Woodstock W1798 User Manual

2.03 Mb
Loading...

MODEL W1798

2 PIECE

SPRAY GUN SET

OWNER'S MANUAL

Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz

COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT

THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.

#9637CR PRINTED IN CHINA

Model W1798 Professional Spray Gun

SAFETY

For Your Own Safety Read Instruction Manual

Before Operating This Equipment

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.

 

Indicates a potentially hazardous situation which, if

 

not avoided, COULD result in death or serious injury.

 

Indicates a potentially hazardous situation which, if

 

not avoided, MAY result in minor or moderate injury.

 

It may also be used to alert against unsafe practices.

NOTICE

This symbol is used to alert the user to useful

information about proper operation of the

 

equipment.

Safety Instructions for Pneumatic Tools

1.KEEP ALL SAFETY DEVICES IN PLACE and in working order.

2.REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before operation.

3.KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

4.DO NOT USE IN DANGEROUS ENVIRONMENT. Do not use pneumatic tools in damp or wet locations, or where any flammable or noxious fumes may exist. Keep work area well lighted.

5.KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept at a safe distance from work area.

6.MAKE WORKSHOP CHILD PROOF by locking your shop and shutting off air valves.

7.DO NOT FORCE TOOL. It will do the job better and safer at the rate for which it was designed.

8.USE THE RIGHT TOOL. Do not force tool or attachment to do a job for which it was not designed.

9.DO NOT USE UNDER THE INFLUENCE OF DRUGS OR ALCOHOL.

-1-

Model W1798 Professional Spray Gun

Safety Instructions for Pneumatic Tools

10.USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching.

11.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip

footwear is recommended. Wear a protective hair covering to contain long hair.

12.ALWAYS USE SAFETY GLASSES.

Also use a face or dust mask if cutting operation is dusty. Everyday eyeglasses only have

impact resistant lenses, they are NOT safety glasses.

13.WEAR APPROVED HEARING PROTECTION. Air escaping from pneumatic tools can exceed safe exposure limits and may cause hearing damage with prolonged exposure.

14.SECURE WORK. Use clamps or a vise to hold work when practical. It is safer than using your hand and frees both hands to operate tool.

15.MAINTAIN TOOLS WITH CARE.

Keep tools lubricated and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

16.REDUCE THE RISK OF UNINTENTIONAL FIRING. Do not carry tool with hand on trigger and always disconnect from air when not in use.

17.DISCONNECT TOOLS before servicing, changing accessories, or moving to another location.

18.DO NOT OVERREACH. Keep proper footing/balance at all times.

19.USE THE RECOMMENDED ACCESSORIES. Consult owner’s manual for recommended accessories. The use of improper accessories may cause risk of injury.

20.CHECK FOR DAMAGED PARTS BEFORE USING. Check for binding and alignment of parts, broken parts, part mounting, loose bolts, and any other conditions that mayaffect machine operation. Repair or replace damaged parts.

21.NEVER LEAVE UNATTENDED TOOL CONNECTED TO AIR.

Disconnect the air hose and do not leave tool until it is relieved of any built up pressure.

22.NEVER ALLOW UNTRAINED USERS TO USE THIS TOOL WHILE UNSUPERVISED.

23.IF YOU ARE UNSURE OF THE INTENDED OPERATION, STOP USING TOOL. Seek formal training or research books or magazines that specialize in pneumatic tools.

24.BE AWARE OF HOSE LOCATION WHEN USING PNEUMATIC TOOLS.

Hoses can easily become a tripping hazard when laid across the floor or spread out in a disorganized fashion.

-2-

Model W1798 Professional Spray Gun

Additional Safety Instructions for Spray Guns

1.READ THIS MANUAL. This manual contains proper operating instructions for this spray gun.

2.READ MATERIAL LABELS and MATERIAL SAFETY DATA SHEETS (MSDS). Read and know all the instructions on the packaging label and the MSDS before opening the package. This information could save your life.

