Whirlpool ADP 4300 WH User Manual
SERVICE
Model ADP 4300 WH
Version 8511 764 43810 Page
Whirlpool Europe
Customer Services
ADP 4300 WH
Service Manual
Dishwasher
ADP 4300 WH
Technical data 2 - 4
Spare part list 5 - 6
Exploded view 7 - 8
Circuit diagram 9
Program diagram 10
Text/Legend 11 - 16
Family WRC - IC
LOW 3
This documentation is only intended for qualified technicians who are aware of the respective safety regulations.
Date: 19.07.2005 Subject to modification
Document-No.: 4812 728 11578
19.07.2005 / Page 2 ADP 4300 WH Whirlpool Europe
Doc. No: 4812 728 11578 8511 764 43810 Customer Service
Technical data
Dimension
Exception: Switching off the appliance or unplug
Height 82.0 - 87.0cm
Width 59.7 cm
Depth 55.5 cm
Weight 50 kg
the appliance during the drying phase, this will lead
directly to the end of the program.
Water Volume at permanent spray system
SERVICE
Wooden door for Integrable types
Thickness min. 16 mm
Thickness max. 20 mm
Width min. 592 mm
Width max. 595 mm
Height min. 515 mm
Height max. 600 mm
Weight max. 5.5 kg
Max. stick out over lower
edge of appliance door 92 mm
Height of plinth min. 93 mm
Electronic boards
Service boards see spare part list
Serial boards see on the boards itself
Programmed control board and programing of
version, see „Board Service“and„DATA“onrating
plate of inner door:
UCB 704812
Data set 704802
Basic UCB, not programmed
see on the board itself 4619 727 04651
Water Volume Level
Regeneration 0.3 l 15 mm
Back rinse 3x 1.0 l 60 mm
Prewash 4.8 l 120 mm
Main wash 4.2 l 118 mm
Intermediate rinse 1 4.2 l 118 mm
Intermediate rinse 2 4.2 l 118 mm
Clear rinse 4.2 l 118 mm
Safety/ overflow 8.5 l 141 mm
Measuring the level
Remove the coarse sieve, put in a measuring
meter into the sump, measure the hight of the
water level.
Detergent max.
Pre-wash 10 cm
Main-wash 40 cm
Rinse aid 135 cm
6 Dosage steps 1 - 6 ml
Water softener
3
3
3
Succession of programs
Programs see program diagram
Succession P3a-P5b-P7a
Datas Energy Label
Reference program P5b
Energy Performance B
Cleaning Performance B
Drying Performance C
Program information
Start indicator
All programs will be locked after start. Changing
the program or finishing the program will be
possible only after pressing the start button for
longer then 1.5 sec. (Break by customer)
A switching off the appliance or unplug the
appliance for a while, this will frozen the program
step and later on, the program continuos on the
same position.
Saltcontainer 2 kg
Resin container 700 cm
Regeneration dosage 300 cm
Water pressure
Inlet pressure 0.3 - 10 bar
Spray pump pressure 0.3 bar
Rotations
Spray pump motor 2800 RPM
Drain pump motor 3000 RPM
Spray arm lower 30 - 40 RPM
Spray arm upper 30 - 40 RPM
3
3
SERVICE
Technical data
Whirlpool Europe ADP 4300 WH 19.07.2005 / Page 3
Customer Service 8511 764 43810 Doc. No: 4812 728 11578
Flow rates/ Inlet volume
Flow meter (at 0.3 bar = quantity 1.1 l/min)
208 lmp/l
Spray pump 65 l/min
Drain pump 16 l/min
Pump height max. 1.1 m
Inlet valve 4 l/min
Spray arm lower ~ 33 l/min
Sprayarm upper ~ 27 l/min
Sprayarm/ Shower top ~ 8 l/min
Electrical base data
Voltage 220/ 240 V
Frequency 50 Hz
Total power 2.0 - 2.2 kW
Fuse 10 A
Spray pump motor - permanent spray system
Voltage 220/ 240 V
Power consumption 80 W
Frequency 50 Hz
Resistance 30 Ω
Regenerating valve
Voltage 220/ 240 V
Frequency 50/ 60 Hz
Resistance 3.13 kΩ
Coil of dispenser
Voltage 220/ 240 V
Frequency 50/ 60 Hz
Resistance 1.3 kΩ
Reed contacts
flow meter
NTC
20 ˚C 58.1 kΩ
25 ˚C 47.1 kΩ
