Whirlpool ADP 6650 WH, ADP 6650 IX Product Sheet
Quick reference guide
Chart
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
WASH TIME DISPLAY
Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected
it indicates the time remaining until program start (h.00) - below 1h (0:min).
If “Fx Ey” messages appears on the display, see page 9 - chapter “What to do if...”.
PROGRAMS
SELECTION
BUTTON
Push “Programs”
button (repeatedly)
until the indicator of the
required program lights
up (see “Table of
programs” - next page).
MULTIZONE
Allows you to choose
the washing zones.
Press this button
(repeatedly) to select
the wash zones:
both racks
only lower
rack
only upper
rack (including
cutlery rack)
- indicator lits
ANTIBACTERIAL
3)
RINSE
This function activates
an antibacterial rinse at
the end of the wash
cycle, guaranteeing a
further reduction of
bacteria. Press the
button to activate or
deactivate the
function. This function
can be used with the
programs indicated in
the table of programs.
The dishwasher door
must be kept shut for
the entire duration of
the program in order
to guarantee reduction
of bacteria. If the door
is opened the indicator
lamp starts flashing.
SALT INDICATOR
When lit (at the end of the
cycle), the salt reservoir needs
to be refilled.
TABLET SETTING
This setting allows to
optimize the cycle
performances according
the type of detergent
used. Push the Tablet
button for 3 seconds
(until the indicator lights
up) if you are using the
combined detergents in
tablet (rinse aid, salt and
deteregent in 1 dose). If
you are using powder
detergent or liquid
detergent, the Tablet
indicator on the control
panel has to be off.
RINSE AID INDICATOR
When lit (at the end of the
cycle), the rinse aid dispenser
needs to be refilled.
DELAYED START
BUTTON
Push the button
(repeatedly) to delay
the start of the
program. Adjustable
from 1 to 24 hours.
With each press of the
button, the delayed
start indicator
increases by one hour
and after 24 restarts
fr om 0 . Then press the
START button. The
dishwasher will start
after the set time.
START/RESUME
BUTTON
Push this button to start
the selected program:
the indicator lights up
and goes off at the end
of the program.
When the door is
opened during a
washing cycle, the
cycle is temporarily
paused: the Start
indicator blinks.
To resume the cycle
close the door and push
Start button again.
5019 396 03542
CANCEL/OFF
BUTTON
Push this button to switch
off the control panel.
If pressed when a
program is running it
cancels the program
ongoing draining water
for 1 minute (0:01 is
shown into the display).
If pressed when the
dishwasher is switched
off, it drains any
possible liquids from
dishwasher (1 minute
process).
GB
-1-
Quick reference guide
Chart
Table of programs
Deter-
P
1
2
3
4
5
6
Programs
Aqua Steam 40-70°C
Pre-Wash cold
Glasses 40°C
Quickwash 45°C
Eco
2)
50°C
Overnight 55°C
Available
options
Delay
Multizone
Antibacterial
rinse
Delay
Multizone
Delay
Multizone
Delay
Multizone
Delay
Multizone
Antibacterial
rinse
Delay
Multizone
Loading instructions Litres kWh
Soaking or hand pre-treatment is no longer
needed on any kind of items. Steam is used to
soften soil and its action is particularly effective
on coffee, tea and lipstick stain on glasses and
cups. Furthermore, thanks to the combination
with 6th Sense, optimization of time, energy
and water is guaranteed because it adapts the
washing cycle to the level of soil.
Crockery to be washed later. — 4.0 0.03 14 NO
Light soiling, for example glasses and cups. X 10.0 0.85 100 Light
Lightly soiled crockery, with no dried-on
food.
Normally soiled crockery. Energy-saving
program.
Normally soiled crockery, gentle and quiet
thanks to the lower spray pressure
(39 dbA).
gent
X 7-14 0.99-1.80 70-160 Full
X 11.0 0.80 30 NO
X 6.0 1.03 170 Full
X 10.0 1.20 290 Light
Consumption
Minutes
1)
Drying
Phase
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary
depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard
loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
RECYCLING WATER SYSTEM: these programs save water in a dedicated tank.
