Whirlpool AWO/D 9614 Instructions For Use Manual

Whirlpool Switzerl and, www.whirlpool.ch

Bauknecht AG, Industriestrasse 36, 5600 Lenzburg, www.bauknecht.ch

Verkauf Telefon [phone] Fax [phone] [e-mail]
Kundendienst Telefon [phone] Fax [phone] [e-mail]
Ersatzteile Telefon [phone] Fax [phone] [e-mail]

Instructions for use

AWO/D 9614

GB PROGRAMME CHART

5019 301 06076

Whirlpool is a registered trademark of Whirlpool USA

❉

: optional / Yes : dosing required

1)

For improved garment care, spin speed is restricted in these programmes.

2)

Do not use liquid detergent when activating the “Start Delay”.

3)

Do not use liquid detergent for the main wash when activating the “Prewash” option.

The wool and handwash cycles of this machine have been tested and approved by The Woolmark Company
for the washing of Woolmark garments labelled as “machine wash” or “hand wash” pr ovided that the garments
are washed according to the instructions on the garment label and those issued in this programme chart.

M0620

Programme

Tem p e-

rature

Care

Labels

Max

Load

kg

Type of wash/Notes

- For temperature selection, respect the manufacturer’s
recommendations on the care label

Detergents and additives Special options Start

delay

Spin

Pre­wash

Main

Wash

Softe-

ner

Eco Easy

ironing

Pre-

wash

Intensive

rinse

Rinse

hold

Variable

spin

Max
Spin

Speed

rpm

White Cotton /

Antibacterial

95 °C

6.0

Normally to heavily soiled bed linen, table linen and
underwear, towels, shirts etc. made of cotton and linen.
At a temperature of 95°C, this programme eliminates
bacteria, ensuring sanitization of your laundry. The bacteria
removal efficiency has been tested following a similar
methodology to the NF EN 13697 standard of Nov. 2001.

❉

Yes

3)

❉❉ ❉❉❉❉

❉

2)

❉

max.

Cotton

60 °C

6.0

20 - 40 °C

5.0

Synthetics

20 - 60 °C

2.5

Normally soiled blouses, shirts, overalls etc. made of
polyester (Diolen, Trevira), polyamide (Perlon, Nylon) or
blends with cotton.

❉

Yes

3)

❉❉ ❉❉❉❉

❉

2)

❉

1000

1)

Daily load

20 - 60 °C

3.0

Slightly to normally soiled textiles made of cotton and/or
synthetics.

—

Yes

❉

—

❉

—

❉❉

❉

2)

❉

max.

Quick wash

20 - 30 °C

3.0

Shortly worn outer clothing made of cotton, polyester,
polyamide and blends with cotton.

—

Yes

❉

————

❉

❉

2)

❉

max.

Delicates

20 - 40 °C

1.5

Curtains and delicate clothing, dresses skirts, shirts and
blouses.

❉

Yes

3)

❉

——

❉

—

❉

❉

2)

❉

1000

1)

Wool

20 - 40 °C

1.0

Only woollens, labelled with the Woolmark and identified as
machine washable.
This programme (40°C) is tested and approved by The
Woolmark Company for machine washable wool.

—

Yes

❉

————

❉

❉

2)

❉

1000

1)

Handwash

20 - 40 °C

1.0

Textiles made of silk, linen, wool and viscose marked as
“handwashable”.
This programme (40°C) is tested and approved by The
Woolmark Company for handwashable wool.

—

Yes

❉

————

❉

❉

2)

❉

400

1)

Gentle Spin

——

1.0

In this programme spinning is gentle. Same as the spin cycle in
the “Wool” programme.

————————

❉❉

1000

1)

Spin

——

6.0

In this programme spinning is intensive. Same as the spin cycle
in the “Cotton” programme.

————————

❉❉

max.

Rinse & Spin

——

6.0

Same as the last rinse and the final spin in the “Cotton”
programme.

——

❉

———

❉❉❉❉

max.

Drain

———

Drain only - no spinning. Alternative method of terminating
programme after “Rinse Hold”. Press “Drain/Reset” and then
“Start/Pause” to start the programme.

———————————

A. “On/Off” button
B. Programme selection buttons
C. Option buttons
D. “Favourite” button
E. “Temperature” button
F. “Start delay” button
G. “Variable spin” button
H. “Start/Pause” button
I. “Drain/Reset” button
J. Display

K. Programme sequence indication

L. “Door open” indication
Your washing machine is equipped with

automatic safety functions which detect
and diagnose faults at an early stage
and react appropriately, e.g.:

M. “Water tap closed” indication
N. “Clean pump” indication
O. “Service” indication

N

H

M

I

A

L

O

J

B

}

C

D E F G

K

30106076GB.fm Page 1 Friday, July 13, 2007 6:44 PM

Black process 45.0° 100.0 LPI

5019 301 06076

Whirlpool is a registered trademark of Whirlpool USA

Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives”
in your Instructions for Use.

