Wolf ICBCT30E, ICBCT36EU, ICBCT30EU, ICBCT36E, ICBCT15E User Manual

ELECTRIC COOKTOPS

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN

INSTRUCTIONS D’INSTALLATION

ISTRUZIONI PER L’INSTALLAZIONE

INSTALLATIONSANWEISUNGEN

E N G L IS H	4
E S P Ã N O L	2 2
F R A N Ç A I S	4 0
I TA L I A N O	5 8
D E U T S C H	7 6

3

C O N TAC T

I N F O R M AT I O N

Website:

wolfappliance.com

WOLF® is a registered trademark of Wolf Appliance, Inc.

As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Wolf equipment. There are two types of potential hazards that may occur during installation.

signals a situation where minor injury or product damage may occur if you do not follow instructions.

states a hazard that may cause serious injury or death if precautions are not followed.

Another footnote we would like to identify is IMPORTANT NOTE: This highlights information that is especially relevant to a problemfree installation.

WOLF E L E C T R I C CO O K TO P S

I N S TA L LAT I ON REQUIREMENTS

IMPORTANT NOTE: Save these Installation Instructions for the local inspector’s use.

Please read the entire Installation Instructions prior to installation.

This installation must be completed by a qualified technician.

Installer: please retain these instructions for local inspector’s reference, then leave them with the homeowner.

Homeowner: please read and keep these instructions for future reference and be sure to read the entire Use & Care Information prior to use.

IMPORTANT NOTE: This appliance must be installed in accordance local codes. The correct voltage, frequency and amperage must be supplied to the appliance from a dedicated, grounded circuit which is protected by a properly sized circuit breaker or time delay fuse. The proper voltage, frequency, and power ratings are listed on the product rating plate.

Record the model and serial numbers before installing the cooktop. Both numbers are on the rating plate, located on the underside of the cooktop. Refer to the illustration below.

B E F O R E YOU START

Proper installation is your responsibility. Have a qualified technician install this cooktop. You must also assure that electrical installation is adequate and in compliance with all local codes and ordinances.

Installations and repairs must be performed by a qualified or licensed contractor or electrician qualified or licensed by the state, province, or region where this appliance is being installed.

Make sure you have everything necessary for correct installation. It is the responsibility of the installer to comply with the installation clearances specified in this book and on the product rating plate. The rating plate is located on the underside of the cooktop. Refer to the illustration below.

Electrical ground is required; see Electrical Requirements on page 16.

This cooktop is intended for indoor use.

Location of rating plate under cooktop

Rating plate location

RATING PLATE INFORMATION

Model Number

Serial Number

5

WOLF E L E C T R I C CO O K TO P S

S I T E PREPARATION

IMPORTANT NOTE: Installation of the Wolf electric cooktop must meet the following location requirements. All dimensions listed are minimum requirements for safe operation. Refer to the illustration below.

To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a ventilation hood that projects horizontally a minimum of 127 mm beyond the bottom cabinets.

C

G

D

E

B

F

A

B

Minimum clearances for installation

LOC ATION IN COUNTERTOP

A)Minimum flat countertop surface. Must be equal to or greater than cooktop width.

B)Minimum 25 mm wide clearance from the cooktop side edge to any combustible surface up to 457 mm above the cooktop (noted by shaded area).

OVERHEAD C ABINET DIMENSIONS

C)Minimum spacing between overhead side cabinets must be greater than or equal to the nominal width of the cooktop unit(s).

D)Minimum 457 mm vertical distance from the countertop to the bottom of side cabinets within minimum side clearance.

E)Minimum vertical distance between the countertop and combustible materials above the cooktop must be 762 mm.

F)Minimum 25 mm from rear wall.

G)Maximum 330 mm depth of overhead and side cabinets directly above and within side clearance.

Failure to locate the cooktop unit without the proper clearances will result in a fire hazard.

6

I N S TA L L AT I O N I N S T RU C T I O N S

I N S TA L L AT I O N S P E C I F I C AT I O N S

The illustrations on pages 8–13 provide the overall dimensions, installation specifications and countertop cut-out for each of the Wolf electric cooktop models.

These cooktops are designed to fit a standard 610 mm deep base cabinet with a 635 mm deep countertop. Before making the countertop cut-out, verify that the cooktop will clear the side walls of the base cabinet below.

Clearance is required for the terminal block and conduit located at the right rear of the cooktop. Refer to the illustration below for dimensions.

FRAMED ELECTRIC COOKTOPS

For framed models, a minimum 146 mm clearance is required between the countertop and any combustible surface directly below the cooktop.

Wolf framed electric cooktops are designed to be installed in combination with other cooktop units.

IMPORTANT NOTE: When multiple cooktop units are installed side by side, refer to the countertop cut-out dimensions on page 11.

Wolf framed electric cooktops can accommodate a Wolf downdraft ventilation system. Refer to installation instructions provided with the downdraft for additional specifications.

UNFRAMED ELECTRIC COOKTOPS

For unframed models, a minimum 159 mm clearance is required between the countertop and any combustible surface directly below the cooktop.

IMPORTANT NOTE: Unframed electric cooktops are not designed to be installed in combination with other cooktops.

IMPORTANT NOTE: Unframed electric cooktops cannot be installed with a downdraft ventilation system.

For installation options of the unframed electric cooktops, refer to Unframed Installations on pages 14–15.

32 mm

56 mm

22 mm

84 mm

24 mm

Terminal block dimensions

7

WOLF E L E C T R I C CO O K TO P S

FRAMED M O D E L I C B C T 1 5 E

The illustrations below provide installation specifications for Model ICBCT15E.

If Model ICBCT15E is installed above cabinets, the electrical placement is not critical. A grounded electrical box should be located within 1.2 m of the right rear of the cooktop.

For installation above an oven, unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven.

IMPORTANT NOTE: Do not block the cooling fan located at the bottom of the cooktop.