3.ALWAYS WEAR A NIOSH APPROVED RESPIRATOR WHEN SPRAYING OR WORKING AROUND FINISHING MATERIALS.

4.FIRE EXTINGUISHERS. Always have a fully charged multi class or class B fire extinguisher in the immediate area.

5.FLAMMABLE MATERIAL. NEVER spray near open flame or where any spark could occur.

6.FRESH AIR. Always provide adequate exhaust to keep area free of built up vapors, NEVER spray in an enclosed space.

7.DISCONNECT COMPRESSED AIR.

Always disconnect the spray gun from compressed air before

cleaning, changing attachments or when performing maintenance of any kind on this tool.

8.PROTECTIVE CLOTHING. Protect exposed skin from overspray by wearing a protective suit or other approved garment.

9.INAPPROPRIATE USE. DO NOT point or shoot spray gun directly at yourself or another person or animals. Do not attempt to use the spray gun for any other use than it was intended.

10.STORAGE. Thoroughly clean and dry spray gun before storage. Store in an approved cabinet.

11.SOLVENTS. Always store solvents and shop towels soaked in solvent in approved containers.

12.EYE PROTECTION. Wear eye protection whenever spraying or cleaning. Solvents and chemicals can cause serious eye injury, which could lead to blindness.

13. OPERATING PRESSURE. DO NOT exceed the recommended inlet air pressure. Excessive pressure could cause the spray gun to burst or cause other internal equipment damage.

14.LOCAL LAWS. Consult local authorities regarding exhaust and waste disposal requirements.

No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other tools with caution and respect to avoid serious injury.

-3-

Model W1798 Professional Spray Gun

INTRODUCTION

Woodstock Technical

Large Sprayer

Support

Specifications

This tool has been specially designed to provide many years of trouble-free service. Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation.

Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to include the basic information for safety, setup, operation, maintenance, and service of this product.

We stand behind our tools! In the event that questions arise about your tool, please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail to:

tech-support@shopfox.biz. Our knowledgeable staff will help you troubleshoot problems and process warranty claims.

If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.

If you have comments about this manual, please contact us at:

Woodstock International, Inc. Attn: Technical Documentation Manager

P.O. Box 2309

Bellingham, WA 98227 Email: manuals@woodstockint.com

Type...........................

HP Siphon Feed

Fluid Tip...............................

1.8 mm

Air Consumption ................

6.0–8.8 CFM

Inlet Air Pressure ........

3–4 Bar/43–58 PSI

Material Capacity ............

1L / 33.8 fl oz

Maximum Pattern Width .......

180–230 mm

Small Sprayer

Specifications

Type...........................

HP Siphon Feed

Fluid Tip...............................

1.5 mm

Air Consumption ................

4.2–6.4 CFM

Inlet Air Pressure ........

3–4 Bar/43–58 PSI

Material Capacity .........

200ml / 6.8 fl oz

Pattern Width ....................

130–180mm

Read manual before operation. Become familiar with the spray gun safety and operation instructions before beginning any work. Serious personal injury may result if safety or operational information is not understood or followed.

-4-

Model W1798 Professional Spray Gun

SETUP

Unpacking

This tool has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately.

Inventory

The following is a description of the main components shipped with the Model W1798. Lay the components out to inventory them.

Note: If you can't find an item on this list, check the mounting location on the tool or examine the packaging materials carefully. Occasionally we pre-install certain components for safer shipping.

W1798 Inventory (Figure 1)

Qty

A.

Small Spray Gun ........................

1

B.

Storage Case.............................

1

C.

Large Spray Gun.........................

1

D.

14" NPT Quick Disconnect Fitting ....

2

E.

14" NPT Push-On Hose Fitting ........

1

A

B C

D

E

Figure 1. Model W1798 inventory.

-5-

Model W1798 Professional Spray Gun

Assembly

1.Attach the air hose to the spray gun with the included male 14" NPT quick connect fitting.

