Woods Equipment BW180XHDQ, BW180XHD, BW126XHD, BW126XHDQ User Manual

0 (0)

BATWING®

ROTARY CUTTER

BW180XHD

BW180XHDQ

BW126XHD

BW126XHDQ

MAN0963 (Rev. 2/16/2012)

OPERATOR'S MANUAL

TO THE DEALER:

Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner.

The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies that all Dealer Check List items have been completed. Dealers can register all Woods product at dealer.WoodsEquipment.com under Product Registration.

Failure to register the product does not diminish customer’s warranty rights.

TO THE OWNER:

Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals can be obtained from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

The equipment you have purchased has been carefully engineered and manufactured to provide dependable and satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified. Observe all safety information in this manual and safety decals on the equipment.

For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary tools and equipment to handle all your needs.

Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces provided:

Model: _______________________________

Date of Purchase: _____________________

Serial Number: (see Safety Decal section for location) ____________________________________

Provide this information to your dealer to obtain correct repair parts.

Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment. The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle with an exclamation mark) to indicate the degree of hazard for items of personal safety.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 Introduction

Gen’l (Rev. 12/5/2011)

 

 

 

 

 

 

TABLE OF CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY VIDEO ORDER FORM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 OWNER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 DEALER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 ASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 DEALER CHECK LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 INDEX TO PARTS LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 83 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 PRODUCT WARRANTY . . . . . . . . . . . . . . . . . . . . . . . INSIDE BACK COVER REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . . . . . . . .BACK COVER

!LEA EL INSTRUCTIVO!

Si no lee Ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad.

This Operator’s Manual should be regarded as part of the machine. Suppliers of both new and second-hand machines must make sure that this manual is provided with the machine.

MAN0963 (2/16/2012)

Introduction 3

 

 

SPECIFICATIONS

 

 

BW180XHD / BW180XHDQ

BW126XHD / BW126XHDQ

Cutting Height (Varies with tire selection) . . .

. . . . . . . . . . . . . . . . 1" - 15"

1" - 15"

Cutting Width . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . . .180" (15’)

126" (10.5’)

Overall Width . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . .190"

140"

Transport Width . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . .96"

93"

Tractor HP . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . .65-250

65-250

Blade Spindle . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . 3

2

Blade Overlap . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . .6"

6"

Number of Blades . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . 6

4

Blade Rotation . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . .Left Spindle: CW; Right & Center Spindles: CCW

Main Driveline . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . Cat 5 Heavy

Cat 5 Heavy

CV . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . Cat 6

Cat 6

Side Frame Thickness . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . 1/4"

1/4"

Weight (approximate lbs.) .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . 4200

4000

Wheel Size. . . . . . . . . . . . .

15" Rims (BW180XHD and BW180XHDQ only) or 21" OD Solid Tires, Airplane

Torsion Protection . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . . Slip Clutch

Slip Clutch

 

BW180XHD

BW180XHDQ

 

BW126XHD

BW126XHDQ

Tractor PTO rpm

540

1000

Blade Speed (Feet per minute)

15,700

16,000

 

 

 

GENERAL INFORMATION

Some illustrations in this manual show the equipment with safety shields removed to provide a better view. This equipment should never be operated with any necessary safety shielding removed.

The purpose of this manual is to assist you in operating and maintaining your cutter. Read it carefully. It furnishes information and instructions that will help you achieve years of dependable performance. These instructions have been compiled from extensive field experience and engineering data. Some information may be general in nature due to unknown and varying

operating conditions. However, through experience and these instructions, you should be able to develop procedures suitable to your particular situation.

The illustrations and data used in this manual were current at the time of printing but, due to possible inline production changes, your machine may vary slightly in detail. We reserve the right to redesign and change the machines as may be necessary without notification.

Throughout this manual, references are made to right and left directions. These are determined by standing behind the equipment facing the direction of forward travel. Blade rotation is clockwise (left wing) and counterclockwise (right wing and center section) as viewed from the top of the cutter.

4 Introduction

MAN0963 (2/16/2012)

 

Safety Video Order Form

BE SAFE!

BE ALERT!

BE ALIVE!

BE TRAINED

Before Operating Mowers!

Safety Training

Does Make a Difference.

ASSOCIATION OF

EQUIPMENT

MANUFACTURERS

Free Mower Safety Video

Fill out and return the order form and we will send you a FREE VHS or DVD video outlining Industrial and Agricultural Mower Safety Practices. The 22 minute video, developed in cooperation with AEM (Association of Equipment Manufacturers), reinforces the proper procedures to follow while operating your mowing equipment. The video does not replace the information contained in the Operator’s Manual, so please review this manual thoroughly before operating your new mowing equipment.

Safety Video Order Form (8/2/2005)

Safety 5

Also, available from the Association of Equipment Manufacturers:

A large variety of training materials (ideal for groups) are available for a nominal charge from AEM. Following is a partial list:

Training Package for Rotary Mowers/Cutters-English

Contains: DVD & VHS (English)

Guidebook for Rotary Mowers/Cutters (English)

AEM Industrial/Agricultural Mower Safety Manual (English) AEM Agricultural Tractor Safety Manual (English)

Training Package for Rotary Mowers/Cutters-English/Spanish

Contains: DVD & VHS (English/Spanish)

Guidebook for Rotary Mowers/Cutters (English/Spanish)

AEM Industrial/Agricultural Mower Safety Manual (English/Spanish) AEM Agricultural Tractor Safety Manual (English/Spanish)

AEM training packages are available through:

AEM at: www.aem.org or

Universal Lithographers, Inc. Email: aem@ulilitho.com 800-369-2310 tel 866-541-1668 fax

Free Mower/Cutter Safety Video Order Form

3 (Select one)

VHS Format - VHS01052 Safety Video

Please send me

DVD Format - DVD01052 Safety Video

Name: ________________________________________ Phone: __________________

Address: _____________________________________

_____________________________________

_____________________________________

Mower/Cutter Model: ______________________ Serial #: ________________________

Send to: ATTENTION: DEALER SERVICES

WOODS EQUIPMENT COMPANY

PO BOX 1000

OREGON IL 61061-1000

USA

6 Safety

Safety Video Order Form (Rev. 2/6/2006)

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act.

In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance, and storage of equipment.

It has been said, “The best safety device is an informed, careful operator.” We ask you to be that kind of operator.

INSTALLATION

Hydraulics must be connected as instructed in this manual. Do not substitute parts, modify, or connect in any other way.

TRAINING

Safety instructions are important! Read all attachment and power unit manuals; follow all safety rules and safety decal information. (Replacement manuals and safety decals are available from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319- 6637.) Failure to follow instructions or safety rules can result in serious injury or death.

If you do not understand any part of this manual and need assistance, see your dealer.

Know your controls and how to stop engine and attachment quickly in an emergency.

