User’s manual
Accessory handset
for use with VTech models CS6219/CS6219-2/CS6219-3/ CS6219-4/CS6228-3/CS6228-6/ CS6229/CS6229-2/CS6229-3/ CS6229-4/CS6229-5
w w w.v t e c h p h o n e s . c o m
Model: CS6209
Congratulations
on purchasing your new VTech product. Before using this telephone, please read the Important safety instructions on page 7 of this manual.
This manual has instructions for setup and registration of your new handset. For full instructions on using the handset, see the user’s manual that came with your telephone base.
If you cannot find your user’s manual, you can view or download it at www.vtechphones.com.
For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com. In Canada, please visit www.vtechcanada.com.
Compatible with Hearing Aid T-Coil
T
TIA-1083
The ENERGY STAR® program (www.energystar.gov) recognizes and encourages the use of products that save energy and help protect our environment. We are proud to mark this product with the ENERGY STAR® label indicating it meets the latest energy efficiency guidelines.
Telephones identified with this logo have reduced noise and interference when used with most T-coil equipped hearing aids and cochlear implants. The TIA-1083 Compliant Logo is a trademark of the Telecommunications Industry Association. Used under license.
Table of contents |
|
Getting started.................................... |
1 |
Parts checklist....................................... |
1 |
Battery installation and charging.......... |
2 |
Add and register a handset................... |
3 |
Replace a handset................................ |
4 |
Handset layout...................................... |
5 |
Appendix............................................. |
6 |
Battery................................................... |
6 |
Important safety instructions................ |
7 |
Operating range.................................... |
8 |
Maintenance......................................... |
8 |
About cordless telephones................... |
9 |
The RBRC® seal................................... |
9 |
Warranty............................................. |
10 |
FCC, ACTA and IC regulations........... |
12 |
Technical specifications...................... |
14 |
ii
Getting started
Parts checklist
Your telephone contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary.
Battery compartment cover |
Battery |
Charger adapter |
Handset |
Charger |
User’s manual |
To purchase a replacement battery or a power adapter, visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
Getting started
Battery installation and charging
Install the battery as shown below. After installing the battery, you might be able to make and receive short calls. For best performance, charge the
handset for at least 16 hours before use. When not in use, place the handset in the telephone base or charger. See page 6 for battery operating times.
|
Battery indicators |
Battery status |
Action |
|||
|
The screen is blank. |
Battery has no charge and |
Charge until the screen shows |
|||
|
|
|
|
|
the handset cannot be |
LOW BATTERY (at least 10 |
|
|
|
|
|
used. |
minutes). |
|
The screen shows |
Battery has very little |
Charge until the screen shows |
|||
|
PLACE IN CHARGER |
charge and the handset |
LOW BATTERY (about four |
|||
|
and |
|
flashes. |
cannot be used. |
minutes). |
|
|
|
|
|
|
|
|
|
The screen shows |
Battery has enough charge |
Charge until the screen shows |
|||
|
LOW BATTERY, |
to be used for a short time. |
HANDSET X (about one hour). |
|||
|
|
flashes, and the |
|
|
||
|
handset beeps. |
|
|
|||
|
The screen shows |
Battery is charged. |
To keep the battery charged, |
|||
|
HANDSET X. |
|
place it in the telephone base |
|||
|
|
|
|
|
|
or charger when not in use. |
1.If the battery compartment cover is on the handset, press the indentation and slide the cover to remove.
2.Plug the battery securely into the plug inside the handset battery compartment, matching the color-coded label.
3.Place the battery with the label THIS SIDE UP facing up and the wires inside the battery compartment.
4.Align the cover flat against the battery compartment, then slide it towards the center of the handset until it clicks into place.
5. Charge the handset by placing it in the telephone base or charger. The CHARGE light is on when the handset charges.
1 |
2 |
3 |
4 |
5 Charge light |
When the screen shows LOW BATTERY, the backlight is off.
If the handset will not be used for a long time, disconnect and remove the battery to prevent possible leakage.
To purchase replacement batteries, visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
Getting started
Add and register a handset
Each newly purchased handset (CS6209) must be registered to the telephone base (CS6219, CS6228 or CS6229) before use. When first purchased, each expansion handset shows NOT REGISTERED.
To make registration easier, read all of the instructions on this page before you begin. If the handset screen does not show LOW BATTERY or
HANDSET X, you will need to charge the handset for at least five minutes before registering to the telephone base.
To register a handset:
1.Place the unregistered handset in the telephone base or charger. If PRESS FIND HS 4 SEC ON BASE does not appear on the handset screen after
a few seconds, remove the handset and place it in the telephone base or charger again.
2. On the telephone base, press and hold FIND HANDSET for about four seconds (until the red IN USE light on the
telephone base turns on) and then release the button. The handset shows PLEASE WAIT...
and it takes about 10 seconds to complete the
registration. The handset shows HANDSET X REGISTERED (X represents the handset
number assigned) and you hear a beep when the registration completes.
When the registration is complete, the newly registered handset is assigned the next available handset registration number. For instance, if you already have HANDSET 1 and HANDSET 2, the next registered handset is HANDSET 3.
If the registration fails, the handset shows NOT REGISTERED. To reset the handset, remove the handset from the telephone base or charger and place it back in. Try the registration process again.
You cannot register a handset if any other system handset is in use. Only one handset can be registered at a time.