Yamaha EMX5000 User Manual

0 (0)

Owner’s Manual

Keep This Manual For Future Reference.

■

The Owner’s Manual Revisions

Thank you for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. Parts of the EMX5000-20, EMX5000-12 owner’s manual have been revised. Please refer to the following revisions rather than the corresponding sections of the original owner’s manual.

P.14

POWER amp section

P.18

Rear panel

SPEAKERS (speaker output) jacks

These jacks are used to connect speakers. Jacks 1 are Speakon-type connectors. Use only Neutrik NL4FC plugs for connecting Speakon connectors.

CHANNEL A

STEREO/PARALLEL BRIDGE

LIMITER indicator

If the output level of signals received at the SPEAKERS jacks (output of the internal power ampliﬁer) reaches maximum, the indicator will light.

Caution: If the LIMITER indicator flashes continuous-

ly, the internal power amplifier section is being excessively overloaded and may malfunction. Reduce the output level at the ST OUT fader (K) below the level that the indicator flashes only briefly on the highest transient peaks.

2–

1+ A+ 1– A–

1–

Neutrik NL4FC

2+ B+ 2– B–

CHANNEL B

1+ B+ 1– B–

Jacks 2 are 1/4”phone jacks. The setting of the control panel power amp select switch Y will determine the signal that is output to these jacks, and the number and appropriate impedance of the speakers that can be connected.

1+ + 1– 2+ – 2–

P.15

Other indicators and controls

Level Meter

This LED display shows the level of signals received at the ST OUT jack (input/output panel 0).

Note:

The SPEAKERS 1 & 2 jacks (rear panel 3) output the signals received at the ST OUT jack via the internal power amplifier. Check the output signal level via the LIMITER indicator (X). The LIMITER indicator will light before the Level Meter “8” or “PEAK” LED light.

P.33

Block/Level Diagram

SPEAKERS OUT

MAXIMUM OUTPUT [500W/4Ω]

NOMINAL OUTPUT [100W/4Ω]

+11dB

+4dB

Power Ampliﬁer output section level diagram (bottom right)

These plots show the nominal output and maximum output levels of signals received at the SPEAKERS jacks. If the output level is +4dB (Level Meter “0”), the internal power ampliﬁer will deliver 100W into a 4 Ω load. If the output level is +11dB (LIMITER indicator lights), the internal ampliﬁer will deliver a maximum of 500W into 4Ω.

+30dB

+20dB

+10dB

0dB

EMX5000-20/EMX5000-12

Block/Level Diagram

YSP

YAMAHA

SPEAKER

PROCESSING

POWER AMP IN

[+4dB]

PEAK

ST SUB OUT

[+4dB]

[–6dB]

ST SUB OUT

REC OUT

[–10dBV]

EMX5000-12:CH1-8

EMX5000-20:CH1-16

STAND-BY

[0dB]

SUM

PFL R / AFL R PFL L / AFL L

AUX2 (MUTE) AUX1 (MUTE) EFFECT2 (MUTE) EFFECT1 (MUTE) STEREO R (MUTE) STEREO L (MUTE)

AUX2 (NON-MUTE) AUX1 (NON-MUTE) EFFECT2 (NON-MUTE) EFFECT1 (NON-MUTE) STEREO R (NON-MUTE) STEREO L (NON-MUTE)

ST OUT

[+4dB]

[–10dB]

ST OUT

GEQ

16kHz 8kHz 4kHz 2kHz 1kHz

500Hz

250Hz

9-Stage GEQ

125Hz 63Hz

[0dB]

SUM

[0dB]

SUM

PEAK

9-Stage GEQ

SUM

PFL

AFL

SUM

LIMITTER

+40dB

+30dB

+20dB

+10dB

0dB

–10dB

–20dB

–30dB

–40dB

–50dB

SPEAKERS

[500Wmax@4ohms]

BRIDGE

–2

PROTECTOR

LIMITTER

Power Select

MONO

MAIN R

Signal Select

500W

300W

AUX2

MONO BRIDGE

+1–1+2

100W

INV

MONO OUT

INV

[–10dB]

LPF

MONO OUT

SUM

–2

POWER AMP Controls

[+4dB]

80–120Hz

(12dB/oct)

LPF

FREQ

AFL

SPEAKERS OUT

NOMINAL OUTPUT [100W/4Ω]

MAXIMUM OUTPUT [500W/4Ω]

[PHONES 3mW@40ohms]

ST OUT•ST SUB OUT•MONO OUT [+4dB]

AUX SEND, EFFECT SEND [+4dB]

EFFECT SEND1

[+4dB]