INSTALLATION SPECIFIC ATIONS – MODEL ICBCT15E

533 mm

OVERALL

DEPTH

381 mm

OVERALL WIDTH

96 mm

127 mm

TERMINAL BOX

Overall Dimensions

MODEL ICBCT15E

Overall Width

381 mm

Overall Height

96 mm

Overall Depth

533 mm

Minimum Cabinet Depth

578 mm

Minimum Height Clearance*

102 mm

Cut-Out Width

340 mm

Cut-Out Depth

489 mm

*Minimum 146 mm clearance is required between countertop and any combustible surface directly below the cooktop.

For detailed terminal block dimensions, refer to the illustration on page 7.

Dimensions may vary to ±3 mm.

330 mm
	max
51**	489 mm
mm COOKTOP CUT-OUT
	DEPTH

		838 mm RECOMMENDED		762 mm
457 mm	51 mm*min	CABINET WIDTH
		340 mm		COUNTERTOP TO
	CUT-OUT TO			COMBUSTIBLE
64 mm	COMBUSTIBLE	COOKTOP CUT-OUT		MATERIALS
	MATERIALS	WIDTH		ABOVE COOKTOP
min	(BOTH SIDES)
			102 mm
914 mm		E	381
			mm
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT		381 mm

NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.

340 mm

COOKTOP CUT-OUT

WIDTH

Countertop Cut-Out
								489 mm
		64 mm						COOKTOP
								CUT-OUT DEPTH
			min
						FRONT OF COUNTERTOP

8

I N S TA L LAT I ON INSTRUCTIONS

FRAMED M O D E L I C B C T 3 0 E

The illustrations below provide installation specifications for Model ICBCT30E.

For ease of installation, 838 mm cabinets are recommended for installation of Model ICBCT30E.

A Wolf 762 mm or 914 mm built-in single oven may be installed below Model ICBCT30E. For this installation, unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven.

Refer to installation instructions provided with the built-in oven for additional specifications.

If Model ICBCT30E is installed above cabinets, the electrical placement is not critical. A grounded electrical box should be located within 1.2 m of the right rear of the cooktop.

IMPORTANT NOTE: Do not block the cooling fan located at the bottom of the cooktop.

INSTALLATION SPECIFIC ATIONS – MODEL ICBCT30E
	533 mm
	OVERALL
	DEPTH
762 mm						838 mm RECOMMENDED
OVERALL WIDTH		330 mm						762 mm
						CABINET WIDTH
			max	457 mm	51 mm*min	762 mm min		COUNTERTOP TO
		51**	489 mm		CUT-OUT TO	721 mm COOKTOP		COMBUSTIBLE
					COMBUSTIBLE			MATERIALS
96 mm		mm COOKTOP CUT-OUT		64 mm
	127 mm				MATERIALS	CUT-OUT WIDTH		ABOVE COOKTOP
			DEPTH	min	(BOTH SIDES)
TERMINAL BOX						102 mm
Overall Dimensions						89 mm		E
						95 mm	254
			610 mm min	914 mm		min
							mm
				STANDARD
				FLOOR TO
				COUNTERTOP		762 mm OVEN OPENING
MODEL ICBCT30E				HEIGHT
Overall Width	762 mm
Overall Height	96 mm
Overall Depth	533 mm	*Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance
Minimum Cabinet Depth	578 mm	from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.
Minimum Height Clearance*	102 mm					721 mm
						COOKTOP CUT-OUT WIDTH
Cut-Out Width	721 mm	Countertop Cut-Out
Cut-Out Depth	489 mm

*Minimum 146 mm clearance is required			489 mm
between countertop and any combustible	64 mm		COOKTOP
			CUT-OUT DEPTH
surface directly below the cooktop.	min

For detailed terminal block dimensions, refer to the illustration on page 7.

FRONT OF COUNTERTOP

Dimensions may vary to ±3 mm.

9

WOLF E L E C T R I C CO O K TO P S

FRAMED M O D E L I C B C T 3 6 E

The illustrations below provide installation specifications for Model ICBCT36E.

For ease of installation, 991 mm cabinets are recommended for installation of Model ICBCT36E.

A Wolf 762 mm or 914 mm built-in single oven may be installed below Model ICBCT36E. For this installation, unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven.

Refer to installation instructions provided with the built-in oven for additional specifications.

If Model ICBCT36E is installed above cabinets, the electrical placement is not critical. A grounded electrical box should be located within 1.2 m of the right rear of the cooktop.

IMPORTANT NOTE: Do not block the cooling fan located at the bottom of the cooktop.

INSTALLATION SPECIFIC ATIONS – MODEL ICBCT36E
	533 mm
	OVERALL
	DEPTH
914 mm						991 mm
OVERALL WIDTH		330 mm						762 mm
						RECOMMENDED CABINET WIDTH
			max	457 mm	51 mm*min	914 mm min		COUNTERTOP TO
		51**	489 mm		CUT-OUT TO	873 mm		COMBUSTIBLE
					COMBUSTIBLE			MATERIALS
		mm COOKTOP CUT-OUT		64 mm
96 mm	127 mm				MATERIALS	COOKTOP CUT-OUT WIDTH		ABOVE COOKTOP
			DEPTH	min	(BOTH SIDES)
TERMINAL BOX						102 mm
Overall Dimensions						89 mm	E
						95 mm	254
			610 mm min	914 mm		min
							mm
				STANDARD
				FLOOR TO
				COUNTERTOP		914 mm OVEN OPENING
MODEL ICBCT36E				HEIGHT
Overall Width	914 mm
Overall Height	96 mm
Overall Depth	533 mm	*Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from
Minimum Cabinet Depth	578 mm	rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.
Minimum Height Clearance*	102 mm					873 mm
						COOKTOP CUT-OUT WIDTH
Cut-Out Width	873 mm	Countertop Cut-Out
Cut-Out Depth	489 mm

*Minimum 146 mm clearance is required			489 mm
between countertop and any combustible	64 mm		COOKTOP
			CUT-OUT DEPTH
surface directly below the cooktop.	min

For detailed terminal block dimensions, refer to the illustration on page 7.

FRONT OF COUNTERTOP

Dimensions may vary to ±3 mm.