A TANK CLEANING CYCLE (at least 30 min.) is automatically run every 30 cycles or after every power off, to assure the best product conditions.
GB
-2-
How to set water hardness in order to always assure the best cleaning results
First time use
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
Water hardness should be set
only before the first wash or if
water hardness has been
changed
Water hardness level is
factory set for medium-hard
water (level 4).
Even if you use tablets
which include salt
functionality, you must still
add regeneration salt since
such detergents are not
effective enough at
softening hard water.
At first time use, the salt reservoir has to be filled independently from water hardness level
Filling the salt reservoir -
1
The salt level indicator lamp may remain lit
at the end of several wash cycles. If the
water hardness level falls within category
(soft), no salt is required.
Dissolve limescale (not necessary if water hardness level is set to “soft”!)
Visual indicator
(depending
on the model).
Unscrew cap.
-Press and hold together
- The current water hardness setting will be visible on the display.
-Press the
- Wait 30 seconds (control panel switches off) or press
1.
degrees °dH
Programs
the start button will set the level back to 1).
Ask your water supply company what the
German
0 - 5 0 - 9 0 - 6.3 Soft 1
6 - 10 10 - 18 7 - 12.6 Medium 2
11 - 15 19 - 27 13.3 - 18.9 Average 3
16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4 if water is
22 - 28 38 - 50 26.6 - 35 Hard 5
29 - 35 51 - 63 35.7 - 44.1 Very hard 6
36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7
degrees °fH
Programs
button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of
French
English
degrees °eH
CANCEL/Off
and
water hardness
Water hardness
buttons for minimum 3 seconds.
Start/Resume
is...2....enter this value
level
button to save setting.
on your dishwasher
Insert value is shown
in the display
Suggestions for detergent use
Gel or Powder
(rinse aid and salt)
go to step 1
(see “Daily
check”)
(see description below in step 1 “Daily check”).
HARD extra salt
needs to be
(go to step 1,
“Daily check”)
Daily check
Screw on the cap.
Salt residual
around the cap
need to be
removed. Some
salt reservoir have
a level indicator
integrated in the
cap (see below
how to check).
Add salt
Fill the salt reservoir with water
before the first wash only.
(depending on the model)
Salt indicator on the control panel Salt indicator on the salt reservoir cap
The indicator lamp lights up when SALT
NEEDS TO BE ADDED.
(never add detergent!)
min. 0.8 kg/max. 1 kg
green: OK.
clear: NEEDS TO
BE ADDED
Ta bl e ts
added
GB
-3-
Adding rinse aid
(not necessary when you use tablets). How to adjust the rinse aid dosage regulator
Daily check
Visual
2
Check the rinse aid indicator to check the
level into the dispenser.
Only use rinse aids recommended for use in domestic dishwashers.
a fault function of the appliance.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6).
Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder
detergent). Detergents with rinse aid incorporated tend to form excess suds.
Adding detergent -
(press the dedicated button).
Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Open the cover A
3
indicator
If required,
open the
cover B
(press the
dedicated
button).
rinse
Add
aid
to the
max. line
~150 ml
(depending on the model)
Rinse aid indicator on the control panel Rinse aid indicator on the dispenser
The indicator lamp lights up when
RINSE AID NEEDS TO BE ADDED.
Immediately
Insert detergent:
Only fill the
detergent
dispenser prior to
starting a wash
program.
wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause
Tablet / powder / liquid
into the big chamber.
The rinse aid dosage can be
adjusted to the detergent
used. The lower the setting,
the less rinse aid is dispensed
(factory setting: position 4).
Press the button to open the
cover B. Using a coin or
similar object, turn the arrow
to the desired setting. After
adjusting the rinse aid setting,
shut the cover again.
dark: OK. clear: NEEDS TO BE ADDED
Shut the cover
by pressing dedicated ribs.
Use only one tablet per one cycle,
only placed in detergent
dispenser.
All types of tablets can be used,
but for 2 in 1 type adding of salt is
mandatory.
Daily use
GB
-4-
Loading...