Operators must be instructed in and be capable of the safe operation of the equipment, its attachments, and all controls. Do not allow anyone to operate this equipment without proper instructions.

Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or other body parts to check for leaks. Wear safety goggles. Hydraulic fluid under pressure can easily penetrate skin and will cause serious injury or death.

Make sure that all operating and service personnel know that if hydraulic fluid penetrates skin, it must be surgically removed as soon as possible by a doctor familiar with this form of injury or gangrene, serious injury, or death will result. CON-

TACT A PHYSICIAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES. DO NOT DELAY.

Never allow children or untrained persons to operate equipment.

PREPARATION

Check that all hardware is properly installed. Always tighten to torque chart specifications unless instructed otherwise in this manual.

Air in hydraulic systems can cause erratic operation and allows loads or equipment components to drop unexpectedly. When connecting equipment or hoses or performing any hydraulic maintenance, purge any air in hydraulic system by operating all hydraulic functions several times. Do this before putting into service or allowing anyone to approach the equipment.

Make sure all hydraulic hoses, fittings, and valves are in good condition and not leaking before starting power unit or using equipment. Check and route hoses carefully to prevent damage. Hoses must not be twisted, bent sharply, kinked, frayed, pinched, or come into contact with any moving parts. Operate moveable components through full operational range to check clearances. Replace any damaged hoses immediately.

After connecting hoses, check that all control lever positions function as instructed in the Operator's Manual. Do not put into service until control lever and equipment movements are correct.

Set tractor hydraulic relief valve at 2500 psi (170 bars) (17,000 kPa) to prevent injury and equipment damage due to hydraulic system failure.

Your dealer can supply original equipment hydraulic accessories and repair parts. Substitute parts may not meet original equipment specifications and may be dangerous.

Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

Make sure attachment is properly secured, adjusted, and in good operating condition.

Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

(Safety Rules continued on next page)

BW180_ SR (Rev. 12/10/2007)

Safety 7

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

(Safety Rules continued from previous page)

Make sure driveline guard tether chains are attached to the tractor and equipment as shown in the pamphlet that accompanies the driveline. Replace if damaged or broken. Check that driveline guards rotate freely on driveline before putting equipment into service.

Before starting power unit, check all equipment driveline guards for damage. Replace any damaged guards. Make sure all guards rotate freely on all drivelines. If guards do not rotate freely on drivelines, repair and replace bearings before putting equipment into service.

Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.

Remove accumulated debris from this equipment, power unit, and engine to avoid fire hazard.

Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.)

Make sure shields and guards are properly installed and in good condition. Replace if damaged.

Always attach safety chain to tractor drawbar when transporting unit.

Always comply with all state and local lighting and marking requirements.

Never allow riders on power unit or attachment.

Do not operate PTO during transport.

Do not operate or transport on steep slopes.

Do not operate or transport equipment while under the influence of alcohol or drugs.

The maximum transport speed for towed and semi-mounted machines is 20 mph (32 km/h). Regardless of the maximum speed capability of the towing tractor, do not exceed the implement’s maximum transport speed. Doing so could result in:

Loss of control of the implement and tractor

Reduced or no ability to stop during braking

Implement tire failure

Damage to the implement or its components.

Use additional caution and reduce speed when under adverse surface conditions, turning, or on inclines.

Never tow this implement with a motor vehicle.

Do not put this equipment into service unless all side skids are properly installed and in good condition. Replace if damaged.

A minimum 20% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, tractor could tip over, causing personal injury or death. The weight may be attained with a loader, front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment. Do not estimate.

Inspect and clear area of stones, branches, or other hard objects that might be thrown, causing injury or damage.

TRANSPORTATION

Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.

Always raise unit and install transport locks before transporting. Leak down or failure of mechanical or hydraulic system can cause equipment to drop.

OPERATION

Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment.

Never walk, stand, or place yourself or others under a raised wing or in the path of a lowering wing. Hydraulic system leak-down, hydraulic system failures, mechanical failures, or movement of control levers can cause wings to drop unexpectedly and cause severe injury or death.

Full chain or rubber shielding must be installed when operating in populated areas or other areas where thrown objects could injure people or damage property.

If this machine is not equipped with full chain or rubber shielding, operation must be stopped when anyone comes within 300 feet (92 m).

This shielding is designed to reduce the risk of thrown objects. The mower deck and protective devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. It is possible for objects to ricochet and escape, traveling as much as 300 feet (92 m).

Never direct discharge toward people, animals, or property.

8 Safety

BW180_SR (Rev. 12/10/2007)

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Do not operate or transport equipment while under the influence of alcohol or drugs.

Operate only in daylight or good artificial light.

Keep hands, feet, hair, and clothing away from equipment while engine is running. Stay clear of all moving parts.

Always comply with all state and local lighting and marking requirements.

Never allow riders on power unit or attachment.

Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.

Always sit in power unit seat when operating controls or starting engine. Securely fasten seat belt, place transmission in neutral, engage brake, and ensure all other controls are disengaged before starting power unit engine.

Operate tractor PTO at 540 RPM (1000 RPM on Q Series cutters). Do not exceed.

Raise or lower wings slowly to prevent personal injury or damage to cutter.

Connect PTO driveline directly to power unit PTO shaft. Never use adapter sleeves or adapter shafts. Adapters can cause driveline failures due to incorrect spline or incorrect operating length and can result in personal injury or death.

Look down and to the rear and make sure area is clear before operating in reverse.

Do not operate or transport on steep slopes.

Do not stop, start, or change directions suddenly on slopes.

Watch for hidden hazards on the terrain during operation.

Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

Continuous operation while the clutch is slipping could cause heat build-up resulting in fire. Adjust slip clutch pressure by tightening springs to the dimension shown in the “Owner Service” section. If clutch is set to minimum spring length, replace the friction disks as shown.

On pull-type or semi-mounted units with optional hydraulic cutting height adjustment, use a single-acting cylinder with a maximum extended

length of 28-1/4" (718 mm) from attaching point center to center.

MAINTENANCE

Before servicing, adjusting, repairing or unplugging, stop tractor engine, place all controls in neutral, set park brake, remove ignition key, and wait for all moving parts to stop.

Before dismounting power unit or performing any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pressure, set parking brake, stop engine, remove key, and unfasten seat belt.

Before working underneath, disconnect driveline from tractor, lower wings to ground, raise cutter, and pin transport bar in raised position. Attach parking jack and lower to ground. Securely block all four corners of center section and each wing with jackstands. Blocking up prevents the cutter from dropping due to hydraulic leak down, hydraulic system failure, or mechanical component failure.

Do not modify or alter or permit anyone else to modify or alter the equipment or any of its components in any way.

Your dealer can supply original equipment hydraulic accessories and repair parts. Substitute parts may not meet original equipment specifications and may be dangerous.

To prevent contamination during maintenance and storage, clean and then cover hose ends, fittings, and hydraulic ports with tape.

Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment.

Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body underneath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death. Follow Operator's Manual instructions for working underneath and blocking requirements or have work done by a qualified dealer.

(Safety Rules continued on next page)

BW180_ SR (Rev. 12/10/2007)

Safety 9

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

(Safety Rules continued from previous page)

Keep all persons away from operator control area while performing adjustments, service, or maintenance.

Make certain all movement of equipment components has stopped before approaching for service.

Frequently check blades. They should be sharp, free of nicks and cracks, and securely fastened.

Do not handle blades with bare hands. Careless or improper handling may result in serious injury.

Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous.

Tighten all bolts, nuts, and screws to torque chart specifications. Check that all cotter pins are installed securely to ensure equipment is in a safe condition before putting unit into service.

Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.)

Make sure shields and guards are properly installed and in good condition. Replace if damaged.

Never perform service or maintenance with engine running.

Do not disconnect hydraulic lines until machine is securely blocked or placed in lowest position and system pressure is released by operating valve levers.

Service and maintenance work not covered in OWNER SERVICE must be done by a qualified dealership. Special skills, tools, and safety procedures may be required. Failure to follow these instructions can result in serious injury or death.

Explosive separation of tire and rim parts can cause serious injury or death. Release all air pressure before loosening bolts on wheel.

STORAGE

Before disconnecting and storing, follow these instructions:

Store on level, solid ground.

Disconnect driveline and secure up off the ground.

Lower wings to ground.

Raise cutter center section and pin transport bar in raised position.

Attach parking jack and raise tongue weight off tractor drawbar.

Place wedge blocks at front and rear of wheels on center section and each wing to prevent wheel rotation.

Securely block all four corners of center section and each wing with jackstands.

Remove hydraulic hoses after tractor is turned off and all system pressure is released by operating valve levers several times.

Remove safety tow chain.

Remove retainer pin and high strength drawbar pin.

Keep children and bystanders away from storage area.

10 Safety

BW180_SR (Rev. 12/10/2007)

Woods Equipment BW180XHDQ, BW180XHD, BW126XHD, BW126XHDQ User Manual

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

MODEL NO.

SERIAL NO.

 

Woods Equipment Company

 

Oregon, Illinois, U.S.A.

1 - SERIAL NUMBER PLATE

PN 1006348 - Located on Wheel Rims

BE CAREFUL!

Use a clean, damp cloth to clean safety decals.

Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edges of decals causing them to peel or come off.

Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the

Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

2- FRONT AMBER REFLECTOR (PN 1002940)

3- REAR RED REFLECTOR (PN 57123)

4 - PN 18869

DANGER

SHIELD MISSING

18869-B

DO NOT OPERATE - PUT SHIELD ON

 

MAN0963 (2/16/2012)

Safety 11

 

 

 

WARNING
Check for leaks with cardboard; never use hand.
Before loosening fittings: lower load, release pressure, and be sure oil is cool.
Consult physician immediately if skin penetration occurs.
18865--C
15922-C

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

WARNING

DO NOT EXCEED PTO SPEED OF

1000 RPM

PTO speeds higher than 1000 RPM can cause equipment failure and personal injury.

5- PN 15922 (1000 RPM)

OR

WARNING

 

 

6 - PN 18866

(540 RPM)

540 RPM

 

 

 

! " #$

 

18866-D

8 - PN 18864

DANGER

ROTATING DRIVELINE

CONTACT CAN CAUSE DEATH

KEEP AWAY!

DO NOT OPERATE WITHOUT -

All driveline guards, tractor and equipment shields in place

Drivelines securely attached at both ends

Driveline guards that turn freely on

driveline

18864-C

 

9 - PN 18865

WARNING

FALLING OFF CAN RESULT IN BEING RUN OVER.

Tractor must be equipped with ROPS (or ROPS CAB) and seat belt. Keep foldable ROPS systems in “locked up” position at all times.

Buckle Up! Keep seat belt securely fastened.

Allow no riders.

RAISED EQUIPMENT CAN DROP AND CRUSH.

Before working underneath, follow all instructions and safety rules in operator’s manual and securely block up all corners of equipment with jack stands.

Securely blocking prevents equipment dropping from hydraulic leakdown, hydraulic system failures or mechanical component failures.

FALLING OFF OR FAILING TO BLOCK SECURELY CAN RESULT IN SERIOUS INJURY OR DEATH.

11 - PN 19924

7 - PN 15503

DANGER

ROTATING BLADES AND

THROWN OBJECTS

Do not put hands or feet under or into mower when engine is running.

Before mowing, clear area of objects that may be thrown by blade.

Keep bystanders away.

Keep guards in place and in good condition.

BLADE CONTACT OR THROWN OBJECTS CAN CAUSE SERIOUS INJURY OR DEATH.

 

 

15503-C

 

 

 

 

 

17 - PN 1004114

 

 

 

 

 

 

 

DANGER

 

 

 

If shaft connection is visible, shield

 

 

is missing. Replace shield before

 

 

operating equipment.

1004114

 

 

 

 

 

12 Safety

MAN0963 (2/16/2012)

 

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

12 - PN 1004991

WARNING

 

 

 

 

AND CYLINDER

 

 

 

 

TRANSPORT LOCK

 

RAISED CUTTER CAN DROP AND CRUSH

REQUIREMENTS

 

 

 

Cutters must be equipped with transport lock.

 

SINGLE-ACTING FULL

 

 

 

 

EXTENSION

 

stands.

 

 

28-

 

 

 

 

1/4"

 

All transport components must be functional, kept in good

 

 

Blocking up prevents cutter dropping from hydraulic leak down,

 

hydraulic system failures, or mechanical component failures.

 

 

FAILURE TO FOLLOW INSTRUCTIONS CAN

 

TRANSPORT

1004991

RESULT IN SERIOUS INJURY OR DEATH.

 

LOCK

10 - PN 33347

13 - PN 1003751

 

14 - PN 18877

 

WARNING

 

 

WARNING

 

 

 

 

 

 

 

TO AVOID SERIOUS

 

 

 

 

INJURY OR DEATH:

 

CRUSHING AND PINCHING HAZARD

Read Operator's Manual (available

 

from dealer) and follow all safety

 

Be extremely careful handling various parts of

 

 

precautions.

 

the machine. They are heavy and hands, fingers,

 

 

 

Keep all shields in place and in good

 

feet, and other body parts could be crushed or

 

condition.

 

pinched between tractor and implement.

 

 

Operate mower from tractor seat only.

 

Operate tractor controls from tractor seat only.

 

 

Lower mower, stop engine and remove

 

Do not stand between tractor and implement

 

 

key before dismounting tractor.

 

 

 

 

 

when tractor is in gear.

 

 

Allow no children or untrained persons

 

Make sure parking brake is engaged before

 

 

to operate equipment.

 

going between tractor and implement.

 

Do not transport towed or

 

Stand clear of machine while in operation or

 

semi-mounted units over 20 mph.