10

I N S TA L L AT I O N I N S T RU C T I O N S

M U LT I P L E CO O K TO P

I N S TA LL AT I O N

If the framed electric cooktop is to be used with any combination of additional cooktop units or modules with a filler strip, the cut-out width is calculated by adding the corresponding units' cut-out dimensions plus 32 mm for each additional unit. Refer to the illustration below.

IMPORTANT NOTE: For Model ICBCT15E, the cut-out width should be increased from 340 mm to 356 mm when installed with multiple units.

IMPORTANT NOTE: Unframed electric cooktops Models ICBCT30EU and ICBCT36EU are not designed to be installed in combination with other cooktop units.

IMPORTANT NOTE: When multiple units are installed side by side, each unit must have its own separate recommended electrical circuit.

When two or more modules are installed together, an integrated module filler strip (IFILLER/S) is recommended. If a 762 mm downdraft ventilation system is also installed, an integrated module support for downdraft ventilation (ISUPPORT) is also required. Contact your Wolf dealer for information on these accessory components.

AC C E S S O R I E S

Optional accessories are available through your

Wolf dealer. To obtain local dealer information, visit our website, wolfappliance.com.

1518 mm – FOUR MODULES WIDTH OR

1511 mm – 762 mm COOKTOP AND TWO MODULES OR 1276 mm – 914 mm COOKTOP AND ONE MODULE

1130 mm – THREE MODULES WIDTH OR 1124 mm – 762 mm COOKTOP AND ONE MODULE

743 mm

TWO MODULES WIDTH

					356 mm
								489 mm
					CUT-OUT			CUT-OUT
64 mm					WIDTH			DEPTH
min

FRONT OF COUNTERTOP

Countertop cut-out dimensions for installation of multiple cooktops

11

WOLF E L E C T R I C CO O K TO P S

UNFRAMED M O D E L I C B C T 3 0 E U

The illustrations below provide installation specifications for Model ICBCT30EU.

For ease of installation, 838 mm cabinets are recommended for installation of Model ICBCT30EU.

A Wolf 762 mm built-in single oven may be installed below Model ICBCT30EU. For this installation, unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven. Refer to installation instructions provided with the built-in oven for additional specifications.

If Model ICBCT30EU is installed above cabinets, electrical placement is not critical. A grounded electrical box should be located within 1.2 m of the right rear of the cooktop.

For Model ICBCT30EU installation options, refer to Unframed Installations on pages 14–15.

IMPORTANT NOTE: For flush mount applications, it is recommended to measure the cooktop glass before cutting the countertop to ensure a proper fit. Small variances may exist between the template and the cooktop.

INSTALLATION SPECIFIC ATIONS – MODEL ICBCT30EU

533 mm

OVERALL

DEPTH

762 mm

OVERALL WIDTH

108 mm

140 mm

TERMINAL BOX

Overall Dimensions

MODEL ICBCT30EU

Overall Width

762 mm

Overall Height

108 mm

Overall Depth

533 mm

Minimum Cabinet Depth

578 mm

Minimum Height Clearance*

114 mm

Cut-Out Width

721 mm

Cut-Out Depth

492 mm

*Minimum 159 mm clearance is required between countertop and any combustible surface directly below the cooktop.

For detailed terminal block dimensions, refer to the illustration on page 7.

330 mm			838 mm RECOMMENDED
			CABINET WIDTH	762 mm
max	457 mm	51 mm*min	762 mm min	COUNTERTOP TO
		CUT-OUT TO		COMBUSTIBLE
SEE COUNTERTOP		COMBUSTIBLE	SEE COUNTERTOP	MATERIALS
CUT-OUT BELOW		MATERIALS	CUT-OUT BELOW	ABOVE COOKTOP
		(BOTH SIDES)
102 mm min			114 mm
			89 mm	E
610 mm min	914 mm		102 mm	254
			min	mm
	STANDARD		TO OVEN
	FLOOR TO		OPENING
	COUNTERTOP		762 mm OVEN OPENING
	HEIGHT

*Minimum clearance from both side edges and back edge of cooktop cut-out to combustible materials up to 457 mm above countertop.

765 mm**

Countertop Cut-Out RECESSED AREA FOR

FLUSH MOUNT INSTALLATION ONLY

RECESSED AREA FOR

33 mm

721 mm COOKTOP

FLUSH MOUNT INSTALLATION ONLY

RADIUS

CUT-OUT WIDTH

COUNTERTOP

51 mm*

22 mm

PROFILE

11 mm RADIUS

537 mm**

max

RECESSED AREA

492 mm

FOR FLUSH MOUNT

COOKTOP

INSTALLATION ONLY

CUT-OUT DEPTH

40 mm

8 mm

Dimensions may vary to ±3 mm.

	FRONT OF COUNTERTOP
**Minimum dimension, but may be exceeded by up to 3 mm.	62 mm

12

I N S TA L L AT I O N I N S T RU C T I O N S

UNFRAMED M O D E L I C B C T 3 6 E U

The illustrations below provide installation specifications for Model ICBCT36EU.

For ease of installation, 991 mm cabinets are recommended for installation of Model ICBCT36EU.

A Wolf 914 mm built-in single oven may be installed below Model ICBCT36EU. For this installation, unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven. Refer to installation instructions provided with the built-in oven for additional specifications.

If Model ICBCT36EU is installed above cabinets, electrical placement is not critical. A grounded electrical box should be located within 1.2 m of the right rear of the cooktop.

For Model ICBCT36EU installation options, refer to Unframed Installations on pages 14–15.

IMPORTANT NOTE: For flush mount applications, it is recommended to measure the cooktop glass before cutting the countertop to ensure a proper fit. Small variances may exist between the template and the cooktop.

