Viking VCIH56608BF, VCIH56608BW, VCIH56608AB, VCIH55408VC, VCIH55408SB Maintance Manual

Use & Care

Professional Indoor & Outdoor Hoods

VWH53012 / VWH53612

VWH53048 / VWH53648 / VWH54248

VWH54848 / VWH56048

VCWH53048 / VCWH53648 / VCWH54248

VCWH54848 / VCWH56048

VCIH53608 / VCIH54208 / VCIH55408 / VCIH56608

VBCV53638 / VBCV54238 / VBCV54838 / VBCV56038 / VBCV56038

VWHO3678 / VWHO4878 / VWHO6078 (Canadian Outdoor models not applicable)

2

Your purchase of a Viking Range hood attests to the importance you place upon the quality and performance of the major
appliances you use. With minimal care, as outlined in this guide, your new hood is designed to provide you with years of
reliable service. Please take a few minutes to learn about its proper and efficient use and care.

This guide will provide you with the information you need to become familiar with your hood’s care and operation.

Your complete satisfaction is our ultimate goal. If you have any questions or comments about this product, please contact
the dealer from whom you purchased it, or contact our Consumer Support Center at 1-888-845-4641.

We appreciate your choosing a Viking Range, LLC product, and hope that you will again select our products for your other
major appliance needs.

For more information about the complete and growing selection of products, visit us online at vikingrange.com

Congratulations

Table of Contents

Getting Started

B e f o r e U s i n g H o o d _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _______________2

Warnings ____________________________________________________________________________________3

Product Controls/Operation

S e t t i n g s a n d F u n c t i o n s _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _______________5

H o o d O p e r a t i o n _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _______________5

U s i n g O u t d o o r M o d e l s _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __5

Product Care

Cleaning and Maintenance _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ______________6

B a f f l e F i l t e r s _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ______________6

C h a r c o a l F i l t e r s _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ____________________ 7

H o o d C a n o p y _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ____________________ 7

Enamel Finish _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ______________7

Stainless Steel Finish _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ______________7

Ductless Venting Chamber _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ______________7

Light Bulbs _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ______________8

S e r v i c e I n f o r m a t i o n _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ______________9

W a r r a n t y _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ______________10

Before Using Hood

Although the hood is cleaned upon completion of the manufacturing process, you will probably need to clean your hood
again after installation. Wipe the surface of the hood with a good household cleaner applied with a soft cloth, or stainless steel
polish, depending on the finish of your hood. This will leave a protective finish on the hood.

3

WARNING

To reduce the risk of fire, electric shock, or injury when using
your unit, observe the following:

• Installation work and electrical wiring must be done by
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction.

• Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent back drafting. Follow the
heating equipment manufacturer’s guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), and the American Society
for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.

• When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.

• Ducted fans must always be vented to the outdoors.

• WARNING!: To reduce the risk of fire, use only metal
ductwork.

• CAUTION!: To reduce risk of fire and to properly exhaust
air, be sure to duct air outside. Do not vent exhaust air into
spaces within walls or ceilings, or into attics, crawl spaces,
or garages.

WARNING

To reduce the risk of fire, electric shock, or injury to persons,
observe the following:

• Use this unit only in the manner for which it is intended. If
you have any questions, contact the manufacturer.

• Before servicing or cleaning unit, switch power off at
service panel and lock service panel to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service
panel.

READ AND SAVE THESE INSTRUCTIONS

Warnings

WARNING

To reduce the risk of injury to persons in the event of a
rangetop grease fire, observe the following: (Based on
“Kitchen Firesafety Tips,” published by NFPA.)

1. SMOTHER FLAMES with a close fitted lid, cookie
sheet, or metal tray, then turn off the burner. BE
CAREFUL TO PREVENT BURNS. If the flames do not
go out immediately, EVACUATE AND CALL THE FIRE
DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN. You may be burned.

