Vtech SN1197, SN6127, SN1196, SN6187, SN6196 User Manual

1

User’s manual

SN6107

DECT 6.0 accessory handset

for use with VTech models

SN1157/SN1196/SN1197/SN6127/

SN6146/SN6147/SN6187/SN6196/

SN6197

Congratulations

on purchasing your new VTech product. Before using this

telephone, please read Important safety instructions on

page 9 of this manual.

This manual has instructions on how to set up and register

your new handset. For complete instructions on using the

handset, see the Abridged user’s manual that came with

your telephone base.

You may also view or download the online

Complete user’s manual for a full set of installation

and operation instructions at www.vtechphones.com.

In Canada, visit www.vtechcanada.com.

The ENERGY STAR

®

program (www.energystar.gov)

recognizes and encourages the use of products

that save energy and help protect our environment.

We are proud to mark this product with the

ENERGY STAR

®

label indicating it meets the latest

energy efficiency guidelines.

Telephones identified with this logo have reduced

noise and interference when used with most T-coil

equipped hearing aids and cochlear implants.

The TIA-1083 Compliant Logo is a trademark of

the Telecommunications Industry Association.

Used under license.

T

Compatible with

Hearing Aid T-Coil

TIA-1083

CareLine

™

Register online to get an additional 3-month warranty!

Visit www.vtechphones.com.

Registration

Register your product online for enhanced warranty

support.

Product news

Learn about the latest VTech products.

BC

2

Parts checklist

Your telephone package contains the following items. Save

your sales receipt and original packaging in the event

warranty service is necessary.

Cordless handset Handset charger and

charger adapter

Battery compartment cover

Battery

User’s manual

Handset battery installation

Plug the battery connector

securely into the socket.

1. Place the battery with

the label THIS SIDE UP

facing up and the wires

inside the battery

compartment.

2.

Slide the battery compartment cover towards the center

of the handset until it clicks into place.

3.

User’s manual

3

Handset charger installation

Electrical outlet

not controlled by

a wall switch

Handset charger

power adapter

Install the charger

as below.

1. Place the handset in

the handset charger

to charge.

2.

Handset battery charging

Once you have installed the battery, the handset indicates

the battery status. If necessary, place the handset in the

handset charger to charge. The battery is fully charged

after 11 hours of continuous charging.

Battery indicators Battery status Action

The screen is blank,

or displays Place

in charger and

flashes.

The battery has no

or very little charge.

The handset cannot

be used.

Charge without

interruption (about

30 minutes).

The screen displays

Low battery and

flashes.

The battery has

enough charge to be

used for a short time.

Charge without

interruption (about

30 minutes).

The screen displays

HANDSET X.

The battery is

charged.

To keep the

battery charged,

place it in the

handset charger

when not in use.

4

Add and register a handset

You can add new handsets to your telephone system. Each

handset must be registered with the telephone base before

use. When first purchased, each expansion handset shows

To register HS, see manual. The new handset should be

charged without interruption for at least 30 minutes before

registering it to the telephone base.

Make sure the handset is out of the handset charger and is

put near the telephone base. Make sure the handset shows

To register HS, see manual before you begin registration.

To register a handset to your SN1157/SN1196/SN1197/

SN6146/SN6147/SN6196/SN6197 telephone base:

Press MENU on the telephone base

when idle.

Scroll to Settings, then press SELECT.

Scroll to Registration, then press

SELECT. The telephone base shows

Registering... Please wait.

Press QUIET

#

on the cordless

handset. The handset shows

Registering... Please wait. Then

HANDSET X Registered appears on

the cordless handset and the telephone

base, and both devices beep. The handset is now

registered with the telephone base. It takes up to

60 seconds to complete registration.

If registration fails, the telephone base displays

Registration failed and you hear an error tone.

Start again from Step 1 above.

To register a handset to your SN6127/SN6187

telephone base:

Put the handset into the telephone

base. The base IN USE light turns

solid red. The handset shows

Registering... Please wait. Then

HANDSET X Registered appears on

the cordless handset. The handset

beeps and is now registered with

the telephone base. It takes up to

60 seconds to complete registration.

If registration fails, the handset displays Registration failed

and you hear an error tone. Start again from Step 1 above.

1.

2.

3.

4.

•

5

Deregister devices

If you want to replace a device, or reassign the designated

device number of a registered device, you must deregister

all devices that are registered to the telephone base. Then

register each device individually.

To deregister all devices from your SN1157/

SN1196/SN1197/SN6146/SN6147/SN6196/SN6197

telephone base:

Press and hold FIND HS at the side of the telephone

base for about 10 seconds until the telephone base

shows Registering... Please wait followed by

Deregister all devices?, then release FIND HS.

Immediately press YES or FIND HS.

All handsets show To register HS, see manual. The

deregistration process takes about 10 seconds to complete.

To deregister all devices from your SN6127/SN6187

telephone base:

Press and hold /FIND HANDSET at the side of the

telephone base for about 10 seconds until the telephone

base IN USE light turns solid red and then flashes red,

then release /FIND HANDSET.

Immediately press /FIND HANDSET.

All handsets show To register HS, see manual. The

deregistration process takes about 10 seconds to complete.

You cannot deregister all devices if any system device is

in use.

1.

2.

3.

1.

2.

3.