Welch Allyn PRO 4000 User Manual [en, es, fr]

0 (0)
Welch Allyn PRO 4000 User Manual

PRO 4000 Base Station

ThermoScan

ThermoScan

start

-

+12

V

 

 

 

Type 6021

English 4

Français 11

Español 18

Internet:

www.welchallyn.com

6-021-361/00/VII-07 USA / CDN / MEX

 

start

 

 

 

2

 

 

 

 

 

1

 

 

 

 

 

 

 

-

+

12

V

 

 

 

 

 

 

 

 

 

 

 

 

5

4

3

 

 

 

English

IMPORTANT SAFETY

INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:

Read all instructions before using this appliance.

DANGER

To reduce the risk of electric shock:

1.Do not reach for an appliance that has fallen into water. Unplug immediately.

2.Do not use while bathing or in a shower.

3.Do not place, store or charge the appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.

4.Unplug this appliance before cleaning.

SAVE THESE INSTRUCTIONS

4

WARNING

To reduce the risk of burns, fire, electric shock, or injury to persons:

1.Close supervision is necessary when this appliance is used by, on, or near children.

2.Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.

3.The appliance should never be exposed to temperatures of less than - 4 ºF/ - 20 ºC and more than 122 ºF/+ 50 ºC for longer than a few hours. Keep the appliance and cord dry at all times. Do not handle with wet hands.

Do not store in a damp environment. To avoid damage do not wind the cord around the appliance. It is important to check the cord for damage periodically particularly at each end where the cord enters the plug.

4.Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.

5.Keep the cord away from heated surfaces.

6.Never drop or insert any object into any opening.

7.Always attach plug to appliance first, then to outlet.

5

The Base Station of the PRO 4000 Thermometer provides charging and anti-theft function, as well as storage for the thermometer and the probe cover dispensers. Before use, read the use instructions carefully.

Warning

The base station is provided with a low-voltage adapter (Safety Extra Low Voltage Plug In Power Supply, type 5496). Therefore you must not exchange or manipulate any part of it. Otherwise there is risk of electric shock.

The Base Station must not be operated with the patients vicinity (4.92 ft/ 1.5 m)

Description

1Storage space for probe cover dispenser (PC 200)

2PRO 4000 Thermometer in its protective cover

3Low-voltage adapter

4Yellow charging indicator

5Green mains connection indicator

Package components

Braun ThermoScan Base Station

Use and Care Manual

1 rechargeable battery pack (NiMH)

1 set of screws and wall plugs

1 Low-voltage adapter

Additional items my be included as noted on outer packaging

Inserting the rechargeable batteries

The Base Station is supplied with 1 rechargeable battery pack. To make use of the charging function place the rechargeable battery pack in the battery compartment of the thermometer.

1

While other rechargeable batteries can be used in the thermometer, we do not recommend it as they can not be recharged in the Base Station.

To protect the environment, dispose of empty batteries according to national or local regulations.

6

Connecting

Connect the station with the mains only via the low voltage adapter. The green connection indicator will light up, showing that the station is ready for use.

Charging

When the PRO 4000 Thermometer is not in use it should be stored – in its protective cover – in the Base Station. When placed into the station, the thermometer will give a short beep and the yellow charging indicator will light up.

The yellow light indicates that the thermometer‘s batteries are charging. When the batteries are fully charged, the yellow light will go out. If it comes on again later on, this indicates that the batteries are being recharged to maintain their full capacity.

When in use, the thermometer’s display may show «RET» and the battery symbol. This means it has to be returned to the station for charging.

Care and Cleaning

Disconnect the Base Station from electrical outlet. Use a soft, dry cloth to clean the Base Station. Do not use abrasive cleaners. Never submerge this device in water or any other liquid. Store in a dry location free from dust and contamination and away from direct sunlight.

Anti-theft function

The PRO 4000 Thermometer is equipped with an anti-theft function which requires returning the thermometer to the Base Station within a pre-selected time. If this time is exceeded, the thermometer will be locked.

When leaving the factory, the anti-theft function of the PRO 4000 is turned off. Below are details to set the function and time period:

Put the thermometer into the station and wait for the long confirmation beep.

Press the start-button on top of the thermometer and keep it pressed while you take the thermometer out of the station.

7

When you release the start-button, the thermometer‘s display will show the actual anti-theft time setting. E.g. «H08» meaning 8 hours have been selected as the time for which the thermometer can be used before it has to be returned to the station.

To change the anti-theft interval setting, press the start button again and as often as necessary until the desired time is shown in the display.

«H--» means the anti-theft function is off, «H01» means 1 hour setting, etc.

Release the start button and place the thermometer back into the station within 30 seconds. A beep will sound, confirming the setting.

If the setting is not confirmed, repeat the procedure as described.

If the anti-theft function is enabled, and when not in the measuring process (stand-by mode) the thermometer will show the time remaining before the anti-theft function shuts down its operation. «H3.5» means the anti-theft function will shut down in 3.5 hours.

If the thermometer shows «RET» (without the battery symbol) on its display, the anti-theft time has elapsed and the thermometer must be returned to the station for unlocking.

If the anti-theft function is not enabled, the display will show «OFF» when in stand-by mode.

Product specifications

Long term storage ranges

Temperature:

–4 °F to 122 °F

 

(–20 °C to 50 °C)

Humidity:

95% non condensing

Shock:

withstands drop of 3 feet

Rechargeable Battery life: 3 years, 1000 charging

 

cycles

Battery capacity:

1 month standby,

 

500 measuring cycles

Rechargeable Battery type: customized dual battery pack (NiMH)

8

Loading...
+ 18 hidden pages