IK007 Integration kit |
Refrigeration |
Installation manual |
|
STM3900, STM4200, SBM3800, SBM4300, WTM2800, WTM3000, WTM3300, WTM3900, WTM4200, WTM4400, WTM5200, WTE4200, WTE5200, WTB2300, WTB2500, WTB2800, WTB3400, WTB3700, WBM3700, WBM3800, WBM4000, WBM4300, WBM5100, WBE4300, WBE5100, WRM3700, WRM4300,WFM3000, WFM3600, KTM2800, KTM3000, KTM3300, KTM3600, KTM3900, KTM4200, KTM4400, KTM5200, KBM3800, KBM4300, KBM5100.
2
Congratulations
Congratulations and thank you for choosing our integration kit. Before you install the integration kit, we recommend that you read through the entire installation manual.
To avoid the risks that are always present when you install an electrical appliance, it is important that the integration kit and appliance is installed correctly. Please read the safety instructions in this installation manual as well as the appliance’s user manual to carefully to avoid misuse
and hazards.
We recommend that you keep this instruction booklet for future reference and pass it on to any future owners.
After unpacking the integration kit, please check it is not damaged. If in doubt, do not use the integration kit but contact your local Electrolux Customer Care Centre.
Contents
3General warnings
4Refrigerator integration kit items
5Cupboard dimensions
8Installation of 120˚ hinge
9Preparation
9Attaching top hinge bracket
10Attaching slide-housing to refrigerator doors
12Placing refrigerator in cupboard
12Refrigerator alignment
13Securing refrigerator in cupboard
14Attaching slide-bar to cupboard door
BEFORE YOU CALL
Please ensure you read the instruction manual fully before you call for service, or a full service fee could be applicable.
Information on disposal for users
ENVIRONMENT!
• Most of the packaging materials are recyclable.
Please dispose of these materials through your local recycling depot or by placing them in appropriate collection containers.
•If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.
3
General Warnings
Please read the user manual carefully and store in a handy place for later reference. Pass the user manual on to possible new owners of the appliance.
NOTE: We strongly recommend that a professional builder/cabinetmaker builds this unit into required cabinetry prior to finished installation in customer’s kitchen. Electrolux cannot take responsibility for any installation issues when customer retrofits this product into cabinetry. Cabinet door height built in excess of refrigerator door height will be unsupported and risk bowing.
NOTE: Please refer to your Appliance User Manual for warnings relating to the appliance.
SYMBOLS
Important!
This symbol indicates tips and information about use of the appliance.
ENVIRONMENT!
This symbol indicates tips and information about economical and ecological use of the appliance.
4
Refrigerator integration kit items
Because this kit is common to a variety of models, you need to select the items required to suit your model. The items required for the models covered in this instruction booklet are shown below.
Those items not required on your particular model should be discarded.
Item |
Quantity in kit |
Quantity required |
Description |
|
|
Two door model |
Single door model |
Top hinge bracket |
1 |
1 |
1 |
PNº 1433129 |
|
|
|
Slide-housing |
2 |
2 |
1 |
PNº 1445132 |
|
|
|
|
|
|
|
Slide-bar |
2 |
2 |
1 |
PNº 1421620 |
|
|
|
Location bracket |
1 |
1 |
1 |
front footing |
|
|
|
PNº 1444993 |
|
|
|
Note: this part is to be used |
|
|
|
on all models other than |
|
|
|
WTB2300, WTB2500, |
|
|
|
WTB2800, WTB3400 & |
|
|
|
WTB3700. |
|
|
|
|
|
|
|
Refrigerator |
8 |
8 |
4 |
screws |
|
|
|
PNº 741249 |
|
|
|
|
|
|
|
Cupboard screws |
12 |
12 |
8 |
PNº 1449422 |
|
|
|
|
|
|
|
120º hinge |
5 |
5 (3+2) |
3 |
PNº 1457832 |
|
|
|
Mounting plate |
5 |
5 (3+2) |
3 |
for hinge |
|
|
|
PNº 1458211 |
|
|
|
|
|
|
|
Self tapping |
20 |
20 |
12 |
wood screws |
|
|
|
PNº 1458212 |
|
|
|
|
|
|
|
Z bracket |
1 |
1 |
0 |
IK foot location |
|
|
|
PNº 808958001 |
|
|
|
(Used in models WTB2300, WTB2500, WTB2800, WTB3400 & WTB3700)
5
Cupboard dimensions
Important!
