Vision Fitness T9450, T9300, T9500, T9700, T9350, T9200, T9600 User Manual

2.18 Mb
Loading...

TABLE OF CONTENTS

SECTION 1: MAINTENANCE PROCEDURE

MAINTENANCE CHECK LIST

TENSIONING THE BELT PROCEDURE

DECK RE-WAXING PROCEDURE

CLEAN THE GROOVES PROCEDURE

LUBRICATING THE AIR SHOCK PROCEDURE

SECTION 2: WIRING DIAGRAM

T9700 MCB NAME : MEB1J (WIRING DIAGRAM)

T9600/T9500 MCB NAME : MEA9J (WIRING DIAGRAM)

T9450/T9350/T9300/T9200/T9250 MCB NAME : JHT2.0(WIRING DIAGRAM)

SECTION 3: CONSOLE ENGINEERING MODE GUIDE

T9700 UCB NAME : DGB1J

T9600/T9500/T9450/T9350/T9300/T UCB NAME : DGA3J

T9200/T9250 UCB NAME : JHT

SECTION 4: MCB LED INSTRUCTIONS

MCB LED LAYOUT

MCB LED INDICATION

PWM MCB LED CHART

MCB LED TROUBLESHOOTING CHART

SECTION 5: TROUBLESHOOTING

NO DISPLAY ON CONSOLE

RUNNING SPEED IS NOT STABLE

TREADMILL STARTS TO RUN BY ITSELF

ALL OR SOME OF KEYS ON CONSOLE DO NOT WORK

NOISE GENERATED UNDER MOTOR COVER

TREADMILL WILL NOT START

INCLINE FUNCTION DOES NOT WORK

HEART-RATE-CONTROL FUNCTION DOES NOT WORK

Error Messages on the Console

SECTION 6 : SOFTWARE UPGRADE PROCEDURE

VISION SERIES TREADMILL SOFTWARE UPGRADE SOP

SECTION 1

MAINTENANCE PROCEDURE

PREVENTIVE MAINTENANCE SCHEDULE

 

 

 

 

 

 

 

 

 

 

 

 

VISION TREADMILL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Item

Daily

Weekly

Monthly

Quarterly

Biannual

Annual

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Console Mounting

 

 

 

 

Inspect

 

 

 

Bolts

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Frame

Clean

 

 

 

Inspect

 

 

 

 

 

 

 

 

 

 

 

 

Running Belt Top

 

Clean

 

 

Inspect

 

 

 

 

(Vacuum)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

#3 Carbon Brush

 

 

 

Inspect

 

Replace

 

 

 

 

 

 

 

 

 

 

 

Power Cord

 

 

Inspect

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Display Console

Clean

 

Inspect

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Handlebar

Clean

 

 

 

Inspect

 

 

 

 

 

 

 

 

 

 

 

 

Handrail &

 

 

 

Inspect

 

 

 

 

Handlebar

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Front Roller

 

 

 

Clean

Inspect

 

 

 

 

 

 

 

 

 

 

 

 

Rear Roller

 

 

 

 

Inspect

 

 

 

 

 

 

 

 

 

 

 

 

Emergency Button

Test

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Tension Wheel

 

 

Inspect

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V Belt

 

 

 

Clean

Inspect

 

 

 

 

 

 

 

 

 

 

 

 

Deck Re-waxing

 

 

Inspect &

 

 

 

 

 

 

 

Re-waxing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Running Belt

 

 

 

 

Inspect

 

 

 

 

 

 

 

 

 

 

 

 

Control Box

 

 

 

 

Clean

 

 

 

 

 

 

 

(Vacuum)

 

 

 

 

 

 

 

 

 

 

 

Motor

 

 

 

Clean

 

 

 

 

 

 

 

 

 

 

 

 

 

Air Shock

 

 

 

 

Lubricate

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1-1

 

 

 

 

TENSIONING THE BELT

Caution:

Over-tightening of the roller will severely shorten the life of the belt and may cause further damage to other components.

