Westinghouse 6222900, 6223000, 6228600, 6225200, 6224900 Instruction Manual

Owner’s Manual

Indoor Lighting Fixture

Installation Instructions

W-101 091811

Please write model number here for future reference: / Veuillez noter le numéro de modèle aux fins de référence ultérieure: / Por favor, incluya el número del modelo aquí para futura referencia:

ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHT FIXTURE

Congratulations on your Westinghouse purchase. This fixture has been designed to give you many years of beauty and service. For questions and comments, please visit www.westinghouselighting.

com/contact-us.

NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any packing materials (see figure 1).

WARRANTY INFORMATION

This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for a period of Five Years from purchase date. This warranty is in lieu of all other

warranties expressed or implied.

This warranty does not cover acts of nature such as lightning damage, or corrosion and discoloration of components, nor does it cover damages caused through abuse, improper installation, surges in electric current, or acts of third parties.

This warranty does not cover costs of removing and re-installing the light fixture.

If this fixture fails for any reason covered by this warranty, simply return the fixture with a copy of the original sales receipt, freight prepaid and Westinghouse Lighting, at its option, shall repair or replace the fixture or refund the purchase price.

WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.

Read and follow instructions exactly as shown. If instructions are unclear, do not proceed. Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essential for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not damage electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are damaged, do not install fixture. Return to place of purchase.

For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are provided on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before 1985 have supply wires rated 60° C.

Consult a qualified electrician before installing.

NOTE: For fixture employing a grounded convenience outlet. This fixture employs a grounded type receptacle and is not intended for connection to a two wire ungrounded source of supply.

Applicable only to portable lamps:

To reduce the risk of electrical shock, all portable lamps have a polarized plug (one blade is wider than the other). This plug will fit into a polarized outlet only one way. If plug does not fit, reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord unless plug can be fully plugged into the extension cord. Do not alter the plug.

2

	FIGURE 1.	GROUND	*OUTLET
		WIRE
			BOX (B)
			WIRE
			CONNECTORS (O)
	SIDE
	HOLE (Q)
	MOUNTING		*OUTLET BOX
	BAR (A)
			SCREWS (C)
			LOCK WASHER (F)
	GREEN		HEX NUT (D)
			NIPPLE 1 (G1)
	GROUNDING

	SCREW (P)	SCREW
		COLLAR (M)
		CANOPY (N)
		SCREW COLLAR
		RING (L)
	CHAIN (K)
		FIXTURE LOOP (I)
		NIPPLE 2 (G2)
		COLUMN (J)
		HOLDER (S)

THUMB

SCREWS (T)

GLASS

SHADE (R)

BASE (H)

RETAINING

RING (U)

Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture.

*NOT SUPPLIED

3

MOUNTING AND WIRING INSTRUCTIONS

NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures meet all UL specifications.

1.Turn off power at circuit box to avoid possible electric shock.

2.Secure mounting bar (A) to outlet box (B) with outlet box screws (C) (not included) (see fig. 1).

3.Thread hex nut (D) onto nipple 1 (E1) approximately 1/4 inch and insert lockwasher (F), then thread nipple 1 (E1) onto mounting bar (A) and secure with hex nut (D).

4.Thread nipple 2 (G2) onto base (H) (carefully twist loop (I) to secure nipple 2 (G2) if needed). Do not twist or kinkwires.

5.Slide column (J) down over nipple 2 (G2).

6.Open one link on bottom end of chain (K). Attach to loop (I). Securely close link on chain (K).

7.Thread screw collar ring (L) onto screw collar (M), then place canopy (N) over top of screw collar (M).

8.Lace wires up through every other link on chain (K) then through screw collar (M) and nipple 1 (E1).

9.Open one link on top end of chain (K). Attach to loop on screw collar (M). Securely close link on chain (K).

10.Identify color coding of fixture wires (see fig. 2).

11.To connect wires, take black fixture wire (group A from fig. 3) and place evenly against black outlet box wire. Do not twist wires.

12.Fit wire connector (O from fig. 1) over wires and twist until there is a firm connection. If wire connector (O) easily comes off, reattach and check again for a firm connection.

13.Repeat steps 11 and 12 with the white (group B from fig. 3) fixture wires and outlet box wires.

14.Partially thread green grounding screw (P) into side hole (Q) on mounting bar (A)

15.Wrap ground wire from fixture around green grounding screw (P), leaving enough excess wire to then connect ground wire and outlet box wire with wire connector.

16.Tighten green grounding screw (P). Do not over tighten.

17.Tuckwires inside outlet box (B).

18.Remove screw collar ring (L) from screw collar (M).

19.Secure screw collar (M) to nipple 1 (E1).

20.Raise canopy (N) to ceiling and thread screw collar ring (L) to screw collar (M) and tighten as necessary.

FIXTURE ASSEMBLY INSTRUCTIONS

Warning: This fixture is for indoor use only.

1.Install lamp(s). Do not exceed recommended wattage.

2.Place glass shade(s) (R) into holder(s) (S) and secure with thumb screws (T) or retaining ring(s) (U), whichever is applicable. Do not over tighten.

3.Turn power back on at circuit box.

4