Note: You have the option of attaching a regulator/guage directly to the gun. Some may find this awkward and would rather mount the regulator/gauge closer to the air source.

2.Attach the spray gun to an air supply regulated between 43–58 PSI.

Note: For the best results, use a hose that will be dedicated for spray use only. Do not use a hose that has been used with an in-line oiler.

Controls

Refer to the list below and see Figures 2 and 3 to become familiar with the paint gun controls.

Atomizing Cap

Fluid Control

 

 

Pattern Control

Trigger

 

Reservoir Quick

 

Release Lock

 

 

Air Supply Port

 

Reservoir

Figure 2. Large paint gun controls.

1.Fluid Control: Controls the volume of paint that travels through the atomizing cap.

2.Pattern Control: Adjusts the spray pattern from a round pattern to a wide fan.

3.Atomizing Cap: Controls the spray pattern from vertical to horizontal.

4.Trigger: Two stage trigger. Stage one only releases compressed air for blowing off the work piece. Stage two sprays material.

5.Reservoir: Easy-clean spun aluminum canister, which holds a variety of thinned and non-thinned paints and lacquers.

6.Reservoir Quick Release Lock: Quick removal and installation of reservoir.

Trigger

 

Air Supply Port

Pattern Control

 

Fluid

 

Control

 

 

Atomizing

Reservoir Quick

Cap

Release Lock

 

Reservoir

 

-6-

Figure 3. Small paint gun controls.

 

Model W1798 Professional Spray Gun

OPERATIONS

EXPLOSION HAZARD! DO NOT smoke or have any source of flame or spark near spraying. Vapors will explode if ignited.

RESPIRATORY HAZARD! Always use respirator rated for organic vapor, paints, and solvents when using your spray equipment. Failure to protect your lungs can lead to respiratory illness and nervous system damage.

TOXIC FUMES! Always use an approved spray booth or well ventilated area when spraying. NEVER spray in a confined space where toxic fumes and flammable vapors can accumulate to deadly levels.

Spraying

The Model W1798 spray gun set is designed to spray low to medium viscosity liquids, like lacquers, stains, primers, multi-component paints, acrylics, epoxies etc. It is ideal for auto body touch-ups, woodworking projects, or projects with hard to reach areas.

To use your spray gun, do these steps:

1.Read and follow the material manufacturer's instructions for spraying, mixing, safety, disposal, and any other instruction on the label or Material Safety Data Sheet (MSDS).

2.Ensure the reservoir is securely tightened and all other fittings are secure to avoid air leaks or material spills.

3.Set the inlet air pressure (the air coming to the spray gun) to the lowest pressure recommended in Specifications on Page 4 or to the material manufacturer's

recommendations, then adjust higher as necessary.

4.Adjust the atomizing cap to vertical or horizontal. See Atomizing Cap and Fan Adjustments on Page 9 for further explanation.

5.Fill the reservoir with the material to be sprayed.

6. Trial and error are necessary to achieve the results you want along with a fair amount of practice. Test your material flow and spray pattern on a piece of cardboard or some scrap of material similar to your

-7- project.

Model W1798 Professional Spray Gun

7.Adjust the fluid control knob to start with a low volume of material and keep the atomization as low as possible. You will need to use a

combination of fluid control, inlet air pressure, air flow control and stroke speed to achieve the results you want. Spray so the material wets out nicely without running or sagging.

8.Use the pattern control knob to adjust the spray fan to your desired pattern.

9.Keep the gun tip perpendicular, parallel, and 6-8" from the work (as shown in Figure 4) when spraying. Do not allow your wrist to bend. This will cause the gun to arc across the surface and distribute the material unevenly, possibly creating sags and dry spots.

10.Begin spraying 2-3 inches before the workpiece and continue to the end of the workpiece. Continue the motion for a few inches past the work until you are ready for the return stroke.

11.Maintain an even speed when spraying.