33347E

when it is being raised or lowered.

 

 

 

 

FAILURE TO FOLLOW THESE

 

 

FAILURE TO OPERATE SAFELY

 

 

CAN RESULT IN

INSTRUCTIONS COULD RESULT IN

 

 

 

 

 

INJURY OR DEATH.

 

SERIOUS INJURY OR DEATH.

 

 

 

1003751-A

 

18877-C

15 - PN 18964

 

16 - PN 15502

 

 

 

WARNING

 

 

WARNING

 

RAISED WING EXPOSES BLADE AND

 

ROTATING COMPONENTS

 

INCREASES THROWN OBJECT HAZARDS.

 

 

Only raise for transport. Stop cutter and

 

Do not operate without cover in place.

 

lock wing(s) up.

 

 

 

Look and listen for rotation. Do not

 

RAISED WING CAN FALL AND CRUSH.

 

 

 

open cover until all components have

 

Keep away.

 

 

 

stopped.

 

Lock up with wing transport bars.

 

 

 

 

 

 

Lower wing(s) after transport and for

 

CONTACT WITH ROTATING PARTS

 

storage.

 

 

 

CAN CAUSE SERIOUS INJURY.

 

FAILURE TO FOLLOW INSTRUCTIONS CAN

 

 

 

 

15502--B

18964-A

RESULT IN SERIOUS INJURY OR DEATH.

 

 

 

 

 

 

 

MAN0963 (2/16/2012)

 

 

 

Safety 13

 

 

 

 

OPERATION

The designed and tested safety of this machine depends on it being operated within the limitations as explained in this manual. Be familiar with and follow all safety rules in the manual, on the cutter and on the tractor.

The safe operation of this cutter is the responsibility of the operator, who must be properly trained. The operator should be familiar with the equipment and all safety practices before starting operation. Read the safety information on page 7 through page 13.

Recommended tractor ground speed for most conditions is from 1 to 6 mph.

Always operate tractor PTO at 540 rpm on BW180XHD and BW126XHD; on BW180XHDQ and BW126XHDQ operate PTO at 1,000 rpm.

Full chain or rubber shielding must be installed when operating in populated areas or other areas where thrown objects could injure people or damage property.

If this machine is not equipped with full chain or rubber shielding, operation must be stopped when anyone comes within 300 feet (92 m).

This shielding is designed to reduce the risk of thrown objects. The mower deck and protective devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. It is possible for objects to ricochet and escape, traveling as much as 300 feet (92 m).

Never allow children or untrained persons to operate equipment.

Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment.

Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

CAUTION

Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear

sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

CONNECTING CUTTER TO TRACTOR

NOTICE

For tractors with a 1-3/8" diameter PTO shaft, the horizontal distance from the end of the tractor PTO shaft to the center of drawbar pin should be 14" for 540 rpm cutter and 16" for the 1000 rpm cutters. This will minimize joint knock and damage to drive components.

NOTE: Remove CV drive shipping bracket before operation and discard. This bracket is only supplied on factory assembled units with a CV drive installed.

Figure 1. Cutter to Tractor Connection

1.Attach cutter using a 1-1/2" clevis pin and clip.

2.Attach safety tow chain (32) to drawbar support. Leave enough slack for turning (Figure 1).

3.Connect cutter driveline to tractor PTO shaft, making sure the spring-activated lock pin slides freely and is seated in tractor PTO splined groove.

4.Attach driveline shield tether chain to tractor drawbar to prevent rotation.

NOTE: CV driveline does not require a tether chain.

5.Remove parking jack (29) from the tongue and attach it to the storage post on the front of the left wing.

NOTE: Equal Angle Drive Only: With cutting height established, adjust the 3-joint H-frame bearing height so that the front driveline is parallel to the ground.

14 Operation

MAN0963 (2/16/2012)

 

Hydraulic Connection

1.Inspect hydraulic hoses to ensure they are in good condition.

2.Clean the fittings before connecting them to the tractor hydraulic ports.

3.Route the hose through the hose holder at the hitch and be sure the hose can slide freely in the holder. Do not allow hose slack to drag on the ground or become caught on tractor protrusions.

4.Attach the hydraulic hose to the tractor.

5.From the operator position, start tractor and raise and lower deck several times to purge trapped air from the hydraulic cylinder.

Interference Check

1.Be sure that tractor 3-point lift links do not interfere with hydraulic hoses, cutter driveline, or cutter frame.

2.Check for straight-ahead operation and at full turning angles. If there is any interference, remove the lower lift links.

3.Contact between tractor lift links and cutter parts can cause damage, especially when turning.

CV Driveline Turning Limits

NOTICE

You must not exceed a turning angle of 80 degrees at the head of the Constant Velocity driveline or damage will occur.

NOTE: Remove CV drive shipping bracket before operation and discard. This bracket is only supplied on factory assembled units with a CV drive installed.

1.To check for potential excessive turn angle, disconnect the driveline from tractor.

2.Start engine and turn as far right or left as possible.

3.Shut engine off and try to connect CV driveline to tractor. If it cannot be connected, the turn angle is too severe.

4.Restart engine and straighten angle slightly, shut off engine and try to connect CV driveline to tractor.

5.Repeat the process until the driveline can be connected. The point at which the driveline can be connected is the maximum turn that should be made.

Cutting Height Adjustment

On pull-type or semi-mounted units with optional hydraulic cutting height adjustment, use a single-acting cylinder with a maximum extended length of 28-1/4" (718 mm) from attaching point center to center.

NOTICE

Avoid ground contact with blades. Striking ground with blades produces one of the most damaging shock loads a cutter can encounter. If this occurs repeatedly, the cutter, driveline, and gearboxes will be damaged.

Cutting height range is from 1" to 15". A hydraulic cylinder or ratchet jack is available for cutting height adjustment.

When selecting a cutting height, you should consider the area of operation. If the ground is rolling and has mounds the blades could contact, set the cutting height accordingly. The cutting height (blade edge) is approximately 1" above the bottom of the side skid.

Cutting Height (Normal Mowing) - Center Section

1.Position the cutter on a hard level surface and select an approximate cutting height, Example 6".

2.Raise wings and lock them in the UP position.

3.Use any of the optional cutting height mechanisms to raise or lower the center section to obtain a distance of 5" from bottom edge of skid shoe to the ground.

4.Loosen jam nuts on the attitude rod that runs from the wheel yoke to the tongue.

5.Adjust rod in or out until the rear of the cutter is approximately 1/2" higher than the front.

6.Tighten jam nuts against sleeve.

Cutting Height (Normal Mowing) - Wings

1.Lower wings to normal mowing position.

2.Loosen the jam nut on the adjustable link (turn buckle).

3.Lengthening the link will raise the wing, shortening the link will lower the wing. The rear edge of the wing should be parallel to the ground.

