Woods Equipment BB48X, BB60X, BB84X, BB72X User Manual

4.3 (4)

BRUSHBULLTM

ROTARY CUTTER

BB48X

BB60X

BB72X

BB84X

Serial Number 1159929 and After

Includes Service and Parts Information for Serial Number 1159928 & Prior

MAN0632

(Rev. 4/20/2011)

OPERATOR'S MANUAL

TO THE DEALER:

Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner.

The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies that all Dealer Check List items have been completed. Please contact your dealer to complete this form. Dealers can register all Woods product at dealer.WoodsEquipment.com under Product Registration.

Failure to register the product does not diminish customer’s warranty rights.

TO THE OWNER:

Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals can be obtained from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

The equipment you have purchased has been carefully engineered and manufactured to provide dependable and satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified. Observe all safety information in this manual and safety decals on the equipment.

For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary tools and equipment to handle all your needs.

Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces provided:

Model: _______________________________

Date of Purchase: _____________________

Serial Number: (see Safety Decal section for location) ____________________________________

Provide this information to your dealer to obtain correct repair parts.

Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment. The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle with an exclamation mark) to indicate the degree of hazard for items of personal safety.

 

 

 

 

2 Introduction

Gen’l (Rev. 3/5/2010)

 

 

 

 

TABLE OF CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 SAFETY VIDEO ORDER FORM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9 SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 OWNER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 DEALER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 DEALER CHECK LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 ASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 INDEX TO PARTS LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . .57 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 PRODUCT WARRANTY . . . . . . . . . . . . . . . . . . . . . . . INSIDE BACK COVER REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . . . . . . . . BACK COVER

(Rev. 5/11/2010) MAN0632 (5/15/2007)

Introduction 3

SPECIFICATIONS

3-Point Hitch: BB48X, BB60X, BB72X

. . . . . . . . . .

. . . . . . . . .

. . . . . . . . . .

Category 1

BB84X . . . . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . .

. . . . . . . Category 1 & 2

Cutting Height . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . .

. . . . . . . . . .

. . . . 1" - 9"

Blade Spindle . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . .

. . . . . . . . . .

. . . . . . . . 1

Number of Blades . . . . . . . . . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . .

. . . . . . . . . . .

. . . . . . . 2

Blades . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . .

Heat Treated Alloy Steel

Blade Rotation . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . .

. . . . . . . . . . .

. . . . CCW

Tractor PTO RPM . . . . . . . . . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . .

. . . . . . . . . . .

. . . . . 540

Universal Drive . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . .

. . . . . . .Category 3 or 4

Side Frame Thickness . . . . . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . .

. . . . . . . 10 Ga or 11 Ga

Tailwheel . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . .

. . . . . . . . . . .

. . 4" x 16"

 

BB48X

BB60X

BB72X

BB84X

Cutting Width

48"

60"

72"

84"

Overall Width

53.5"

65.5"

77.5"

89.5"

Weight (Approximate)

456 lbs

554 lbs

702 lbs

1000 lbs

Blade Speed (Feet per minute)

13,000

14,335

14,963

14,963

Gearbox

1:1.92

1:1.69

1:1.47

1:1.26

Recommended Maximum Tractor HP

15 - 50

25 - 50

30 - 75

35 - 90

GENERAL INFORMATION

Some illustrations in this manual show the equipment with safety shields removed to provide a better view. This equipment should never be operated with any necessary safety shielding removed.

The purpose of this manual is to assist you in operating and maintaining your cutter. Read it carefully. It furnishes information and instructions that will help you achieve years of dependable performance. These instructions have been compiled from extensive field experience and engineering data. Some information may be general in nature due to unknown and varying

operating conditions. However, through experience and these instructions, you should be able to develop procedures suitable to your particular situation.

The illustrations and data used in this manual were current at the time of printing, but due to possible inline production changes, your machine may vary slightly in detail. We reserve the right to redesign and change the machines as may be necessary without notification.

Throughout this manual, references are made to right and left directions. These are determined by standing behind the equipment, facing the direction of forward travel. Blade rotation is counterclockwise as viewed from the top of the cutter.

4 Introduction

MAN0632 (5/15/2007)

 

 

Safety Video Order Form

BE SAFE!

BE ALERT!