INSTALLATION SPECIFIC ATIONS – MODEL ICBCT36EU
	533 mm
	OVERALL
	DEPTH
914 mm					991 mm
OVERALL WIDTH		330 mm					762 mm
					RECOMMENDED CABINET WIDTH
		max	457 mm	51 mm*min	914 mm min		COUNTERTOP TO
				CUT-OUT TO			COMBUSTIBLE
108 mm	140 mm	SEE COUNTERTOP		COMBUSTIBLE	SEE COUNTERTOP		MATERIALS
		CUT-OUT BELOW		MATERIALS	CUT-OUT BELOW		ABOVE COOKTOP
				(BOTH SIDES)
TERMINAL BOX		102 mm min			114 mm
Overall Dimensions					89 mm		E
					102 mm	254
		610 mm min	914 mm
					min
						mm
			STANDARD		TO OVEN
			FLOOR TO		OPENING
		COUNTERTOP			914 mm OVEN OPENING
MODEL ICBCT36EU			HEIGHT
Overall Width	914 mm
Overall Height	108 mm
Overall Depth	533 mm	*Minimum clearance from both side edges and back edge of cooktop cut-out to combustible materials up to 457 mm above countertop.
Minimum Cabinet Depth	578 mm				918 mm**
		Countertop Cut-Out
Minimum Height Clearance*	114 mm				RECESSED AREA FOR
					FLUSH MOUNT INSTALLATION ONLY
Cut-Out Width	873 mm	RECESSED AREA FOR		33 mm	873 mm
		FLUSH MOUNT INSTALLATION ONLY		RADIUS	COOKTOP CUT-OUT WIDTH
Cut-Out Depth	492 mm	COUNTERTOP					51 mm*
		PROFILE
*Minimum 159 mm clearance is required		22 mm		537 mm**	11 mm RADIUS
between countertop and any combustible		max		RECESSED AREA			492 mm
			FOR FLUSH MOUNT				COOKTOP
surface directly below the cooktop.
			INSTALLATION ONLY				CUT-OUT DEPTH
For detailed terminal block dimensions,		8 mm		40 mm
refer to the illustration on page 7.

Dimensions may vary to ±3 mm.

	FRONT OF COUNTERTOP
**Minimum dimension, but may be exceeded by up to 3 mm.	62 mm

13

WOLF E L E C T R I C CO O K TO P S

U N F R A M E D INSTALLATIONS

Flush mount installations are intended for granite, solid surface or stone countertop surfaces only. Failure to use high heat resistant surface will result in countertop damage if hot cooking utensils are accidentally moved off the cooking surface.

MODELS ICBCT30EU AND ICBCT36EU

Unframed electric cooktop Models ICBCT30EU and ICBCT36EU can be mounted flush with the top of the countertop or as a frameless installation with the glass mounted on top of the countertop surface.

IMPORTANT NOTE: The materials required for a flush mount installation are provided with the unframed Models ICBCT30EU and ICBCT36EU. Refer to the instructions provided with the unframed cooktop installation kit (#811358) for additional specifications.

FLUSH MOUNT INSTALLATION

There are two options for a flush mount installation of the unframed electric cooktop; Option 1 and Option 2.

OPTION 1: For this flush mount installation, a recessed area surrounding the standard countertop cut-out is required. Fabrication of the recessed area must take place before the final countertop installation. A template of the countertop cut-out is provided with the unframed cooktop for fabrication purposes.

IMPORTANT NOTE: This fabrication method is not recommended for molded backsplash style countertops (triple cove).

For countertop cut-out dimensions, refer to the Installation Specifications illustration on page 12 for Model ICBCT30EU and page 13 for Model ICBCT36EU.

In order to rout the required recessed area for this flush mount installation, a second template must be made from 13 mm plywood. The template will be used as a guide for a top bearing router bit.

Make the wood template wide enough so that clamps used to hold this template to the countertop do not interfere with the router base.

The cut-out dimension of the wood template should match the outer perimeter of the template supplied with the cooktop.

Center the wood template over the existing cut-out in the countertop and clamp. It may be helpful to use medium-strength double-sided tape to adhere the template to the countertop; this will keep the template from shifting during the routing operation. Make sure that the adhesive can be easily removed by testing it on a scrap piece of the countertop. Using a top bearing router bit with the wood template as a guide, rout out a 8 mm deep recessed area in the countertop cut-out.

14

I N S TA L L AT I O N I N S T RU C T I O N S

U N F R A M E D INSTALLATIONS

FLUSH MOUNT INSTALLATION

OPTION 2: For this flush mount installation, the countertop cut-out will be the same size as the outer edge of the glass top. It is recommended that cooktop itself be used as the template for the cut-out. Turn the cooktop over and mark the opening using the glass top as a template.

It will be necessary to attach L-shaped brackets or cleats to the inner perimeter of the cut-out to support the cooktop. The top edge of the bracket can be no wider than 22 mm and will be attached 8 mm below the surface of the countertop. Refer to the illustration below. Attachment of the brackets is up to the installer's discretion, wherever enough countertop material is present.

For additional support in the cut-out area, adhere scrap countertop material to the bottom side of the countertop. Consult your countertop supplier for the proper methods of attachment.

FRAMELESS INSTALLATION

Unframed electric cooktop Models ICBCT30EU and ICBCT36EU can be installed as a frameless application, with the glass mounted on top of the countertop surface. For countertop cut-out dimensions, refer to the Installation Specifications illustration on page 12 for Model ICBCT30EU and page 13 for Model ICBCT36EU.

8 mm	L-Shaped
	Brackets
22 mm

Flush mount installation brackets

15

WOLF E L E C T R I C CO O K TO P S

E L E C T R I C A L REQUIREMENTS

Verify that power is disconnected from the electrical box before proceeding.

REQUIRED POWER SUPPLY

Model ICBCT15E

220-240 V AC, 50/60 Hz

Models ICBCT30E and ICBCT30EU

220-240 V AC, 50/60 Hz

Models ICBCT36E and ICBCT36EU

220-240 V AC, 50/60 Hz

MAXIMUM CONNECTED LOAD

Model ICBCT15E

3.7 kW

Models ICBCT30E and ICBCT30EU

8.1 kW

Models ICBCT36E and ICBCT36EU

10.5 kW

This appliance must be installed in accordance with local codes. The correct voltage, frequency and amperage must be supplied to the appliance from a dedicated, grounded circuit which is protected by a properly sized circuit breaker or time delay fuse. The proper voltage, frequency and power ratings are listed on the product rating plate, located on the underside of the cooktop. Refer to the illustration on page 5 for location of the rating plate.

