POWERED SPEAKER HAUT-PARLEUR ALIMENTÉ AKTIVLAUSPRECHER ALTAVOZ INTEGRADO ALTOPARLANTE ATTIVO ACTIEVE LUIDSPREKER
Owner’s Manual
Mode d’emploi
Bedienungsanleitung
Manual del Usuario
Manuale di Istruzioni
Handleiding
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT. The wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW : EARTH
BLUE |
: NEUTRAL |
BROWN |
: LIVE |
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or colored GREEN or GREEN-and-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.
The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
The lightning flash with arrowhead symbol, within the equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock.
2
IMPORTANT SAFETY INSTRUCTIONS
INFORMATION RELATING TO PERSONAL INJURY, ELECTRICAL SHOCK, AND FIRE HAZARD POSSIBILITIES HAS BEEN INCLUDED IN THIS LIST.
WARNING- When using any electrical or electronic product, basic precautions should always be followed. These precautions include, but are not limited to, the following:
1. Read all Safety Instructions, Installation Instructions, Special Message Section items, and any Assembly Instructions found in this manual BEFORE making any connections, including connection to the main supply.
2. Do not attempt to service this product beyond that described in the user-maintenance instructions. All other servicing should be referred to qualified service personnel.
3. Main Power Supply Verification: Yamaha products are manufactured specifically for the supply voltage in the area where they are to be sold. If you should move, or if any doubt exists about the supply voltage in your area, please contact your dealer for supply voltage verification and (if applicable) instructions. The required supply voltage is printed on the name plate. For name plate location, please refer to the graphic found in the Special Message Section of this manual.
4. DANGER-Grounding Instructions: This product must be grounded and therefore has been equipped with a three pin attachment plug. If this product should malfunction, the ground pin provides a path of low resistance for electrical current, reducing the risk of electrical shock. If your wall socket will not accommodate this type plug, contact an electrician to have the outlet replaced in accordance with local electrical codes. Do NOT modify the plug or change the plug to a different type!
5. WARNING: Do not place this product or any other objects on the power cord or place it in a position where anyone could walk on, trip over, or roll anything over power or connecting cords of any kind. The use of an extension cord is not recommended! If you must use an extension cord, the minimum wire size for a 25' cord (or less) is 18 AWG. NOTE: The smaller the AWG number, the larger the current handling capacity. For longer extension cords, consult a local electrician.
6. Ventilation: Electronic products, unless specifically designed for enclosed installations, should be placed in locations that do not interfere with proper ventilation. If instructions for enclosed installations are not provided, it must be assumed that unobstructed ventilation is required.
7. Temperature considerations: Electronic products should be installed in locations that do not seriously contribute to their operating temperature. Placement of this product close to heat sources such as; radiators, heat registers etc., should be avoided.
8. This product was NOT designed for use in wet/damp locations and should not be used near water or exposed to rain. Examples of wet /damp locations are; near a swimming pool, spa, tub, sink, or wet basement.
9. This product should be used only with the components supplied or; a cart ,rack, or stand that is recommended by the manufacturer. If a cart, rack, or stand is used, please observe all safety markings and instructions that accompany the accessory product.
10. The power supply cord (plug) should be disconnected from the outlet when electronic products are to be left unused for extended periods of time. Cords should also be disconnected when there is a high probability of lightening and/or electrical storm activity.
11. Care should be taken that objects do not fall and liquids are not spilled into the enclosure through any openings that may exist.
12. Electrical/electronic products should be serviced by a qualified service person when:
a.The power supply cord has been damaged; or
b.Objects have fallen, been inserted, or liquids have been spilled into the enclosure through openings; or
c.The product has been exposed to rain; or
d.The product does not operate, exhibits a marked change in performance; or
e.The product has been dropped, or the enclosure of the product has been damaged.
13.This product, either alone or in combination with an amplifier and headphones or speaker/s, may be capable of producing sound levels that could cause permanent hearing loss. DO NOT operate for a long period of time at a high volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time period before damage occurs.
14. Some Yamaha products may have benches and/or accessory mounting fixtures that are either supplied as a part of the product or as optional accessories. Some of these items are designed to be dealer assembled or installed. Please make sure that benches are stable and any optional fixtures (where applicable) are well secured BEFORE using. Benches supplied by Yamaha are designed for seating only. No other uses are recommended.
PLEASE KEEP THIS MANUAL
92-469-3 |
3 |
Thank you for purchasing a Yamaha AS60-112T Powered Speaker.