BE ALIVE!

BE TRAINED

Before Operating Mowers!

Safety Training

Does Make a Difference.

ASSOCIATION OF

EQUIPMENT

MANUFACTURERS

Free Mower Safety Video

Fill out and return the order form and we will send you a FREE VHS or DVD video outlining Industrial and Agricultural Mower Safety Practices. The 22 minute video, developed in cooperation with AEM (Association of Equipment Manufacturers), reinforces the proper procedures to follow while operating your mowing equipment. The video does not replace the information contained in the Operator’s Manual, so please review this manual thoroughly before operating your new mowing equipment.

Safety Video Order Form (8/2/2005)

Safety 5

Also, available from the Association of Equipment Manufacturers:

A large variety of training materials (ideal for groups) are available for a nominal charge from AEM. Following is a partial list:

Training Package for Rotary Mowers/Cutters-English

Contains: DVD & VHS (English)

Guidebook for Rotary Mowers/Cutters (English)

AEM Industrial/Agricultural Mower Safety Manual (English) AEM Agricultural Tractor Safety Manual (English)

Training Package for Rotary Mowers/Cutters-English/Spanish

Contains: DVD & VHS (English/Spanish)

Guidebook for Rotary Mowers/Cutters (English/Spanish)

AEM Industrial/Agricultural Mower Safety Manual (English/Spanish) AEM Agricultural Tractor Safety Manual (English/Spanish)

AEM training packages are available through:

AEM at: www.aem.org or

Universal Lithographers, Inc. Email: aem@ulilitho.com 800-369-2310 tel 866-541-1668 fax

Free Mower/Cutter Safety Video Order Form

3 (Select one)

VHS Format - VHS01052 Safety Video

Please send me

DVD Format - DVD01052 Safety Video

Name: ________________________________________ Phone: __________________

Address: _____________________________________

_____________________________________

_____________________________________

Mower/Cutter Model: ______________________ Serial #: ________________________

Send to: ATTENTION: DEALER SERVICES

WOODS EQUIPMENT COMPANY

PO BOX 1000

OREGON IL 61061-1000

USA

6 Safety

Safety Video Order Form (Rev. 2/6/2006)

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act.

In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance, and storage of equipment.

It has been said, “The best safety device is an informed, careful operator.” We ask you to be that kind of operator.

TRAINING

Safety instructions are important! Read all attachment and power unit manuals; follow all safety rules and safety decal information. (Replacement manuals and safety decals are available from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319- 6637.) Failure to follow instructions or safety rules can result in serious injury or death.

If you do not understand any part of this manual and need assistance, see your dealer.

Know your controls and how to stop engine and attachment quickly in an emergency.

Operators must be instructed in and be capable of the safe operation of the equipment, its attachments, and all controls. Do not allow anyone to operate this equipment without proper instructions.

Never allow children or untrained persons to operate equipment.

PREPARATION

Check that all hardware is properly installed. Always tighten to torque chart specifications unless instructed otherwise in this manual.

Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

Make sure attachment is properly secured, adjusted, and in good operating condition.

Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

Before starting power unit, check all equipment driveline guards for damage. Replace any damaged guards. Make sure all guards rotate freely on all drivelines. If guards do not rotate freely on drivelines, repair and replace bearings before putting equipment into service.

Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.

Inspect chain, rubber, or steel band shielding before each use. Replace if damaged.

Remove accumulated debris from this equipment, power unit, and engine to avoid fire hazard.

Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.)

Make sure shields and guards are properly installed and in good condition. Replace if damaged.

A minimum 20% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, front tractor wheels could raise up resulting in loss of steering. The weight may be attained with front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment. Do not estimate.

Inspect and clear area of stones, branches, or other hard objects that might be thrown, causing injury or damage.

OPERATION

Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment.

(Safety Rules continued on next page)

Single Spindle Cutter LD/MD (Rev. 10/27/2006)

Safety 7

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

(Safety Rules continued from previous page)

Full chain, rubber, or steel band shielding must be installed when operating in populated areas or other areas where thrown objects could injure people or damage property.

If this machine is not equipped with full chain, rubber, or steel band shielding, operation must be stopped when anyone comes within 300 feet (92 m).

