Whirlpool AWO 5105 INSTRUCTION FOR USE
30105861GB.fm Page 1 Wednesday, April 26, 2006 11:41 AM
GB AWO 5105 PROGRAMME CHART
A. “Door open” indication
This washing machine is equipped with
automatic safety functions which
detect and diagnose faults at an early
stage and react appropriately, e.g.:
B. “Service” indication
C. “Water tap closed” indication
D. “Clean pump” indication
Programme
Cotton
40 - 60 - 95 °C
Koch-Buntwäsche
40 - 60 - 95 °C
Care
Labels
- for temperature selection, respect the manufacturer’s
recommendations on the care label
Normally to heavily soiled bed linen, table linen and underwear,
towels, shirts etc. made of cotton and linen.
With heavily soiled laundry the additional “Prewash” option can be
selected as well.
C
D
Type of wash/Notes
H
J
E
F
E. Programme selector
F. “Start/Pause” button
G. Spin speed selector
A
H. Programme sequence indicator
B
and Start delay indicators
I
I. “Reset” button
J. “Start delay” button
G
Max
Detergents and additives Special options
Load
Pre-
Main
kg
5.0
wash
❉
Wash
Yes
Softener Start
delay
Start-
vorwahl
❉❉❉❉❉❉ ❉
Pre-
wash
Vor-
wäsche
Eco Intensive
Öko Intensiv
rinse
Spülen
Easy
ironing
Leicht
Bügeln
Variable
spin
Schleudern
Max
Spin
Speed
rpm
1000
Synthetics
30 - 40 - 60 °C
Delicates
30 - 40 °C
Daily load
40 °C
Quick wash
30 °C
Wool
Cold - 40 °C
Handwash
30 - 40 °C
Rinse & Spin Spülen & Schleudern —
Spin Schleudern —
Gentle Spin Schonschleudern —
Drain Abpumpen —
❉
: optional / Yes : dosing required
1)
For improved garment care, spin speed is restricted to 400 rpm in this programme.
Pflegeleicht
30 - 40 - 60 °C
Feinwäsche
30 - 40 °C
Mischwäsche
40 °C
Schnelle Wäsche
30 °C
Wolle
kalt - 40 °C
Handwäsche
30 - 40 °C
Normally soiled blouses, shirts, overalls etc. made of polyester
(Diolen, Trevira), polyamide (Perlon, Nylon) or blends with cotton.
Curtains and delicate clothing, dresses skirts, shirts and blouses.
Slightly to normally soiled textiles made of cotton and/or synthetics.
Shortly worn outer clothing made of cotton, polyester, polyamide and
blends with cotton.
Only woollens with a felt-free finish, labelled with the woolmark and
identified as machine washable.
Textiles made of linen, silk, wool and viscose marked as
“handwashable”.
Same as the last rinse and the final spin in the “Cotton” programme.
In this programme spinning is intensive. Same as the spin cycle in the
“Cotton” programme.
In this programme spinning is gentle. Same as the spin cycle in the “Wool”
programme.
Water is drained only without any spinning.