16

I N S TA L L AT I O N I N S T RU C T I O N S

E L E C T R I C A L R E Q U I R E M E N T S

A properly rated cord should be attached to the power supply of the electric cooktop as shown in the illustration below. Open the power box to expose the screws with corresponding numbers. Loosen the 1, 5, and ground screws. Run the cord through the circular hole and into the supply box. Attach the Neutral wire to the number 1 position. Attach the line wire to the number 5 position and attach the ground wire to the corresponding ground screw. After tightening the screws, tighten the cord strain relief then close the cover to the power supply box without pinching any of the wires.

The complete appliance must be properly grounded at all times when electrical power is applied.

Do not ground the appliance with the neutral (white) house supply wire. A separate ground wire must be utilized.

If aluminum house supply wiring is utilized, splice the appliance copper wire to the aluminum house wiring using special connectors designed and agency certified for joining copper and aluminum. Follow the connector manufacturer's recommended procedure carefully. Improper connection can result in a fire hazard!

I M P O RTA N T N OT E

This appliance must be installed in accordance with local codes.

N

L1

GROUND

Wiring diagram

17

WOLF E L E C T R I C CO O K TO P S

COOKTOP I N S TA L L AT I O N

Attach the foam strip to the underside of the cooktop frame. Refer to the illustration below.

IMPORTANT NOTE: For frameless installations, adhere the foam strip to the outer edge of the glass, not the support frame.

IMPORTANT NOTE: The materials required for a flush mount installation are provided with the unframed Models ICBCT30EU and ICBCT36EU. Refer to the instructions provided with the unframed cooktop installation kit (#811358).

Gently lower the unit into the cut-out area in the countertop and center. Check that the front edge of cooktop is parallel to the front edge of the countertop. Check that all required clearances are met.

Attach the brackets to the bottom of the unit, as shown in the illustration below. Install the clamping screws into the bracket and tighten until the screws contact the underside of the countertop. Do not overtighten the screws.

IMPORTANT NOTE: Do not seal the cooktop to the countertop. It must be removed if service is necessary.

If the ceramic glass top of the cooktop is broken, turn off power to the unit. Do not operate until glass has been replaced by a Wolf authorized service center.

COOKTOP

FOAM

STRIP

Foam strip

COOKTOP
	COUNTERTOP
BRACKET
BRACKET	102 mm
SCREWS	CLAMPING
	SCREW

Installation brackets

18

I N S TA L L AT I O N INSTRUCTIONS

BEFORE O P E R AT I N G THE COOKTOP

Clean the ceramic glass surface carefully using the Cooktop Cleaning Crème provided with the cooktop. Remove all cleaning residue.

Read the entire Wolf Electric Cooktops Use & Care Information included with the cooktop.

COOKTOP R E M O VA L

IMPORTANT NOTE: This procedure should only be performed by a Wolf authorized service center.

If it is necessary to remove the cooktop for cleaning or service, disconnect the electrical supply. Remove the mounting brackets on the right and left side of the unit and remove the cooktop. Reinstall in the reverse order.

IMPORTANT NOTE: For flush mount installations, use a razor blade to carefully cut around the RTV perimeter seal. A new RTV installation kit (#811358) will be required to reinstall the cooktop. This kit is available through your Wolf dealer. To obtain local dealer information, visit our website, wolfappliance.com.

ACCESSORIES

Optional accessories are available through your

Wolf dealer. To obtain local dealer information, visit our website, wolfappliance.com.

19

ACCESSORIES

Optional accessories are available through your

Wolf dealer. To obtain local dealer information, visit our website, wolfappliance.com.

WOLF E L E C T R I C CO O K TO P S

T R O U B L E SHOOTING

IF COOKTOP DOES NOT OPERATE

IMPORTANT NOTE: If the electric cooktop does not operate properly, follow these troubleshooting steps:

Verify that power is being supplied to the cooktop.

Check electrical connections to ensure that the installation has been completed correctly.

Follow troubleshooting procedures as described in the Wolf Electric Cooktops Use & Care Information.

If the cooktop still does not work, contact a Wolf authorized service center. Do not attempt to repair the cooktop yourself. Wolf is not responsible for service required to correct a faulty installation.

This cooktop must be repaired only by a Wolf authorized service center. The unit must be disconnected from power prior to service.

20

I N S TA L LAT I ON INSTRUCTIONS

IF YOU NEED S E RV I C E

If service is necessary, maintain the quality built into your electric cooktop by calling a Wolf authorized service center.

To obtain the name and number of a Wolf authorized service center, visit our website, wolfappliance.com.

When calling for service, you will need the cooktop model and serial numbers. Both numbers are listed on the rating plate, located on the underside of the cooktop. Refer to the illustration on page 5 for location of the rating plate.

The information and images in this book are the copyright property of Wolf Appliance, Inc., an affiliate of Sub-Zero, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Wolf Appliance, Inc., an affiliate of Sub-Zero, Inc.

©Wolf Appliance, Inc. all rights reserved.

CONTACT INFORMATION

Website:

wolfappliance.com

21

I N F O R M AC I Ó N

DE CONTACTO

Página Web: wolfappliance.com

Cuando consulte las instrucciones que aparecen

en esta guía, encontrará símbolos de ADVERTENCIA y PRECAUCIÓN. Esta información en recuadros es importante para instalar el equipo de Wolf de forma segura y eficaz. Existen dos tipos de posibles riesgos que pueden producirse durante una instalación.

indica una situación en la que se pueden sufrir heridas leves o provocar daños secundarios al producto si no se siguen las instrucciones.

indica peligro de que se produzcan heridas personales graves o incluso puede provocar la muerte si no se siguen las precauciones especificadas.

Otro tipo de anotación que es importante resaltar es la que se incluye en NOTA IMPORTANTE: En esta nota se resalta la información que resulta especialmente importante para que la instalación se realice sin problemas.