Pages 5, 6, 7 and 8 should be given to the person responsible for cupboard design and construction.
The cupboard dimensions required for each model are shown on page 6, 7 & 8.
1.All sizes are internal and measured in millimetres.
2.It is important to ensure that the correct cupboard sizes are used to ensure adequate air flow around the refrigerator.
3.Cupboard hinges should be a 120° opening type. (Use hinges supplied).
4.Three hinges should be used on each cupboard door higher than 1000mm.
5.Ensure the refrigerator is not connected to a power supply whilst installation takes place.
6.Each operation should be carried out in the sequence specified in this instruction sheet.
NOTE: All sizes are internal and in millimetres.
|
Dim ‘A’ |
Dim ‘B’ |
Dim ‘C’ |
Dim ‘D’* |
Dim ‘E’ |
Dim ‘G’ |
Dim ‘H’ |
Dim ‘I’* |
|
Model |
(mm) |
(mm) |
(mm) |
(mm) |
(mm) |
(mm) |
(mm) |
(mm) |
|
|
minimum |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 door top freezer models |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
WTB2300 |
1485 |
680 |
645 |
910 |
450 |
270 |
250 |
|
|
WTB2500 |
1550 |
680 |
645 |
975 |
450 |
270 |
250 |
|
|
WTB2800 |
1650 |
680 |
645 |
1075 |
450 |
270 |
250 |
|
|
WTM2800, KTM2800 |
1640 |
680 |
700 |
1047 |
500 |
219 |
300 |
|
|
WTM3000, KTM3000 |
1710 |
680 |
700 |
1117 |
500 |
219 |
300 |
|
|
WTM3300, KTM3300 |
1810 |
680 |
700 |
1217 |
500 |
219 |
300 |
|
|
WTB3400 |
1690 |
715 |
700 |
1110 |
500 |
298 |
300 |
|
|
KTM3600 |
1730 |
680 |
795 |
1137 |
600 |
241 |
395 |
|
|
WTB3700 |
1800 |
715 |
700 |
1220 |
500 |
298 |
300 |
Please |
|
WTM3900, KTM3900, STM3900 |
1810 |
680 |
795 |
1217 |
600 |
241 |
395 |
use the |
|
WTM4200, WTE4200, KTM4200, STM4200 |
1730 |
740 |
795 |
1137 |
600 |
241 |
395 |
calculation |
|
WTM4400, KTM4400 |
1810 |
740 |
795 |
1217 |
600 |
241 |
395 |
below to |
|
WTM5200, WTE5200, KTM5200 |
1810 |
740 |
895 |
1217 |
600 |
278 |
495 |
measure |
|
|
|
|
|
|
|
|
|
Dimension |
|
2 door bottom freezer models |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
‘I’ for your |
||
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
specific |
|
WBM3700 |
1660 |
740 |
745 |
702 |
600 |
241 |
395 |
||
model. |
|||||||||
WBM3800, KBM3800, SBM3800 |
1810 |
680 |
795 |
702 |
600 |
241 |
395 |
||
|
|||||||||
WBM4000 |
1760 |
740 |
745 |
702 |
600 |
241 |
395 |
|
|
WBM4300, WBE4300, KBM4300, SBM4300 |
1810 |
740 |
795 |
702 |
600 |
278 |
395 |
|
|
WBM5100, WBE5100, KBM5100 |
1810 |
740 |
895 |
702 |
600 |
|
495 |
|
|
|
|
|
|
|
|
|
|
|
|
single door models |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
WFM3000 |
1810 |
680 |
700 |
– |
500 |
219 |
300 |
|
|
WFM3600 |
1810 |
680 |
795 |
– |
600 |
241 |
395 |
|
|
WRM3700 |
1810 |
680 |
700 |
– |
500 |
219 |
300 |
|
|
WRM4300 |
1810 |
680 |
795 |
– |
600 |
241 |
395 |
|
|
|
|
|
|
|
|
|
|
|
Step 1
Measure and confirm Dimension ‘A’.
Step 2
To calculate Dimension ‘I’ use the equation below.
Dim ‘I’ = Dim ‘A’ - (Dim ‘D’ + 5mm) mm
Step 3
*Add cabinetry thickness to Dimension ‘D’ and Dimension ‘I’ for final measurement before construction.