Winegard SK-SWM3 User Manual

4.5 (2)

Installation Manual

Automatic

Multi-Satellite

TV Antenna

Model SK-SWM3

TRAV’LER® DIRECTV® SWM Slimline Antenna

www.winegard.com/mobile

For Technical Services, email help@winegard.com or call 1-800-788-4417 For Receivers and Programming, call 1-866-609-9374

For up-to-date information on receiver compatibility and programming, visit www.winegard.com/receivers

Product Registration

Please register your Winegard product by filling out and returning the Product Registration Card provided or by completing the online registration form at http://www.winegard.com/registration.

2452282

Winegard SK-SWM3 User Manual

Before Installing the Antenna

You have selected the Winegard® TRAV’LER® automatic multi-satellite TV antenna. The TRAV’LER antenna will deliver the ability to view multiple satellites at the same time with unmatched signal strength, the lowest travel height on

the market, maximum HD capabilities and easy to use functionality—just like you get at home. This manual provides important information on the installation and operation of your TRAV’LER antenna on an RV. Please take time to read the manual in its entirety before installing or operating your antenna.

Follow the instructions on this side of the manual if installing the TRAV’LER DIRECTV SWM Slimline antenna. For operation instructions, follow the instructions on the reverse side of the manual.

Specifications

Depending on location and receiver type, the following satellites can be accessed with the TRAV’LER DIRECTV SWM Slimline antenna during automatic operation: 99°, 101°, 103°.

Height of assembled unit: 9.75”

Width of mount base: 21”

Unit Weight: 53 pounds

Width of assembled unit: 34”

Length of mount base: 24”

Shipping Weight: 74 pounds

Length of assembled unit: 44”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

44

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

23.5

34

21

24

 

 

FIGURE 1. Dimensions of SK-SWM3

Safety Recommendations

Do not attempt to install this system in the rain or under any wet conditions. Moisture may affect electronics and void your warranty.

Do not paint this antenna. Painting the TRAV’LER antenna will void

your warranty. Pinch point (labeled)

Pinch point (labeled)

Pay attention to the pinch points as the antenna raises. The pinch points should be labeled on the antenna (see fig. 2).

Clearance Requirements

The arm of the TRAV’LER antenna extends 33” from the center of the base and may operate only 10” above the surface to which the TRAV’LER antenna is mounted. To ensure you have adequate clearance for the TRAV’LER antenna to safely operate, check that there are no obstructions taller than 10” within 33” of the center of the base.

Also, check that there are no obstructions (such as tree limbs) above the antenna that will prevent it from raising.

At its highest point, the antenna will extend to 37.5” above the roof to which it is mounted (see fig. 3).

FIGURE 3. Range of motion for TRAV’LER SWM antenna

Parts

Mount Base with 30’ Power/Control Cable

21V SWM Power Inserter

Splitter

Interface Box

 

 

 

 

Power Supply

 

 

 

Interface Box

 

 

Mounting Screw (20)

 

 

 

 

 

 

Reflector

24” AC power cord

30’ Gray Coax Cable

5/16” Reflector Nut (4)

 

 

 

Cable Entry Plate

 

 

 

 

 

5/16” Reflector Bolt (4)

 

 

1

2

Choosing a Location for the Antenna

1. For best performance and to reduce signal acquisition time, park the vehicle on a level surface that is free of obstructions such as trees or large buildings. Make sure you have a clear view of the southern sky.

2. Before removing the TRAV’LER antenna from its box, contact your RV dealer or manufacturer. Your RV may be prewired or have a reinforced area for this system.

3. Then, choose a location on the roof that meets the following requirements:

 

 

 

 

 

 

 

 

 

 

 

a. Offers enough support for a secure installation

 

 

 

 

r(

o

t

Y

t

 

 

b. Allows dish to raise and rotate without

 

 

 

 

N

 

e

A

 

 

 

 

 

o

 

 

 

 

 

 

 

 

 

 

 

 

 

t

 

 

 

 

t

 

 

 

 

 

 

t

interference from other roof-mounted equipment

 

 

e

 

 

 

 

 

 

c

 

 

l

c

 

 

 

 

 

 

a

 

 

 

 

 

 

 

 

 

 

h

 

 

f

 

 

 

 

 

 

 

e

 

R

e

 

 

 

 

 

 

 

 

d

 

 

 

 

 

 

 

 

 

 

)

c. Has a minimum roof space of 44” x 34” for

 

 

 

 

 

 

 

 

 

 

