Model No. WESY19512
Serial No.
Write the serial number in the space above for reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or find there are missing or damaged parts, we will guarantee you complete satisfaction through direct assistance from our factory.
TO AVOID DELAYS, PLEASE CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE. The trained technicians on our customer hot line will provide immediate assistance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference.
USER'S MANUAL
Visit our website at
www.weiderfitness.com
new products, prizes, fitness tips, and much more!
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 WEIGHT RESISTANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 TROUBLESHOOTING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 CABLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached to the center of this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before beginning assembly.
2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precautions before using the weight system.
1.Read all instructions in this manual and in the accompanying literature before using the weight system.
2.It is the responsibility of the owner to ensure that all users of the weight system are adequately informed of all precautions.
3.The weight system is intended for home use only. Do not use the weight system in any commercial, rental, or institutional setting.
4.Use the weight system only on a level surface. Cover the floor beneath the weight system to protect the floor.
5.Make sure all parts are properly tightened each time you use the weight system. Replace any worn parts immediately.
6.Keep children under 12 and pets away from the weight system at all times.
7.Keep hands and feet away from moving parts.
8.Always wear athletic shoes for foot protection.
9.The weight system is designed to support a maximum user weight of 300 pounds.
10.Always stand on a foot plate when performing an exercise that could cause the weight system to tip.
11.Never release the press arm, butterfly arms, leg lever, lat bar, or nylon strap while weights are raised. The weights will fall with great force.
12.Make sure that the cables remain on the pulleys at all times. If the cables bind while you are exercising, stop immediately and make sure that the cables are on all of the pulleys.
13.Always disconnect the lat bar from the weight system when performing an exercise that does not use the lat bar.
14.If you feel pain or dizziness at any time while exercising, stop immediately and begin cooling down.
15.The decals shown below have been placed on the weight system in the locations shown on page 4. If a decal is missing or illegible, call our toll-free Customer Hot Line at 1-800-999-3756 and order a free replacement decal. Apply the decal in the location shown.
Keep hands and fingers clear of this area.
Decal 2
Decal 1
WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
3
BEFORE YOU BEGIN
Thank you for selecting the versatile WEIDER® 8525 weight system. The weight system offers a selection of weight stations designed to develop every major muscle group of the body. Whether your goal is to tone your body, build dramatic muscle size and strength, or improve your cardiovascular system, the weight system will help you to achieve the specific results you want.
For your benefit, read this manual carefully before using the weight system. If you have additional questions, please call our Customer Service Department
toll-free at 1-800-999-3756, Monday through Friday,
6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number is WESY19512. The serial number can be found on a decal attached to the weight system (see the front cover of this manual).
Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled.
ASSEMBLED |
|
|
DIMENSIONS: |
|
|
Height: |
76 in. |
|
Width: |
37 in. |
High Pulley Station |
Length: |
44 in. |
|
Lat Bar
Butterfly Arms
Decal 1
Right Side
Backrest
Left Side
Preacher Pad |
|
Decal 2 |
Press Arm |
|
Seat |
|
Weight Stack |
Leg Lever |
|
Foot Plate |
Low Pulley Station |
|
|
|
Note: The terms “right side” and “left side” |
|
are determined relative to a person sitting |
|
on the seat; they do not correspond to right |
|
and left on the drawings in the manual. |
4
ASSEMBLY
Make Things Easier for Yourself
Everything in this manual is designed to ensure that the weight system can be assembled successfully by anyone. However, it is important to realize that the weight system has many parts and that the assembly process will take time. Most people find that by setting aside plenty of time, assembly will go smoothly.
•Assembly requires two people.
•Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.
•Tighten all parts as you assemble them, unless instructed to do otherwise.
•As you assemble the weight system, make sure all parts are oriented as shown in the drawings.
•For help identifying small parts, use the PART IDENTIFICATION CHART at the center of this manual.
The following tools (not included) are required for assembly:
• Two adjustable wrenches
• One rubber mallet
• One standard screwdriver
• One Phillips screwdriver
•Lubricant, such as grease or petroleum jelly, and soapy water.
Assembly will be more convenient if you have a socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches.