WOLF® es una marca comercial registrada de Wolf Appliance, Inc.

P LAC A S V I T R O C E R Á M I C A S D E WO L F

REQUISITOS DE I N S TA LAC I Ó N

A N T E S DE COMENZAR

NOTA IMPORTANTE: Guarde estas instrucciones de instalación para que el inspector local pueda utilizarlas.

Lea las instrucciones de instalación antes de llevar a cabo la instalación.

Esta instalación debe ser realizada por un técnico cualificado.

Instalador: guarde estas instrucciones para que el inspector local pueda utilizarlas como referencia y, a continuación, entréguelas al propietario del aparato.

Propietario: lea y guarde estas instrucciones para que pueda utilizarlas como referencia en el futuro y asegúrese de leer la guía de uso y mantenimiento antes de utilizar el aparato.

NOTA IMPORTANTE: Este aparato debe instalarse siguiendo las normativas nacionales correspondientes. Se debe aplicar al aparato el voltaje, la frecuencia y el amperaje adecuados desde una instalación eléctrica resistente con toma de tierra protegida por un fusible de retardo. El voltaje, la frecuencia y la potencia se muestran en la placa de datos del producto.

Apunte la referencia del modelo y el número de serie antes de instalar el aparato. Esta información se muestra en la placa de datos del producto situada en la parte inferior de la placa. Observe la siguiente ilustración.

Es responsabilidad del propietario asegurarse de que la instalación se realiza de manera correcta. Esta placa debe ser instalada por un técnico cualificado. Debe asegurarse de que la instalación eléctrica es la correcta y que cumple todos los códigos y normativas nacionales.

Las instalaciones y reparaciones deben ser realizadas por un contratista cualificado o autorizado o por un electricista cualificado o autorizado por el estado, provincia o región en la que se va a instalar este aparato.

Compruebe que tiene todo lo necesario para que la instalación se lleve a cabo de la manera correcta. Es responsabilidad del instalador dejar los espacios requeridos para la instalación que se especifican en este documento y en la placa de datos del producto. La placa de datos está ubicada en la parte inferior del aparato. Observe la siguiente ilustración.

Este aparato necesita una conexión a tierra; consulte la sección Requisitos eléctricos en la página 34.

Esta placa está diseñada para que se utilice en espacios interiores.

Ubicación de la placa de datos debajo

de la vitrocerámica

Ubicación de la placa de datos

INFORMACIÓN

DE LA PLACA

DE DATOS

Referencia del modelo

Número de serie

23

P LAC A S V I T R O C E R Á M I C A S D E WO L F

PREPARACIÓN DEL S I T I O

NOTA IMPORTANTE: La instalación de la placa vitrocerámica de Wolf debe cumplir los siguientes requisitos de colocación. Las medidas que se especifican son las mínimas para que el funcionamiento de la placa sea seguro. Observe la siguiente ilustración.

Para eliminar el riesgo de sufrir quemaduras o de que se produzca un incendio al alcanzar las superficies calientes, debe evitar colocar armarios por encima de los módulos de superficie. Si va a colocar armarios, el riesgo se puede reducir instalando una campana de extracción que sobresalga horizontalmente un mínimo de 127 mm de la parte inferior de los armarios.

C

G

D

E

B

F

A

B

Distancias mínimas de instalación

COLOC ACIÓN EN LA ENCIMERA

A)Superficie mínima de encimera plana. Debe ser igual o superior al ancho de la placa.

B)Espacio mínimo de 25 mm desde el borde lateral de la placa a cualquier superficie combustible situada 457 mm por encima de la placa (área sombreada de la ilustración).

MEDIDAS DE LOS ARMARIOS SUPERIORES

C)El espacio mínimo entre los armarios laterales superiores debe ser igual o superior al ancho nominal de la placa o placas.

D)Debe existir una distancia vertical mínima de 457 mm desde la encimera hasta la parte inferior

de los armarios laterales con una distancia lateral mínima.

E)La distancia vertical mínima entre la encimera y los materiales combustibles situados por encima de la placa debe ser de 762 mm.

F)Distancia mínima de 25 mm a la pared trasera.

G)El fondo máximo de los armarios superiores laterales situados por encima de la placa debe ser de 330 mm con una distancia lateral mínima.

Si no coloca la placa siguiendo las distancias de separación correctas, es posible que se produzca un incendio.

24

INSTRUCCIONES DE I N S TA L A C I Ó N

ESPECIFIC ACIONES DE LA

I N S TA L A C I Ó N

Las ilustraciones de las páginas 26–31 proporcionan las medidas totales, las especificaciones de la instalación y las medidas del corte de la encimera para cada uno de los modelos de placas vitrocerámicas de Wolf.

Esta placa está diseñada para que se adapte a un armario de base estándar de 610 mm de fondo con una encimera de 635 mm de fondo. Antes de cortar la encimera, compruebe que la placa va a quedar separada de las paredes laterales del armario inferior.

Se necesita dejar un espacio para el bloque de terminales y para los cables en la parte trasera derecha de la placa. Observe la siguiente ilustración para ver las medidas.

VITROCERÁMIC AS CON MARCO

Para los modelos con marco, debe dejar un espacio de 146 mm entre la encimera y cualquier superficie combustible por debajo de la placa.

Las vitrocerámicas con marco de Wolf están diseñadas para que se puedan instalar junto con otras placas.

NOTA IMPORTANTE: Cuando instale varias placas juntas, consulte las dimensiones de corte de la encimera en la página 29.

Las vitrocerámicas con marco de Wolf pueden instalarse con un sistema de ventilación de tiro ascendente de Wolf. Consulte las instrucciones de instalación que se proporcionan con el sistema

de ventilación de tiro ascendente para obtener más información.

VITROCERÁMIC AS SIN MARCO

Para los modelos sin marco, debe dejar un espacio de 159 mm entre la encimera y cualquier superficie combustible que haya debajo de la placa.