EFFECT SEND2

[+4dB]

PHONES

AUX SEND1

[+4dB]

AUX SEND2

[+4dB]

[–10dB]

AUX1

[0dB]

SUM

[0dB]

SUM

[–10dB]

AUX2

[0dB]

SUM

AFL

[0dB]

SUM

INV

[–6dB]

SUMSUM

[0dB]

INV

AFL

[3mW@40ohms]

ST•MONO•AUX fader [–10dB]

INV

[–16dB]

PHONES

[–6dB]

SUM

[0dB]

SUM

[0dB]

INV

SUM

ST SUB level control [–6dB]

EFFECT [–6dB]

REC OUT [–10dBV]

CH & ST CH to AUX/EFFECT [–6dB]

ST SUB IN to ST/AUX [–6dB]

2TR IN to ST [–6dB]

+1–1+2

500W

300W

100W

AUX1

MAIN L

MONO BRIDGE

–60dB

PHONES [–16dB]

[–6dB]

[0dB]

PAN

EFFECT1

EFFECT2

[0dB]

[–10dB]

CH Fader

PEAK

SIGNAL

[0dB]

Hi Gain

Mid Gain

Mid f

Lo Gain

3-Stage EQ

HPF

[0dB]

+48V

[–60~–16dB]

[–34~+10dB]

GAIN

EMX5000-12:[CH1-8]

EMX5000-20:[CH1-8] [CH9-16]

PHANTOM

8CH/SW

PAD

26dB

EMX5000-12:CH1-8

CH INSERT I/O

[0dB]

EMX5000-12:CH1-8

EMX5000-20:CH1-16

CH INPUT

[–60~–16dB]

[–34~+10dB]

EMX5000-20/EMX5000-12

[–6dB]

AUX1

AUX2

POST

EMX5000-20:CH1-16

[0dB]

[–6dB]

PFL

BAL

POST

[0dB]

[–10dB]

ST CH Fader

PEAK

[0dB]

Mid

3-Stage EQ

[0dB]

GAIN

ST CH INPUT

[–6dB]

AUX1

EFFECT1

EFFECT2

POST

SIGNAL

3-Stage EQ

[–34~+10dB]

EMX5000-12:CH9(L)/10(R),CH11(L)/12(R)

EMX5000-20:CH17(L)/18(R),CH19(L)/20(R)

[–34~+10dB]

AUX2

POST

[–6dB]

PFL

[0dB]

PAD

[+4dB] [–6dB]

L (MONO)

ST SUB IN 1,2

AUX1STAUX2

PAD

[+4dB]

[–6dB]

PFL

[0dB]

2TR IN

[–10dBV]

[–16dB]

[–6dB]

[–12dB]

EFFECT1 RTN

AUX1

AUX2

L OUT

R OUT

DIGITAL

EFFECT1

PROGRAM

PARAMETER

[–12dB]

[–16dB]

EFFECT2 RTN

PFL

[–6dB]

L OUT

R OUT

DIGITAL

EFFECT2

PROGRAM

PARAMETER

PFL

AUX1

AUX2

TAP

ON/OFF

FOOT SWITCH

0dB=0.775V

0dBV=1V

+30dB

ST CH INPUT

GAIN Min. [+10dB]

+20dB

CH & ST CH to ST [0dB] (PAN, BAL turned hard left/right)

2TR IN [–10dBV]

ST SUB IN [+4dB]

0dB

+10dB

fader [–10dB]

CH INPUT A, B GAIN Min. [–16dB]

–10dB

–20dB

ST CH INPUT

GAIN Max. [–34dB]

–30dB

–40dB

CH INPUT A, B

GAIN Max. [–60dB]

–50dB

–60dB

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA 90620

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

• Explanation of Graphical Symbols

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The above warning is located on the rear of the unit.

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured GREEN and YELLOW.

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

* This applies only to products distributed by YAMAHA KEMBLE

MUSIC (U.K.) LTD.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

European Specifications Only

This mark indicates a dangerous electrically live terminal. When connecting an external wire to this terminal, it is necessary either to have “a person who have received appropriate guidance on handling” make the connection or to use leads or a cord that have been manufactured in such a way

that the connection can be made simply and without problem.

Precautions

WARNING

Installation

• Connect this unit’s power cord only to an AC outlet of the type stated in this Owner’s Manual or as marked on the unit. Failure to do so is a ﬁre and electrical shock hazard.

• Do not allow water to enter this unit or allow the unit to become wet. Fire or electrical shock may result.

• Do not place a container with liquid or small metal objects on top of this unit. Liquid or metal objects inside this unit are a ﬁre and electrical shock hazard.

