Whirlpool ADG 955/3 NBM, ADG 955/3 IXM, KRDD 9010 INSTRUCTION FOR USE
GB
ADG 955
PROGRAMME CHART
Salt level indicator
Add regeneration salt.
Programme progress indicator
Pre-rinse
Only lights up for programmes with prewash (the
symbol “+” in the table below indicates that detergent
must be added).
Rinse /Washing
Drying
End
Programme end
Programme
Symbol
and temperature
Pre-rinse
Rapid 40° C
Eco 50° C
Universal 65° C
Normal 65°C
*) Values for normal conditions. Values may vary in relation to usage, e.g.: different loads, water temperatures, water hardness and power supply voltage.
2)
1)
Crockery to be washed later.
Lightly soiled crockery with no dried-on food.
Normally soiled crockery with dried-on food.
Normally soiled crockery.
Normally or heavily soiled crockery.
Crockery and cutlery
Half Load / Multizone button
Load the upper or lower rack only. This function
can be used with any programme.
Press once = upper rack
Press twice = lower rack
Press 3 times = Off (half load function
deactivated).
Delayed start button
Starts the dishwasher at the set time.
It is possible to programme a delay of 3 - 6 - 9
hours.
Load
Start button indicator lamp
Switches on when the dishwasher is operating.
Flashes when a fault occurs.
Switches off at the end of the programme.
Detergent
Pre-rinse
(small
compartment)
- - 5.0 0.02 9 4.2 0.02 9
- + 13.0 0.85 30 13.0 0.75 30
+ + 16.0 1.35 86 14.5 1.30 85
- + 14.0 1.50 73 12.0 1.40 71
+ + 20.0 1.63 98 18.0 1.55 90
Washing
(large
compartment)
Consumption *
Normal load
Water
Energy
(Liter)
(kWh)
Time
(Min.)
Consumption *
Half load
Water
Energy
(Liter)
(kWh)
Time
(Min.)
1) Programme recommended when using detergents of type A (non enzyme-based detergents).
2) Programme recommended when using detergents of type B (enzyme-based detergents).
Reference programme for Test Institute and energy label.
(We reserve the right to make technical modifications)
5019 100 91178
Quick reference guide
GB
Daily check list
1. Arrange crockery so that items do
not touch each other.
2. Load cups at an inclination to
facilitate water circulation.
3. In general, place cutlery in the
basket with the handles positioned
downwards, but ensure that any
sharp knives and forks that might
cause injury are placed in the
basket with the handles positioned
upwards.
4. Make sure the water je t can reach
all loaded items and that the spray
arms rotate freely.
5. Turn on the water supply tap before
starting the dishwasher.
Important:
• Switch off the dishwasher once the
“Start” indicator lamp has
switched off. If you switch off the
dishwasher during a wash cycle,
when switched on again the
dishwasher resumes the cycle from
where it was interrupted.
• If a fault occurs or you wish to
change the current programme,
press the “START” button fo r about
5 seconds until the Start indicator
lamp switches off! Refer to the
“Troubleshooting Guide” in these
user instructions to remedy any
problems.
• If a regeneration salt is to be
added, IMMEDIATELY start a
washing programme, in
order to eliminate any
residual salt.
• Sometimes even when the
regeneration salt container is full,
the corresponding indicator
lamp may illuminate during the
first wash cycle.
Crockery holders:
• Down: cups and long-stemmed
glasses.
• Raised: plates.
Upper rack
Half load button / Multizone:
If only the upper rack is to be filled,
remove the cutlery basket from the
lower rack and place it in the upper
one.
Height adjustment:
(The dishwasher is delivered with the
upper rack in the top position).
The dishwasher is delivered with the
upper rack in the top position.
• To lower: pull out the two side
handles and gently lower the rack.
• To raise: pull up the two side
handles until the rack clicks into
place.
• The rack must be level on both
sides.
Lower rack
Half load button / Multizone:
Loading the lower rack only:
greater washing power, particularly for
plates and saucepans.
Cutlery basket:
The cutlery basket can be removed to
increase available space.
Plate holders:
• The plate holders may be
removed to increase available
space.
• To remove: pull the handle up.
• To reposition: simply insert in the
required position (normal or
crosswise).
Loading...