XICOR X25043S, X25043PI-2,7, X25043PI, X25043P, X25043P-2,7 Datasheet

...
0 (0)
XICOR X25043S, X25043PI-2,7, X25043PI, X25043P, X25043P-2,7 Datasheet

APPLICATION NOTES

A V A I L A B L E

X25043/45AN11 • AN21

4K

X25043/45

512 x 8 Bit

Programmable Watchdog Supervisory E2PROM

FEATURES

Programmable Watchdog Timer

Low VCC Detection

Reset Signal Valid to VCC = 1V

1MHz Clock Rate

512 X 8 Bits Serial E2PROM —4 Byte Page Mode

Low Power CMOS

—50 μA Standby Current

—3mA Active Current

2.7V To 5.5V Power Supply

Block LockTM

—Protect 1/4, 1/2 or all of E 2PROM Array

Built-in Inadvertent Write Protection —Power-Up/Power-Down protection circuitry —Write Latch

—Write Protect Pin

High Reliability

—Endurance: 100,000 cycles per byte —Data Retention: 100 Years

—ESD protection: 2000V on all pins

Available Packages —8-Lead PDlP —8-Lead SOIC —14-Lead TSSOP

X25043 = Active LOW RESET

X25045 = Active HIGH RESET

DESCRIPTION

The X25043/45 combines three popular functions, Watchdog Timer, Voltage Supervision, and E2PROM in a single package. This combination lowers the system cost and reduces the board space requirements.

The Watchdog Timer provides an independent protec-

tion system for microcontrollers. During a system failure, the X25043/45 watchdog will respond with a RESET/

RESET signal after a selectable time-out interval. The user selects the interval from three preset values. Once selected, the interval does not change, even after cycling the power.

The system is protected from low voltage conditions by the X25043/45 low VCC detection circuits. When VCC drops below the minimum VCC trip point, the system is reset. Reset is asserted until VCC returns and stabilizes.

The memory portion of the X25043/45 is a CMOS 4096bit serial E2PROM, internally organized as 512 X 8. The X25043/45 features a Serial Peripheral Interface (SPI) and software protocol allowing operation on a simple three-wire bus.

The X25043/45 utilizes Xicor’s proprietary Direct Write™ cell, providing a minimum endurance of 100,000 cycles per byte and a minimum data retention of 100 years.

DIE PHOTOGRAPH

RESET

PROGRAMMABLE

VOLTAGE

CONTROL

SENSOR

LOGICIC

 

SERIALI

4K BITSI E2PROM

INTERFACEI

 

LOGICIC

 

HIGHI

VOLTAGE GENERATOR

 

AND

 

CONTROL

Direct Write™ is a trademark of Xicor, Inc.

 

©Xicor, Inc. 1994, 1995, 1996 Patents Pending

1

3844-6.5 5/9/96 T4/C2/D2 NS

W

 

A

T

T

I

C

I

M

H

E

D

R

O

 

G

 

3844 ILL F01

Characteristics subject to change without notice

X25043/45

PIN DESCRIPTIONS

Serial Output (SO)

SO is a push/pull serial data output pin. During a read cycle, data is shifted out on this pin. Data is clocked out by the falling edge of the serial clock.

Serial Input (SI)

SI is the serial data input pin. All opcodes, byte addresses, and data to be written to the memory are input on this pin. Data is latched by the rising edge of the serial clock.

Serial Clock (SCK)

The Serial Clock controls the serial bus timing for data input and output. Opcodes, addresses, or data present on the SI pin is latched on the rising edge of the clock input, while data on the SO pin changes after the falling edge of the clock input.

Chip Select (CS)

When CS is HIGH, the X25043/45 is deselected and the SO output pin is at high impedance and, unless an internal write operation is underway, the X25043/45 will be in the standby power mode. CS LOW enables the X25043/45, placing it in the active power mode. It should be noted that after power-up, a HIGH to LOW transition on CS is required prior to the start of any operation.

Write Protect (WP)

When WP is LOW, nonvolatile writes to the X25043/45 are disabled, but the part otherwise functions normally. When WP is held HIGH, all functions, including nonvolatile writes operate normally. WP going LOW while CS is still LOW will interrupt a write to the X25043/45. If the internal write cycle has already been initiated, WP going LOW will have no affect on a write.

Reset (RESET, RESET)

X25043/45, RESET/RESET is an active LOW/HIGH, open drain output which goes active whenever VCC falls below the mimimum VCC sense level. It will remain

active until VCC rises above the minimum VCC sense level for 200ms. RESET/RESET also goes active if

the Watchdog timer is enabled and CS remains either HIGH or LOW longer than the Watchdog time-out period. A falling edge of CS will reset the watchdog timer.

