer mode
		(see page 36).
		7 LEVEL
	(U.S.A. model)	Selects the speaker channel to be adjusted and sets the
	(U.S.A. model)	output level (see page 35).
		output level (see page 35).

8 Cursor buttons u / d / j / i, ENTER

Select and adjust the sound field program parameters or the “SET MENU” parameters.

9 RETURN

Returns to the previous menu level when adjusting the “SET MENU” parameters.

0 TRANSMIT indicator

Flashes while the remote control is sending infrared signals.

A STANDBY

Sets this unit to the standby mode (see page 27).

B POWER

Turns on this unit (see page 27).

C SLEEP

Sets the sleep timer (see page 34).

D MULTI CH IN

Selects the component connected to the MULTI CH INPUT jacks as the input source when using an external decoder, etc. (see page 37).

E VOLUME +/–

Increases or decreases the volume level.

F Component selector switch

Selects the operation mode of the remote control buttons in the shaded area.

AMP

Operates this unit.

SOURCE

Operates the component selected with an input selector button (see page 91).

Operates the TV assigned to either DTV/CBL or (see page 90).

Notes

•To set the remote control codes for other components, see page 92.

•When you set the remote control codes for both DTV/CBL and

(see page 92), priority is given to the one set for DTV/ CBL.

G MUTE

Mutes the audio output. Press again to restore the audio output to the previous volume level (see page 33).

CONTROLS AND FUNCTIONS

H STRAIGHT (EFFECT)

I NIGHT

Turns on or off the night listening modes (see page 33).

J SET MENU

Enters “SET MENU” (see page 77).

K DISPLAY

Selects the on-screen display (OSD) mode for your video monitor (see page 40).

INTRODUCTION

CONTROLS AND FUNCTIONS

■ Controlling the TUNER functions

Set the component selector switch to SOURCE and then press TUNER to select “TUNER” as the input source.

4 Numeric buttons

Use numbers 1 through 8 to select preset stations.

7 BAND

Switches the reception band between FM and AM (see page 45).

8 Cursor buttons u / d / j/ i

Press j/ ito select a preset station group (A to E) and u/ dto select a preset station number (1 to 8)

(see page 49).

■ Using the remote control

The remote control transmits a directional infrared ray. Be sure to aim the remote control directly at the remote control sensor on this unit during operation.

(U.S.A. model)

Approximately 6 m (20 ft)

30 30

Notes

•Do not spill water or other liquids on the remote control.

•Do not drop the remote control.

•Do not leave or store the remote control in the following types of conditions:

–places of high humidity, such as near a bath

–places of high temperatures, such as near a heater or stove

–places of extremely low temperatures

–dusty places

CONTROLS AND FUNCTIONS

Front panel display

Note

The XM indicator is only applicable to the U.S.A. model and the cursor on the left of the XM indicator lights up only when “XM” is selected as the input source. For details, see “Basic XM Satellite Radio operations” on page 55.

1 2 3 4 5 6 7					8 9	0 A B		C
t	96		pDVR pV-AUX pDTV/CBL pDVD pMD/CD-R pTUNER pCD pXM
	24			DOCK		AUTO TUNED STEREO MEMORY	VOLUME
MATRIX DISCRETE		VIRTUAL	SP	SILENT CINEMA	HiFi DSP
	ENHANCER	STANDARD	A B	NIGHT	HiFi DSP	SLEEP MUTE		dB
q EX	qDIGITAL					ft	96/24	LFE
q PL x q PL q PL						ft	L C R
q PL x q PL q PL						mS	L C R
PCM	neural					mS	SL	SB SR
PCM	neural					dB
D		E F G H			I J	K L M N O

1 Decoder indicators

The respective indicator lights up when any of the decoders of this unit function.

Note

The neural indicator is only applicable to the U.S.A. and Canada models and lights up only when the Neural Surround decoder is selected

(see page 42).

2 ENHANCER indicator

Lights up when the Compressed Music Enhancer mode is turned on (see page 36).

3 Sound field indicators

Light up to indicate the active DSP sound fields.

