2
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
EDI88130CS
ABSOLUTE MAXIMUM RATINGS
Parameter Unit
Voltage on any pin relative to Vss -0.2 to 7.0 V
Operating Temperature TA (Ambient)
Industrial -40 to +85 °C
Military -55 to +125 °C
Storage Temperature, Ceramic -65 to +150 °C
Power Dissipation 1.7 W
Output Current 40 mA
Junction Temperature, T
J 175 °C
RECOMMENDED OPERATING CONDITIONS
Parameter Symbol Min Typ Max Unit
Supply Voltage VCC 4.5 5.0 5.5 V
Supply Voltage VSS 000V
Input High Voltage VIH 2.2 — Vcc +0.5 V
Input Low Voltage V
IL -0.5 — +0.8 V
Parameter
Symbol
Condition
Max
Unit
LCC
Address Lines CI
V
IN
= Vcc or Vss, f = 1.0MHz
612pF
Data Lines C
O
V
OUT
= Vcc or Vss, f = 1.0MHz
814pF
These parameters are sampled, not 100% tested.
CAPACITANCE
(T
A = +25°C)
TRUTH TABLE
OE CS1 CS2 WE Mode Output Power
X H X X Standby High Z Icc
2, Icc3
X X L X Standby High Z Icc2, Icc3
H L H H Output Deselect High Z Icc1
L L H H Read Data Out Icc1
X L H L Write Data In Icc1
NOTE:
Stress greater than those listed under "Absolute Maximum Ratings" may cause
permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions greater than those indi-
cated in the operational sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect reliability.
Input Pulse Levels VSS to 3.0V
Input Rise and Fall Times 3ns
Input and Output Timing Levels 1.5V
Output Load Figure 1
NOTE: For t
EHQZ, tGHQZ and tWLQZ, CL = 5pF Figure 2)
30pF
480Ω
Vcc
Q
Figure 1 Figure 2
255Ω
5pF
480Ω
Vcc
Q
255
Ω
AC TEST CONDITIONS
Parameter Symbol Conditions Units
Min Typ Max
Input Leakage Current ILI VIN = 0V to VCC ——±5 µA
Output Leakage Current ILO VI/O = 0V to VCC ——±10 µA
(15-17ns) — 300 mA
Operating Power Supply Current ICC1 WE, CS1 = VIL, II/O = 0mA, CS2 = VIH (20ns) — 225 mA
(25-55ns) — 200 mA
Standby (TTL) Power Supply Current ICC2
CS1 ≥ VIH and/or CS2 ≤ VIL,
(17-55ns) — 25 mA
VIN ≥ VIH or ≤ VIL
(15ns) — 60 mA
CS1 ≥ VCC -0.2V and/or CS2 ≤ 0.2V
CS (17-55ns) — 3 10 mA
Full Standby Power Supply Current ICC3 CS (15ns) — — 15 mA
VIN ≥ Vcc -0.2V or VIN ≤ 0.2V LPS — — 5 mA
Output Low Voltage VOL IOL = 8.0mA — — 0.4 V
Output High Voltage V
OH IOH = -4.0mA 2.4 — — V
DC CHARACTERISTICS
(V
CC
= 5V, TA = -55°C to +125°C)
CSOJ,DIP,
Flatpack