Vollrath 15000, 15001, 15002, 15003, 15005 Installation Manual

...
0 (0)

Operator’s Manual

InstaCut3.5 Slicer, Dicer, Wedger and Corer

Thank you for purchasing this Vollrath equipment. Before operating the equipment, read and familiarize yourself with the following operating and safety instructions. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Save the original box and packaging. Use this packaging to ship the equipment if repairs are needed.

SAFETY PRECAUTIONS

To ensure safe operation, read the following statements and understand their meaning. This manual contains safety precautions which are explained below. Please read carefully.

WARNING

Warning is used to indicate the presence of a hazard that will or can cause severe personal injury or death.

CAUTION

Caution is used to indicate the presence of a hazard that will or can cause minor or major personal injury if the caution is ignored.

NOTICE: Notice is used to note information that is important but not hazard-related.

To reduce risk of injury or damage to the equipment

Check the equipment before each use to insure it is clean.

Check for broken, nicked or dull blades and if found, replace the blade assembly.

Check to ensure the rubber bumpers are in place. DO NOT USE EQUIPMENT IF BUMPERS ARE NOT IN PLACE.

Check to insure that the pusher head sits down completely on the rubber bumpers.

On tabletop models the suction cups will hold the equipment securely to smooth surfaces.

Wall mounted equipment must be securely mounted to wall studs. Use proper size and type hardware to mount equipment to wall.

Guide rods must be lubricated using a light coating of mineral oil, Petrol-Gel, or food grade lubricant. DO NOT USE COOKING OIL AS IT WILL BECOME STICKY AND MAY PERMANENTLY DAMAGE THE PUSHER HEAD BEARINGS.

Tabletop

Wall Mount

 

 

Item No.

Item No.

Description

15000

15016

¼" Dice

 

 

 

15001

15017

³⁄" Dice

 

 

 

15002

15018

½" Dice

 

 

 

 

15003

15019

4

Section Wedge

 

 

 

 

15005

15021

6

Section Wedge

 

 

 

 

15006

15022

8

Section Wedge

 

 

 

15007

15023

10 Section Wedge

 

 

 

15008

15024

12 Section Wedge

 

 

 

 

15009

6

Section Core

 

 

 

 

15010

15026

8

Section Core

 

 

 

 

Installing the wall mounted model

1.Use four (4) ¼" screws of a suitable length to secure the base to the wall. Install screws into studs. If this is not possible, use proper anchors and screws to secure base.

FUNCTION AND PURPOSE

The InstaCut™ 3.5 manual food processor is intended for slicing, dicing, coring and wedging soft vegetables and fruits. It not intended to cut hard root vegetables such as carrots and sweet potatoes.

Register your product at Vollrath.com/registration and become eligible to win a free 10" Vollrath Tribute© fry pan.

© 2018 The Vollrath Company L.L.C.

Part No. 2350022-1 ml 6/28/18

Vollrath 15000, 15001, 15002, 15003, 15005 Installation Manual

FEATURES AND CONTROLS

A

 

B

 

C

 

F

D

 

 

G

E

 

F

H

I

 

Table Top Model

AGuide Rods. Guide and align the pusher head onto the blade set.

BHandle. Used to lower and raise the pusher head block

CBushings. Used for smooth and consistent operation of pusher head on the guide rods

DPusher Head Assembly. Consists of bushings, the pusher head and the pusher bock.

EBumpers. Cushions the stop of the pusher head.

B

J

 

C

 

F

D

 

G

A

 

E

E

H

F

I

 

Wall Mount Model

FThumbscrew. Used to secure the pusher head block or the blade assembly.

GPusher Head Bock. Pushes the food product through the blade assembly. Specifically sized to match the corresponding blade assembly.

HBlade Assembly. Houses the blades. Specifically sized to match the corresponding pusher head block

I Base Assembly. Holds the guide rods and blade assembly.

J Locking Pin. Secures the pusher head to the handle.

BEFORE FIRST USE

Clean the equipment. See the Cleaning section of this manual.