1. Push the

“On/Off”

button . The blue light

circle signals that the washer is switched on.

2. Select the

desired programme

by pushing the
corresponding programme button; it is marked
by a blue light.

3. The

temperature

and

spin speed

indicated on
the display can be altered by pressing the
“Temperature” button or the “Variable
spin” button .

When the combination of programme and
additional option(s) is not possible, the indication
lights switch off automatically. Unsuitable
combinations of options are deselected
automatically.

“Eco” button

• With a modified temperature profile and a
slightly prolonged washing duration, the
optimum combination of excellent washing
result and even lower energy consumption is
achieved.

“Easy ironing” button

• Can be used together with “Cotton”,
“Synthetics” and “Daily load” programmes to
make ironing easier.

• Increases the water quantity and the clothes are
spun very gently.

“Prewash” button

• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time
by approximately 15 min.

• Do not use liquid detergent for the main wash
when activating the Prewash option.

“Intensive rinse” button

• More water is added and rinse cycle is
prolonged.

• This option is particularly suitable for areas with
very soft water or for washing baby linen, and
helps people with allergies.

“Rinse hold” button

• The laundry remains in the last rinse water
without progressing to the final spin cycle to avoid
creasing and prevent colours from changing.

• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and
“Delicates”.

• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain
only.

• If you select “Rinse hold”, do not leave the
laundry to soak for too long.

Note:

The programme stops to “Rinse hold” at
the time the “Rinse hold” symbol on the
display lights up. The blue light under the

“Start/Pause”

button flashes.

Terminate the “Rinse hold” option :

• Press the

“Start/Pause”

button ; the
programme will terminate automatically with the
final spin cycle for the present wash programme.

• If you do not wish to spin the clothes, push

“Drain/Reset”

and then start the Drain

programme by pushing the

“Start/Pause”

button .

CONSUMPTION DATA

Programme

Tem pe r at ur e

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme Duration

(hours : minutes)

*

Cotton / Antibacterial 95 6.0 59**1.90 2:00

Cotton 60 6.0 56 1.14 2:10

Cotton with “Eco”

***

60 6.0 51 1.02 2:20

Cotton 40 5.0 56 0.70 2:00
Synthetics 60 2.5 50**0.80 1:35
Synthetics 40 2.5 46 0.50 1:20
Daily load 40 3.0 41 0.50 1:00

Quick wash 30 3.0 41 0.40 0:30

Delicates 30 1.5 60 0.50 0:45

Wool 40 1.0 60 0.50 0:45

Handwash 40 1.0 45 0.50 0:40

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

*

The time indicated on the display can deviate from the values in the table, because it takes into account the household conditions
applicable at that time.

**

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

***

Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

“Variable spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.

If there is a programme setting which you use
frequently, the appliance offers the possibility to
save one setting for each programme so that it can
be used again by just pushing one button.

• Select the desired programme, temperature,
spin speed and option(s), push and hold the

“Favourites”

button for at least 3 seconds.

The lamp next to

“Favourites”

shortly flashes
and then lights up - the programme setting is
saved.

Next time you want to use your individual
programme setting, select the programme, push the

“Favourites”

button and start by pushing

“Start/Pause”

.

If you want to replace the saved programme
setting by another one:

• Push the programme button, select temperature,
spin speed and options as desired and then press
and hold the

“Favourites”

button for at least
3 seconds. The previously saved programme
setting will be replaced by the new one.

The “Start Delay” allows to run the machine at
the consumer’s convenience, for example at night
when electricity is cheaper.

• Select programme, temperature, spin speed and
options.

• Press the “Start Delay” button to select a delay
time of 1, 3, 6, 9 or 12 hours.

• Press the

“Start/Pause”

button .
The countdown of the delay time begins; the
clock symbol on the display and the delay time
selected flash.

• The delay time and the clock symbol disappear
when the programme starts.

• The number of hours preselected can be reduced
by pressing again the “Start Delay” button.

To cancel the “Start Delay”

• Select another programme or press the

“Drain/Reset”

button .

Open the tap and press the

“Start/Pause”

button . The blue light under the

“Start/

Pause”

button

is on. The programme sequence
indicator shows the current programme phase,
running from top to bottom through Wash, Rinse,
Spin/Drain.

Before starting and after end of a programme, the
lamp lights to show that the door can be opened. As
long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel
(Reset) a running programme before the end”.