Running Belt:

If when you plant

your foot on the belt, you can feel a slipping

sensation then the belt has stretched and is slipping across the

rollers. This is a normal and common adjustment on a new treadmill. To eliminate this slipping, tension both the rear rollers Allen bolts 1/4 TURN as shown above. Try the treadmill again to check for slipping. Repeat if necessary, but

NEVER TURN the roller bolts more than 1/4 turn at a time.

Perfect Tension o f Running Belt: 0.9~1.1 lbs

Drive Belt:

If you have tensioned the running belt and are still experiencing a slipping, adjust the tension screw. Then try the treadmill again to check for slipping.

Perfect Tension of Drive Belt:

70~90 lbs

 

 

1-2

 

DECK RE-WAXING PROCEDURE

Frequency: Every 1 month.

LUBE

Name: DOW CORNING 350 SILICON

Procedure:

1.Loosen the tension bolts at both ends.

2.Pull the belt with your left hand and apply the silicon in the deck with your right hand. (The volume of silicon applied is about 25CC.)

3.Tighten the tension bolts.

4.Start the treadmill. Step on the treadmill belt to walk the silicon in. Adjust the belt tension if necessary.

5.With the clamp-on meter, measure the current draw of the motor. (Clamp

on either the red or the black wire.) The current should be less than 15Amps for 110V model. (less than 7.5Amps for 220V model.)

1-3

CLEAN THE GROOVES PROCEDURE

Frequency: Every 3 months.

Procedure:

1.Remove the drive belt and check the grooves in belt for dirt or dust and clean it.

2.Check the grooves in motor pulley for dirt or dust and clean it.

3Check the grooves in roller pulley for dirt or dust and clean it.

If dirty grooves in the drive belt, motor and roller pulley, there will be noises while running.

1-4

LUBRICATING THE AIR SHOCK

Frequency: Every 6 months.

Procedure:

1.Fold up the frame by using the deck-locking lever.

2.Add the lubricating oil on the shaft of the air shock.

3.Lift the frame up and down, repeating this several times to allow the lubricating oil blend into air shock.

1-5

SECTION 2

WIRING DIAGRAM INSTRUCTION

T9700(TM51D/E) MCB WIRING(FOR 110V / 220V)

T2

T1

 

T6

 

 

T8

 

 

T5

 

 

T7

 

 

T3

T4

VR1

T1-----Motor wire (black)

T2-----Motor wire (red)

T3-----D1 of on/off switch

T4-----D3 of on/off switch

T5-----20-pin console cable

T6-----Elevation cable

T7-----Speed sensor line

T8----- Ground wire

2-1

T9600HRT(COMFORT)/T9600HRT/T9500HRT/T9450HRT/T935

 

0/T9300 MCB WIRING(FOR 110V / 220V)

 

 

 

 

 

T2

T1

 

T6

 

 

 

 

 

T9

 

 

 

 

 

T7

T8

T5

T3

T4

VR1

 

 

 

T1-----Motor wire (black)

T2-----Motor wire (red)

T3-----D1 of on/off switch

T4-----D3 of on/off switch

T5-----8-pin console cable

T6-----Elevation cable

T7-----6-pin console cable

T8----- Speed sensor line

T9----- Ground wire

2-2

T9200/T9250 MCB WIRING(FOR 110V / 220V)

 

 

T2

T1

T9

 

 

 

T7

 

 

 

T8

 

 

 

T5

 

 

 

T6

T3

T4

VR1

 

T1-----Motor wire (black)

T2-----Motor wire (red)

T3-----D1 of on/off switch

T4-----D3 of on/off switch

T5-----8-pin console cable

T6-----Elevation cable

T7-----6-pin console cable

T8----- Speed sensor line

T9----- Ground wire

2-3

SECTION 3

CONSOLE ENGINEERING MODE GUIDE

+ 30 hidden pages