When using the cutter to shred, the rear of the cutter deck should be approximately 1/2" to 1" lower than the front.

NOTE: Equal Angle Drive Only: With the cutting height established, adjust the driveline carrier bearing in the H-frame to ensure the front driveline is parallel to the ground with cutter in cutting position.

MAN0963 (2/16/2012)

Operation 15

 

 

 

TRACTOR OPERATION

Use care when operating around tree limbs and other low objects. Avoid being knocked off tractor and being injured.

Only use a tractor with a Roll Over Protection Structure (ROPS) and seat belt. Securely fasten seat belt.

The cutter is operated with tractor controls. Engage the PTO at a low rpm to prevent excessive loads on the cutter drive system. Increase throttle to recommended PTO operating RPM.

Be sure operator is familiar with all controls and can stop tractor and cutter quickly in an emergency. The operator should give complete, undivided attention to operating tractor and cutter.

CUTTER OPERATION

When beginning operation of the cutter, make sure that all persons are in a safe location.

Power for operating the cutter is supplied by the tractor PTO. Operate PTO at 540 (1000 RPM for "Q" models).

Know how to stop the tractor and cutter quickly in an emergency.

Engage PTO at a low engine, rpm to minimize stress on the drive system and gearbox.

With PTO engaged, raise PTO speed to 540 or 1000 RPM depending on model and maintain throughout cutting operation.

Gearbox protection is provided by a slip clutch with replacement fiber disc. The slip clutch is designed to slip when excessive torsional loads occur.

Move slowly into material. Adjust tractor ground speed to provide a clean cut without lugging the tractor engine.

Use a slow ground speed for better shredding.

Proper ground speed will depend on the terrain and the material’s height, type, and density.

Normally, ground speed will range from 2 to 5 mph. Tall, dense material should be cut at a low speed; thin, medium-height material can be cut at a faster ground speed.

Always operate tractor PTO at proper RPM (540 or 1000 depending on model) to maintain blade speed and to produce a clean cut.

Under certain conditions tractor tires may roll down some grass and prevent cutting at the same height as the surrounding area. When this occurs, reduce your ground speed but maintain PTO at 540 or 1000 RPM. The lower ground speed will permit grass to rebound partially.

Mowing Tips

Look down and to the rear and make sure area is clear before operating in reverse.

Do not operate or transport on steep slopes.

Do not stop, start, or change directions suddenly on slopes.

Use extreme care and reduce ground speed on slopes and rough terrain.

Watch for hidden hazards on the terrain during operation.

CAUTION

Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

Maximum recommended ground speed for cutting or shredding is 6 miles per hour. Adjust tractor ground speed by using higher or lower gears to provide a clean cut without lugging tractor engine.

Tall material should be cut twice. Cut material higher the first pass. Cut at desired height at 90 degrees the second pass.

Remember, sharp blades produce cleaner cuts and use less power.

Before entering an area, analyze it to determine the best procedure. Consider the height and type of material to be cut and the terrain type (hilly, level or rough, etc.).

Shredding

The cutter may be used to shred various crops including green manure, straw, stubble, asparagus residue, corn stalks and similar crops in preparation for tilling. It may also be used to shred pruning in orchards, groves and vineyards.

Each shredding operation may require a different setup. Start with front edge of cutter high. Adjust up or down as necessary with attitude rod. Experiment until you obtain the results you want.

When shredding attitude is set, check that the distance from the bottom rear edge of the wing to the ground matches the bottom edge of the rear center section to the ground. With the cutting height and attitude established, adjust the driveline carrier bearing in the H- frame to ensure the front driveline is parallel to the ground.

16 Operation

MAN0963 (2/16/2012)

 

TRANSPORTING

Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.

Always raise unit and install transport locks before transporting. Leak down or failure of mechanical or hydraulic system can cause equipment to drop.

Always attach safety chain to tractor drawbar when transporting unit.

Never exceed 20 mph (32.2 km/h) during transport.

Never allow riders on power unit or attachment.

Do not operate PTO during transport.

Do not operate or transport on steep slopes.

Do not operate or transport equipment while under the influence of alcohol or drugs.

CAUTION

Always comply with all state and local lighting and marking requirements.

Lock-Up

Always transport with wings and center frame in the raised, locked position.

Wing Lock-Up

1.Raise wing to the up position.

2.Remove safety pin and lock-up bar from storage position.

3.Place lock-up bar over cylinder pin and secure with safety pin.

4.Repeat steps 1 to 3 for opposite wing.

5.Lower cylinder against lock-up bars (Figure 2).

DP4a

Figure 2. Transport Lock-Up Bar - Right Wing

Center Section Lock-Up

1.Raise cutter with hydraulic cylinder to maximum height.

2.Rotate transport lock into position over cylinder rod (Figure 3).

DP7

Figure 3. Transport Lock In Transport Position

3.Lower cutter against transport lock.

4.To lower cutter for operation, extend hydraulic cylinder to raise cutter. Rotate transport lock back away from cylinder rod (Figure 4).

5.Lower cutter to desired cutting height.

Figure 4. Transport Lock In Operation Position

MAN0963 (2/16/2012)

Operation 17

 

 

 

STORAGE

Follow these steps when storing your cutter:

1.Clean cutter before storing. See page 23 for cleaning instructions. Store on level, solid ground.

2.Disconnect driveline and secure up off the ground.

3.Lower wings to ground.

4.Raise cutter center section and pin transport bar in raised position.

5.Attach parking jack and raise tongue weight off tractor drawbar.

6.Place wedge blocks at front and rear of wheels on center section and each wing to prevent wheel rotation.

7.Securely block all four corners of center section and each wing with jack stands.

8.Remove hydraulic hoses after tractor is turned off and all system pressure is released by operating valve levers several times.

9.Remove safety tow chain.

10.Remove retainer pin and high strength drawbar pin.

11.Keep children and bystanders away from storage area.

PRE-OPERATION CHECK LIST

(OWNER'S RESPONSIBILITY)

___ Review and follow all safety rules and safety decal instructions on page 7 through page 13.

___ Check that all safety decals are installed and in good condition. Replace if damaged.

___ Check that equipment is properly and securely attached to tractor.

___ Make sure driveline spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

___ Check all lubrication points and grease as instructed in lubrication information. Make sure

 

the PTO slip joint is lubricated and that the gear-

 

box fluid levels are correct.

___

Set tractor PTO at correct rpm for your equip-

 

ment.

___

Lubricate all grease fitting locations. Make sure

 

PTO shaft slip joint is lubricated.

___

Check that all hydraulic hoses and fittings are in

 

good condition and not leaking before starting

 

tractor. Check that hoses are not twisted, bent

 

sharply, kinked, frayed, or pulled tight. Replace

 

any damaged hoses immediately.

___

Check that all hardware is properly installed and

 

secured.

___

Check cutting height and attitude adjustment.