Presence DSP sound field

	Listening position
Surround left	Surround right
DSP sound field	DSP sound field

Surround back DSP sound field

4 VIRTUAL indicator

Lights up when Virtual CINEMA DSP is active (see page 43).

5 Input source indicators

The corresponding cursor lights up to show the currently selected input source.

6 DOCK indicator

Lights up when you station your iPod in a YAMAHA iPod universal dock (such as YDS-10 sold separately) connected to the DOCK terminal of this unit

(see page 22).

7 SILENT CINEMA indicator

Lights up when headphones are connected and a sound field program is selected (see page 33).

8 CINEMA DSP indicator

Lights up when you select a CINEMA DSP sound field program (see page 64).

9 AUTO indicator

Lights up when this unit is in the automatic tuning mode (see page 45).

0 TUNED indicator

Lights up when this unit is tuned into a station (see page 45).

A STEREO indicator

Lights up when this unit is receiving a strong signal for an FM stereo broadcast while the AUTO indicator is lit

(see page 45).

B MEMORY indicator

Flashes to show that a station can be stored (see page 47).

INTRODUCTION

CONTROLS AND FUNCTIONS

CVOLUME level indicator

Indicates the current volume level.

DPCM indicator

Lights up when this unit is reproducing PCM (Pulse Code Modulation) digital audio signals.

E STANDARD indicator

Lights up when the “SUR. STANDARD” or “SUR. ENHANCED” program is selected (see page 42).

F SP A B indicators

Light up according to the set of front speakers selected.

G Headphones indicator

Lights up when headphones are connected (see page 33).

H NIGHT indicator

Lights up when you select a night listening mode (see page 33).

I HiFi DSP indicator

Lights up when you select a HiFi DSP sound field program (see page 64).

J Multi-information display

Shows the name of the current sound field program and other information when adjusting or changing settings.

K SLEEP indicator

Lights up while the sleep timer is on (see page 34).

L MUTE indicator

Flashes while the MUTE function is on (see page 33).

M 96/24 indicator

Lights up when a DTS 96/24 signal is input to this unit.

N Input channel indicators

Indicate the channel components of the current digital input signal (see page 29).

O LFE indicator

Lights up when the input signal contains the LFE signal.

CONTROLS AND FUNCTIONS

Rear panel

4 5

AUDIO

MULTI CH INPUT

OUTPUT

DIGITAL

DIGITAL INPUT

DOCK

CENTER

OUTPUT

MD/CD-R

DVD

DTV/CBL

DVD

COMPONENT VIDEO

DVD

DVR

MD/

OUT

SUB

(PLAY) CD-R (REC)

FRONT

SURROUND

WOOFER

OPTICAL

COAXIAL

DVD

DTV/CBL

DVR OUT

MONITOR

DVD

DTV/CBL

DVR

OUT

MONITOR

DTV/CBL

MONITOR OUT

VIDEO

OUT

S VIDEO

OUT

TUNER

SPEAKERS

FM ANT

FRONT

SURROUND

75Ω

ANT

GND

UNBAL.

CENTER

SURROUND BACK

(U.S.A. model)

0	A	B
1 Video component jacks		8 DOCK terminal

See pages 18 and 19 for connection information.

2 Audio component jacks

See page 21 for connection information.

3 MULTI CH INPUT jacks

See page 23 for connection information.

4SUBWOOFER OUTPUT jack

See page 13 for connection information.

5DIGITAL OUTPUT jack

See page 21 for connection information.

6 DIGITAL INPUT jacks

See page 19 for connection information.

7 XM jack (U.S.A. model only)

See page 52 for connection information.

Use to connect a YAMAHA iPod universal dock (such as YDS-10 sold separately) where your iPod can be stationed.

See page 22 for connection information.

9 COMPONENT VIDEO jacks

See pages 18 and 19 for connection information.

0 Antenna terminals

See page 24 for connection information.

A Speaker terminals

See page 13 for connection information.

B AC OUTLET(S)

Use to supply power to your other audiovisual components.

See page 25 for details.