12.Overlap each stroke by 50%. This will ensure even coverage, as shown in Figure 5. Overlapping less than 50%, as shown in the figure to the right, may lead to missed spots or streaky results.

 

 

Yes

No

 

 

 

 

 

Figure 5. Overlap technique.

 

 

13. The spray stroke should have an even

 

 

consistency and parallel edges. If it

 

 

doesn't, refer to Troubleshooting on

 

 

Page 12.

 

Figure 4.

Spray technique.

NOTICE

 

 

Tipping spray gun may cause material to spill out of the reservoir breather. Always hold the spray gun perpendicular to the ground to avoid potential spills and gravity feed problems.

-8-

Model W1798 Professional Spray Gun

Atomizing Cap and Fan

Adjustments

To help eliminate drips and sagging in the painted workpiece surface, the atomizing cap needs to be adjusted so

your paint gun stroke is perpendicular to the spray pattern. For example, Figure 6 shows the atomizing cap position for a horizontal spray pattern using a vertical stroke of the paint gun. You can adjust the atomizing cap to position the spray pattern at any orientation, but just make sure to keep the stroke of the paint gun perpendicular to the spray pattern for best results.

Pattern

Control

Tangs are Horizontal for

Horizontal Stroke

Often many spray pattern or spatter problems can be solved by making sure that the atomizing cap holes (Figure 8) are kept clean. However, when cleaning, do not use metal tools or you may increase the diameter of the preset holes. It is better to soak the cap in

paint thinner and use a wooden or plastic toothpick.

Holes

Figure 8. Atomizing cap holes.

Figure 6. Atomizing cap positioning for horizontal spray pattern and a vertical stroke.

To minimize overspray and save paint, you can adjust the pattern control knob so the pattern shape falls between a fan and a round spot pattern (see Figures 6 and 7).

Fan

Spot

Figure 7. Pattern adjustment.

-9-

Model W1798 Professional Spray Gun

CLEANING & LUBRICATION

Cleaning

EXPLOSION HAZARD! Chlorinated Solvents like Tricloroethane and Methylene Chloride (methyl chloride) can chemically react with aluminum and may explode. Many parts in spray guns are made of aluminum. Read solvent label carefully before using solvent.

NOTICE

DO NOT soak the spray gun body in solvent. Prolonged exposure to solvent will rapidly deteriorate the spray gun washers and seals. Ignoring this notice will void your warranty.

Proper cleaning is the best way to ensure trouble free performance from your spray gun. If your gun is not thoroughly cleaned, damage and poor spraying will result. Problems caused by improper cleaning will not be covered by the warranty. Clean the spray gun immediately after each use.

To clean your spray gun, do these steps:

1.Spray a small amount of solvent through the spray gun.

Note: Check with local laws regarding this practice. If you are spraying on a regular basis, spraying solvents into the air may be illegal. A cabinet style spray gun cleaner may be required.

3.Remove the reservoir and lid.

4.Disassemble the gun by unscrewing the fluid control knob, then remove the spring and needle (Figure 9).

Atomizing Cap

Fluid Control Knob

Fluid Tip

Body

 

Spring

 

Needle

Lid

Reservoir

 

Figure 9. Gun disassembled for cleaning.

Atomizing Cap

Fluid Control Knob

Fluid Tip

Body

Spring

Needle

 

Lid

 

 

Reservoir

 

Figure 10. Gun disassembled for cleaning.

5.Unscrew the atomizing cap with your fingers and the fluid tip with a wrench. The fully disassembled gun should look like Figure 9.

2. Disconnect the gun from the com-

pressed air!

Continued on next page

 

 

-10-

Model W1798 Professional Spray Gun

6.Rinse these parts thoroughly in solvent, then dry with compressed air or let air dry.

Note: If the small holes in the atomizing cap become blocked, soak in clean solvent. If the blockage still exists, clear the blockage with a small needle, taking great care to not enlarge or damage the hole. Damage to the hole will create a disrupted spray pattern.

