Whirlpool ADP 952 WHM Service Manual
SERVICE
Model ADP 952 WHM
Version 8542 952 61010 Page
Whirlpool Europe
Customer Services
ADP 952 WHM
Service Manual
Dishwasher
ADP 952 WHM
Technical data 2 - 4
Spare part list 5 - 6
Exploded view 7 - 8
Circuit diagram 9
Program diagram 10
Text/Legend 11 - 19
Family B5
This documentation is only intended for qualified technicians who are aware of the respective safety regulations.
Date: 22.02.1996 Subject to modification
Document-No.: 4812 718 11648
22.02.1996 / Page 2 Whirlpool Europe
Doc. No: 4812 718 11648 Customer Service
Technical data
SERVICE
Dimension
Height 82,0-87,0 cm
Width 59,5 cm
Depth 57,0 cm
Weight ~ 55,7 kg
Decor plate
Thicknes max. 4 mm
Width 584 mm
Height 595 mm
Weight max. 1,8 kg
Specification (normal program)
Capacity 12 standard
setting pl.
Water consumption 19 l
Energy consumption 1,4 kWh
Program time ~ 78 min
Noise level 49 db (A)
Detergent consumption 25 ml
Salt consumption
by 21˚ dh <20 g
Hot water connect. up to 60 ˚C
Volume (normal program)
Water Volume Level
Regeneration 0,3 l 15 mm
Back rinse 3x 1,0 l 68 mm
Prewash 5,0 l 125 mm
Prewash/Zone washing 4,0 l 120 mm
Main wash 5,0 l 125 mm
Main wash/Zone washing 3,8 l 119 mm
Intermediate rinse 1 4,5 l 123 mm
Intermediate rinse 1/
Zone washing 3,8 l 119 mm
Intermediate rinse 2 4,5 l 123 mm
Intermediate rinse 2/
Zone washing 3,8 l 119 mm
Clear rinse 4,5 l 123 mm
Clear rinse/Zone washing 3,8 l 119 mm
Safety / overflow 8,5 l 141 mm
Measuring the level
Remove the coarse sieve, put in a measuring
meter into the sump, measure the hight of the
water level.
Detergent max.
Alarms
Refill rinse aid
Refill salt
Sprayarm blocked
Options
Delay timer
Zone washing
Program information
Start indicator
Pre rinse/pre wash
Main wash
Drying
End
Pre-wash 10 cm
Main-wash 45 cm
Rinse aid 125 cm
6 Dosage steps 1 - 6 cm
Water softener
Saltcontainer 2 kg
Resin container 900 cm
Regeneration dosage 300 cm
Water pressure
Inlet pressure 0,3-10 bar
Spray pump pressure 0,4 bar
Rotations
Spray pump motor 2800 RPM
Drain pump motor 2800 RPM
Spray arm lower ~ 30 RPM
Spray arm upper ~ 35 RPM
Ceiling rotor ~ 60 RPM
SERVICE
Technical data
Whirlpool Europe 22.02.1996 / Page 3
Customer Service Doc. No: 4812 718 11648
Flow rates / Inlet volume
Flow meter (at 0,3 bar
= quantity 1,1 l/min) 208 lmp/l
Spray pump ~ 70 l/min
Drain pump 16 l/min
Pump height max. 1,3 m
Inlet valve 4,5 l/min
Valve for Zone washing 30 l/min
Valve for sieve 8 l/min
Spray arm lower 33 l/min
Sprayarm upper 30 l/min
Ceiling rotor 8 l/min
Water distribution
Fine sieve 100 %
Self cleaning
micro filter ~ 32 %
Electrical data
Base data
Potentiometer
Position 0 2,0 kΩ
Position 1 4,3 kΩ
Position 2 9,0 kΩ
Position 3 13,3 kΩ
Position 4 17,5 kΩ
Position 5 22,2 kΩ
Position 6 24,2 kΩ
Water valves
Single valve at inlet hose
Voltage 220/240 V
Frequency 50/60 Hz
Resistance 2,06 kΩ