NOTA IMPORTANTE: Las vitrocerámicas sin marco de Wolf están diseñadas para que se puedan instalar junto con otras placas.

NOTA IMPORTANTE: Las vitrocerámicas sin marco no se pueden instalar con un sistema de ventilación de tiro ascendente.

Si desea consultar las opciones de instalación de las vitrocerámicas sin marco, consulte la sección Instalaciones sin marco en las páginas 32–33.

32 mm

56 mm

22 mm

84 mm

24 mm

Medidas del bloque de terminales

25

P LAC A S V I T R O C E R Á M I C A S D E WOLF

CON MARCO M O D E LO I C B C T 1 5 E

Las siguientes ilustraciones proporcionan las especificaciones de instalación del modelo ICBCT15E.

Si instala el modelo ICBCT15E encima de los armarios, la colocación de la toma eléctrica no es importante. Es necesario colocar una caja de conexiones a una distancia de 1,2 m de la parte trasera derecha de la placa.

Cuando instale la placa encima de un horno, a menos que vaya a utilizar armarios con un fondo superior a 610 mm, se recomienda que la toma eléctrica se coloque en un armario base situado a la derecha del horno.

NOTA IMPORTANTE: No bloquee el ventilador situado en la parte inferior de la placa.

ESPECIFIC ACIONES DE LA INSTALACIÓN – MODELO ICBCT15E

533 mm

FONDO

TOTAL

381 mm

ANCHURA TOTAL

96 mm

127 mm

CAJA PARA TERMINAL

Medidas totales

MODELO ICBCT15E

Anchura total

381 mm

Altura total

96 mm

Fondo total

533 mm

Fondo mínimo del armario

578 mm

Espacio mínimo de altura*

102 mm

Ancho del corte

340 mm

Fondo del corte

489 mm

*Se necesita dejar un espacio mínimo de altura de 146 mm entre la encimera y cualquier superficie combustible que se encuentre justo encima de la placa.

Si desea obtener las medidas detalladas del bloque de terminales, consulte la ilustración en la página 25.

Las medidas pueden variar ±3 mm.

				838 mm FONDO DEL ARMARIO
	330 mm			RECOMENDADO		762 mm
	máx	457 mm	51 mm*mín
						ENCIMERA A
	489 mm		CORTE A	340 mm		SUPERFICIE
51**			LOS MATERIALES	ANCHURA DE CORTE		INFLAMABLE
	FONDO DE CORTE
mm		64 mm	COMBUSTIBLES	DE LA PLACA		SOBRE LA PLACA
	DE LA PLACA
			(AMBOS LADOS)
		mín
					102 mm
				E	381
		914 mm
					mm
		ALTURA
		ESTÁNDAR
		DEL SUELO
		A LA ENCIMERA
				381 mm

NOTA: La aplicación que se muestra permite la instalación de dos módulos contiguos de 381 mm con un armario con una anchura recomendada de 838 mm. 457 mm de anchura de armario recomendada para la instalación de un solo módulo o superficie de cocción de 381 mm. *Espacio mínimo desde ambos bordes laterales del corte de la superficie de cocción hasta la superficie inflamable situada a 457 mm por encima de la encimera. **Espacio mínimo desde el borde trasero del corte de la superficie de cocción a la superficie inflamable situada a 457 mm sobre la encimera.

340 mm ANCHURA DE CORTE

DE LA PLACA

Corte de la encimera

489 mm FONDO DE CORTE

64 mm DE LA PLACA mín

PARTE DELANTERA DE LA ENCIMERA

26

INSTRUCCIONES DE I N S TA LAC I Ó N

CON MARCO M O D E LO I C B C T 3 0 E

Las siguientes ilustraciones proporcionan las especificaciones de instalación del modelo ICBCT30E.

Para que la instalación le resulte más sencilla, cuando instale el modelo ICBCT30E se recomienda utilizar armarios de 838 mm.

Se puede instalar un horno integrable sencillo de 914 mm ó 762 mm debajo del modelo ICBCT30E. Para esta instalación, a menos que vaya a utilizar armarios con un fondo superior a 610 mm, se recomienda que la toma eléctrica se coloque en un armario base situado a la derecha del horno.

Consulte las instrucciones de instalación que se proporcionan con el horno integrable para obtener más información.

Si instala el modelo ICBCT30E encima de los armarios, la colocación de la toma eléctrica no es importante. Es necesario colocar una caja de conexiones a una distancia de 1,2 m de la parte trasera derecha de la placa.

NOTA IMPORTANTE: No bloquee el ventilador situado en la parte inferior de la placa.

ESPECIFIC ACIONES DE LA INSTALACIÓN – MODELO ICBCT30E

533 mm

FONDO

TOTAL

762 mm

ANCHURA TOTAL

96 mm

127 mm

CAJA PARA TERMINAL

Medidas totales

MODELO ICBCT30E

Anchura total

762 mm

Altura total

96 mm

Fondo total

533 mm

Fondo mínimo del armario

578 mm

Espacio mínimo de altura*

102 mm

Ancho del corte

721 mm

Fondo del corte

489 mm

*Se necesita dejar un espacio mínimo de altura de 146 mm entre la encimera y cualquier superficie combustible que se encuentre justo encima de la placa.

Si desea obtener las medidas detalladas del bloque de terminales, consulte la ilustración en la página 25.

Las medidas pueden variar ±3 mm.

					838 mm FONDO DEL ARMARIO
		330 mm				RECOMENDADO	762 mm
		máx	457 mm	51 mm*min		762 mm mín
							ENCIMERA A
		489 mm		CORTE A			SUPERFICIE
	51**			LOS MATERIALES	721 mm ANCHURA DE CORTE		INFLAMABLE
		FONDO DE CORTE
	mm		64 mm	COMBUSTIBLES			SOBRE LA PLACA
						DE LA PLACA
		DE LA PLACA
				(AMBOS LADOS)
			mín
						102 mm
						89 mm	E
					95 mm	254
		610 mm mín			mín
			914 mm			mm
			ALTURA
			ESTÁNDAR
			DEL SUELO		762 mm CAVIDAD DEL HORNO
			A LA ENCIMERA

*Espacio mínimo desde ambos bordes laterales del corte de la superficie de cocción hasta la superficie inflamable situada a 457 mm por encima de la encimera. **Espacio mínimo desde el borde trasero del corte de la superficie de cocción a la superficie inflamable situada a 457 mm sobre la encimera.