INTRODUCTION

CONNECTIONS

Placing speakers

The speaker layout below shows the standard ITU-R* speaker setting. You can use it to enjoy CINEMA DSP and multi-channel audio sources.

*ITU-R is the radio communication sector of the ITU (International Telecommunication Union).

30˚

SL		SR
		60˚
SL	80˚	SR
		SB

FR
FL	SW
FL	SR
C
SL	SB
	1.8 m (6 ft)

Front left and right speakers (FL and FR)

The front speakers are used for the main source sound plus effect sounds. Place these speakers at an equal distance from the ideal listening position. The distance of each speaker from each side of the video monitor should be the same.

Center speaker (C)

The center speaker is for the center channel sounds (dialog, vocals, etc.). If for some reason it is not practical to use a center speaker, you can do without it. Best results, however, are obtained with the full system. Place the center speaker centrally between the front speakers and as close to the monitor as possible, such as directly over or under it.

Surround left and right speakers (SL and SR)

The surround speakers are used for effect and surround sounds. Place these speakers behind your listening position, facing slightly inwards, about 1.8 m (6 ft) above the floor.

Surround back speaker (SB)

The surround back speaker supplements the surround speakers and provides more realistic front-to-back transitions. Place this speaker directly behind the listening position and at the same height as the surround speakers.

Subwoofer (SW)

The use of a subwoofer with a built-in amplifier, such as the YAMAHA Active Servo Processing Subwoofer System, is effective not only for reinforcing bass frequencies from any or all channels, but also for hi-fi stereo sound reproduction of the LFE (low-frequency effect) channel included in Dolby Digital and DTS sources. The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the center of the room to reduce wall reflections.

CONNECTIONS

Connecting speakers

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass.

CAUTION

•Before connecting the speakers, make sure that this unit is set to the standby mode (see page 27).

•Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/or speakers.

•Use magnetically shielded speakers. If this type of speakers still creates the interference with the monitor, place the speakers away from the monitor.

•If you are to use 4 or 6 ohm speakers, be sure to set “SP IMP.” to “6ΩMIN” before using this unit

(see page 26).

Notes

•A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a stripe, groove or ridge. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the plain cable to the “–” (black) terminals.

•The low-frequency signals of other speakers set to “SML” (or “SMALL”) or to “NONE” in “SPEAKER SET” (see pages 78 and 79) are directed to the speakers selected in “LFE/BASS OUT” (see page 79).

Front speakers (A)

	Right	Left
		Surround speakers		Subwoofer
		Right	Left
1	2	4	5	7

PREPARATION

OUTPUT

SUB

WOOFER

SPEAKERS

FRONT

SURROUND

CENTER

SURROUND BACK

(U.S.A. model)

Front	3		6
speakers		Center
(B)		speaker
(B)		speaker	Surround back
			Surround back

speaker

CONNECTIONS

FRONT terminals

Connect one or two front speaker systems (1, 2) to these terminals. If you use only one front speaker system, connect it to the FRONT A or B terminal.

CENTER terminals	1
CENTER terminals		7
Connect a center speaker (3) to these terminals.		7	4
Connect a center speaker (3) to these terminals.	2		4
SURROUND terminals	2
SURROUND terminals	3
Connect surround speakers (4, 5) to these terminals.	5
SURROUND BACK terminals	5		6
SURROUND BACK terminals

Connect a surround back speaker (6) to these terminals.

SUBWOOFER jack

Connect a subwoofer with a built-in amplifier (7) (such as

the YAMAHA Active Servo Processing Subwoofer Speaker layout System) to this jack.

■ Connecting the speaker cable

1Remove approximately 10 mm (0.4 in) of insulation from the end of each speaker cable and then twist the exposed wires of the cable together to prevent short circuits.

10 mm (0.4 in)

CONNECTIONS

■ Connecting the banana plug

The banana plug is a single-pole electrical connector widely used to terminate speaker cables.

Banana plug

1 Tighten the knob.

2 Loosen the knob.

PREPARATION

2 Insert the banana plug connector into the

end of the corresponding terminal.

