Sears Kenmore/Whirlpool Front Load Washer
Error Codes: 02F dLF
Model: 110.44832 200 (110. = Whirlpool)
S/N: CSP 1903874
Type: 199-AKP 705/WT
SOURCE: www.applicancepartspros.com
WHIRLPOOL FAULT CODES
Whirlpool Duet Front Loading Automatic Washer Fault Codes
Failure Fault Code Description Solution
Code
FH |
No water detected entering |
If after 30 seconds the control does not detect water |
|
machine or Pressure switch trip |
entering machine and then valves will be turned off and |
|
not detected. |
the error code will be displayed. |
|
|
Or |
|
|
If the control has turned the water valves on and after 8 |
|
|
minutes the flow meter has detected 10.5 gallons of |
|
|
water passing through it, but has not detected the |
|
|
pressure switch trip, the valves will be turned off and the |
|
|
error code will flash. |
|
|
Press PAUSE/CANCEL twice to clear the display. |
|
|
Potential Causes |
|
|
• If there is no water in the unit: |
|
|
- Make sure that both valves at the water source(s) are |
|
|
turned on all the way. |
|
|
- Check for plugged or kinked inlet hoses or plugged |
|
|
screens in the inlet valves |
|
|
- Verify inlet valve operation |
|
|
• If there is water in the unit: |
|
|
- Verify Drain pump operation |
|
|
- Pressure Switch Hose is in good condition and |
|
|
properly connected to Tub and Pressure switch |
|
|
• Verify there is not a siphon problem |
|
|
• Verify wire harness connections to; Inlet Valves, |
|
|
Pressure Switch, Drain Pump, Flow Meter, and Central |
|
|
Control Unit (CCU) |
|
|
• Check all hoses for possible leaks |
|
|
• Verify pressure switch operation |
|
|
• Verify flow meter operation |
|
|
• Verify CCU operation |
|
|
Replace failed component. |
|
|
|
F02 |
Long Drain |
If the drain time exceeds 8 minutes, the water valves are |
|
|
turned off and F02 is flashed. |
|
|
Press PAUSE/CANCEL twice to clear the display. |
|
|
NOTE: After 4 minutes the “Sud” error will be displayed, |
|
|
then 4 minutes later the F02 error code will be displayed. |
|
|
Potential Causes |
|
|
• Check the drain hose and make sure it is not plugged or |
|
|
kinked |
|
|
• Check the electrical connections at the pump and make |
|
|
sure the pump is running. |
|
|
• Check the drain pump filter for foreign objects |
|
|
• If the above does not correct the problem replace the |
|
|
pump |
|
|
|
F05 |
Water temperature sensor error |
If during the water heating step in the wash cycle, the |
|
|
water temperature sensor (NTC) value is out of range, or |
|
|
the heating element circuit has failed, the F05 error code |
|
|
will be displayed. |
|
|
Potential Causes |
|
|
• Check the Water Temperature Sensor, Heating Element |
|
|
and Element Relay |
|
|
• Check connections to the Sensor, Heating Element and |
|
|
Relay |
|
|
Replace failed component. |
|
|
|
F06 |
Drive motor tachometer error |
The control is unable to properly detect motor speed and |
|
|
the machine will shut down. If a failure occurs during |
|
|
high-speed spin the door will be unlocked after 3 |
|
|
minutes. |
|
|
Potential Causes |
|
|
• Check wire harness connections between the Drive |
|
|
Motor/Tachometer and the Motor ControlUnit (MCU), and |
|
|
between the MCU and the Central Control Unit (CCU) |
|
|
• Check the Drive Motor |
|
|
• Check the MCU |
|
|
• Check the Wire Harness |
|
|
Replace failed component. |
|
|
|
F07 |
Motor control unit error |
The Central Control Unit has detected a short in the |
|
|
motor control unit. If a failure occurs during high-speed |
|
|
spin the door will be unlocked after 3 minutes. |
|
|
Potential Causes |
|
|
• Check wire harness connections between the Drive |
|
|
Motor and the Motor Control Unit (MCU), and between |
|
|
the MCU and the Central Control Unit (CCU) |
|
|
• Check the MCU |
|
|
• Check the Drive Motor |
|
|
• Check the Wire Harness |
|
|
Replace failed component. |
|
|
|
F09 |
Overflow condition |
If the Overflow contact on the pressure switch is Closed |
|
|
for more than 60 seconds an Overflow condition will |
|
|
occur. In an Overflow condition, the Door will remain |
|
|
locked, and the Drain Pump will run constantly, even if |
|
|
PAUSE/CANCEL is pressed twice and the Display is |
|
|
cleared. Unplug the unit to service. |
|
|
|