30 ˚C 38.2 kΩ
40 ˚C 25.4 kΩ
50 ˚C 17.2 kΩ
60 ˚C 11.8 kΩ
70 ˚C 8.3 kΩ
80 ˚C 6 kΩ
85 ˚C 4 kΩ
Drain pump motor
Voltage 220/ 240 V
Power consumption 30 W
Resistance 146 Ω
Heating - 1 Element system
Voltage 220/ 240 V
Power consumption 1.87/ 2.04 kW
Resistance 24.5 Ω
Heating speed ~ 2.0 ˚C/min
Temperature on surface ~ 115 ˚C
Safety thermostat
self reset
(Temperature of water) ~ 85 ˚C
Fuse 206 ˚C
Water safty options
Waterstop system Electronic aqua control
Regeneration
Volume 300 cm
after wash cycles depending on the water
softener setting
water hardness 0 - 40 ˚dh
0 - 10.7 mmol/l
0 - 107 ˚Fh
Salt consumption
for regeneration ~ 77 g
Number of cycles
with 2 kg salt ~ 26
3
Single electric water inlet valve
Voltage 220/ 240 V
Frequency 50/ 60 Hz
Resistance 3.76 kΩ
19.07.2005 / Page 4 ADP 4300 WH Whirlpool Europe
Doc. No: 4812 728 11578 8511 764 43810 Customer Service
Technical data
Water softener setting
To change the water softener setting:
• Push the POWER button on
• Change to program 2
• Hold the START button for 5 seconds until the LED is flashing
• Water softener setting is shown by flashing LED
• By pushing the START button you can change the setting
• Push the POWER button off to save and exit the water softener setting
SERVICE
Water hardness Germandegrees
˚dH
1 soft 0 - 5 0 - 9 0 - 6,3 0 - 0.9 1 x
1 - 2 soft/ medium 6 - 10 10 - 18 7 - 12.6 1 - 1.8 2 x
2 medium 11 - 15 19 - 27 13.3 - 18.9 1.9 - 2.7 3 x
3 medium/ hard 16 - 21 28 - 37 19.6 - 25.9 2.8 - 3.7 4 x (DEFAULT SETTING)
4 hard 22 - 28 38 - 50 26.6 - 35 3.8 - 5.0 5 x
4 very hard 29 - 35 51 - 63 35.7 - 44.1 5.1 - 6.3 6 x
4 extremely hard 36 - 60 64 - 107 44.8 - 74.9 6.4 - 10.7 7 x
French degrees
˚fH
English degrees
Clarke ˚e
mmol/l Water softener setting is
shown by flashing LED
Accesory
If you need spare parts apart from the spare part list have a look in the Service Bulletin 4812 718 40084.
For higher mounted Dishwashers to prevent the drain off effect - also usable for lower drain pipes and to
prevent the failure F8 use Kit 4812 310 18993.
Whirlpool Europe ADP4300WH 19.07.2005 / Page 5
SERVICE
Customer Service 8511 764 43810 Doc. No: 4812 728 11578
Spare part list
Model ADP 4300 WH
Service No. 851176443810
Version 851176443810
Pos. No. 12NC Code Description
003 0 4812 440 19594 Traverse
004 0 4812 440 18952 Drip tray assy
004 1 4812 401 18402 Holder
011 0 4812 505 18357 Foot short
022 0 4812 440 10755 Side panel left
022 1 4812 440 10754 Side panel right
024 0 4812 440 10417 Panel, rear
024 5 4812 440 10944 Damper fix Motor synch
030 0 4812 310 18916 Table top cpl. WH
034 0 4812 404 78237 Spacer
040 1 4812 417 18774 Hinge left
040 2 4812 417 18773 Hinge right
040 3 4812 417 19172 Protector f.door (set)
044 0 4812 492 38358 Spring f.door
047 0 4812 404 48746 Brake f.door
047 1 4812 401 18397 Band,brake
047 2 4812 404 68023 Hook
053 0 4812 440 89031 Plinth WH
061 0 4812 466 88672 Counter weight
103 0 4812 440 10758 Door outer
120 0 4812 440 19456 Door,inner
120 1 4812 440 18969 Batten
130 0 4812 417 58373 Tilt lock cpl. bk
131 0 4812 401 18416 Hook lock
191 0 4812 466 68564 Gasket door
Pos. No. 12NC Code Description
490 0 4819 321 18136 Cable,mains 2m SA
490 1 4812 321 28367 Strain relief
521 0 4812 218 38218 User board (UCB)
521 8 4812 530 78066 Axle program knob grey
571 0 4812 281 28379 Valve inlet
575 0 4812 281 28361 Regen.valve
583 0 4812 271 28407 Switch diaphragm
621 0 4819 410 29004 Switch ON/OFF
633 0 4812 271 38355 Microswitch door
680 0 4812 418 68332 Combidosage cpl.