OPERATION

WARNING

Sharp Blade Hazard

Blades are sharp and can cause cuts. To avoid injury from sharp blades, handle with caution.

\

1. Check that the equipment is clean and the blades are in good condition and bumpers are in place. If loose or broken blades are found, replace the blade assembly.

2. Verify the bumpers are in place on the guide rods. DO NOT USE EQUIPMENT IF BUMPERS ARE NOT IN PLACE.

3. Place the equipment on a clean, flat work surface.

4. Check for proper blade alignment by slowly setting the pusher head onto the blade assembly. They should slide together with no obstructions. If there are obstructions, verify they are a matching set. Remove the obstruction.

5. Verify that the blade assembly and pusher block are the desired size.

6. Prepare the food product to be processed. The maximum size of the food product is 3½" (8.9 cm) in diameter.

7. Lift the handle and place the food on the blade assembly with the flat side down.

8.Remove hand from the blade assembly area and place that hand on the leg of the base on table top equipment, or on the wall for wall mounted models.

9.Using a strong, quick, downward thrust, force the food product through the blade assembly.

10.Repeat this process until you have prepared enough food product for your daily needs.

11.Clean and lubricate your equipment immediately after each use. See the Cleaning section of this manual for more information.

2

InstaCut3.5 Slicer, Dicer, Wedger and Corer Operator’s Manual

CLEANING

WARNING

Sharp Blade Hazard

Blades are sharp and can cause cuts. To avoid injury from sharp blades, handle with caution.

NOTICE: Food acids will dull the blades and corrode the metal. Always clean this food preparation equipment immediately after every use.

NOTICE: Do not put this equipment in a dishwasher or dish machine with soaps, detergents, or other alkaline chemicals that can harm the equipment.Handwash only.

NOTICE: Do not use abrasive materials, scratching cleansers or scouring pads to clean this equipment. These can damage the finish.

Disassemble

1.Remove the pusher head assembly:

Table top models. Slide the pusher head off the guide rods. Wall mount models. Remove the locking pin. Lift the handle and

slide the pusher head off the guide rods. Place the locking pin back into the hole on the handle assembly to prevent it from being lost.

2.Remove the two thumbscrews and

separate the pusher block from the pusher head.

3. Raise the bumpers approximately 2"

(5.0 cm).

4.Loosen the thumbscrew and carefully remove the blade assembly.

Wash

1.Wipe, rinse or spray off equipment, pusher head and blade assembly thoroughly with HOT water.

2.Do not wipe across the blades.

NOTICE: Wiping across the sharp edge of the blade can cause injury and will dull the blades.

3.Clean the blade assembly by forcing water, under pressure, through the blades from the unsharpened side. If necessary, use a nylon bristle cleaning brush to push food particles out from the unsharpened side of the blade assembly.

4.Let the equipment air dry.

Reassemble

1.Install the cutting blade assembly into the base. Tighten the thumbscrew to push blade assembly securely against the other side.

2.Lubricate the guide bar with mineral oil or Petrol-Gel.

NOTICE: Do not use cooking oil as it will become sticky and may permanently damage the equipment.

3.Slide the bumpers into place.

4.Reassemble the pusher head and pusher block together.

5.Install the pusher head assembly:

Table top models. Reassemble the pusher head assembly. Wall mount models. Remove the locking pin from its storage location on the handle assembly. Lift handle and slide the pusher

head on the guide rods. Place locking pin back into the hole through the handle assembly and the pusher head.

PREVENTATIVE MAINTENANCE

1.Clean the equipment after every use.

2.Use for intended purposes only.

3.Change the blades regularly – based on usage.

REPLACE THE BLADE ASSEMBLY

WARNING

Sharp Blade Hazard

Blades are sharp and can cause cuts. To avoid injury from sharp blades, handle with caution.

Wash new blades with warm, soapy water and rinse thoroughly to remove the thin protective oil film. Keep the sharp edge away from you when handling blades.

1.Familiarize yourself with the parts diagram for your equipment.

2.Remove the pusher head assembly:

Table top models. Slide the pusher head off the guide rods.