Regenerating valve
Voltage 220/240 V
Frequency 50/60 Hz
Resistance 3,13 kΩ
Voltage 220/230 V
Frequency 50 Hz
Total power 2,0-2,2 kW
Fuse 10 A
Motor
Spray pump motor
Voltage 220/230 V
Power consumption ~190 W
HI 69 Ω
HA 36,2 Ω
Capacitor 4 F
Drain pump motor
Voltage 220/240 V
Resistance 146 Ω
Heating
Valve for zone washing
Voltage 220-240 V
Frequency 50/60 Hz
Resistance 3,71 kΩ
Valve for sieve
Voltage 220/240 V
Frequency 50/60 Hz
Resistance 3,83 kΩ
Coil of dispenser
Voltage 220/240 V
Frequency 50/60 Hz
Resistance 1,43 kΩ
Relay
Heating relay
1 Element system
Voltage 220/230 V
Power consumption 1,8/2,0 kW
Resistance 12,5-13,5 Ω
Heating speed ~ 2,5 ˚C/min
Temperature on surface ~ 115 ˚C
Double safety thermostat
self reset 85 ˚C
Voltage 220/240 V
Frequency 50/60 Hz
Resistance 5,5 kΩ
22.02.1996 / Page 4 Whirlpool Europe
Doc. No: 4812 718 11648 Customer Service
Technical data
SERVICE
Reedcontact
flow meter
salt control
rinse aid control
Spray arm block
NTC
15 ˚C 75 kΩ
20 ˚C 62 kΩ
30 ˚C 43 kΩ
40 ˚C 28 kΩ
50 ˚C 19 kΩ
60 ˚C 13 kΩ
70 ˚C 9 kΩ
80 ˚C 6 kΩ
85 ˚C 5 kΩ
Regeneration
Volume 300 cm
Position 0
after wash cycles -water hardness 0-5 ˚dh
0-0,9 mmol/l
0-9 ˚Fh
Position 1
after wash cycles 6-8
water hardness 6-10 ˚dh
1-1,8 mmol/l
10-18 ˚Fh
Position 2
after wash cycles 5-6
water hardness 11-15 ˚dh
1,9-2,7 mmol/l
19-27 ˚Fh
Position 3
after wash cycles 4
water hardness 16-21 ˚dh
2,8-3,7 mmol/l
28.37 ˚Fh
Position 4
after wash cycles 3
water hardness 22-28 ˚dh
3,8-5,0 mmol/l
38-50 ˚Fh
Position 5
after wash cycles 2
water hardness 29-35 ˚dh
5,1-6,3 mmol/l
51-63 ˚Fh
Position 6
after wash cycles 1
water hardness 36-60 ˚dh
6,4-10,7mmol/l
64-107 ˚Fh
Salt consumption
for regeneration 77 g
Number of cycles
with 2 kg salt 26
Whirlpool Europe 22.02.1996 / Page 4
SERVICE
Customer Service Doc. No: 4812 718 11648
Spare part list
Model ADP 952 WHM
Service No. 854295261010
Version 854295261010
Pos. No. 12NC Code Description
004 0 4812 440 18952 Drip tray assy
004 1 4812 401 18402 Holder
011 0 4812 505 18369 Foot long
022 0 4812 440 19362 Side panel left
022 1 4812 440 19361 Side panel right
022 2 4812 440 18953 Spacer
024 0 4812 440 18948 Panel, rear
040 1 4812 417 18774 Hinge left
040 2 4812 417 18773 Hinge right
040 3 4812 417 18784 Protector f.door (set)
044 0 4812 492 38354 Spring f.door
044 1 4812 492 38356 Spring f.cap
047 0 4812 404 48591 Brake f.door
047 1 4812 401 18397 Band,brake
047 2 4812 404 68023 Hook
053 0 4812 440 88106 Plinth
053 1 4812 440 19359 Plinth
053 2 4812 440 19363 Angle iron
053 3 4812 440 19358 Plinth extension
061 0 4812 466 88453 Counter weight
065 0 4812 466 48051 Insulation
103 0 4812 440 18956 Door outer WH
120 0 4812 440 18961 Door,inner
120 1 4812 440 18955 Batten
130 0 4812 417 58361 Tilt lock
Pos. No. 12NC Code Description
263 1 4812 520 48001 Ball Niro 8 D
265 0 4812 404 48599 Basket adjustm. cpl.