7.Use an old tooth brush with solvent to clean the inner orifice and other hard to reach areas on the outside of the spray gun body.

8.Wipe the gun body with a lint free shop towel to dry.

Lubrication

Lubricate the following areas with spray gun lube after cleaning:

A.Atomizing Cap Threads and Gasket

B.Pattern Control Knob

C.Fluid Control Knob

D.Reservoir Quick Release Lever

E.Reservoir Gasket

F.Trigger Pin

After each cleaning, apply a thin film of petroleum jelly to the needle spring before reassembling.

B

A

C

F D

E

Figure 11. Lubrication points.

AB

C

F

E D

Figure 12. Lubrication points.

-11-

Model W1798 Professional Spray Gun

Troubleshooting

Symptom

Possible Cause

Possible Solution

Fluttering or

 

 

1. Dry or worn fluid tip seat

1.

Tighten fluid tip or replace

Spitting spray.

 

permits air to seep into fluid

 

seat with new one.

 

 

 

 

 

 

 

 

 

passage.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

Material level too low.

2.

Add material.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Fluid tip or strainer is

3.

Clean.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

blocked.

 

 

 

 

 

 

 

 

 

 

4.

Dry needle packing.

4.

Lubricate needle.

 

 

 

 

 

 

 

 

 

 

 

Uneven top or bot-

1. Atomizing cap holes are

1.

Clear holes.

tom pattern.

 

 

 

obstructed.

 

 

 

 

 

 

 

 

 

 

2.

Build-up on top or bottom of

2.

Clean.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

fluid tip.

 

 

 

 

 

 

 

 

 

 

3.

Build-up on atomizing cap is

3.

Clean.

 

 

 

 

 

 

 

 

 

on needle seat.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Right

or

 

arc

1. Left or right side horn holes

1.

Clear holes.

 

pattern.

 

 

 

are plugged.

 

 

 

 

 

 

 

 

 

 

2.

Build-up on left or right side

2.

Clean.

 

 

 

 

 

 

 

 

 

of fluid tip.

 

 

 

 

 

 

 

 

 

 

3.

Build-up of material inside

3. Clean.

 

 

 

 

 

 

 

 

 

atomizing cap.

 

 

 

 

 

 

 

 

 

 

 

 

 

Heavy deposit of

1. The material flow exceeds

1.

Lower fluid flow.

material in center.

 

the atomizing cap capacity.

 

 

 

 

 

 

 

 

 

 

2.

Inlet air pressure is too low.

2.

Increase inlet air pressure.

 

 

 

 

 

 

 

 

3.

Material is too thick.

3.

Thin material.

 

 

 

 

 

 

 

 

 

 

 

Narrow center pat-

1. Volume control turned in too

1.

Increase volume.

tern.

 

 

 

far.

 

 

 

 

 

 

 

 

 

 

2.

Inlet air pressure too high.

2.

Reduce inlet air pressure.

 

 

 

 

 

 

 

 

3.

Fluid pressure is too low.

3.

Increase fluid pressure.

 

 

 

 

 

 

 

 

4.

Material is too thin.

4.

Adjust material.

 

 

 

 

 

 

 

 

 

 

 

No spray output.

1. No pressure at gun.

1.

Check air supply.

 

 

 

 

 

 

 

 

2.

Fluid passages dirty.

2.

Clean gun, remove any

 

 

 

 

 

 

 

 

 

 

 

obstructions.

 

 

 

 

 

 

 

 

3.

Fluid control closed.

3.

Open.

 

 

 

 

 

 

 

 

4.

Out of paint.

4.

Refill.

 

 

 

 

 

 

 

 

 

 

 

 

-12-

Model W1798 Professional Spray Gun

Symptom

Possible Cause

Possible Solution

Excessive over-

1.

Fluid pressure too high.

1.

Reduce fluid pressure.

spray.

2.

Gun is too far from surface.

2.

Keep gun at recommended

 

 

 

 

distance.

 

3.

Spraying too fast.

3.