721 mm

ANCHURA DE CORTE DE LA PLACA

Corte de la encimera

489 mm FONDO DE CORTE

64 mm DE LA PLACA mín

PARTE DELANTERA DE LA ENCIMERA

27

P LAC A S V I T R O C E R Á M I C A S D E WO L F

CON MARCO M O D E LO I C B C T 3 6 E

Las siguientes ilustraciones proporcionan las especificaciones de instalación del modelo ICBCT36E.

Para que la instalación le resulte más sencilla, cuando instale el modelo ICBCT36E se recomienda utilizar armarios de 991 mm.

Se puede instalar un horno integrable sencillo de 914 mm o 762 mm debajo del modelo ICBCT36E. Para esta instalación, a menos que vaya a utilizar armarios con un fondo superior a 610 mm, se recomienda que la toma eléctrica se coloque en un armario base situado a la derecha del horno.

Consulte las instrucciones de instalación que se proporcionan con el horno integrable para obtener más información.

Si instala el modelo ICBCT36E encima de los armarios, la colocación de la toma eléctrica no es importante. Es necesario colocar una caja de conexiones a una distancia de 1,2 m de la parte trasera derecha de la placa.

NOTA IMPORTANTE: No bloquee el ventilador situado en la parte inferior de la placa.

ESPECIFIC ACIONES DE LA INSTALACIÓN – MODELO ICBCT36E
	533 mm
	FONDO
	TOTAL
914 mm						991 mm
ANCHURA TOTAL
			330 mm			FONDO DEL ARMARIO RECOMENDADO		762 mm
			máx	457 mm	51 mm*mín	914 mm mín
								ENCIMERA A
			489 mm		CORTE A LOS			SUPERFICIE
		51**			MATERIALES	873 mm		INFLAMABLE
		mm	FONDO DE CORTE	64 mm	COMBUSTIBLES			SOBRE LA PLACA
96 mm						ANCHURA DE CORTE DE LA PLACA
	127 mm		DE LA PLACA		(AMBOS LADOS)
				mín
CAJA PARA TERMINAL						102 mm
Medidas totales						89 mm		E
						95 mm
							254
			610 mm mín	914 mm		mín
							mm
				ALTURA
				ESTÁNDAR
				DEL SUELO		914 mm CAVIDAD DEL HORNO
				A LA ENCIMERA
MODELO ICBCT36E
Anchura total	914 mm
Altura total	96 mm
Fondo total	533 mm	*Espacio mínimo desde ambos bordes laterales del corte de la superficie de cocción hasta la superficie inflamable situada a 457 mm por encima de la encimera.
		**Espacio mínimo desde el borde trasero del corte de la superficie de cocción a la superficie inflamable situada a 457 mm sobre la encimera.
Fondo mínimo del armario	578 mm
Espacio mínimo de altura*	102 mm					873 mm
						ANCHURA DE CORTE DE LA PLACA
Ancho del corte	873 mm	Corte de la encimera
Fondo del corte	489 mm

*Se necesita dejar un espacio mínimo de altura							489 mm
							FONDO DE CORTE
de 146 mm entre la encimera y cualquier super-
		64 mm					DE LA PLACA
ficie combustible que se encuentre justo encima		mín
de la placa.
Si desea obtener las medidas detalladas del
bloque de terminales, consulte la ilustración					PARTE DELANTERA DE LA ENCIMERA
en la página 25.

Las medidas pueden variar ±3 mm.

28

INSTRUCCIONES DE I N S TA L A C I Ó N

INSTALACIÓN DE OT R A S S U P E R F I C I E S

D E CO CC I Ó N

Si la vitrocerámica con marco se va a utilizar con otras combinaciones de módulos o unidades de cocción adicionales con un embellecedor, el ancho del corte se calcula sumando las medidas de corte de las unidades correspondientes más 32 mm por cada unidad adicional. Observe la siguiente ilustración.

NOTA IMPORTANTE: Para el modelo ICBCT15E, el ancho del corte debe aumentarse de 340 mm a 356 mm cuando se instale con varias unidades.

NOTA IMPORTANTE: Las vitrocerámicas sin marco modelo ICBCT30EU y ICBCT36EU están diseñadas para que se puedan instalar junto con otras placas.

NOTA IMPORTANTE: Cuando se instalen varias unidades juntas, cada unidad debe tener su propio circuito eléctrico recomendado.

Cuando se instalen dos o más módulos juntos, se recomienda utilizar un embellecedor de módulo integrado (IFILLER/S). Si además se instala un extractor de tiro ascendente de 762 mm, es necesario disponer de un soporte del módulo integrado para el extractor de tiro ascendente (ISUPPORT). Póngase en contacto con su distribuidor de Wolf para obtener información sobre estos accesorios.

ACCESORIOS

Podrá disponer de accesorios opcionales a través de su distribuidor de Wolf. Para obtener la información del distribuidor más cercano, visite nuestra página Web wolfappliance.com

	1518 mm – ANCHURA DE CUATRO MÓDULOS O
1511 mm – 762 mm SUPERFICIE DE COCCIÓN Y DOS MÓDULOS Ó
1276 mm – 914 mm SUPERFICIE DE COCCIÓN Y UN MÓDULO
1130 mm – ANCHURA DE TRES MÓDULOS Ó
1124 mm – 762 mm SUPERFICIE DE COCCIÓN Y UN MÓDULO
	743 mm
ANCHURA DE DOS MÓDULOS
356 mm	489 mm
ANCHURA	FONDO
DEL CORTE	DEL CORTE
64 mm
mín
PARTE DELANTERA DE LA ENCIMERA

Dimensiones de corte de la encimera para la instalación de otras superficies de cocción

29