This shielding is designed to reduce the risk of thrown objects. The mower deck and protective devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. It is possible for objects to ricochet and escape, traveling as much as 300 feet (92 m).

Never direct discharge toward people, animals, or property.

Do not operate or transport equipment while under the influence of alcohol or drugs.

Operate only in daylight or good artificial light.

Keep hands, feet, hair, and clothing away from equipment while engine is running. Stay clear of all moving parts.

Always comply with all state and local lighting and marking requirements.

Never allow riders on power unit or attachment.

Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.

Always sit in power unit seat when operating controls or starting engine. Securely fasten seat belt, place transmission in neutral, engage brake, and ensure all other controls are disengaged before starting power unit engine.

Operate tractor PTO at 540 RPM. Do not exceed.

Do not operate PTO during transport.

Look down and to the rear and make sure area is clear before operating in reverse.

Do not operate or transport on steep slopes.

Do not stop, start, or change directions suddenly on slopes.

Use extreme care and reduce ground speed on slopes and rough terrain.

Watch for hidden hazards on the terrain during operation.

Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

Leak down or failure of mechanical or hydraulic system can cause equipment to drop.

Before performing any service or maintenance, disconnect driveline from tractor PTO.

MAINTENANCE

Before performing any service or maintenance, disconnect driveline from tractor PTO.

Before working underneath, disconnect driveline, raise cutter, and block cutter securely. Hydraulic system leak down and failure of mechanical or hydraulic system can cause equipment to drop.

Do not modify or alter or permit anyone else to modify or alter the equipment or any of its components in any way.

Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

Make sure attachment is properly secured, adjusted, and in good operating condition.

Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment.

Keep all persons away from operator control area while performing adjustments, service, or maintenance.

Make certain all movement of equipment components has stopped before approaching for service.

Frequently check blades. They should be sharp, free of nicks and cracks, and securely fastened.

Do not handle blades with bare hands. Careless or improper handling may result in serious injury.

Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous.

Tighten all bolts, nuts, and screws to torque chart specifications. Check that all cotter pins are

8 Safety

Single Spindle Cutter LD/MD (Rev. 10/27/2006)

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

installed securely to ensure equipment is in a safe condition before putting unit into service.

Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.)

Make sure shields and guards are properly installed and in good condition. Replace if damaged.

STORAGE

Keep children and bystanders away from storage area.

Disconnect cutter driveshaft and secure up off ground. Raise cutter with 3-point hitch. Place blocks under cutter side skids. Lower cutter onto blocks. Disconnect cutter from tractor 3-point hitch and carefully drive tractor away from cutter.

(Rev. 5/3/2007)

Single Spindle Cutter LD/MD (Rev. 10/27/2006)

Safety 9

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

MODEL NO.

SERIAL NO.

 

Woods Equipment Company

 

Oregon, Illinois, U.S.A.

1 - SERIAL NUMBER PLATE

8 - PN 1006682

DANGER

ROTATING BLADES AND

THROWN OBJECTS

Do not put hands or feet under or into mower when engine is running.

Before mowing, clear area of objects that may be thrown by blade.

Keep bystanders away.

Keep guards in place and in good condition.

BLADE CONTACT OR THROWN OBJECTS CAN CAUSE

SERIOUS INJURY OR DEATH.

6 – PN 20106

RED REAR REFLECTOR 4.5"

12 - PN 57123

RED REAR REFLECTOR 9"

DANGER

ROTATING DRIVELINE

CONTACT CAN CAUSE DEATH

KEEP AWAY!

DO NOT OPERATE WITHOUT -

All driveline guards, tractor and equipment shields in place

Drivelines securely attached at both ends

Driveline guards that turn freely on driveline

1006682-A

10 Safety

MAN0632 (5/15/2007)

 

 

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

WARNING

CRUSHING AND PINCHING HAZARD

Be extremely careful handling various parts of the machine. They are heavy and hands, fingers, feet, and other body parts could be crushed or pinched between tractor and implement.

Operate tractor controls from tractor seat only.

Do not stand between tractor and implement when tractor is in gear.

Make sure parking brake is engaged before going between tractor and implement.

Stand clear of machine while in operation or when it is being raised or lowered.

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

WARNING

TO AVOID SERIOUS INJURY OR DEATH:

Read Operator's Manual (available from dealer) and follow all safety precautions.

