Whirlpool GFG471LVB, GFG471LVQ, GFG471LVS, WFG371LVB, WFG371LVD Dimension Guide

®

30" (76.2 cm) Freestanding Gas Range

PRODUCT MODEL NUMBERS

PRODUCT DIMENSIONS

GFG471LV WFG381LV

WFG371LV

Gas supply: This range is design-certified by CSA International for use with Natural gas or, after proper conversion, for use with LP gas.

This range is factory set for use with Natural gas. The model/serial rating plate located behind the storage drawer on the right-hand side oven door frame has information on the types of gas that can be

used. If the types of gas listed do not include the type of gas A available, check with the local gas supplier.

Provide a gas supply line of 3/4" (1.9 cm) rigid pipe to the range

location. A smaller size pipe on longer runs may result in insufficient

gas supply. With LP gas, piping or tubing size can be 1/2" (1.3 cm)

C

minimum. Usually, LP gas suppliers determine the size and

F

B

materials used in the system.

NOTE: Pipe-joint compounds that resist the action of LP gas must

be used. Do not use TEFLON® tape.*

If local codes permit, a new CSA design-certified, 4 to 5 ft (122 to

152.4 cm) long, 1/2" (1.3 cm) or 3/4" (1.9 cm) I.D., flexible metal

appliance connector may be used for connecting range to the gas

supply line.

E

A 1/2" (1.3 cm) male pipe thread is needed for connection to the

female pipe threads of the inlet to the appliance pressure regulator.

The supply line must be equipped with a manual shutoff valve. This

D

valve should be located in the same room but external to the range.

It should be in a location that allows ease of opening and closing.

A. 27¹ ⁄" (69.9 cm) max. depth with handle

Electrical: 120-volt, 60-Hz, AC-only, 15-amp, fused electrical

B. 36" (91.4 cm) cooktop height (max.) with leveling

circuit is required. A separate circuit serving only this range is

legs screwed all the way in*

recommended. A time-delay fuse or circuit breaker is recommended.

C. 46⁄" (119.1 cm) overall height (max.) with

leveling legs screwed all the way in*

*TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

D. 29⁄" (75.9 cm) width

E. 25" (63.5 cm)

F. Model/serial rating plate (located on the oven

frame behind the top left side of the oven door)

*Range can be raised approximately 1" (2.5 cm) by adjusting the

CABINET OPENING DIMENSIONS

leveling legs.

Cabinet opening dimensions shown are for 25" (64.0 cm)

countertop depth, 24" (61.0 cm) base cabinet depth and

36" (91.4 cm) countertop height.

If the cabinet depth is greater than 24" (61.0 cm), oven frame

must extend beyond cabinet fronts by ½" (13.0 mm) minimum.

IMPORTANT: If installing a range hood or microwave hood

combination above the range, follow the range hood or

microwave hood combination installation instructions for

dimensional clearances above the cooktop surface.

A. 18" (45.7 cm) upper side cabinet to countertop

B. 13" (33 cm) max. upper cabinet depth

M

C. 30" (76.2 cm) min. opening width

D. For minimum clearance to top of cooktop, see NOTE*.

E. 30¹⁄ " (76.5 cm) min. opening width

F. This shaded area recommended for installation of rigid gas pipe.

G. 8" (20.3 cm)

H. Grounded outlet

I. 17" (43.2 cm)

J. 4¹⁄ " (11.4 cm)

K. 2" (5.1 cm)

L. 2" (5.1 cm) min. clearance from both sides of range to side wall

or other combustible material.

*NOTE: 24" (61.0 cm) minimum when bottom of wood or metal

cabinet is covered by not less than ¹⁄" (0.64 cm) flame retardant

millboard covered with not less than No. 28 MSG sheet steel,

0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or

0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the

cooking platform and the bottom of an uncovered wood or metal

cabinet.

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation	Ref. W10196160E
Instructions packed with product. Specifications subject to change without notice.	1/26/11