___

Raise and lower equipment to make sure air is

 

purged from hydraulic cylinders and hoses. Raise

 

and lower equipment to make sure air is purged

 

from hydraulic cylinders and hoses.

___

Check that blades are sharp and secure and cut-

 

ting edge is positioned to lead in a counterclock-

 

wise rotation.

___

Make sure tractor ROPS or ROPS cab and seat

 

belt are in good condition. Keep seat belt

 

securely fastened during operation.

___ Check that shields and guards are properly installed and in good condition. Replace if damaged.

___ Before starting engine, operator must be in tractor seat with seat belt fastened. Place transmission in neutral or park, engage brake and disengage tractor PTO.

___ Inspect area to be cut and remove stones, branches, or other hard objects that might be

 

thrown and cause injury or damage.

___

Inspect rubber or chain shielding and replace any

 

damaged rubber shield or missing links.

___

Make sure tractor 3-point lift links do not interfere

 

with hydraulic hoses or driveline throughout full

 

turning range.

18 Operation

MAN0963 (2/16/2012)

 

OWNER SERVICE

The information in this section is written for operators who possess basic mechanical skills. If you need help, your dealer has trained service technicians available. For your protection, read and follow the safety information in this manual.

Keep all persons away from operator control area while performing adjustments, service, or maintenance.

Before working underneath, disconnect driveline from tractor, lower wings to ground, raise cutter, and pin transport bar in raised position. Attach parking jack and lower to ground. Securely block all four corners of center section and each wing with jack stands. Blocking up prevents the cutter from dropping due to hydraulic leak down, hydraulic system failure, or mechanical component failure.

Service and maintenance work not covered in OWNER SERVICE must be done by a qualified dealership. Special skills, tools, and safety procedures may be required. Failure to follow these instructions can result in serious injury or death.

Before servicing, adjusting, repairing or unplugging, stop tractor engine, place all controls in neutral, set park brake, remove ignition key, and wait for all moving parts to stop.

Never perform service or maintenance with engine running.

CAUTION

If you do not understand any part of this manual and need assistance, see your dealer.

Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

BLOCKING METHOD

To minimize the potential hazards of working underneath the cutter, follow these procedures:

Before performing any service or maintenance, lower equipment to ground or block securely, turn off engine, remove key, and disconnect driveline from tractor PTO.

Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body underneath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death. Follow Operator's Manual instructions for working underneath and blocking requirements or have work done by a qualified dealer.

Do not position jackstands under wheels, axles, or wheel supports. Components can rotate and cause cutter to fall.

1.Jackstands with a load rating of 1000 lbs. or more are the only approved blocking device for this cutter. Install jackstands (shown by Xs in Figure 5) under the cutter before working underneath unit.

2.Consider the overall stability of the blocked unit. Just placing jackstands underneath will not ensure your safety.

The working surface must be level and solid to support the weight on the jackstands. Make sure jackstands are stable, both top and bottom. Make sure cutter is approximately level.

3.With full cutter weight lowered onto jackstands, test blocking stability before working underneath.

4.If cutter is attached to tractor when blocking, set the brakes, remove key, and block cutter before working underneath.

5.Securely block rear tractor wheels, in front and behind. Tighten tractor lower 3-point arm anti-sway mechanism to prevent side-to-side movement.

MAN0963 (2/16/2012)

Owner Service 19

 

 

1.

Driveline U-joint

10 Hours

7.

Gearbox (above lower

Daily

2.

Telescoping shaft

10 Hours

 

line on dipstick)

 

3.

Carrier bearing block

40 Hours

8.

Tongue pivot

40 Hours

4.

CV body assembly

10 hours

9.

Wheel yoke pivot

40 Hours

 

(10 pumps minimum)

 

10.

Tailwheel spindle

20 Hours

5.

Driveline shield

10 Hours

11.

Turnbuckle

40 Hours

6.

Splined yoke

10 Hours

 

 

 

Figure 5. Jackstand Placement and Lubrication Points

LUBRICATION

Do not let excess grease collect on or around parts, particularly when operating in sandy areas.

See Figure 5 for lubrication points and frequency or lubrication based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication.

Use a lithium grease of #2 consistency with a MOLY (molybdenum disulfide) additive for all locations unless otherwise noted. Be sure to clean fittings thoroughly before attaching grease gun. One good pump of most guns is sufficient when the lubrication schedule is followed.

Gearbox Lubrication

For gearbox, use a high quality gear oil with a viscosity index of 80W or 90W and an API service rating of GL–

4 or –5 in gearboxes. Fill gearbox until oil runs out the side plug on gearbox. Check gearbox daily for evidence of leakage, and contact your dealer if leakage occurs. Use sealant on vent plug threads during installation. Check vent plug periodically and clean if it does not relieve pressure.

Driveline Lubrication

1.Lubricate the driveline slip joint every eight operating hours. Failure to maintain proper lubrication could result in damage to U-joints, gearbox, and driveline.

2.Lower cutter to ground, disconnect driveline from tractor PTO shaft, and slide halves apart but do not disconnect from each other.

3.Apply a bead of grease completely around male half where it meets female half. Slide drive halves over each other several times to distribute grease.

20 Owner Service

MAN0963 (2/16/2012)

 

 

Seasonal Lubrication

In addition to the daily recommended lubrication, a more extensive application is recommended seasonally.

1.Fill CV double yokes with 20 pumps of grease with the joints in a straight line.

2.Articulate CV body to maximum angle several times to ensure full coverage of joints.

3.Place joints in the straight position and a add 10 additional pumps of grease to both joints.

4.Wipe telescoping drive clean of all old grease and contaminants.

5.Add a thin layer of new grease over telescoping drive.

BLADES

Before working underneath, read manual instructions, securely block up, and check stability. Secure blocking prevents equipment from dropping due to hydraulic leak down, hydraulic system failure, or mechanical component failure.

Blade Removal (Figure 6)

9.Blade pin

10.Crossbar assembly

11.Shim, 18 ga

12.Shim, 20 ga

13.Keyhole plate

14.Blade lock clip

52.1/2 NC x 1-1/4 HHCS GR5

Figure 6. Blade Assembly

1.Disconnect driveline from tractor PTO.

2.Raise cutter and block securely (see Figure 5).

3.Align crossbar (10) with blade access hole in the cutter frame. Remove cap screw (52), blade pin

lock clip (14), keyhole plate (13), and shims (11 & 12). Carefully drive blade pin (9) out of crossbar.

4. Rotate crossbar and repeat for opposite blade.

NOTICE

If blade pin (9) is seized in crossbar and extreme force will be needed to remove it, support crossbar from below to prevent gearbox damage.

Blade Installation (Figure 6)

CAUTION

Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous.

NOTICE

Crossbar rotation has clockwise rotation on left gearbox and counterclockwise rotation on the right and center gearboxes when looking down on cutter. Be sure to install blade cutting edge to lead in correct rotation.