• Do not place heavy objects, including this unit, on top of the power cord. A damaged power cord is a ﬁre and electrical shock hazard. In particular, be careful not to place heavy objects on a power cord covered by a carpet.

• Use only the included power cord for this unit. Using other types may be a ﬁre and electrical shock hazard.

• The power to this device is not completely shut off even when the power switch is turned off. Locate the device close to the AC outlet so you can easily reach the power plug.

Precautions

Operation

• Do not scratch, bend, twist, pull, or heat the power cord. A damaged power cord is a ﬁre and electrical shock hazard.

• Do not remove the unit’s cover. You could receive an electrical shock. If you think internal inspection, maintenance, or repair is necessary, contact your dealer.

• Do not modify the unit. Doing so is a ﬁre and electrical shock hazard.

• If lightning begins to occur, turn off the power switch of the unit as soon as possible, and unplug the power cable plug from the electrical outlet.

• If there is a possibility of lightning, do not touch the power cable plug if it is still connected. Doing so may be an electrical shock hazard.

In case an abnormality occurs during operation

• If the power cord is damaged (i.e., cut or a bare wire is exposed), ask your dealer for a replacement. Using the unit with a damaged power cord is a ﬁre and electrical shock hazard.

• Should this unit be dropped or the cabinet be damaged, turn the power switch off, remove the power plug from the AC outlet, and contact your dealer. If you continue using the unit without heeding this instruction, ﬁre or electrical shock may result.

• If you notice any abnormality, such as smoke, odor, or noise, or if a foreign object or liquid gets inside the unit, turn it off immediately. Remove the power cord from the AC outlet. Consult your dealer for repair. Using the unit in this condition is a ﬁre and electrical shock hazard.

CAUTION

Installation

• Keep this unit away from the following locations:

- Locations exposed to oil splashes or steam, such as near cooking stoves, humidiﬁers, etc.

- Unstable surfaces, such as a wobbly table or slope.

- Locations exposed to excessive heat, such as inside a car with all the windows closed, or places that receive direct sunlight.

- Locations subject to excessive humidity or dust accumulation.

• Hold the power cord plug when disconnecting it from an AC outlet. Never pull the cord. A damaged power cord is a potential ﬁre and electrical shock hazard.

• Do not touch the power plug with wet hands. Doing so is a potential electrical shock hazard.

• This unit has ventilation holes at the rear to prevent the internal temperature rising too high. Do not block them. Blocked ventilation holes are a ﬁre hazard.

• To relocate the unit, turn the power switch off, remove the power plug from the AC outlet, and remove all connecting cables. Damaged cables may cause ﬁre or electrical shock.

Operation

• Turn off all musical instruments, audio equipment, and speakers when connecting to this unit. Use the correct connecting cables and connect as speciﬁed.

• Always lower the volume control to minimum before turning on the power to this unit. A sudden blast of sound may damage your hearing.

• Use only speaker cables when connecting speakers to ampliﬁer outputs. Using other types of cables is a ﬁre hazard.

• If you know you will not use this unit for a long period of time, such as when going on vacation, remove the power plug from the AC outlet. Leaving it connected is a potential ﬁre hazard.

Maintenance

• Clean the contacts of the phone plug before connecting it to the SPEAKERS jack of this unit. Dirty contacts may generate heat.

• To prevent electrical shock when cleaning the unit, remove the power plug from the AC outlet.

EMX5000-20/EMX5000-12—Owner’s Manual

Precautions

PRECAUTIONS FOR OPERATION – FOR CORRECT OPERATION –

Connector pin assignments

• XLR-type connectors are wired as follows: pin 1: ground, pin 2: hot (+), and pin 3: cold (–).

• Insert TRS phone jacks are wired as follows: sleeve: ground, tip: send, and ring: return.

Replacing abrasive parts

• The performance of components with moving contacts, such switches, rotary controls, faders, and connectors, deteriorates over time. The rate of deterioration depends on the operating environment and is unavoidable. Consult your dealer about replacing defective components.

Influence on cell phone usage

• Using a cell phone (mobile telephone) near this unit may induce noise. If noise occurs, use the telephone away from the unit.

Volume level setting

• Do not set all equalizer controls and faders to maximum. Doing so may cause oscillation depending on the condition of the connected unit and speakers, and may damage the speakers.

Interference with other electronic devices

• The digital circuits of this unit may induce a slight noise into nearby radios and TVs. If noise occurs, relocate the affected equipment.

EMX5000-20/EMX5000-12—Owner’s Manual

+ 13 hidden pages