Keep all shields in place and in good condition.

Operate mower from tractor seat only.

Lower mower, stop engine and remove key before dismounting tractor.

Allow no children or untrained persons to operate equipment.

Do not transport towed or semi-mounted units over 20 mph.

FAILURE TO OPERATE SAFELY CAN

RESULT IN INJURY OR DEATH.

WARNING

FALLING OFF CAN RESULT IN BEING RUN OVER.

Tractor must be equipped with ROPS (or ROPS CAB) and seat belt. Keep foldable ROPS systems in "locked up" position at all times.

Buckle Up! Keep seat belt securely fastened.

Allow no riders.

RAISED EQUIPMENT CAN DROP AND CRUSH.

Before working underneath, follow all instructions and safety rules in operator's manual and securely block up all corners of equipment with jack stands.

Securely blocking prevents equipment from dropping from hydraulic leakdown, hydraulic system failures or mechanical component failures.

FALLING OFF OR FAILING TO BLOCK SECURELY CAN RESULT IN SERIOUS INJURY OR DEATH.

WARNING

DO NOT EXCEED PTO SPEED OF

540 RPM

PTO speeds higher than 540 RPM can cause equipment failure and personal injury.

1006681

2 - 1006681

 

 

 

 

DANGER

 

 

 

 

 

 

If shaft connection is visible, shield

7 - PN 1004114

is missing. Replace shield before

operating equipment.

1004114

 

 

 

 

 

 

10 - PN 33347

33347E

BE CAREFUL!

Use a clean, damp cloth to clean safety decals.

Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edges of decals causing them to peel or come off.

Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

MAN0632 (5/15/2007)

Safety 11

 

 

OPERATION

The operator is responsible for the safe operation of the cutter. The operator must be properly trained. Operators should be familiar with the cutter, the tractor, and all safety practices before starting operation. Read the safety rules and safety decals on page 7 through page 11.

This standard-duty cutter is designed for grass and weed mowing and shredding.

Recommended mowing speed for most conditions is from 2 to 5 mph.

Full chain, rubber, or steel band shielding must be installed when operating in populated areas or other areas where thrown objects could injure people or damage property.

If this machine is not equipped with full chain, rubber, or steel band shielding, operation must be stopped when anyone comes within 300 feet (92 m).

This shielding is designed to reduce the risk of thrown objects. The mower deck and protective devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. It is possible for objects to ricochet and escape, traveling as much as 300 feet (92 m).

Never allow riders on power unit or attachment.

Keep bystanders away from equipment.

Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

Operate tractor PTO at 540 RPM. Do not exceed.

CAUTION

Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

TRACTOR STABILITY

A minimum 20% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, front tractor wheels could raise up resulting in loss of steering. The weight may be attained with front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment. Do not estimate.

Figure 1. Tractor Stability

ATTACHING CUTTER TO TRACTOR - BB48X ONLY

Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

CAUTION

Make sure driveline will not bottom out at the shortest length and that it has at least 1/3 overlap at the longest length.

With cutter adjusted to transport position, set upper stop on tractor lift quadrant to prevent cutter from contacting the driveline when being raised.

Select a top link mounting pin (maximum length 3-5/8") that will allow floating link to swing freely through the cutter A-frame bars.

1.Attach tractor 3-point lift arms to the cutter hitch pins and secure.

2.Attach tractor top link to cutter clevis using forward hole. Select a top link mounting pin that will allow floating link to swing freely through the cutter A- frame bars.

NOTE: You will need to adjust the top link; refer to

Top Link Adjustment - BB48X Only (Figure 2), page 13.

12 Operation

(Rev. 4/24/2009) MAN0632 (5/15/2007)

3.Adjust the tractor lower 3-point arm anti-sway devices to prevent cutter from swinging side to side during transport.

4.Adjust tractor drawbar so that it will not interfere with cutter or driveline.

Top Link Adjustment - BB48X Only

(Figure 2)

1.Tractor top link

2.Cutter top link mounting pin

3.Floating link

4.Cutter hitch pin

5.A-Frame bars

6.Tractor top link bracket

Figure 2. Top Link Adjustment - BB48X Only

1.Attach tractor top link (1), to lowest hole provided in the tractor’s top link bracket (6).