Red: positive (+) Black: negative (–)

3 Insert one bare wire into the hole on the side of each terminal.

Red: positive (+)

Black: negative (–)

4 Tighten the knob to secure the wire.

Red: positive (+)

Black: negative (–)

CONNECTIONS

Information on jacks and cable plugs

Note

You can use the digital jacks to input PCM, Dolby Digital and DTS bitstreams. When you connect components to both the COAXIAL and OPTICAL jacks, priority is given to the signals input at the COAXIAL jack. All digital input jacks are compatible with 96-kHz sampling digital signals.

Audio jacks and cable plugs

Video jacks and cable plugs

AUDIO		DIGITAL AUDIO	DIGITAL AUDIO	PORTABLE
L	R	COAXIAL	OPTICAL
(White)	(Red)	(Orange)
L	R	C	O	M
L	R	C

Left and right		Coaxial	Optical	Stereo
analog audio		digital audio	digital	analog
cable plugs		cable plug	audio cable	audio
			plug	mini cable
				plug

		COMPONENT VIDEO
VIDEO	S VIDEO	Y	PB	PR

(Yellow)		(Green)	(Blue)	(Red)
V	S	Y	PB	PR
V		Y	PB	PR
Composite	S-video	Component
video cable	cable plug		video cable
plug			plugs

■ Audio jacks

This unit has four types of audio jacks. Connection depends on the availability of audio jacks on your other components.

AUDIO jacks

For conventional analog audio signals transmitted via left and right analog audio cables. Connect red plugs to the right jacks and white plugs to the left jacks.

DIGITAL AUDIO COAXIAL jacks

For digital audio signals transmitted via coaxial digital audio cables.

DIGITAL AUDIO OPTICAL jacks

For digital audio signals transmitted via optical digital audio cables.

Note

Pull out the cap from the optical jack before you connect the fiber optic cable. Do not discard the cap. When you are not using the optical jack, be sure to put the cap back in place. This cap protects the jack from dust.

■ Video jacks

This unit has three types of video jacks. Connection depends on the availability of input jacks on your video monitor. When “VIDEO CONV.” is set to “ON” (see page 85), the video signals input at the VIDEO and S VIDEO jacks are converted and output at the VIDEO, S VIDEO and COMPONENT VIDEO jacks interchangeably.

VIDEO jacks

For conventional composite video signals transmitted via composite video cables.

S VIDEO jacks

For S-video signals, separated into the luminance (Y) and chrominance (C) video signals transmitted on separate wires of S-video cables.

COMPONENT VIDEO jacks

For component video signals, separated into the luminance (Y) and chrominance (PB, PR) video signals transmitted on separate wires of component video cables.

PORTABLE jack

For analog audio signals transmitted via stereo analog audio mini cables.

CONNECTIONS

Audio and video signal flow

■ Audio signal flow for AUDIO OUT (REC)

Input	Output
	AUDIO OUT (REC)

DIGITAL AUDIO

COAXIAL

Digital audio

DIGITAL AUDIO

OPTICAL

L R L R

AUDIO

Analog audio

PORTABLE

Digital output

Analog output

Note

This unit handles digital and analog signals independently. Thus, audio signals input at the analog jacks are output only at the analog AUDIO OUT (REC) jacks. Likewise, audio signals input at the DIGITAL INPUT (OPTICAL or COAXIAL) jacks are output only at the DIGITAL OUTPUT jack.

■ Video signal flow for MONITOR OUT

Input	Output
Input	(MONITOR OUT)
Y PB PR	Y PB PR
COMPONENT
VIDEO
S VIDEO	Analog video

VIDEO

Through

Video conversion when “VIDEO CONV.” is set to “ON” (see page 85)

PREPARATION

Note

When video signals are input at the COMPONENT VIDEO, S VIDEO and VIDEO jacks, the priority order of the input signals is as follows where the video signals input at the COMPONENT VIDEO jacks have the top priority:

COMPONENT VIDEO > S VIDEO > VIDEO

CONNECTIONS

Connecting a TV

Connect your TV to the VIDEO MONITOR OUT jack, the S VIDEO MONITOR OUT jack or the COMPONENT VIDEO MONITOR OUT jacks of this unit.

