NWT0002D01
Use and Care
Guide ]
This use and care guide applies for the following models:
NWTOS02D, NWT2002Q, NWT2002D
Nominal Technical Specification I Madeby industries Acres Whirlpoo| S.A. de C.V.
Antigua Carreteraa Rome km 9
Nominal Current __ 6,0 A J CoL El Milagro
Frequency _ 60 Hz Apedacs N.L.
Voltage _ 110-127 V- M_xico, 66600
Phone.(01 81) 8329 2180
4. Before starting the refrigeration process allow the refrigerator to rest
from 2 to 3 hours in order to let the gas and oil be settled.
Connecting your refrigerator
A 110-127 V-, 60 Hz AC only 15 or 20 A fused and properly grounded
electrical supply is required.
Levellin
g screw
Te reduce the risk of fire, electrical shock, or injury when using
your refrigerator, follow these basic precautions:
• Read all instructions before using the refrigerator.
- Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still
dangerous ... even if they will "just sit in the garage a few days".
• if you are getting rid of your old refrigerator, do it safely.
• Never allow children to operate, play with, or crawl inside the refrigerator.
- Never clean refrigerator parts with gsmrnable fluids. The fumes can create a fire hazard or explosion.
• We suggest to remove the door or thigh it with a resistant cord.
• if supply cord is damaged must be replaced by our service department or a qualified person to avoid hazard.
•FOR YOUR SAFETY,
• Do not store or use gasoline or ether flammable vapors and liquids in the vicinity of this or any ether appliance.
The fumes can create a fire hazard or explosion.
• If damage in power supply cord occurs, it should be replaced by our service department or by an qualified
electrician in order to avoid a risk.
-SAVE THESE iNSTRUCTiONS-
Electrical shock hazard
The refrigerator must be properly grounded.
_¢ De not modify the electrical cord
Do net use an extension cord with this appliance, consult with a qualify technician
any doubts about the proper grounding of this appliance,
if your wail outlet is not proper one have a qualify technician install it.
if supply cord is damaged must be replaced by our service department or a
qualified person to avoid hazard.
Failure to follow these precautions may result in high risk of injury and even
death
• Do not use the refrigerator in an area where the room temperature will fall
below 13°C (55 ° F).
• Keep the refrigerator out of the weather.
• Connect the refrigerator only to the proper kind of outlet, with the correct
electrical supply and grounding.
• Do not load the refrigerator with food before it has time to get properly cold.
, Use the refrigerator only for the uses described in this manual.
• Properly maintain the refrigerator.
• Be sure the refrigerator is not used by anyone unable to operate it properly.
• The refrigerator is intended for domestic use.
Grounding Method
Your refrigerator has an electrical cord provided with 3 prong
grounding plug. To minimize the possibility of electrical shock,
the cord must be plugged into a mating 3 prong grounding type
wall outlet according to national electrical code and all local
codes, if plug will not fit the outlet, is your responsibility to have
a proper outlet installed by a qualified electrician.
Wall outlet for 3 prong plug cord,
grounded properly.
3 prong plug cord
Power supply Grounding
cord Terminal
Adjusting temperature control
Your refrigerator has 2 control knobs that let you independently set
the temperature in both, refrigerator and freezer compartments.
When you plug the refrigerator for the first time:
. Set the temperature control knob of refrigerator and freezer in f_.,_,,_
"MED" position, it means mid cool. Temperature ranges goes
from "MIN" or "-" (less cool) to "MAX" or "+" (coolest).
- If you set the temperature control knob to "APAGADO" (OFF) in
refrigerator compartment, the system turn off in both compartments.
but it still remains connected to power supply.
• Give the refrigerator time to cool down completely before adding .............
food. This could take several hours. Adjust the temperature control
to have food as cold as you like. The settings indicated above
should be correct for normal, household refrigerator usage.
Before connecting the new refrigerator follow these
steps:
1. Remove all packing material and the wood bases.
2. install your refrigerator under the following conditions:
* Allow 7,5 cm (3 inches) between overhead cabinets and
refrigerator top.
, Allow at least 5 cm (2 inches) between the refrigerator
condenser on the back and the wall.
, Allow 1,25 crn (1/2") on each side of the refrigerator for
ease of installation.
" If the hinge side of the refrigerator is to be against the
wall, you might want to leave extra space so the door can be opened wider.
3. Levelling the refrigerator
• Remove the wooden supports.
- To raise or lower the front of the refrigerator, turn each screw in a clockwise or
counterclockwise direction (figure 1).
• For greater levelling accuracy you should place a spirit level on the upper surface
of the refrigerator.
• it is recommended to incline lightly back the refrigerator
in order to let the door close by itself. ___ _-_'_"\ ii
Levellin
g screw
Raise Lower
:::t
1. Disconnect refrigerator from power supply. _- (_r_J
--t
2. Remove the bulb cover with a plain screwdriver. _
3. Replace with a 15 watt appliance bulb.
4. Replace the bulb cover.
5. Reconnect refrigerator to power supply.
NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to _ Ijreplace a bulb with one of the same size and shape.
; ;t C:: , ; v : C© ;
_t 2
This control helps you to reach longer periods of
conservation of fruit and vegetables, it controls the
amount of cool air inside crisper drawer. If your drawer
has a humidity control as shown in fig. 1, slide control
downward. If your drawer has a humidity control as
shown in fig. 2, she control from side to side. In beth
cases, this allow you to control the circulation of cool
air according to your needs. Fig. 1 Fg. 2
Loading...