2.Attach rear portion of tractor top link to the first hole on the cutter floating link (3). Select a top link mounting pin that will allow the floating link to swing freely through the cutter A-frame bars (5).

3.Raise cutter to transport position and adjust tractor top link until cutter is level in the raised position.

NOTE: If you cannot level the cutter using the lowest hole in the tractor’s top link bracket, move top link to the next hole and level the cutter.

Quick Hitch Attachment - BB48X Only

(Figure 3)

1.Remove brace arms (6), floating link (3), cap screw (11), spacer (7), and flange lock nut (9) from upper hole on A-frame bars (5) as shown on left in Figure 3.

NOTE: A-Frame bars are installed to mast plates with carriage bolts through the square holes.

2.Attach open end of floating link (3) to the bottom hole of A-frame bars (5). Secure using cap screw (11), sleeve (10), and flange lock nut (9) as shown on right in Figure 3.

3.Attach closed end of floating link (3) to diagonal braces (6). Secure using cap screw (8), spacer (7), and flange lock nut (9) supplied in hardware bag.

NOTE: Quick hitch top hook will pick up on sleeve (10). Lower quick hitch hook will attach to cutter hitch pins.

4.Raise cutter to transport position and adjust tractor top link until cutter is level in the raised position.

3.

Floating link

8.

1/2 NC x 4 Cap screw

 

5.

A-frame

9.

1/2 NC Flange lock nut

BB48X

6.

Diagonal braces

10.

1/2 x 3/4 x 2-13/16 Sleeve

7.

1/2 x 2-3/4 Spacer

11.

1/2 NC x 5 Cap screw

 

Figure 3. Standard Hitch and Quick Hitch Configurations - BB48X Only

(Rev. 4/24/2009) MAN0632 (5/15/2007)

Operation 13

Woods Equipment BB48X, BB60X, BB84X, BB72X User Manual

BB60X & BB72X

BB84X

Figure 4. Standard Hitch and Quick Hitch Configurations - BB60X, BB72X & BB84X

ATTACHING CUTTER TO TRACTOR - BB60X, BB72X, BB84X ONLY

Standard Hitch

1.Position tractor 3-point arms between the mast plates and secure with hitch pins and cotter pin. See left side of Figure 4. Note pin orientation for the BB84X.

2.Connect the tractor top link to the cutter A-frame using the upper holes and the appropriate hardware. The break link must be placed in the lower holes of the A-frame.

Quick Hitch

1.Position tractor 3-point arms between the mast plates and secure with hitch pins and cotter pin. See right side of Figure 4. Note pin orientation for the BB84X.

2.Attach tractor with the quick hitch to the cutter and secure according to the quick hitch manufacturer's instructions.

INSTALLATION AND REMOVAL

OF DRIVELINE (TRACTOR PTO)

To Install:

Pull locking collar back and at the same time push driveline onto tractor PTO shaft until locking device engages.

To Remove:

Hold driveline into position, pull locking collar back, and slide driveline off tractor PTO shaft.

Figure 5. Lock Collar

14 Operation

MAN0632 (5/15/2007)

 

 

DRIVELINE ATTACHMENT

Attach the cutter to the tractor 3-point hitch (or quick hitch if available). Do not attach driveline. Raise and lower cutter to determine maximum and minimum distance between the tractor PTO shaft and the gearbox input shaft. If the distance is too large, the driveline will be too short for proper engagement. If distance is too small, the driveline may bottom out in operation and damage the cutter or tractor.

The driveline length must be sufficient to provide at least 1/3 driveline length of engagement during operation. There must be at least 4 inches of engagement at the cutter’s lowest possible point of operation. The driveline must not bottom out when raised to the maximum height possible.

If driveline is too short, please call your Woods dealer for a longer driveline.

If driveline is too long, please follow the instructions for shortening the driveline.

SHORTENING DRIVELINE

1.Move cutter up and down to get the shortest possible distance between tractor PTO shaft and gearbox input shaft.

2.Separate driveline into two halves and connect them to the tractor PTO and gearbox.

3.Place driveline halves parallel to one another to determine how much to shorten the driveline.

DP2

Figure 6. Drive Halves Placed Parallel

4.Measure from end of the upper shield to the base of the bell on the lower shield (A). Add 1-9/16" to dimension (A). See Figure 7.