265 2 4812 404 48589 Grip basket adjustment
301 0 4812 453 79536 Control panel WH
303 1 4812 417 58364 Child-prooflock cpl. WH
305 0 4812 440 18964 Batten WH
322 0 4812 453 79562 Insert panel WH
331 0 4812 413 58865 Knob program cpl. WH
332 0 4812 410 28528 Push button cap WH
350 0 4812 276 58037 Display board (DB)
351 1 4812 381 28021 Guide,light
400 0 4812 259 28654 Motor with spray pump cpl.
405 0 4812 360 18358 Spray pump
405 1 4819 515 28158 Gasket
420 0 4812 121 18132 Capacitor
430 0 4812 360 18357 Pump,draining
430 1 4812 466 68506 Ring,sealing
450 0 4812 259 28657 Heating element
480 0 4812 321 28364 Cable harness set
490 0 4812 321 18019 Cable,mains 5m (without plug)
490 0 4812 321 18026 Cable,mains 3m
490 0 4812 401 18394 Cable,mains 1,6m
521 0 4812 214 78151 Control board (CB) kit
531 0 4812 273 18051 Switch waterhardness
531 1 4812 273 18052 Wheel,fingertip
131 0 4812 401 18403 Hook lock
175 0 4812 310 18295 Trim,ornamental left WH
175 1 4812 310 18294 Trim,ornamental right WH
175 2 4812 310 18296 Trim,ornamental lower WH
191 0 4812 466 68534 Gasket door
192 0 4812 466 68467 Gasket, door lower
200 0 4812 418 18183 Container cpl.
241 0 4812 458 18276 Basket upper straight
241 1 4812 458 18283 Holder cups right WH to 96/09
241 1 4812 458 18284 Holder cups right GR from 96/09
241 2 4812 535 78033 Bearing cupholder
241 3 4812 528 88068 Wheel,basket upper (set)
241 4 4812 458 18285 Cutlerycompart. GR from 96/09
241 4 4812 458 18288 Cutlerycompart. WH to 96/09
241 5 4812 458 18269 Holder cutlery compartment
241 6 4812 458 18286 Holder cups left GR from 96/09
241 6 4812 458 18287 Holder cups left WH to 96/09
241 7 4812 404 48605 Hoop
241 8 4812 466 68482 Spacer cap set
242 0 4812 458 18274 Basket lower cpl.
242 1 4812 528 88069 Wheel,basket lower
242 2 4812 458 18262 Plate,support f.basket lower
242 3 4812 458 18275 Plate,support f.basket lower
243 0 4812 458 18296 Basket cutlery
243 3 4812 458 18289 Basket cutlery cpl.
571 2 4812 281 28362 Sieve valve
571 3 4812 281 28363 Valve f.zone-washing
575 0 4812 281 28361 Regen.valve
581 0 4812 349 28003 Counter water
583 0 4812 271 28355 Switch diaphragm
612 0 4812 280 58018 Relay heating
616 0 4812 281 18047 Contact,reed salt
616 1 4812 271 58161 Contact,reed rinsing agent
616 2 4812 271 58159 Contact,reed
620 0 4812 218 38005 User board (UB)
623 0 4812 271 38356 Microswitch
633 0 4812 271 38355 Microswitch
680 0 4812 418 68133 Combidosage
680 1 4812 466 68495 Gasket
681 1 4812 466 68497 Gasket
681 2 4812 440 18975 Flap
682 0 4812 466 68496 Gasket
691 0 4812 282 68012 Feeler NTC
700 0 4812 530 28788 Hose, inlet aqua stop 2m
700 0 4812 530 28804 Hose, inlet aqua stop 4,2m
700 1 4812 480 48019 Sieve
700 2 4812 520 58002 Gasket set
700 3 4812 462 78307 Reductor
701 1 4812 310 18153 Yoke clamp set
701 2 4819 401 18423 Holder
243 4 4812 458 18317 Bracket
261 0 4819 462 38271 Rail telescope, inner
261 1 4819 404 48819 Cap rail
261 2 4812 462 78995 Cap rail ahead
263 0 4819 520 18013 Ball cage cpl.