2.5
1.5
3.0 — Yes
3.0 — Yes
1.0 — Yes
1.0 — Yes
5.0 — —
5.0 — — —
1.0 — — —
—— — — — — — — — — —
Yes
❉
Yes
❉
❉❉❉❉❉❉ ❉
❉❉❉
❉❉
❉❉
❉❉
❉❉
❉❉
❉
❉
———
——
——
—— — —
—— — —
——
—— — —
—— — —
❉❉ ❉
—
❉
Whirlpool is a registered trademark of Whirlpool USA
—
—
❉
❉
❉
❉
❉
❉
❉
1000
1000
1000
1000
1000
400
1000
1000
1000
1)
5019 301 05861
Black process 45.0° 100.0 LPI
30105861GB.fm Page 2 Wednesday, April 26, 2006 11:41 AM
CONSUMPTION DATA
Temperature
Programme
(°C)
Cotton 95 5.0 54
Load
(kg)
Water
(l)
**
Energy
Approx. Programme
Duration
(kWh)
(hours : minutes)
1.90 2:00
*
Cotton 60 5.0 49 1.05 2:10
Cotton with “Eco”
***
60 5.0 49 0.95 2:20
Cotton 40 5.0 49 0.60 2:00
Synthetics 60 2.5 50
**
0.70 1:30
Synthetics 40 2.5 45 0.55 1:15
Delicates 30 1.5 50 0.50 0:45
Daily load 40 3.0 45 0.45 1:00
Quick wash 30 3.0 40 0.40 0:30
Wool 40 1.0 55 0.60 0:45
Handwash 40 1.0 45 0.60 0:40
Handwash 30 1.0 45 0.50 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data
in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load
and the type of wash.
The remaining time indicator can deviate from the values in the table, because it takes into account the household
*
conditions applicable at that time.
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains
**
the water out.
Reference Programme for Energy Label.
***
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives”
in your Instructions for Use.
Close the door and turn the programme selector to
the desired programme and temperature. The
indication lamp next to the
“Start/Pause”
button
flashes.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the
respective indication lights up.
When the combination of programme and
additional option(s) is not possible, the indication
lights switch off automatically. Unsuitable
combinations of options are deselected
automatically.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time
by approximately 15 min.
“Eco” button
• With a modified temperature profile and a
slightly prolonged washing duration, the
optimum combination of excellent washing
result and even lower energy consumption is
achieved.
“Intensive rinse” button
• More water is added and rinse cycle is
prolonged.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
“Easy ironing” button
• Can be used together with “Cotton”,
“Synthetics” and “Daily load” programmes to
make ironing easier.
• Increases the water quantity and the clothes are
spun very gently.
“Variable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is se lected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
START DELAY
The “Start Delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper.
• Select programme, temperature and options.
• Press the “Start Delay” button to select the
delay time by 1, 3, 6, 9 or 12 hours.
• Press the
“Start/Pause”
button.
The indication next to the “Start Delay” button
lights up and goes off when the programme
starts.
• Once having pressed the
“Start/Pause”
button,
the countdown of the time delay begins. When
the programme starts, the start delay indicator
light goes off and is replaced by the programme
sequence indication.
• After the
“Start/Pause”
button has been
pressed, the number of hours preselected can
be reduced by pressing again the “Start Delay”
button.
To cancel the “Start Delay”
..before you press the “Start/Pause” button:
• Turn the programme selector to another
position or press the
“Reset”
button.
..after having pressed the “Start/Pause”
button:
• Press the “Reset” button for at least 3 seconds the start delay indicator light goes out.
PROGR AMME S TART
Open the tap and press the
“Start/Pause”
The indication lamp next to the
“Start/Pause”
button.
button lights up. The programme sequence
indicator shows the current programme phase,
running from left to right through Wash, Rinse, Spin/
Drain.
When the programme phase is finished, the
corresponding indication goes out.
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the
lamp lights to show that the door can be opened. As
long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel
(Reset) a running programme before the end”.
RED INDICATIONS
“Service”
Lighting up of the “Service” indication can be caused
by a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your Instructions for
Use; if the fault persists, contact our After Sales
Service.
“Water tap closed”
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the “Troubleshooting Guide” in the
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
PROGRAMME END
• All the lights of the programme sequence
indicator are off, and the “Door open”
indication lights up.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the
“Start/Pause”
button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the
“Start/Pause”
button again. The
new programme continues at the same position
where the previous programme was
interrupted. Do not add detergent for this
programme.
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
The
“Reset”
button cancels a programme before
the end.
• Press the
“Reset”
button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
Whirlpool is a registered trademark of Whirlpool USA
5019 301 05861
Black process 45.0° 100.0 LPI
Loading...