A

1-9/16"

DP3

Figure 7. Determine Shield Length

5. Cut the shield to the overall dimension.

DP4

Figure 8. Cut Shield

6.Place the cutoff portion of the shield against the end of the shaft and use as a guide. Mark and cut the shaft.

DP5

Figure 9. Cut Shaft to Length

7. Repeat step 6 for the other half of the drive.

MAN0632 (5/15/2007)

Operation 15

 

 

8. File and clean cut ends of both drive halves.

Do not use tractor if proper driveline engagement cannot be obtained through these methods.

Connect driveline to tractor PTO shaft, making sure the spring-activated locking collar slides freely and locks driveline to PTO shaft.

NOTICE

If attaching with quick hitch, the distance between the tractor PTO and gearbox input shaft will increase. Please follow the steps as you would for a 3-point hitch to insure proper engagement.

DRIVELINE INTERFERENCE CHECK

1.Check for clearance between driveline and cutter deck.

2.Slowly lift cutter and observe driveline. If clearance between driveline and cutter deck is less than 1 inch, shorten top link or limit upper travel of lower hitch arms. Refer to tractor operator's manual for instructions.

CUTTING HEIGHT ADJUSTMENT

Keep all persons away from operator control area while performing adjustments, service, or maintenance.

1.Level cutter from side to side. Check by measuring from cutter frame to the ground at each deck rail.

2.Adjust, using tractor 3-point arm leveling device.

NOTE: Keep the front of cutter slightly lower than rear for best mowing.

3.Control cutting height with tractor 3-point arms, rear tailwheel adjustment, or optional check chains.

4.To raise rear of cutter, move tailwheel arm down.

5.To raise front of cutter, raise tractor 3-point arms or shorten optional check chains.

The cutting height is the distance between the blade and the ground. The blades are approximately 8.5" below the deck. To check cutting height, do the following:

a)Place a straight edge along top edge of deck.

b)Select a cutting height; as an example, for an approximate cutting height of 3", set the center of the deck 11.5" above the ground:

3" Desired cutting height

+8.5" Distance blade cutting edge is below deck

=11.5"

c)Adjust the front-to-rear attitude from 1/2" to 3/4" higher than the front.

6.Adjust top link (BB60X, BB72X, BB84X) to provide 2" of clearance between break link (2) and rear lift links. See Figure 10. The clearance will allow cutter to float over uneven terrain.

Avoid low cutting heights. Striking the ground with blades produces one of the most damaging

SHREDDING MATERIAL

shock loads a cutter can encounter. Allowing blades to contact ground repeatedly will cause damage to cutter and drive.

For shredding, set the cutter lower at rear. Determine how much lower to set the rear by experimenting in different situations.

1. Deck

2. Break link

3. Tractor top link

H = Cutting height

Figure 10. Cutting Height Adjustment

16 Operation

MAN0632 (5/15/2007)

 

 

CHECK CHAIN ADJUSTMENT

1.Refer to Install Optional Check Chains, page 42 for check chain installation.

2.After making cutting height adjustment, adjust both chains (3) in check chain bracket (2) so you have the same number of links on each side. This will keep cutting level.

2.Check chain bracket

3.Check chain

Figure 11. Check Chain Adjustment

OPERATING TECHNIQUE

1.Power for operating the cutter is supplied by the tractor PTO. Operate PTO at 540 rpm. Know how to stop the tractor and cutter quickly in an emergency.

2.Engage PTO at a low engine rpm to minimize stress on the drive system and gearbox. With PTO engaged, raise PTO speed to 540 rpm and maintain throughout cutting operation.

Gearbox protection is provided by a slip clutch with replacement fiber disc or a shear bolt. The slip clutch is designed to slip and the shear bolt will shear when excessive torsion loads occur.

3.Move slowly into material. Adjust tractor ground speed to provide a clean cut without lugging the tractor engine. Use a slow ground speed for better shredding.

Proper ground speed will depend on the terrain and the material’s height, type, and density.

Normally, ground speed will range from 2 to 5 mph. Tall, dense material should be cut at a low speed; thin, medium-height material can be cut at a faster ground speed.

4.Always operate tractor PTO at 540 rpm to maintain proper blade speed and to produce a clean cut.

