Weider PLATINUM 600 User Manual

5 (1)
Weider PLATINUM 600 User Manual

Model No. WESY68631

Serial No.

Write the serial number in the space above for future reference.

Serial Number Decal (under seat)

QUESTIONS?

As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if there are missing or damaged parts, we will guarantee complete satisfaction through direct assistance from our factory.

TO AVOID DELAYS, PLEASE CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE.

The trained technicians on our customer hot line will provide immediate assistance, free of charge.

CUSTOMER HOT LINE:

1-877-992-5999

Mon.–Fri., 6 a.m.–6 p.m. MST

 

USER’S MANUAL

CAUTION

 

Read all precautions and instruc-

Visit our website at

tions in this manual before

using this equipment. Save this

 

manual for future reference.

www.weiderplatinum.com

 

TABLE OF CONTENTS

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 UPPER CABLE ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 CABLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before beginning assembly.

WEIDER is a registered trademark of ICON Health & Fitness, Inc.

2

WARNING DECAL PLACEMENT

The decals shown here have been placed on the resistance system. If a decal is missing or illegible, please call our Customer Service Department tollfree at 1-877-992-5999, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time, to order a free replacement decal. Apply the decal in the location shown.

Keep hands and fingers clear of this area.

3

IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of serious injury, read the following important precautions before using the resistance system.

1.Read all instructions in this manual before using the resistance system. Use the resistance system only as described in this manual.

2.It is the responsibility of the owner to ensure that all users of the resistance system are adequately informed of all precautions.

3.The resistance system is intended for home use only. Do not use the resistance system in any commercial, rental, or institutional setting.

4.Use the resistance system only on a level surface. Cover the floor beneath the resistance system to protect the floor.

5.Make sure that all parts are properly tightened each time the resistance system is used. Replace any worn parts immediately.

6.Keep children under 12 and pets away from the resistance system at all times.

7.Keep hands and feet away from moving parts.

8.Always wear athletic shoes for foot protection while exercising.

9.The resistance system is designed to support a maximum user weight of 300 pounds.

10.The crossbar on the top frame is not designed to be used for pull-up exercises. Do not hang on the crossbar.

11.Pull on the lower cable only while sitting on the bench or standing on the base plate. Pull on the high cables only while sitting on the bench, with the seat in one of the three positions closest to the upright base, or while standing on the base plate.

12.The resistance system is designed to be used with the included resistance. Do not use the resistance system with any other type of resistance.

13.Always disconnect the lat bar from the high cables when performing an exercise that does not require it.

14.Make sure the storage knob is in place and fully tightened each time the resistance system is used.

15.Make sure that the cables remain on the pulleys at all times. If the cables bind as you are exercising, stop immediately and make sure that the cables are on the pulleys.

16.Do not pull on the cables while the resistance level is being adjusted.

17.If you feel pain or dizziness while exercising, stop immediately and begin cooling down.

WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.

4

BEFORE YOU BEGIN

Thank you for selecting the innovative WEIDER® PLATINUM 600 resistance system. The resistance system offers a selection of stations designed to develop every major muscle group of the body. Whether your goal is to tone your body, build dramatic muscle size and strength, or improve your cardiovascular system, the resistance system will help you to achieve the specific results you want.

For your benefit, read this manual carefully before using the resistance system. If you have questions

after reading this manual, please call our Customer Service Department toll-free at 1-877-992-5999, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number is WESY68631. The serial number can be found on a decal attached to the resistance system (see the front cover of this manual).

Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled.

ASSEMBLED

 

DIMENSIONS:

Crossbar

Height:

82 in.

 

Width:

66 in.

 

Depth:

80 in.

 

 

 

High Pulley

Console

 

Resistance Bar

 

 

Upright

 

 

Storage Knob

Foot Plate

 

 

Backrest

 

Low Pulley

Seat

 

Base Plate

 

 

Leg Lever

 

Seat Knob

 

 

 

 

5

ASSEMBLY

Make Things Easier for Yourself

This manual is designed to ensure that the resistance system can be assembled successfully by most people. However, it is important to realize that the versatile resistance system has many parts and that the assembly process will take time. Most people find that by setting aside plenty of time, assembly will go smoothly.