CAUTION

Do not connect this unit or other components to the AC power supply until all connections between components are complete.

(U.S.A. model)

	COMPONENT VIDEO
	Y	PB	PR
MONITOR	MONITOR	MONITOR OUT
OUT	OUT
VIDEO	S VIDEO

V	S	Y	PB	PR
V
		S-video in
Video in		Component video in
Video in
	TV

CONNECTIONS

Connecting a DVD player, a DVD recorder, a VCR or an STB

Connect your DVD player, DVD recorder, VCR or STB (set-top box) using the same type of video connections as those made for your TV (see page 18). The cable TV receiver and the satellite receiver are examples of the STB.

CAUTION

Do not connect this unit or other components to the AC power supply until all connections between components are complete.

Notes

	• When “VIDEO CONV.” is set to “OFF” (see page 85), be sure to make the same type of video connections as those made for your TV

	(see page 18). For example, if you connected your TV to the VIDEO MONITOR OUT jack of this unit, connect your other	PREPARATION
	components to the VIDEO jacks.	PREPARATION
	components to the VIDEO jacks.
	• When “VIDEO CONV.” is set to “ON” (see page 85), the converted video signals are output only at the MONITOR OUT jacks. When
	recording a source, you must make the same type of video connections between each component.
	• To make a digital connection to a component other than the default component assigned to each DIGITAL INPUT or DIGITAL
	OUTPUT jack, select the corresponding setting for “OPTICAL OUT”, “OPTICAL IN”, or “COAXIAL IN” in “I/O ASSIGNMENT”
	(see page 83).
	• If you connect your DVD player to both the DIGITAL INPUT (OPTICAL) and the DIGITAL INPUT (COAXIAL) jacks, priority is

	given to the signals input at the DIGITAL INPUT (COAXIAL) jack.

■ Connecting a DVD player

DVD player

Audio out

R L	Videoout	video-S out
	V	S
		S
AUDIO

		Component video out
O	audio out	C	audio out	Y	PB	PR
O	Optical	C	Coaxial	Y	PB	PR
	Optical		Coaxial			(U.S.A. model)
DIGITAL INPUT
DVD		DVD
						COMPONENT VIDEO
						DVD
					Y	PB PR
OPTICAL		COAXIAL

DVD	DVD
VIDEO	S VIDEO

CONNECTIONS

■ Connecting a DVD recorder or a VCR

AUDIO

IN DVR OUT	IN DVR OUT
VIDEO	S VIDEO

out	R L	in	R	L	out	V	in	V
Audio		Audio			Video		Video

(U.S.A. model)

COMPONENT VIDEO

DVR

Y PB PR

out	S	in	S
video-S		video-S
			Y	PB	PR

DVD recorder or

VCR

■ Connecting an STB

Cable TV receiver or satellite receiver

Audioout	Videoout	video-S out
R L	V	S
		S

	O	audio out
	O	Optical
		Optical

Component video out

Y PB PR

(U.S.A. model)

AUDIO

DIGITAL INPUT

DTV/CBL

COMPONENT VIDEO

		Y	PB	PR
		OPTICAL
DTV/CBL	DTV/CBL		DTV/CBL
VIDEO		S VIDEO

CONNECTIONS

Connecting a CD player, an MD player or a tape deck

Connect your CD player, MD player or tape deck via analog and/or digital connections.

CAUTION

Do not connect this unit or other components to the AC power supply until all connections between components are complete.

Note

To make a digital connection to a component other than the default component assigned to each DIGITAL INPUT or DIGITAL OUTPUT jack, select the corresponding setting for “OPTICAL OUT”, “OPTICAL IN”, or “COAXIAL IN” in “I/O ASSIGNMENT” (see page 83).