Wall mount models. Remove the locking pin. Lift handle and slide the pusher head off the guide rods. Place pin back into the hole on the handle assembly to prevent loss.

3.Raise the bumpers approximately 2" (5.0 cm).

4.Loosen thumbscrew and carefully remove the blade assembly. Remove the cutting blade assembly by pressing upwards on the bottom of the side of the blade holder, where the thumbscrew is located. Discard the old blade assembly.

5.Install the new cutting blade assembly by inserting the tab on the blade holder into the groove in the base, then lowering the blade holder into the seated and flush position in the base. Tighten the thumbscrew

6.Slide bumpers down guide rods to contact base assembly. Position pusher head assembly onto the guide rods, slowly lower pusher head assembly, and check pusher head block to blade alignment.

7.Lubricate the guide rods with mineral oil or Petrol-Gel after each use. Do not use cooking oil as it will become sticky and may permanently damage the equipment.

InstaCut3.5 Slicer, Dicer, Wedger and Corer Operator’s Manual

3

TROUBLESHOOTING

If the equipment no longer processes food cleanly or without damage to the food product, the blades could be dull and be in need of replacement. Broken, bent, or nicked blades must be replaced.

Problem

Might be Caused By

Course of Action

Broken Blade

Blades were dull.

Replace the blade assembly. Also inspect the pusher block. Replace if

damaged.

 

 

Pusher head does not slide

Guide rods improperly or insufficiently

Clean and lubricate the guide rides. See Cleaning.

easily.

lubricated.

 

Cuts poorly.

Blades are dull.

Replace blade assembly.

 

 

 

Cannot push food through.

Blades are misaligned or incorrect

Confirm the pusher block is correct for the blade assembly and that there

pusher block is installed.

is no interference between the pusher block and blade assembly.

 

SERVICE AND REPAIR

Serviceable parts are available on Vollrath.com.

To avoid serious injury or damage, never attempt to repair the unit or replace a damaged power cord yourself. Do not send units directly to The Vollrath Company LLC. Please contact Vollrath Technical Services for instructions.

When contacting Vollrath Technical Services, please be ready with the item number, model number (if applicable), serial number, and proof of purchase showing the date the unit was purchased.

WARRANTY STATEMENT FOR THE VOLLRATH CO. L.L.C.

This warranty does not apply to products purchased for personal, family or household use, and The Vollrath Company LLC does not offer a written warranty to purchasers for such uses.

The Vollrath Company LLC warrants the products it manufactures or distributes against defects in materials and workmanship as specifically described in our full warranty statement. In all cases, the warranty runs from the date of the end user’s original purchase date found on the receipt. Any damages from improper use, abuse, modification or damage resulting from improper packaging during return shipment for warranty repair will not be covered under warranty.

For complete warranty information, product registration and new product announcement, visit www.vollrath.com.

The Vollrath Company, L.L.C. Headquarters

Pujadas

Vollrath of China

Vollrath de Mexico S. de R.L. de C.V.

1236 North 18th Street

Ctra. de Castanyet,

Vollrath Shanghai Trading

Periferico Sur No. 7980 Edificio 4-E

Sheboygan, Wisconsin

132 P.O. Box 121

Limited

Col. Santa Maria Tequepexpan

53081-3201 USA

17430 Santa Coloma de Farners

Room 201, Building A

45600 Tlaquepaque, Jalisco |

Main Tel: 800-624-2051 or 920-457-4851

(Girona) – Spain

Xin Yi Plaza

Mexico

Main Fax: 800-752-5620 or 920-459-6573

Tel. +34 972 84 32 01

1618 Yi Shan Road

Tel: (52) 333-133-6767

Canada Customer Service: 800-695-8560

info@pujadas.es

Shanghai, 201103

Tel: (52) 333-133-6769

Tech Services: techservicereps@vollrathco.com

 

China, P.R.C.

Fax: (52) 333-133-6768

www.vollrath.com

 

Tel: +86-21-5058-9580

 

© 2018 The Vollrath Company L.L.C.

Part No. 2350022-1 ml 6/28/18

Loading...
+ 8 hidden pages