Before beginning assembly, carefully read the following information and instructions:

Assembly requires two persons.

Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.

For help identifying small parts, use the PART IDENTIFICATION CHART. Note: Some small parts may have been pre-attached for shipping. If a part is not in the parts bag, check to see if it has been pre-attached.

Tighten all parts as you assemble them, unless instructed to do otherwise.

As you assemble the resistance system, make sure all parts are oriented as shown in the drawings.

The included Allen wrenches and the following tools (not included) are required for assembly:

• Two adjustable wrenches

• One rubber mallet

• One standard screwdriver

• One Phillips screwdriver

Lubricant, such as grease or petroleum jelly, and soapy water.

Assembly will be more convenient if you have a socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches.

1.

Before beginning assembly, make sure that

1

 

 

 

 

 

 

 

 

 

 

 

 

 

you have read and understand the informa-

 

21

 

 

 

tion in the box above.

 

 

 

 

 

 

 

 

 

 

 

20

92

75

 

Attach a Wheel (21) to the Base (1) with a 3/8” x

 

 

 

 

104

 

75

 

3 1/2” Bolt (90), three 3/8” SAE Washers (75),

 

 

 

 

 

 

 

 

and a 3/8” Nylon Jamnut (92). Do not overtight-

 

 

 

 

 

en the Jamnut; the Wheel must be able to turn

 

 

 

 

 

easily.

 

 

20

21

 

 

 

 

 

 

 

 

 

90

 

Attach the other Wheel (21) to the Base (1) in

19

1

 

104

 

the same manner.

 

 

 

 

 

 

 

 

 

104

 

 

 

 

Attach two Plastic Feet (19) and two Large Plastic

 

 

 

 

 

Feet (20) to the Base (1) with four #8 x 3/4”

 

 

 

 

 

Screws (104).

 

 

 

 

6

2.Attach the Upright (3) to the Base (1) with two 3/8” x 2 3/4” Carriage Bolts (88), two 3/8” x 3” Bolts (87), and four 3/8” Nylon Locknuts (73) as shown. Note: This step will be easier to complete if the Upright and Base are tipped on their sides.

3.Attach the Foot Plate (4) to the Upright (3) with three 3/8” x 2 3/4” Carriage Bolts (88), three 3/8” SAE Washers (75), and three 3/8” Nylon Locknuts (73).

7

2

 

 

3

 

87

 

73

 

73

 

73

 

1

 

88

3

 

 

3

 

4

 

75

 

73

 

73

88

75

4. Insert the connector of the lower wire harness (A)

4

 

 

 

into the socket of the Upper Wire Harness (13).

 

 

 

 

 

 

 

The connector should slide easily into the

 

 

 

 

socket and snap into place. If the connector

 

 

 

 

does not slide easily and snap into place, turn the

 

 

6

78

connector over and then insert it.

 

13

 

 

 

 

Make sure that the connector and wire appear as

 

 

 

 

shown in the inset drawing. IF THE CONNEC-

 

3

A

 

TOR IS NOT INSERTED PROPERLY, THE CON-

 

 

 

 

SOLE MAY BE DAMAGED WHEN THE POWER

 

13

 

 

IS TURNED ON.

79

 

 

 

 

 

Pull the excess lower wire harness (A) out of

 

 

 

 

the Mech Assembly (6) and push it and the

 

 

 

 

Upper Wire Harness (13) into the Upright (3).

 

 

 

 

 

 

71

 

 

Insert the Mech Assembly (6) into the Base (1).

 

 

 

 

Attach the Mech Assembly to the Upright (3) with

 

 

 

 

a 1/2” x 3” Carriage Bolt (79) and a 1/2” Nylon

 

 

 

 

Locknut (78). Do not tighten the Locknut yet.