Designed for use with theYamaha Silent String Instruments, the AS60-112T is equipped with a built-in 60-watt power amplifier which powers a 30cm speaker and dome tweeter. Thorough consideration was given to frequency range, characteristics and resonance when designing the AS60-112T to deliver maximum expression from string instruments like the Silent Violin, Viola, and Cello. When used in combination with the Yamaha AG-Stomp, you can make a creative sound system that delivers tremendous potential from the string instruments. The AS60-112T is also equipped with a LINE OUT jack, which allows you to connect multiple AS60-112Ts to create 120-watt or 180-watt high power systems.
To get the best results and longest life out of your AS60-112T, we recommend that you carefully read this manual, and keep it in a safe place for future reference.
Output Power |
|
Specifications |
|
60 Wrms |
|||
Speakers |
30 cm x 1, Dome Tweeter x 1 |
||
Controller/Switch |
VOLUME, TREBLE, MIDDLE, BASS, EQ ON/OFF, POWER |
||
Connection Jacks |
INPUT : Standard Phone Mono Jack |
||
|
LINE OUT : Standard Phone Mono Jack |
||
Input Level/Impedance |
INPUT : 0 dBm / 100 kΩ |
||
Output Level/Impedance |
LINE OUT : 0 dBm / 1 kΩ |
||
Power Requirements |
U.S. and Canadian models : 120 V, 60 Hz |
||
|
General model : 230 V, 50 Hz |
||
Power Consumption |
70 W |
||
Dimensions (W x H x D) |
513 x 491 x 291 mm (20.2” x 19.3” x 101.5”) |
||
Weight |
15.0 kg (33 lbs 1 oz) |
||
* Specifications and external appearance are subject to change without notice.
4
Precautions
●Avoid using your amplifier in the following locations to prevent possible damage:
•In direct sunlight or next to heating equipment.
•Extremely cold or hot locations.
•Locations exposed to high humidity or excessive dust.
•Locations subject to strong shocks or vibration.
●Before making any connections, make sure that the power on the amplifier and any external devices is switched OFF.
●To protect the speaker from possible damage, always set the VOLUME knob to “0” before switching the power ON/OFF.
●When connecting a speaker to this unit make sure to turn OFF the power first.
●Do not apply excessive force to the switches and controls.
●Your Yamaha powered speaker is a precision musical instrument. Handle it with care and avoid dropping or bumping it.
●Operating temperatures will rise during use. Make sure the amplifier is used in a well-ventilated area. The AS60-112T should be placed in a position were there is at least 30cm (12”) clearance from the wall on the sides, top and back of the amplifier.
●For safety, always remove the power plug from the AC wall outlet if there is any danger of lightning striking in your area.
●Keep the amplifier away from neon signs or fluorescent lighting to prevent noise pickup.
●To prevent damage and possibly electrical shock, never open the case and tamper with the internal circuitry.
●Never use benzene, thinner or other volatile liquids for cleaning, as these chemicals may cause damage or discoloration to the finish. Always use a dry, soft cloth to wipe off dust and dirt.
Nomenclature
■ Control Panel
q |
w |
e |
r |
q INPUT Jack (INPUT)
This is the AS60-112T’s INPUT jack.
Connect the instrument or the output from an external device to this jack.
When using the Silent Violin, Viola, or Cello, use a standard monaural plug cable to connect the LINE OUT jack on the instrument to this jack.
*Before making any connections, make sure that the power switch is set to OFF.
w Volume Control (VOLUME)
Controls the volume of the speaker.
e Equalizer Switch (EQ ON/OFF)
This is the ON/OFF switch for the equalizer circuit (TREBLE, MIDDLE, BASS). Set to ON (>), the equalizer circuit is active and the three knobs r can be used to adjust their respective frequencies. Set the switch to OFF (?) if you want to produce only the direct sound created by the instrument or external device, with no additional alteration.
t |
y |
r Equalizer Controls (TREBLE, MIDDLE, BASS)
Controls the level of their respective frequencies. TREBLE (high frequencies), MIDDLE (middle frequencies), BASS (low frequencies). When set to “0”, the tone will be flat, rotate the knob to the left (minus) to cut the frequency, and rotate to the right (plus) to boost the frequency.
t Expansion Output Jack (LINE OUT)
The signal received via the INPUT jack is transmitted from this jack although with its impedance converted (the signal also bypasses the equalizer circuit). When adding another powered speaker unit, such as another AS60-112T, connect the additional unit to this jack.
y Power Switch & Lamp (POWER)
This is the AS60-112T’s power switch. When the switch is depressed, the lamp next to the switch will light.
*To protect the speaker from damage, always make sure that the Volume Control w is set to “0” before the power is switched ON/OFF.
5
How to use the AS60-112T
Before making any connections, make sure that the power is
switched OFF on the AS60-112T and all other devices.