NOTE: Always replace or sharpen both blades at the same time.

1.Inspect blade pin (9) for nicks or gouges, and if you find any replace the blade pin.

2.Insert blade pin through the blade. Blade should swivel on blade pin; if it doesn’t, determine the cause and correct.

3.Align crossbar (10) with blade access hole in cutter frame. Apply a liberal coating of Never-Seez® or equivalent to blade pin and crossbar hole. Make sure blade offset is down away from cutter.

4.Insert blade pin (9) through blade. Push blade pin through crossbar.

5.Install shims (11 & 12) over blade pin.

NOTE: Only use enough shims to allow keyhole plate (13) to slide into blade pin groove.

6.Install blade clip (14) over keyhole plate and into blade pin groove.

7.Secure into position with cap screw (52). Torque cap screw to 85 lbs-ft.

8.Repeat steps for opposite side.

NOTE: Blade should be snug but should swivel on pin without having to exert excessive force. Blade should not move more than a 1/4 inch up or down at the tip. Keep any spacers not used in the installation as replacements or for future installation.

MAN0963 (2/16/2012)

Owner Service 21

 

 

Blade Sharpening

NOTICE

When sharpening blades, grind the same amount on each blade to maintain balance. Replace blades in pairs. Unbalanced blades will cause excessive vibration, which can damage gearbox bearings. Vibration may also cause structural cracks to cutter.

1.Sharpen both blades at the same time to maintain balance. Follow original sharpening pattern.

2.Do not sharpen blade to a razor edge—leave at least a 1/16" blunt edge.

3.Do not sharpen back side of blade.

Figure 7. Blade Sharpening

SLIP CLUTCH ADJUSTMENT (FIGURE 8)

The slip clutch is designed to slip so that the gearbox and driveline are protected if the cutter strikes an obstruction.

A new slip clutch or one that has been in storage over the winter may seize. Before operating the cutter, make sure it will slip by performing the following operation:

1.Turn off tractor engine and remove key.

2.Remove driveline from tractor PTO.

3.Loosen six 10 mm cap screws (6) to remove all tension from Belleville spring plate (5).

4.Hold clutch hub (3) solid and turn shaft to make sure clutch slips.

5.If clutch does not slip freely, disassemble and clean the thrust plate faces (4), flange yoke (1), and clutch hub (3).

6.Reassemble clutch.

7.Tighten Belleville spring (5) until it is against the thrust plate (4) of the clutch, and then back off each of the six nuts by 2 full revolutions. The gap between Belleville spring and thrust plate should be 1/8" as shown in Figure 8.

8.If a clutch continues to slip when the spring is compressed to 1/8" gap, check friction discs (2) for excessive wear. Discs are 1/8" when new. Replace discs after 1/16" wear. Minimum disc thickness is 1/16".

1.Flange yoke

2.Friction disc

3.Hub 1-3/8 round bore

4.Thrust plate

5.Belleville spring plate

6.10 mm x 1.5P x 50 mm Cap screw

7.10 mm x 1.5P Hex nut

8.12 mm x 1.5P x 65 mm Cap screw

9.12 mm x 1.5P Hex nut

Figure 8. Slip Clutch Assembly

22 Owner Service

MAN0963 (2/16/2012)

 

 

SHIELDING REPAIR

Full chain or rubber shielding must be installed when operating in populated areas or other areas where thrown objects could injure people or damage property.

If this machine is not equipped with full chain or rubber shielding, operation must be stopped when anyone comes within 300 feet (92 m).

This shielding is designed to reduce the risk of thrown objects. The mower deck and protective devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. It is possible for objects to ricochet and escape, traveling as much as 300 feet (92 m).

Repairing Rubber Shielding

1.Inspect belting and rear bands each day of operation.

2.Replace if bent, cracked, or broken.

3.Replace any missing hardware.

Repairing Optional Chain Shielding:

1.Inspect chain shielding each day of operation and replace any broken or missing chains as required.

2.Replace any missing hardware.

SERVICING TIRES SAFELY

Used Aircraft Tires (Figure 9)

WARNING

Do not attempt to mount a tire unless you have the proper equipment and experience to perform the job.

Always maintain the correct tire pressure. Do not inflate tires above the recommended pressure. Never weld or heat a wheel and tire assembly. The heat can cause an increase in air pressure and result in a tire explosion. Welding can structurally weaken or deform the wheel.

When inflating tires, use a clip-on chuck and an extension hose long enough to allow you to stand to the side

— not in front of or over the tire assembly. Use a safety cage if available.

Check wheels for low pressure, cuts, bubbles, damaged rims, or missing lug bolts and nuts.

Never remove split rim assembly hardware (A) with the tire inflated.

A

PN 1006348

Figure 9. Split Rim Tire Servicing

CLEANING

After Each Use

Remove large debris such as clumps of dirt, grass, crop residue, etc. from machine.

Inspect machine and replace worn or damaged parts.

Replace any safety decals that are missing or not readable.

Periodically or Before Extended Storage

Clean large debris such as clumps of dirt, grass, crop residue, etc. from machine.

Remove the remainder using a low-pressure water spray.

1.Be careful when spraying near scratched or torn safety decals or near edges of decals as water spray can peel decal off surface.

2.Be careful when spraying near chipped or scratched paint as water spray can lift paint.

3.If a pressure washer is used, follow the advice of the pressure washer manufacturer.

Inspect machine and replace worn or damaged parts.

Sand down scratches and the edges of areas of missing paint and coat with Woods spray paint of matching color (purchase from your Woods dealer).

Replace any safety decals that are missing or not readable (supplied free by your Woods dealer). See Safety Decals section for location drawing.

MAN0963 (2/16/2012)

Owner Service 23

 

 

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

SOLUTION

 

 

 

Does not cut

Dull blades

Sharpen blades.

 

Worn or broken blades

Replace blades. (Replace in pairs

 

 

only.)

 

Incorrect PTO speed

Set at rated PTO speed.

 

Ground speed too fast

Reduce ground speed.

 

Drive not functioning (blades do

Check drive shaft connection.

 

not turn when PTO is running)

Check gearbox.

 

Gearbox malfunction

Repair gearbox.

 

Excessive clutch slippage

Adjust clutch.

 

Incorrect blade direction

Check to be sure blade edge is

 

 

correct for direction of rotation.

 

 

 

Streaks or ragged cut

Broken or worn blades

Replace or sharpen blades.

 

Attitude incorrect

Level machine.

 

Ground speed too fast

Reduce ground speed.

 

Excessive cutting height

Lower cutting height. (Note: Set

 

 

height so blades do not frequently

 

 

hit ground.)

 

Excessive lush and tall vegetation

Recut at 90° to first pass.

 

 

 

Excessive side skid wear

Running with skids continuously

Raise cutting height or adjust.

 

on ground

 

 

 

 

Excessive clutch slippage

Clutch out of adjustment

Adjust clutch.