Slow down and maintain

 

 

 

 

consistent, even parallel

 

 

 

 

stroke.

 

 

 

 

 

Unable to control

1.

Pattern adjustment screw is

1.

Clean or replace.

spray fan.

 

not seating properly.

 

 

 

2.

Atomizing cap is loose.

2.

Tighten atomizing cap.

 

 

 

 

 

Runs and sags.

1.

Damaged seal.

1.

Replace damaged seals.

 

 

 

 

 

Material leaks from

1.

Cap not secure.

1.

Tighten.

cup.

2.

Cup not tight on gun body.

2.

Tighten.

 

3.

Leaking from cap vent hole.

3.

Hold gun upright do not

 

 

 

 

tilt.

 

 

 

 

 

Material leaks from

1.

Fluid tip loose.

1.

Tighten.

gun.

2.

Dry or damaged seals.

2.

Replace seals.

 

3.

Excessive pressure.

3.

Reduce pressure.

 

 

 

 

 

Thick dimpled fin-

1.

Holding gun too close to sur-

1.

Spray at recommended dis-

ish aka "Orange

 

face.

 

tance.

Peel."

2.

Inlet air pressure too low.

2.

Check inlet air pressure.

 

3.

Material not properly mixed.

3.

Follow manufacturer's

 

 

 

 

instructions.

 

4.

Surface is dirty or oily.

4.

More surface prep is

 

 

 

 

required.

 

 

 

 

 

Dry Spray.

1.

Inlet air pressure too high.

1.

Lower inlet air pressure.

 

2.

Gun too far from surface.

2.

Keep gun at recommended

 

 

 

 

distance.

 

3.

Gun stroke too fast.

3.

Slow down and maintain

 

 

 

 

consistent even parallel

 

 

 

 

stroke.

 

 

 

 

Gun leaks from

1.

Debris will not let the needle

1. Clean or replace both.

fluid tip.

 

seat with the fluid tip.

 

 

 

 

 

 

 

Contaminated

1.

Water or oil in the air line.

1.

Install an in-line air filter.

paint.

 

 

2.

Replace air line.

 

 

 

 

 