PIN CONFIGURATION

 

 

 

 

 

 

 

X25043/45

 

 

 

 

 

 

 

 

8-LEAD DIP/SOIC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

8

 

 

 

 

 

 

CS

 

 

 

 

VCC

 

 

 

SO

 

2

7

 

 

 

 

 

 

 

RESET/RESET

 

 

3

6

 

 

 

 

 

WP

 

 

 

SCK

VSS

 

4

5

 

SI

 

 

 

 

 

 

 

 

 

 

 

X25043/45

 

 

 

 

 

 

 

 

14-LEAD TSSOP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

14

 

 

 

 

CS

 

1

 

 

VCC

 

 

 

 

13

 

 

 

SO

 

2

 

 

RESET/RESET

 

 

 

NC

 

3

12

 

 

NC

 

 

 

NC

 

4

11

 

 

NC

 

 

 

NC

 

5

10

 

 

NC

 

 

 

 

 

9

 

 

 

 

WP

 

6

 

 

SCK

VSS

 

7

8

 

 

SI

 

 

 

 

 

 

 

 

 

 

3844 ILL F02.3

PIN NAMES

Symbol

Description

 

 

CS

Chip Select Input

SO

Serial Output

 

 

SI

Serial Input

 

 

SCK

Serial Clock Input

 

 

WP

Write Protect Input

 

 

VSS

Ground

VCC

Supply Voltage

RESET/RESET

Reset Output

3844 PGM T01.1

2

X25043/45

PRINCIPLES OF OPERATION

The X25043/45 is a 512 x 8 E2PROM designed to interface directly with the synchronous serial peripheral interface (SPI) of many popular microcontroller families.

The X25043/45 contains an 8-bit instruction register. It is accessed via the SI input, with data being clocked in on the rising SCK. CS must be LOW and WP input must be HIGH during the entire operation. The X25043/45 monitors the bus and provides a RESET/RESET output if there is no bus activity within the preset time period.

Table 1 contains a list of the instructions and their operation codes. All instructions, addresses and data are transferred MSB first. Bit 3 of the Read and Write instructions contain the higher order address bit, A8.

Data input is sampled on the first rising edge of SCK after CS goes LOW. SCK is static, allowing the user to stop the clock and then resume operations.

Write Enable Latch

The X25043/45 contains a “write enable” latch. This latch must be SET before a write operation will be completed internally. The WREN instruction will set the latch and the WRDI instruction will reset the latch. This latch is automatically reset upon a power-up condition and after the completion of a byte, page, or status register write cycle. The latch is also reset if WP is brought LOW.

Status Register

The RDSR instruction provides access to the status register. The status register may be read at any time, even during a write cycle. The status register is formatted as follows:

7

6

5

4

3

2

1

0

X

X

WD1

WD0

BL1

BL0

WEL

WIP

 

 

 

 

 

 

 

 

3844 PGM T02

When issuing, WREN, WRDI and RDSR commands, it is not necessary to send a byte address or data.

The Write-In-Process (WIP) bit indicates whether the X25043/45 is busy with a write operation. When set to a “1”, a write is in progress, when set to a “0”, no write is in progress. During a write, all other bits are set to “1”. The WIP bit is read-only.

The Write Enable Latch (WEL) bit indicates the status of the “write enable” latch. When set to a “1”, the latch is set, when set to a “0”, the latch is reset. The WEL bit is readonly and is set by the WREN instruction and reset by WRDI instruction or successful completion of a write cycle.

The Block Protect (BL0 and BL1) bits indicate the extent of protection employed. These nonvolatile bits are set by issuing the WRSR instruction and allows the user to select one of four levels of protection and program the watchdog timer. The X25043/45 is divided into four 1024-bit segments. One, two, or all four of the segments may be locked. That is, the user may read the segments but will be unable to alter (write) data within the selected segments. The partitioning is controlled as illustrated below with the state of BL1 and BL0.

Status Register Bits

Array Addresses

 

 

 

BL1

BL0

Protected

 

 

 

0

0

None

 

 

 

0

1

$180–$1FF

 

 

 

1

0

$100–$1FF

1

1

$000–$1FF

3844 PGM T04

The Watchdog Timer (WD0 and WD1) bits allow setting of the watchdog time-out function as shown in the table below. These nonvolatile bits are set by issuing the WRSR instruction.

Status Register Bits

Watchdog Time-out

 

 

 

WD1

WD0

(Typical)

 

 

 

0

0

1.4 Seconds

 

 

 

0

1

600 Milliseconds

 

 

 

1

0

200 Milliseconds

1

1

Disabled

 

 

 

3844 PGM T03

3

X25043/45

Clock and Data Timing

Data input on the SI line is latched on the rising edge of SCK. Data is output on the SO line by the falling edge of SCK.