710 0 4812 418 68128 Monoblock
710 2 4819 310 38536 Nut threaded ring set
710 3 4819 466 69562 Gasket set
714 0 4812 462 78993 Threaded cap
714 2 4812 440 18963 Cabinet non-return flap
22.02.1996 / Page 5 Whirlpool Europe
Doc. No: 4812 718 11648 Customer Service
Spare part list
Model ADP 952 WHM
Service No. 854295261010
Version 854295261010
SERVICE
Pos. No. 12NC Code Description
716 0 4812 418 68141 Reg.dosage
716 1 4812 466 68475 Gasket
716 2 4812 462 78994 Cover
721 0 4812 360 68043 Hub lower cpl.
721 1 4812 360 68047 Arm,spray lower cpl.
721 2 4812 466 68491 Gasket 25x2,3B
721 3 4812 466 68489 Gasket 76x2,5
721 4 4812 418 18176 Cabinet
722 0 4812 360 68044 Arm,spray upper
722 2 4812 360 68048 Hub upper straight cpl.
723 0 4812 360 68049 Arm,spray
723 1 4812 466 68483 Gasket
723 2 4812 404 48597 Clip,fix sprayarm
723 3 4812 505 18362 Connect,gaspipe
726 0 4812 530 28786 Tube
726 1 4812 530 28787 Tube
726 2 4812 505 18358 Nut
726 3 4812 466 68512 Gasket
726 4 4812 462 79633 Centering
743 0 4812 511 48171 Capacitor
743 1 4812 530 28102 Hose, inlet
743 3 4812 505 18364 Nut
743 4 4812 530 28807 Hose 9x1,5x270+10
743 7 4812 466 68514 Gasket
751 0 4812 418 18169 Water collector
Pos. No. 12NC Code Description
901 5 4812 401 18406 Strap 028,6-708Z
901 6 4812 401 18408 Strap 038,1-708Z
901 8 4812 401 18393 Strap 20-32/9
902 0 4812 401 18195 Clip
902 1 4812 466 78361 Fastener f.buildt-in models
902 2 4812 404 78239 Holder
904 2 4812 462 79635 Cover WH 3,5x5
904 3 4812 462 79636 Cover WH 3,5x4
910 1 4812 502 18019 Screw
910 2 4812 502 18363 Screw 4,0x12-H
910 3 4812 502 18364 Screw 5x20-TORX
910 4 4812 502 18365 Screw 3,5x5,5-TORX
910 5 4812 502 18367 Screw 3,5x8-TORX T15
910 6 4812 502 18369 Screw A2F M4x6
910 7 4812 502 38132 Screw DIN 965
911 0 4812 502 38134 Screw decor ST3,5x9,5-C-H
964 0 4812 440 18947 Traverse
964 0 4812 466 68468 Gasket housing ri/le
964 1 4812 466 68511 Gasket housing upper
993 1 4812 466 78018 Foil protection
993 2 4812 404 48609 Socket wreng foot
993 5 4822 532 80216 Funnel salt
751 1 4812 418 18171 Water guide
751 2 4812 440 18954 Fastener frame
755 0 4812 530 28785 Bend
755 2 4812 530 48136 Tray,leak left
755 3 4812 530 48137 Tray,leak right
756 0 4812 360 58099 Floater
761 0 4812 480 58061 Sieve fine
761 1 4812 480 58072 Sieve insert
762 0 4812 480 58055 Microfilter
763 0 4812 480 58057 Sieve coarse
781 0 4812 530 28737 Hose,draining
781 1 4819 530 28286 Sleeve hose
781 2 4819 492 68405 Clip f.non-return valve
781 3 4812 281 28364 Flap non-return
783 0 4812 530 28792 Hose 11,5x3x200
783 1 4812 530 28806 Hose connection
783 5 4812 530 28789 Distributor
783 6 4812 530 28796 Hose 10x3x180+10
791 0 4812 532 68063 Gasket
791 2 4812 530 58093 Gasket
791 3 4812 466 68502 Gasket 10x3,5
791 4 4812 466 68503 Gasket
791 5 4812 466 68504 Gasket
791 6 4812 466 68505 Gasket
794 1 4819 530 58032 Gasket 20x2,5
901 0 4812 401 18191 Strap 017,8
901 1 4812 401 18396 Strap
901 2 4812 401 18401 Strap
901 3 4812 401 18404 Strap 019,8-708Z
901 4 4812 401 18405 Strap 025,6-708Z
Loading...