680 1 4812 466 68495 Gasket
681 1 4812 466 68497 Gasket
681 2 4812 440 18975 Flap
682 0 4812 466 68496 Gasket
691 0 4812 282 68035 Feeler NTC
701 0 4812 530 28081 Hose, inlet 3/8Z cpl. 5m
701 1 4812 310 18302 Yoke
701 2 4822 480 50159 Sieve inlet
710 0 4812 418 68149 Monoblock
710 2 4812 310 38896 Threaded ring
710 3 4819 466 69562 Gasket set
714 0 4812 462 79906 Threaded cap saph
716 0 4812 418 68147 Reg.dosage with flowmeter
716 1 4812 466 68475 Gasket
716 2 4812 462 78994 Cover
192 0 4812 466 68467 Gasket, door lower
241 0 4812 458 19027 Basket upper straight
241 1 4812 458 18324 Holder cups right wh
241 3 4812 528 88068 Wheel,basket upper (set)
241 8 4812 466 68553 Spacer cap set
241 9 4812 528 88101 Wheel,basket basket upper
242 0 4812 310 28134 Basket lower KIT
242 1 4812 528 88069 Wheel,basket lower wh
242 4 4812 466 48091 Fixation grey
243 0 4812 458 18272 Basket cutlery
261 0 4812 462 79831 Rail telescope, inner
261 1 4812 462 79768 Cap rail rear
261 2 4812 310 18972 Cap rail front
263 0 4819 520 18013 Ball cage cpl.
263 1 4812 310 48026 Service kit balls plastic
301 0 4812 453 72769 Control panel ADP 4300 WH
301 1 4812 452 79742 Nameplate Whirlpool
303 1 4812 460 38148 Plate,handle
331 0 4812 413 59155 Knob program cpl. WH
332 0 4812 410 29163 Button Start
332 3 4812 410 29166 Button ON/OFF WH
350 2 4812 381 28068 Light guide
400 0 4812 361 58334 Motor +SP,50Hz,per.HP-PNT
400 1 4812 466 68776 Spacer support motor/sp
421 0 4812 121 18158 Interf.filter
717 1 4812 462 79793 Stopper
721 1 4812 360 68689 Spray arm lower. cpl. sa
722 0 4812 360 68687 Spray arm upper sa
722 2 4812 360 68693 Spray arm 2nd level cpl. saph
723 0 4812 360 68691 Douche ceiling
726 1 4812 530 29331 Tube assembly cpl.saph
726 2 4812 505 18208 Nut
743 1 4812 530 28102 Hose, inlet
751 0 4812 418 18338 Water collector
755 0 4812 530 29119 Bend
755 2 4812 530 48148 Tray,leak
761 0 4812 480 58122 Sieve fine
761 2 4812 418 18337 Cover sieve
761 3 4812 418 18341 Cover
761 4 4812 530 58141 O-Ring
763 0 4812 480 58123 Sieve coarse
781 0 4812 530 29113 Hose,draining
781 3 4812 281 28417 Flap non-return
783 4 4812 530 28888 Hose
783 6 4812 530 28796 Hose 10x3x180+10
791 0 4812 532 68099 Gasket
791 2 4812 530 58093 Gasket
791 4 4812 466 68503 Gasket
791 5 4812 466 68504 Gasket
901 0 4822 401 10258 Clamp,hose 10-18 mm
430 0 4812 360 18508 Pump,draining cpl.
430 1 4812 466 68689 Gasket
450 0 4812 259 28684 Heating element
480 0 4812 321 28424 Cable harness (EBL) without LS6
480 3 4812 401 18418 Protector f.wiring
901 1 4812 401 18424 Strap 050,0
901 2 4812 401 18157 Strap 32-50/9 C61
901 5 4812 401 48573 Strap 028,6
904 0 4812 462 78998 Threaded cap
904 3 4812 462 79636 Cover WH 3,5x4
Loading...