 

 

 

 

Attach the Mech Assembly (6) to the Base (1)

 

 

1

 

with the four M10 Nylon Locknuts (71).

 

 

 

 

 

 

 

Tighten the 1/2” Nylon Locknut (78).

 

71

 

A

 

 

13

 

 

 

 

 

5. Press the Front Leg Foot (29) onto the bottom of

5

 

 

 

the Front Leg (31). Note that the front of the

 

 

 

 

 

 

 

Front Leg Foot is taller than the back.

 

 

92

 

 

 

 

 

Attach the Leg Lever Bumper (30) to the Front

 

 

 

 

Leg (31) with a #8 x 3/4” Screw (104).

 

 

 

23

 

 

 

 

Attach the Bench Rail (23), with the hook on the

 

 

 

92

bottom, to the Front Leg (31) with two 3/8” x 2”

 

 

 

 

91

31

 

Carriage Bolts (91) and two 3/8” Nylon Jamnuts

 

 

 

 

 

(92).

 

 

 

 

 

 

104

 

 

 

 

31

 

 

 

 

Front

29

 

 

 

 

 

 

8

 

 

 

6. Grease a 3/8” x 4” Bolt (86) using the included

6

 

 

 

grease pack. Attach the Bench Rail (23) to the

 

 

 

 

 

 

3

Upright (3) with the Bolt and a 3/8” Nylon Jamnut

 

 

 

 

 

 

 

(92). Make sure the Bolt is inserted through

 

 

 

 

the indicated hole in the Bench Rail. Do not

 

 

 

 

overtighten the Jamnut; the Bench Rail must

 

 

 

 

be able to pivot easily.

 

 

26

 

Tighten the Storage Knob (26) into the Upright (3)

92

 

 

 

 

 

 

 

and the Bench Rail (23).

Hole

 

 

 

 

 

86

 

 

23

 

 

 

 

 

 

 

 

 

Grease

7. Grease a 3/8” x 2 3/4” Bolt (93). Orient the Leg

7

 

 

 

Lever (32) with the slot on the side shown. Attach

93

 

 

 

 

 

the Leg Lever to the Front Leg (31) with the Bolt

Grease

 

 

 

and a 3/8” Nylon Locknut (73). Do not overtight-

 

 

 

en the Locknut; the Leg Lever must be able to

 

 

 

 

pivot easily.

 

 

 

 

 

32

Slot

73

 

 

 

 

 

 

 

 

31

 

8. Pull out the Seat Knob (43) as far as it will go, and

8

 

48

 

set the Seat Carriage (48) on the Bench Rail (23).

 

 

 

 

 

Loosely attach two 8mm Metal Spacers (45), a

47

 

 

 

60mm Metal Spacer (44), and two Bearing

 

 

102

 

Wheels (46) to the center holes in the Seat

41

 

47

 

Carriage (48) with two M8 Flange Nuts (47) and

 

 

 

 

43

 

the M8 x 114mm Axle (102). Make sure that the

 

 

 

serrated edge of the Flange Nuts are against

 

 

 

 

the Seat Carriage.

23

 

 

 

 

 

 

 

While a second person presses down on the Seat

 

 

 

 

(41), hold the wheel assembly firmly against the

 

 

 

 

bottom of the Bench Rail (23) and properly tight-

 

 

 

 

en the M8 Flange Nuts (47). Make sure that

 

 

 

 

three threads are extending past the Nuts, and

 

 

 

 

that the wide sides of all six Bearing Wheels

 

 

 

 

(46) are pressed against the Bench Rail.

 

 

46

 

 

 

 

 

Engage the Seat Knob (not shown) into an

 

45

44

46

adjustment hole in the Bench Rail (23).

 

 

 

 

 

45

 

 

 

 

 

 

Wide

 

 

 

 

Side

 

 

9

Loading...
+ 18 hidden pages