 

antenna (see fig. 4)

 

 

 

 

 

 

 

 

 

 

 

e

d

)

 

 

R

 

 

 

 

 

 

 

h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

e

 

 

 

 

 

 

 

 

 

 

Center of Base

f

 

 

 

 

 

 

c

 

 

 

l

 

 

 

 

 

ta

 

 

 

 

 

 

e

 

 

 

 

 

t

 

 

 

 

 

 

 

c

 

 

 

A

 

 

 

 

 

 

 

 

t

 

 

 

 

 

 

 

 

 

 

 

o

 

t

 

 

 

 

 

 

 

 

 

 

r

e

 

 

 

 

 

 

 

 

 

 

 

 

(NotY

 

 

 

 

 

 

 

 

44″

FIGURE 4. Required roof space for antenna

 

 

d. Lacks obstructions taller than 10” mounted within

 

 

a 33” radius from the center of the TRAV’LER base

34″

 

 

 

e. Has a gap of less than 3/16” between the bottom

 

 

of the antenna and the roof

 

 

Do not install the antenna in a

 

 

WARNING location where a gap of 3/16” or

 

 

more exists between the bottom of the antenna

 

 

and the roof, as the antenna may damage the roof

 

 

f. Is within 5 degrees of level, or the system may

 

 

require more time to locate satellites (for best

 

 

operation, must be within 3 degrees of level)

Choosing a Location for Cables to Enter the Vehicle

Once you have chosen a location for the TRAV’LER antenna, choose a location for the cables to enter the vehicle. Keep in mind the following:

1.The TRAV’LER interface box must plug into a well-ventilated 110 V outlet.

2.The 24” AC power cord must be long enough to extend from the outlet to the interface box power supply, which will then connect to the interface box.

3.The 30’ control cable must be long enough to extend from the mount base to the interface box.

4.The power inserter must be mounted inside the vehicle, but the splitter can be mounted on the roof of the vehicle (see Setup Option 1 & Setup Option 2 under “Overall Setup”).

5.Wires should not be run through the striped area (see fig. 5). Anything in the striped area will interfere with the operation of the TRAV’LER antenna and may cause damage to the object or to the antenna.

FIGURE 5. Marked area of antenna where cables should not be run

Make sure cables are long enough to reach their destination points inside the vehicle. For cable

CL-SK26

runs longer than 30’, an extension may be purchased. Winegard recommends using Model CL-SK26

 

25’ extension cable. Do not exceed 55’ of cable!

 

WARNING or injury caused by improper installation.

Sold Separately

Winegard is NOT liable for damage, expenses,

 

Installing the Antenna

1.Place the TRAV’LER antenna on the roof where you plan to install it. On the mount base, the transition plate is marked “FRONT” and “BACK.” Rotate the TRAV’LER antenna until the front of the mount base faces the front of the RV. The TRAV’LER antenna must be installed on or parallel to the centerline of the coach. See figure 6.

 

 

 

No obstructions

 

 

 

taller than 10″

 

 

 

in a 33″ radius

 

33″

Mount on or parallel to Centerline of RV

 

 

 

Front

 

Centerline of RV

 

RV of

 

 

 

FIGURE 6. Antenna (without reflector) installed parallel to centerline of RV

TIP When installing the antenna on a rubber roof, Winegard recommends using Model SKA-004 roller plate, which is designed to create a solid landing area for the roller. If not using this plate,

make sure that the roller does not come in contact with any rib supports or bubbles in the roof when in operation. Failure to do so may result in damage to the roof.

2. Verify that the marked “FRONT” of the transition plate is facing the front of the vehicle (see fig. 7).

“FRONT”

FIGURE 7. Marked “FRONT” of transition plate on fully assembled antenna

SKA-004

Sold Separately

3.Mark the location where the nine screw holes will go. It is important that you can see these marks on the roof of the RV. Then, move the mount base out of the installation area. It is recommended that you do not pre-drill the screw holes at this time.

4.To prevent water from getting into the mount base, use a solid line of approved sealant to connect the marks in the shape of the base. This step must be completed, or the unit will fail due to corrosion. Replace the TRAV’LER antenna base.

5.Before using the supplied mounting screws, check with your vehicle manufacturer for any special screw requirements. Then, screw the antenna base to the roof using nine mounting screws.

6.Run a solid bead of sealant around the edge where the transition plate meets the roof, making sure to cover each screw head. Be careful not to get any sealant above the transition plate.

3

4

Loading...
+ 5 hidden pages