5.Under certain conditions tractor tires may roll down some grass and prevent cutting at the same height as the surrounding area. When this occurs, reduce your ground speed but maintain PTO at 540 rpm. The lower ground speed will permit grass to rebound partially.

STORAGE

Disconnect cutter driveshaft and secure up off ground. Raise cutter with 3-point hitch. Place blocks under cutter side skids. Lower cutter onto blocks. Disconnect cutter from tractor 3-point hitch and carefully drive tractor away from cutter.

Keep children and bystanders away from storage area.

PRE-OPERATION CHECK LIST

OWNER’S RESPONSIBILITY

___ Review and follow all safety rules and safety decal instructions on page 7 through page 11.

___ Check that equipment is properly and securely attached to tractor.

___ Make sure driveline spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

___ Set tractor PTO at 540 rpm.

___ Lubricate all grease fitting locations. Make sure PTO shaft slip joint is lubricated.

___ Check to be sure gear lube runs out the small check plug on side of gearbox.

___ Check that all hardware is properly installed and secured.

___ Check that blades are sharp and secure and cutting edge is positioned to lead in a counterclockwise rotation.

___ Check that shields and guards are properly installed and in good condition. Replace if damaged.

___ Check cutting height, front-to-rear attitude, and top link adjustment.

___ Place tractor PTO and transmission in neutral before starting engine.

___ Inspect area to be cut and remove stones, branches, or other hard objects that might be thrown and cause injury or damage.

MAN0632 (5/15/2007)

Operation 17

 

 

OWNER SERVICE

The information in this section is written for operators who possess basic mechanical skills. If you need help, your dealer has trained service technicians available. For your protection, read and follow the safety information in this manual

Keep all persons away from operator control area while performing adjustments, service, or maintenance.

CAUTION

If you do not understand any part of this manual and need assistance, see your dealer.

Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

BLOCKING METHOD

Before performing any service or maintenance, disconnect driveline from tractor PTO.

Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body underneath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death. Follow Operator's Manual instructions for working underneath and blocking requirements or have work done by a qualified dealer.

To minimize the potential hazards of working underneath the cutter, follow these procedures.

1.Jackstands with a load rating of 1000 lbs or more are the only approved blocking device for this cutter. Install a minimum of four jackstands (shown by Xs in Figure 12) under the cutter before working underneath unit.

Do not position jackstands under wheels, axles, or wheel supports. Components can rotate and cause cutter to fall.

2.Consider the overall stability of the blocked unit. Just placing jackstands underneath will not ensure your safety.

The working surface must be level and solid to support the weight on the jackstands. Make sure jackstands are stable, both top and bottom. Make sure cutter is approximately level.

3.With full cutter weight lowered onto jackstands, test blocking stability before working underneath.

4.If cutter is attached to tractor when blocking, set the brakes, remove key, and block cutter before working underneath.

5.Securely block rear tractor wheels, in front and behind. Tighten tractor lower 3-point arm anti-sway mechanism to prevent side-to-side movement.

LUBRICATION INFORMATION

1.Do not let excess grease collect on or around parts, particularly when operating in sandy areas.

2.See Figure 12 for lubrication points and frequency of lubrication based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication.

3.Use a lithium grease of #2 consistency with a MOLY (molybdenum disulfide) additive for all locations unless otherwise noted. Be sure to clean fittings thoroughly before attaching grease gun. One good pump of most guns is sufficient when the lubrication schedule is followed.

Gearbox Lubrication

1.For gearbox, use a high quality gear oil with a viscosity index of 80W or 90W and an API service rating of GL-4 or -5 in gearboxes.

2.Fill gearbox until oil runs out the side plug on gearbox. Check gearbox daily for evidence of leakage, and contact your dealer if leakage occurs.

Driveline Lubrication

1.Lubricate the driveline slip joint every eight operating hours. Failure to maintain proper lubrication could result in damage to U-joints, gearbox, and driveline.

2.Lower cutter to ground, disconnect driveline from tractor PTO shaft, and slide halves apart but do not disconnect from each other.

3.Apply a bead of grease completely around male half where it meets female half. Slide drive halves over each other several times to distribute grease.

18 Owner Service

MAN0632 (5/15/2007)

 

 

Loading...
+ 42 hidden pages