Frame Assembly |
1 |
|
|
|
3 |
1. |
|
Before beginning assembly, make sure that |
|
you have read and understand the informa- |
|
tion in the box above. |
4 |
|
|
For help identifying small parts, use the |
|
PART IDENTIFICATION CHART in the cen- |
|
ter of this manual. |
|
|
1 |
Press two 2” Square Outer Caps (51) onto the |
|
ends of the Stabilizer (5). Press a 2” Square Inner |
27 |
Cap (27) into the end of the Base (4). |
51 |
Insert two 5/16” x 2 3/4” Carriage Bolts (14) up |
5 |
|
|
through the Stabilizer (5). Insert two 5/16” x 2 1/2” |
|
Carriage Bolts (1) up through the Base (4). Note: |
|
It may be helpful to place a piece of tape over |
14 |
the bolt heads to hold the Bolts in place. |
|
|
51 |
Attach the indicated end of the Base (4) to the |
|
Stabilizer (5) with two 5/16” x 2 3/4” Carriage |
|
Bolts (14) and two 5/16” Nylon Locknuts (3). Do |
|
not tighten the Locknuts yet. |
|
5
2.Press a 1” Square Inner Cap (65) into the Front Upright (42).
Slide the Front Upright (42) onto the 5/16” x
2 1/2” Carriage Bolts (1) in the Base (4). Hand tighten two 5/16” Nylon Locknuts (3) onto the Carriage Bolts. Do not tighten the Locknuts yet.
3.Attach the two Weight Guides (62) inside of the Stabilizer (5) with two 5/16” x 2 3/4” Bolts (11), two 5/16” Washers (8), two 1/2” x 17/32” Spacers (61), and two 5/16” Nylon Locknuts (3).
Tighten the 5/16” Nylon Locknuts (3) used in step 1.
Slide two Weight Bumpers (19) onto Weight Guides (62). Stack the six Weights (25) on the Weight Bumpers (19). Make sure that all of the
Weights are turned so the large pin grooves are on the bottom of the Weights and on the same side of the weight stack.
Press the Weight Tube Bumper (64) into the end of the Weight Tube (63). Insert the Weight Tube into the stack of Weights (25). Make sure that the pins on the Weight Tube are resting in the pin grooves in the upper Weight.
Lubricate the insides of the holes in the Top Weight (76). Set the Top Weight onto the stack of Weights (25).
2
42
65
3
4
1
3
62
76
Lubricate
|
Pin |
63 |
|
|
|
Pin |
|
64 |
Groove
25
Pin
Groove
8 11
19
8
61
5
3
6
4.Press two 2” Square Inner Caps (27) into the indicated ends of the Top Frame (55). Press two
1 3/4” Square Inner Caps (44) into the ends of the crossbar on the Top Frame. Press two Round Inner Caps (78) into the top of the crossbar.
5.Attach the Top Frame (55) to the Front Upright (42) with two 5/16” x 2 3/4” Bolts (11), two 5/16” Washers (8), and two 5/16” Nylon Locknuts (3).
Attach the upper ends of the Weight Guides (62) to the Top Frame (55) with a 5/16” x 6” Bolt (60) and a 5/16” Nylon Locknut (3).
Tighten the 5/16” Nylon Locknuts (3) used in steps 2 and 5.
Arm Assembly
6.Press two 1” x 7/8” Plastic Bushing (75) onto the welded spacers on the Press Frame (17). Slide the Press Frame into place on the Base (4) as shown. Note: This will be a tight fit. The Plastic
Bushings should fit onto each end of the indicated tube in the Base.
Lubricate the 3/8” x 8” Bolt (59) with grease. Attach the Press Frame (17) to the Base (4) with the Bolt and a 3/8” Nylon Locknut (21). Do not overtighten the Locknut; the Press Frame must be able to pivot easily.
7.Press a 1 3/4” Square Inner Cap (44) into the top of a Press Arm (46). Press two 1” Round Inner Caps (49) into the ends of the handle on the Press Arm.
Attach the Press Arm (46) to one side of the Press Frame (17) with two 5/16” x 2 1/2” Bolts (22) and two 5/16” Nylon Locknuts (3).
Assemble the other Press Arm (46) in the same manner.
7
4 |
|
55 |
27 |
|
78 |
||
|
|
||
|
44 |
|
|
27 |
Crossbar |
44 |
|
5 |
11 |
|
|
|
|
|
|
|
|
8 |
|
|
8 |
|
|
|
55 |
|
|
|
|
3 |
|
|
|
|
60 |
|
3 |
|
|
|
42 |
|
62 |
6 |
|
|
|
|
17 |
|
|
|
21 |
|
|
Welded |
|
|
|
Spacer |
|
|
|
|
75 |
|
Lubricate |
|
4 |
|
59 |
|
|
Tube |
|
|
|
|
|
7 |
44 |
|
|
49 |
|
|
|
|
49 |
|
|
|
46 |
|
46 |
|
|
22 |
|
|
3 |
|
|
|
17 |
|
|