 

Clutch discs worn; wear stops

Replace discs.

 

contacting opposite plate

 

 

Blades hitting ground

Raise cutting height.

 

 

 

Vibration

Broken blade

Replace blades in pairs.

 

Bearing failure

Check gearbox shafts for side play.

 

Hitch length incorrect

Reset hitch length.

 

Universal drive

Adjust pedestal bearing height to

 

 

be parallel to ground.

 

 

 

Blades hitting deck

Bent blades or crossbar

Replace bent blades or crossbar.

 

 

 

Unit will not raise

Low oil

Add hydraulic oil.

 

 

 

Unit doesn’t cut level

Wing section cuts lower than

Lengthen turnbuckle connecting

 

center

center yoke to wing wheel yoke.

 

Wing section cuts higher than

Shorten turnbuckle connecting

 

center

center yoke to wing wheel yoke.

 

 

 

24 Troubleshooting

MAN0963 (2/16/2012)

 

 

DEALER SERVICE

The information in this section is written for dealer service personnel. The repair described here requires special skills and tools. If your shop is not properly equipped or your mechanics are not properly trained in this type of repair, you may be time and money ahead to replace complete assemblies.

Before working underneath, read manual instructions, securely block up, and check stability. Secure blocking prevents equipment from dropping due to hydraulic leak down, hydraulic system failure, or mechanical component failure.

Keep all persons away from operator control area while performing adjustments, service, or maintenance.

CAUTION

Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

GEARBOX MAINTENANCE - STYLE A

NOTE: Read this entire section (pages 25 - 28) before starting any repair. Many steps are dependent on each other. See parts list on pages 62 thru 65 to determine gearbox style. Style "A" has a crowned top. Style"B" has a flat top.

1.Fill gearbox with SAE 80W or 90W gear lube. Proper oil level is between lowest ring and end of dipstick.

NOTE: Replacing gears, shafts, and housing may not be cost effective. Purchasing a complete gearbox may be more economical.

2.Inspect gearbox for leakage and bad bearings. Leakage is a very serious problem and must be corrected immediately.

NOTE: Bearing failure is indicated by excessive noise and side-to-side or end-play in gear shafts.

Seal Replacement (Figure 11)

Recommended sealant for gearbox repair is Permatex® Aviation 3D Form-A-Gasket or equivalent.

Leakage can occur at the vertical or horizontal gaskets and shaft seals.

Leakage at the horizontal gasket or seal can be repaired without removing the gearbox from the cutter.

Seal Installation

NOTE: Proper seal installation is important. An improperly installed seal will leak.

1.Clean area in housing where seal outer diameter (OD) seats. Apply a thin coat of Permatex.

2.Inspect area of shaft where seal seats. Remove any burrs or nicks with an emery cloth.

3.Lubricate gear shaft and seal lips.

4.Place seal squarely on housing, spring-loaded lip toward housing. Select a piece of pipe or tubing with an OD that will sit on the outside edge of the seal but will clear the housing. Tubing with an OD that is too small will bow seal cage and ruin seal.

5.Carefully press seal into housing, avoiding distortion to the metal seal cage.

1.Seal

2.Pipe or tube

3.Seal seat

4.Casting

Pipe or tube must press at outer edge of seal.

Incorrect

Installation

Figure 11. Seal Installation

MAN0963 (2/16/2012)

Dealer Service 25

 

 

Vertical Shaft Seal Replacement

Refer to Figure 12, page 28.

1.Disconnect and remove the driveline from the gearbox.

2.Remove dipstick breather assembly (30) and siphon gear lube from housing through this opening.

3.Remove crossbar (see page 36).

4.Remove retaining ring (33) and output oil seal (15). Replace output oil seal (15) with new seal. Install retaining ring (33).

NOTE: Distortion to seal cage or damage to seal lip will cause seal to leak.

5.Fill gearbox with SAE 80W or 90W gear lube to the center of the horizontal shaft.

6.Remove and replace any seal damaged in installation.

Horizontal Shaft Seal Replacement

Refer to Figure 12.

1.Disconnect and remove the driveline from the gearbox.

2.Remove dipstick breather assembly (30) and siphon gear lube from housing through this opening.

3.Remove input oil seal (6). Replace with new one.

4.Fill gearbox with SAE 80W or 90W gear lube to the center of the horizontal shaft.

Gearbox Cap Leak Repair

Refer to Figure 12.

1.Disconnect and remove the driveline from the gearbox.

2.Remove dipstick breather assembly (30) and siphon gear lube from housing through this opening.

3.Remove cap where leak is occurring (4, 21 or 26).

4.Clean mating surfaces with a gasket remover.

5.Replace gaskets (7, 8, 22, 23) as required to meet the following specifications:

End float should be less than 0.012".

Rotational torque should be less than 2.2 lbsinch.

Gear backlash should be between 0.006" and 0.016".

6.Install cap (4, 21 or 26) using a gasket sealant.

7.Install cap screws (3 or 25) and torque to 29 lbs-ft.

8.Fill gearbox with SAE 80W or 90W gear lube to the center of the horizontal shaft.

GEARBOX REPAIR - STYLE A

Gearbox Removal From Cutter

NOTE: Gearbox is heavy: do not attempt to move without mechanical assistance.

1.Disconnect and remove the driveline from the gearbox that is to be removed.

2.Remove cotter pin and nut from vertical shaft and remove crossbar (see page 36).

3.Remove the eight bolts that attach gearbox to cutter and remove gearbox.

Gearbox Disassembly

Refer to Figure 12.

1.Remove six cap screws (25) and cover (26) from gearbox and pour out gear oil.

2.Remove caps (21 and 4).

3.Support gearbox in hand press and push on the gear end of the input shaft (5) to remove bearing (20).

4.Remove gear (32) from inside housing.

5.Remove bearing (20) by using a punch and hammer from outside of housing.

6.Support housing in vise in a horizontal position.

7.The castle nut (14), cotter pin (13), and hub were already removed with the stump jumper/crossbar. Remove the ring (33), and oil seal (15).

8.Remove cotter pin (19), nut (18) from output shaft (16).

9.Remove output shaft (16) by using a punch and hammer and tap on top to drive down. Remove gear (17) and shims (9, 10, 11) from inside housing.

10.Remove bottom bearing (12) by using a punch and hammer from the top, outside the housing.

11.Support housing upside down (top cover surface) and remove bearing (20) by using a punch and hammer from the bottom side of the housing.

12.Inspect gears for broken teeth and wear. Some wear is normal and will show on loaded side. Forged gear surfaces are rough when new. Check that the wear pattern is smooth.

13.Inspect vertical and horizontal shafts for grooves, nicks, or bumps in the areas where the seals seat. Resurface any damage with emery cloth.

26 Dealer Service

MAN0963 (2/16/2012)

 

 

Loading...
+ 60 hidden pages