CD player

Audio out

R	L
							(U.S.A. model)
		AUDIO				DIGITAL	DIGITAL INPUT
						OUTPUT
						MD/CD-R MD/CD-R
		IN MD/	OUT			OPTICAL	OPTICAL
	CD	(PLAY) CD-R (REC)				OPTICAL	OPTICAL
						in	out
						Opticalaudio	Opticalaudio
Audio out	R	L	R	L	Audio in	O	O
Audio out	R	L	R	L	Audio in

MD recorder or tape deck

PREPARATION

CONNECTIONS

Connecting a YAMAHA iPod universal dock

This unit is equipped with the DOCK terminal on the rear panel that allows you to connect a YAMAHA iPod universal dock (such as YDS-10 sold separately) where you can station your iPod and control playback of your iPod using the supplied remote control. Connect a YAMAHA iPod universal dock (such as YDS-10 sold separately) to the DOCK terminal on the rear panel of this unit using its dedicated cable. Once the connection is complete, station your iPod in the YAMAHA iPod universal dock.

CAUTION

Do not connect this unit or other components to the AC power supply until all connections between components are complete.

Notes

•Only iPod (Click and Wheel), iPod nano, and iPod mini are supported.

•You need a YAMAHA iPod universal dock (such as YDS-10 sold separately) and its dedicated cable compatible with the DOCK terminal of this unit.

•Once your iPod is stationed in a YAMAHA iPod universal dock (such as YDS-10 sold separately) connected to the DOCK terminal of this unit, this unit begins the signal transmission with your iPod.

•Once the connection between your iPod and this unit is complete, “iPod connected” appears in the front panel display and the DOCK indicator lights up in the front panel display. If the connection between your iPod and this unit fails, a status message appears in the front panel display. For a complete list of connection status messages, see the iPod section in “TROUBLESHOOTING” on page 102.

•Only analog audio and video signals of your iPod are input at the DOCK terminal, and the analog audio signals can be output at the analog AUDIO OUT (REC) jacks for recording.

•Your iPod battery is automatically charged when your iPod is stationed in a YAMAHA iPod universal dock (such as YDS-10 sold separately) connected to the DOCK terminal of this unit as long as this unit is turned on.

•Depending on the type of iPod, you may need to insert one of the iPod adapters supplied with a YAMAHA iPod universal dock (such as YDS-10 sold separately) into the dock slot before you station your iPod.

iPod

YAMAHA iPod universal dock

(such as YDS-10 sold separately)

(U.S.A. model)

DOCK

Connecting a multi-format player or an external decoder

This unit is equipped with 6 additional input jacks (FRONT L/R, CENTER, SURROUND L/R and SUBWOOFER) for discrete multi-channel input from a multi-format player, external decoder or sound processor. Connect the output jacks on your multi-format player or external decoder to the MULTI CH INPUT jacks. Be sure to match the left and right output jacks to the left and right input jacks for the front and surround channels.

CAUTION

Do not connect this unit or other components to the AC power supply until all connections between components are complete.

Notes

•When you select the component connected to the MULTI CH INPUT jacks as the input source (see page 37), this unit automatically turns off the digital sound field processor, and you cannot select sound field programs.

•This unit does not redirect signals input at the MULTI CH INPUT jacks to accommodate for missing speakers. We recommend that you connect at least a 5.1-channel speaker system before using this feature.

•When headphones are used, signals are output only from the front left and right channels.

MULTI CH INPUT

CENTER

SUB

FRONT SURROUND WOOFER

L	R	L	R	Subwooferout
Front out	Surroundout			Subwooferout	Centerout

CONNECTIONS

Connecting a game console, a video camera or a portable audio player

Use the VIDEO AUX jacks on the front panel to connect a game console, a video camera or a portable audio player to this unit.

CAUTION

Be sure to turn off the volume of this unit and other components before making connections.

Notes

•The audio signals input at the PORTABLE mini jack take priority over the ones input at the AUDIO L/R jacks.

•The audio signals input at the DOCK terminal takes priority over the ones input at the VIDEO AUX jacks.