-13-

Model W1798 Professional Spray Gun

PARTS

REF PART # DESCRIPTION

1X1798001 PAINT INLET JOINT

2

X1798002

DIRECTIONAL SCREW

3

X1798003

SEALING RING

4

X1798004

NOZZLE ASSEMBLY

5

X1798005

FLUID NOZZLE

6

X1798006

PATTERN ADJUSTMENT VALVE

7

X1798007

TRIGGER PIN

8

X1798008

TRIGGER

9

X1798009

O-RING

10

X1798010

AIR VALVE SEAT

REF PART #

DESCRIPTION

11

X1798011

COMPRESSION SPRING

12

X1798012

O-RING

13

X1798013

AIR INLET PLUG

14

X1798014

FLUID ADJUSTMENT KNOB

15

X1798015

COMPRESSION SPRING

16

X1798016

FLUID NEEDLE ASSEMBLY

17

X1798017

RESERVOIR

18

X1798018

GUN BODY

19

X1798019

COVER ASSEMBLY

20

X1798020

REBUILD KIT

-14-

Model W1798 Professional Spray Gun

REF

PART #

DESCRIPTION

25

X1798025

AIR FITTING

26

X1798026

AIR FITTING

27

X1798027

TRIGGER

28

X1798028

TRIGGER NUT

29

X1798029

TRIGGER SCREW

30

X1798030

COMPRESSION SPRING

31

X1798031

GASKET

32

X1798032

VALVE

33

X1798033

BODY

34

X1798034

PACKING

35

X1798035

PLUG

36

X1798036

BODY

37

X1798037

COMPRESSION SPRING

38

X1798038

PLUNGER

39

X1798039

BARREL

40

X1798040

NEEDLE

41

X1798041

HOUSING

42

X1798042

GASKET

REF

PART #

DESCRIPTION

43

X1798043

COLLAR NUT

44

X1798044

PACKING

45

X1798045

LEATHER SEAL

46

X1798046

VALVE SCREW

47

X1798047

O-RING

48

X1798048

HOUSING

49

X1798049

C-CLIP

50

X1798050

STEM

51

X1798051

BARREL PLUNGER

52

X1798052

BODY

53

X1798053

VALVE

54

X1798054

HEAD

55

X1798055

NOZZLE ASSEMBLY

56

X1798056

ZINC RING

57

X1798057

BRASS RING

58

X1798058

AIR NOZZLE

59

X1798059

REBUILD KIT

-15-

WARRANTY AND RETURNS

Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or reimbursement of third party expenses incurred.

Woodstock International, Inc. will repair or replace, at its expense and at its option, the Shop Fox machine or machine part which in normal use has proven to be defective, provided that the original owner returns the product prepaid to a Shop Fox factory service center with proof of their purchase of the product within two years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged defect through inspection. If it is determined there is no defect, or that the defect resulted from causes not within the scope of Woodstock International Inc.'s warranty, then the original owner must bear the cost of storing and returning the product.

This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant that Shop Fox machinery complies with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under this warranty exceed the purchase price paid for the product, and any legal actions brought against Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special or consequential damages arising from the use of our products.

Every effort has been made to ensure that all Shop Fox machinery meets high quality and durability standards. We reserve the right to change specifications at any time because of our commitment to continuously improve the quality of our products.

CUT ALONG DOTTED LINE

Warranty Registration

Name___________________________________________________________________________________

Street __________________________________________________________________________________

City _________________________State___________________________Zip________________________

Phone #______________________Email __________________________Invoice #___________________

Model #_________Serial #______________Dealer Name__________________Purchase Date___________

The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of course, all information is strictly confidential.

1.How did you learn about us?

_____ Advertisement

____ Friend

____ Local Store

_____ Mail Order Catalog

____ Website

____ Other:

2.How long have you been a woodworker/metalworker?

_____ 0-2 Years

_____ 2-8 Years

____8-20 Years

_____ 20+ Years

3.How many of your machines or tools are Shop Fox?

 

_____ 0-2

_____ 3-5

____6-9

_____ 10+

4.

Do you think your machine represents a good value?

_____ Yes

____ No

5.

Would you recommend Shop Fox products to a friend?

_____ Yes

____ No

6.What is your age group?

_____ 20-29

____ 30-39

____ 40-49

_____ 50-59

____ 60-69

____ 70+

7.What is your annual household income?

_____ $20,000-$29,000

____ $30,000-$39,000

____ $40,000-$49,000

_____ $50,000-$59,000

____ $60,000-$69,000

____ $70,000+

8. Which of the following magazines do you subscribe to?

 

 

____

Cabinet Maker

____

Popular Mechanics

____

Today’s Homeowner

____

Family Handyman

____

Popular Science

____

Wood

____

Hand Loader

____

Popular Woodworking

____

Wooden Boat

____

Handy

____

Practical Homeowner

____

Woodshop News

____

Home Shop Machinist

____

Precision Shooter

____

Woodsmith

____

Journal of Light Cont.

____

Projects in Metal

____

Woodwork

____

Live Steam

____

RC Modeler

____

Woodworker West

____

Model Airplane News

____

Rifle

____

Woodworker’s Journal

____

Modeltec

____

Shop Notes

____

Other:

____

Old House Journal

____

Shotgun News

 

 

9. Comments:__________________________________________________________________

_____________________________________________________________________________

_____________________________________________________________________________

_____________________________________________________________________________

___________________________________________________________________

___________________________________________________________________

FOLD ALONG DOTTED LINE

Place

Stamp

Here

WOODSTOCK INTERNATIONAL INC.

P.O. BOX 2309

BELLINGHAM, WA 98227-2309

FOLD ALONG DOTTED LINE

TAPE ALONG EDGES--PLEASE DO NOT STAPLE