“Water tap closed”

The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the “Troubleshooting Guide” in the
Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).

“Service”

Lighting up of the “Service” indication can be caused by
a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your Instructions for Use;
if the fault persists, contact our After Sales Service.

• The light of the programme sequence indicator
is off, and the “Door open” indication lights
up.

1. Switch the machine off by pushing

“On/

Off”

.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

1. Press the

“Start/Pause”

button to pause

the programme. The light flashes.

2. Select the new programme, temperature, any
options and another spin speed if you want.

3. Press the

“Start/Pause”

button again. The
new programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.

The

“Drain/Reset”

button cancels a

programme before the end.

• Press the

“Drain/Reset”

button for at
least 3 seconds. Any existing water is drained
out before the door can be opened.

SAVE YOUR F AVOURITE PROGRAMMES

START DELAY

PROGRAMME START

“DOOR OPEN” INDICATION

RED INDICATIONS

PROGRAMME END

CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START

CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END

30106076GB.fm Page 2 Friday, July 13, 2007 6:44 PM

Black process 45.0° 100.0 LPI

.

CONTENTS

BEFORE USING THE WASHING MACHINE
PRECAUTIONS AND GENERAL

RECOMMENDATIONS
DESCRIPTION OF THE WASHING MACHINE
DOOR
CHILD SAFETY
BEFORE THE FIRST WASH CYCLE
PREPARATION OF THE WASHING
DETERGENTS AND ADDITIVES
REMOVING THE FILTER/DRAINING

RESIDUAL WATER
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
ACCESSORIES
TRANSPORT/HANDLING
ELECTRICAL CONNECTION

BEFORE USING THE WASHING MACHINE

Use only new hoses to connect the washing

1.Removing the packaging and inspection

After unpacking, make sure that the washing

•

machine is undamaged. If in doubt, do not use the
washing machine. Contact After-Sales Service or
your local retailer.

Check that the accessories and supplied parts are

•

all present.
Keep the packaging materials (plastic bags,

•

polystyrene parts, etc.) out of reach of children,
as they are potentially dangerous.

If the appliance was exposed to the cold prior to

•

delivery, keep it at room temperature for a few
hours before operating.

2.Remove the transport bolts

The washing machine is fitted with transport

•

bolts to avoid any possible damage to the interior
during transport. Before using the machine, it is
imperative that the transport bolts are removed.

After their removal, cover the openings with the

•

4 enclosed plastic caps.

3.Install the washing machine

Remove the protective film from the control panel

•

(if available on your model).
Move the appliance without lifting it by the worktop.

•

Install the appliance on a solid and level floor

•

surface, preferably in a corner of the room.
Make sure that all four feet are stable and resting

•

on the floor and then check that the washing
machine is perfectly level (use a spirit level).

In case of wooden or so-called “floating floors”

•

(for instance certain parquet or laminate floors),
place the appliance on a 60 x 60 cm sheet of
plywood at least 3 cm in thickness which is
secured to the floor.

4.Water inlet

Connect the water supply inlet hose in

•

accordance with the regulations of your local
water company.

Water inlet: Cold water only

•

(if no other information on
your programme chart)

Water tap: 3/4” threaded hose

•

connector

Water pressure

•

(flow pressure): 100-1000 kPa (1-10 bar).

•

machine to the water supply. Used hoses must
not be used and should be discarded.

5.Drain

Connect the drain hose to the siphon or hook it

•

over the edge of a sink by means of the “U” bend
supplied.

If the washing machine is connected to an

•

integrated drainage system, ensure the latter is
equipped with a vent to avoid simultaneous
loading and draining of water (siphoning effect).

6.Electrical connection

Electrical connections must be carried out by a

•

qualified technician in compliance with the
manufacturer’s instructions and current standard
safety regulations.

Data regarding voltage, power consumption and

•

protection requirements is given on the inside of
the door.

The appliance must be connected to the mains by

•

means of a socket with an earth connection in
accordance with current regulations. The
washing machine must be earthed by law. The
manufacturer declines all liability for damage to
property or injury to persons or animals, deriving
directly or indirectly from failure to observe the
directions.

Do not use extension leads or multiple sockets.

•

Before any maintenance on the washing machine

•

disconnect it from the mains supply.
After installation, access to the mains plug or to

•

disconnection from mains supply must be
ensured at all times via a double-pole switch.

Do not operate the washing machine if it has

•

been damaged during transport. Inform the
After-Sales Service.

Mains cable replacement is only to be carried out

•

by After-Sales Service.
The appliance must only be used in the

•

household for the prescribed uses.

Minimum housing dimensions:

Width: 600 mm
Height: 850 mm
Depth: 600 mm

GB 2