(U.S.A. model)

									VOLUME
STANDBY
/ON
			PRESET/TUNING	FM/AM	A/B/C/D/E	l PRESET/TUNING/CH h	MEMORY	TUNING MODE
							INPUT
PHONES	SPEAKERS		STRAIGHT	l	PROGRAM h				VIDEO AUX
	A	B				INPUT MODE		MULTI CH
								INPUT
			TONE CONTROL	BASS/TREBLE
SILENT CINEMA								VIDEO	L AUDIO R	PORTABLE

VIDEO AUX

				M
	VIDEO		L AUDIO R	PORTABLE
out	V	L	out L/R	Audio out
Video	V	L	Audio	R
Video			Audio

Game console or	Portable audio
video camera	player

PREPARATION

Multi-format player or external decoder

CONNECTIONS

Connecting the FM and AM antennas

Both FM and AM indoor antennas are supplied with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals.

Notes

2Press and hold the tab of the AM ANT terminal.

•The AM loop antenna should be placed away from this unit.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

•A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized YAMAHA dealer or service center about outdoor antennas.

3Insert one of the AM loop antenna lead wires into the AM ANT terminal.

AM loop antenna (supplied)

Indoor FM antenna (supplied)

(U.S.A. model)

	TUNER
AM		FM ANT
AM		75Ω
ANT	GND	UNBAL.

Ground (GND terminal)

For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

Outdoor AM antenna

Use a 5 to 10 m (16.4 to 32.8 ft) of vinyl-covered wire extended outdoors from a window.

4Release the tab of the AM ANT terminal back into place.

■ Connecting the AM loop antenna

1 Set up the AM loop antenna.

5Repeat steps 2 through 4 to connect the other lead wire to the GND terminal.

Once you have properly connected the AM loop antenna to this unit, orient the AM loop antenna for the best reception when you tune into AM stations (see page 45).

CONNECTIONS

Connecting the power cable

Once all connections are complete, plug the power cable into the AC wall outlet.

(U.S.A. model)

AC OUTLETS

To the AC wall outlet

■ AC OUTLET(S) (SWITCHED)

Australia model	...................................................... 1 outlet
Other models.........................................................	2 outlets

Use these outlet(s) to supply power to any connected components. Connect the power cable of your other components to these outlet(s). Power to these outlet(s) is supplied when this unit is turned on. However, power to these outlet(s) is cut off when this unit is set to the standby mode. For information on the maximum power or the total power consumption of the components that can be connected to these outlet(s), see “SPECIFICATIONS” on page 106.

Memory back-up

The memory back-up circuit prevents the stored data from being lost even if this unit is in the standby mode. However, the stored data will be lost in case the power cable is disconnected from the AC wall outlet or if the power supply is cut off for more than one week.

PREPARATION

CONNECTIONS

Setting the speaker impedance

CAUTION

If you are to use 4 or 6 ohm speakers, set “SP IMP.” to “6ΩMIN” as follows BEFORE using this unit.

2,5

(U.S.A. model)

									VOLUME
STANDBY
/ON
			PRESET/TUNING	FM/AM	A/B/C/D/E	l PRESET/TUNING/CH h	MEMORY	TUNING MODE
							INPUT
PHONES	SPEAKERS		STRAIGHT	l	PROGRAM h				VIDEO AUX
	A	B				INPUT MODE		MULTI CH
								INPUT
			TONE CONTROL	BASS/TREBLE
SILENT CINEMA								VIDEO	L AUDIO R	PORTABLE

2,4 3

1Make sure this unit is set to the standby mode.

See page 27 for details about turning on this unit or setting it to the standby mode.

2Press and hold STRAIGHT (EFFECT) on the front panel and then press STANDBY/ON to turn on this unit.

This unit turns on, and the advanced setup menu appears in the front panel display.

While holding down

STRAIGHT

STANDBY /ON

EFFECT

3Press PROGRAM l/ h on the front panel repeatedly to select “SP IMP.”.

The following display appears in the front panel display.

l PROGRAM h

SP IMP.-8 MIN

4Press STRAIGHT (EFFECT) on the front panel repeatedly to select “6ΩMIN”.

The following display appears in the front panel display.

STRAIGHT

EFFECT

SP IMP.-6 MIN

5Press STANDBY/ON on the front panel to save the new setting and set this unit to the standby mode.

STANDBY /ON

Note

The setting you made is reflected next time you turn on this unit.

+ 86 hidden pages