Whirlpool AWP 045/3, AWP 044/3 INSTRUCTION FOR USE
CONTENTS GB
BEFORE USING THE APPLIANCE FOR THE FIRST TIME
• IMPORTANT: MAKE SURE YOU HAVE READ THE INSTALLATION INSTRUCTIONS.
• REMOVE THE TRANSIT BOLTS BEFORE USING THE MACHINE FOR THE FIRST TIME.
• First wash cycle without laundry:
Open the tap(s).
1.
Close the door.
2.
Pour a little detergent (about 100 ml) into the detergent compartment .
3.
Select a short wash programme (see prog ramme chart).
4.
Press the “ON/OFF” button.
5.
This will remove any water remaining in the machine from the manufacturer’s test run.
ROUTINE WASHES:
Open the tap(s).
1.
Sort the laundry according to fabric type and colour and load the machine.
2.
Close the door.
3.
Add detergent and any additives required.
4.
Select the programme, temperature and special options (depending on model).
5.
Press the “ON/OFF” button.
6.
3
GB QUICK REFERENCE GUIDE
INSTALLATION INSTRUCTIONS
APPLIANCE AND ACCESSORIES
PROTECTING THE ENVIRONMENT
SAFETY INSTRUCTIONS
MOVING AND TRANSPORTING THE APPLIANCE
SORTING THE WASH
DETERGENT AND ADDITIVES
DYEING AND BLEACHING
SELECTING THE PROGRAMME AND SPECIAL
OPTIONS / PROGRAMME START
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
5
10
11
11
11
12
13
14
15
DOOR LOCK / PROGRAMME END /
PROGRAMME RESELECTION
REMOVING THE FILTER / DRAINING
RESIDUAL WATER
CARE AND MAINTENANCE
TROUBLE-SHOOTING GUIDE
AFTER-SALES SERVICE
4
PAGE
PAGE
PAGE
PAGE
PAGE
16
16
17
18
18
INSTALLATION INSTRUCTIONS
TRANSIT BOLTS
The appliance is fitted with transit bolts to
prevent internal damage while it is being moved .
Before using the appliance the transit bolts
MUST be removed (Fig. 1).
Slacken the bolts with the spanner
1.
supplied (Fig. 2).
Move the bolt to the centre of the hole.
2.
Completely extract the bolt and the coloured
3.
plastic spacer.
Plug the hole using the plastic cap
4.
provided (Fig.3).
Repeat the above operations for the
5.
other 3 bolts.
Note
Fit the transit bolts before transporting the
appliance as follows:
Pry up the plastic caps with a screwdriver,
1.
slide them out against the direction indicated
with the arrow and remove them.
Fit the transit bolts by following the above
2.
procedure in reverse order.
Fig. 1
Fig. 2
Fig. 3
5
INSTALLATION INSTRUCTIONS
INSTALLATION
Install the appliance on a solid and level floor
•
surface, preferably in a corner of the room.
Make sure that all four feet are resting firmly
•
on the floor and check that the appliance is
perfectly level (use a spirit level).
If the floor is uneven, adjust the levelling feet
•
as required (do not insert pieces of wood,
cardboard etc. under the feet).
Slacken the locknut using the spanner supplied.
1.
Adjust the height of the foot, turning it by hand .
2.
Tighten the locknut anticlockwise towards
3.
the washing machine.
If the appliance is to be installed on a wooden
•
floor, distribute the weight by placing it on a
60x60 cm sheet of plywood at least 3 cm in
thickness. Secure the plywood sheet to the
floor.
1
3
2
BUILD-UNDER / WORKTOP
The appliance must be installed only under
a fitted, continuous kitchen worktop.
The appliance must only be built under using the
built under set UBS.
Unplug the appliance from the mains.
•
Unscrew the worktop fixing screws from
1.
the rear of the appliance.
Slide the worktop fully backward and lift it
2.
upwards to remove.
Install the cover panel following the relative
instructions.
Refit the fixing screws and tighten them.
3.
BUILD-UNDER OPENING DIMENSIONS
Width 600 mm
Height 825 mm
Depth 600 mm
WARNING:
Only plug the machine into the mains power
socket after you have fitted the cover panel
or the machine worktop.
1
2
3
6
INSTALLATION INSTRUCTIONS
WATER SUPPLY
Water supply: only cold water.
•
Tap: 3/4” threaded hose connector.
•
Water pressure (mains pressure):
•
10-100 N/cm2 (100 kPa-1000 kPa).
For Great Britain and Ireland only
Water inlet: hot and cold fill. The warm water
•
inlet temperature must not exceed 60°C.
INLET HOSE(S)
: If the inlet hose is already fitted to the rear
Note
panel on the appliance, ignore points 1 and 4.
Remove the inlet hose from the drum.
1.
Fit the mesh filter supplied in the thread
2.
between the straight end of the inlet hose(s)
and the tap(s).
Carefully screw the straight end of the inlet
3.
hose(s) to the tap(s) by hand.
Screw the curved end of the hose to the
4.
appliance taking care that the hose is not
kinked.
Turn the tap(s) on fully and check that the
5.
joints at the washing machine and the tap(s)
are watertight.
If the hose is not long enough, replace it with
•
a suitable length of pressure-resistant hose
(approved under EN 500 65 to withstand a
minimum of 10 bar).
Check the hose regularly for brittleness and
•
cracks and replace if necessary.
The washing machine may be connected
•
without a non-return valve.
Observe any special local regulations
•
regarding connection to the water supply.
7
Loading...