Read Sequence

When reading from the E2PROM memory array, CS is first pulled LOW to select the device. The 8-bit READ instruction is transmitted to the X25043/45, followed by the 8-bit byte address. Bit 3 of the Read instruction contains address A8. This bit is used to select the upper or lower half of the device. After the read opcode and byte address are sent, the data stored in the memory at the selected address is shifted out on the SO line. The data stored in memory at the next address can be read sequentially by continuing to provide clock pulses. The byte address is automatically incremented to the next higher address after each byte of data is shifted out. When the highest address is reached ($1FF) the address counter rolls over to address $000, allowing the read cycle to be continued indefinitely. The read operation is terminated by taking CS HIGH. Refer to the read E2PROM Array operation sequence illustrated in Figure 1.

To read the status register the CS line is first pulled LOW to select the device followed by the 8-bit RDSR instruction. After the read status register opcode is sent, the contents of the status register is shifted out on the SO line as shown in Figure 2.

Write Sequence

Prior to any attempt to write data into the X25043/45 the “write enable” latch must first be set by issuing the WREN instruction (See Figure 3). CS is first taken LOW, then the WREN instruction is clocked into the X25043/45. After all eight bits of the instruction are

Table 1. Instruction Set

transmitted, CS must then be taken HIGH. If the user continues the write operation without taking CS HIGH after issuing the WREN instruction the write operation will be ignored.

To write data to the E2PROM memory array, the user issues the WRITE instruction, followed by the address and then the data to be written. Bit 3 of the Write instruction contains address A8. This bit is used to select the upper or lower half of the device. This is minimally a twenty-four clock operation. CS must go LOW and remain LOW for the duration of the operation. The host may continue to write up to four bytes of data to the X25043/45. The only restriction is the four bytes must reside on the same page. A page address begins with address X XXXX XX00 and ends with X XXXX XX11. If the byte address counter reaches X XXXX XX11 and the clock continues the counter will roll back to the first address of the page and overwrite any data that may have been written.

For the write operation (byte or page write) to be completed, CS can only be brought HIGH after the twenty-fourth, thirty-second, fortieth, or forty-eighth clock. If it is brought HIGH at any other time, the write operation will not be completed. Refer to Figure 4 and 5 below for a detailed illustration of the write sequences.

While the write is in progress, following a status register or E2PROM write sequence the status register may be read to check the WIP bit. During this time the WIP bit will be HIGH and all other bits in the status register will be undefined.

RESET/RESET Operation

The RESET (X25043) output is designed to go LOW whenever VCC has dropped below the minimum trip point and/or the Watchdog timer has reached its programmable time-out limit.

Instruction Name

Instruction Format*

Operation

 

 

 

 

WREN

0000

0110

Set the Write Enable Latch (Enable Write Operations)

 

 

 

 

WRDI

0000

0100

Reset the Write Enable Latch (Disable Write Operations)

RDSR

0000 0101

Read Status Register

 

 

 

WRSR

0000 0001

Write Status Register (Block Lock Bits)

 

 

 

 

READ

0000

A8011

Read Data from Memory Array beginning at selected

address

WRITE

0000

A8010

Write Data to Memory Array beginning at Selected Address

(1 to 4 Bytes)

 

 

 

 

3844 PGM T05.1

*Instructions are shown MSB in leftmost position. Instructions are transferred MSB first.

4

X25043/45

The RESET (X25045) output is designed to go HIGH whenever VCC has dropped below the minimum trip point and/or the watchdog timer has reached its programmable time-out limit.

Operational Notes

The X25043/45 powers-up in the following state:

The device is in the low power standby state.

A HIGH to LOW transition on CS is required to enter an active state and receive an instruction.

SO pin is high impedance.

The “write enable” latch is reset.

Figure 1. Read E2PROM Array Operation Sequence

Data Protection

The following circuitry has been included to prevent inadvertent writes:

The “write enable” latch is reset upon power-up.

A WREN instruction must be issued to set the “write enable” latch.

CS must come HIGH at the proper clock count in order to start a write cycle.

The “write enable” latch is reset when WP is brought LOW.

CS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

 

SCK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INSTRUCTION

 

 

 

 

 

BYTE ADDRESS

 

 

 

 

 

 

 

 

 

 

SI

 

 

 

8

 

 

 

7

6

5

4

3

2

1

0

 

 

 

 

 

 

 

 

 

 

 

 

9TH BIT OF ADDRESS

 

 

 

 

 

 

 

 

DATA OUT

 

 

 

HIGH IMPEDANCE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

6

5

4

3

2

1

0

SO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MSB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3844 FHD F04

Figure 2. Read Status Register Operation Sequence

CS

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

SCK

INSTRUCTION

SI

DATA OUT

HIGH IMPEDANCE

SO 7 6 5 4 3 2 1 0

MSB

3844 ILL F15

5

Loading...
+ 10 hidden pages