■ Connecting a Silent Violin/Viola/Cello
Use a standard monaural plug cable to connect the LINE OUT jack on the Yamaha Silent String Instrument (Silent Violin, Silent Viola, Silent
Cello) to the INPUT jack on the AS60-112T to create a 60W amplifier system.
* If the sound is distorted, adjust the volume on the instrument.
Silent Violin
INPUT
Silent Viola
Silent Cello
LINE OUT |
AS60-112T |
|
■ Connecting an AG-Stomp* (Monaural)
* sold separately
The Yamaha AG-Stomp is a guitar pre-amplifier system with built-in effects.
Use a standard monaural plug cable to connect the LINE OUT jack on the Yamaha Silent String Instrument to the INPUT jack on the AG-Stomp.
Next, use another standard monaural plug cable to connect the OUTPUT L/MONO jack on the AG-Stomp to the INPUT jack on the AS60-
112T. In this setup you can use the AG-Stomp to add effects such as Chorus, Reverb, etc. to the string instrument, or to prevent feedback during performance.
INPUT |
OUTPUT |
INPUT |
|
L/MONO |
|||
|
AG-Stomp
LINE OUT |
AS60-112T |
|
■ Connecting an AG-Stomp* (Stereo)
* sold separately
Since the AG-Stomp is equipped with stereo outputs, you can set up a stereo amplifier system by connecting one AS60-112T to the AG-Stomp’s
OUTPUT L/MONO jack, and another AS60-112T to the OUTPUT R jack.
This setup delivers greater expansiveness from effects like Stereo Chorus, etc.
All connections should be made using standard monaural plug cables.
LINE OUT
INPUT |
INPUT |
OUTPUT |
OUTPUT |
L/MONO |
R |
|
AG-Stomp |
AS60-112T |
AS60-112T |
L Side |
R Side |
■ Connecting Multiple AS60-112Ts
Connect the LINE OUT jack on one AS60-112T to the INPUT jack on another AS60-112T to create a high power 120W amplifier system. You can increase the amount of power by connecting a third or fourth unit to the system in the same manner.
INPUT
AS60-112T
LINE OUT
INPUT
AS60-112T
LINE OUT
6
HAUT-PARLEUR ALIMENTÉ
Nous vous remercions d’avoir choisi le haut-parleur alimenté Yamaha AS60-112T.
Conçu pour être utilisé avec les instruments à cordes de la série Silent Yamaha, le haut-parleur AS60-112T est équipé d'un amplificateur d'alimentation de 60 watts incorporé capable d'alimenter un haut-parleur de 30cm et un haut-parleur aigu en dôme. Une considération minutieuse a été réservée à la gamme de fréquences, aux caractéristiques et à la résonance lors de la conception du AS60-112T afin qu'il puisse délivrer une expression maximale des instruments à cordes tels que les instruments Silent Violin, Silent Viola, Silent Cello. Quand il est utilisé en combinaison avec le Yamaha AG-Stomp vous pouvez créer une sonorisation créative délivrant d'incroyables possibilités des instruments à cordes. Le haut-parleur AS60-112T est également équipé d'une prise de sortie LINE OUT qui vous permet de raccorder plusieurs AS60112T à votre système et créer ainsi des systèmes à grande puissance de 120 watts voire de 180 watts.
Pour avoir la certitude d’obtenir les meilleurs résultats possibles et d’assurer à votre AS60-112T une longévité optimale, nous vous recommandons de lire attentivement ce mode d’emploi et par ailleurs, de le conserver dans un endroit sûr à des fins de consultation ultérieure.
Puissance de sortie |
Fiche technique |
|
60 watts efficaces |
||
Haut-parleur |
30 cm: 1, Haut-parleur aigu en dôme: 1 |
|
Contrôleur / Commutateurs |
VOLUME, TREBLE, MIDDLE, BASS, EQ ON/OFF, POWER |
|
Prises de raccordement |
INPUT : prises de téléphone standard mono |
|
|
LINE OUT : prises de téléphone standard mono |
|
Niveau d’entrée / d’impédance |
INPUT : 0 dBm / 100 k-ohms |
|
Niveau de sortie / d’impédance |
LINE OUT : 0 dBm / 1 k-ohms |
|
Conditions d’alimentation |
Modèles pour les États-Unis et le Canada : 120 V, 60 Hz |
|
|
Modèle général : 230 V, 50 Hz |
|
Puissance consommée |
70 W |
|
Encombrement |
513 (largeur) x 491 (hauteur) x 291 (profondeur) mm |
|
Poids |
15,0 kg |
|
* Sous réserve de modification des renseignements techniques et de l’aspect extérieur sans préavis.
7
Loading...