3. DO NOT USE WATER, including wet dishcloths or
towels a violent steam explosion will result.

4. Use an extinguisher ONLY if

• You know it is a Class ABC extinguisher, and
you already know how to operate it.

• The fire is small and contained in the area
where it started.

• The fire department is being called.

• You can fight the fire with your back to an
exit.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY
TO PERSONS, RANGEHOODS MUST BE INSTALLED WITH THE
VENTILATORS THAT ARE SPECIFIED ON THEIR CARTON
INDICATING SUITABILITY WITH THIS MODEL. OTHER
VENTILATORS CANNOT BE SUBSTITUTED.

TO REDUCE THE RISK OF A RANGETOP GREASE FIRE:

1. Never leave surface units unattended at high setting.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or
when cooking flaming foods. (i.e. Crepes suzette,
Cherries jubilee, Peppercorn beef flambé).

3. Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate
for the size of the surface element.

WARNING

4

CAUTION

DO NOT place flammable material on warming shelves
when using heat lamps.

CAUTION

Do not use a porcelain cleaner or rough abrasive cleaner.

CAUTION

Accessible parts may become hot when used with cooking

appliance.

- Children should be supervised to ensure that they do not
play with the appliance.

- This appliance is not intended for use by persons (including
children) with reduced physical sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appiance by a person responsible for their
safety.

CAUTION

Unplug power cords from control panel before cleaning or
servicing hood.

CAUTION

If the power to the hood is not disconnected during cleaning,
the heat sensor thermostat can cause the blower to turn on.

Warnings

CAUTION

For general ventilating use only.

- DO NOT use to exhaust hazardous or explosive materials
and vapors.

- DO NOT flambe under the hood.

CAUTION

This appliance is not to be used by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
the use of the appliance by a person responsible for their
safety. Children should be supervised to ensure that they
do not play with the appliance.

5

Hood Operation

Always turn on your hood before you begin cooking to establish airflow in the kitchen. Also let the blower run for a few
minutes to clear the air after you turn off your cooking appliance. This will help keep the kitchen air cleaner.

Indoor Hoods

ON/OFF - Blower speed knob—Starts and stops the blower. Push in on the
knob to allow it to pop out. Turn the knob clockwise to increase the blower
speed and counter clockwise to decrease speed. 0 is off, 1 is lowest speed,
and 5 is the highest speed. The type of cooking you are doing will dictate
the speed of the blower you use.

Light On/Off / Dimmer knob —Controls the 8-watt LED lights located in the
front of the hood. Push in on the knob to allow it to pop out. Turn the
knob clockwise to brighten the halogen lights and counter clockwise to
dim the lights.. O is off, 1 is dimmest and 5 is the brightest.

Heat lamp switches— Push to turn the heat lamps on and off.

Each professional 18” H. wall hood will be equipped with one or two heat
lamp outlets. The 250-watt infrared bulbs are not included and should be
purchased locally.

Settings and Functions

ON

OF F

ON

O

FF

Blower Speed Knob

LO LO HI HI

Dimmer Knob

LIGHTS

LO LO HI HI

FAN

Using Outdoor Hoods

• Outdoor hood models should be installed in a covered yet non-enclosed area. They should also be protected from natural

elements (such as rain) as much as possible.

• Always turn the outdoor hood on to the “HIGH” position before lighting the grill.

• Keep the grill canopy closed as much as possible when cooking so smoke is exhausted from the back of the grill. This allows
for optimum performance of the hood.

• During breezy conditions, outdoor hoods may not perform well.

Fan On/Off switch—Starts and stops the blower. When turned on the blower will operate at the previous setting of the speed
control.

Blower speed knob—Turn the knob counterclockwise to decrease the blower speed and clockwise to increase speed. The type
of cooking you are doing will dictate the speed of the blower you use.

Light switch—Controls the 50-watt halogen lights located in the front of the hood.

Dimmer knob—Turn the knob clockwise to brighten the halogen lights and counterclockwise to dim the lights.

Heat Lamp

On/Off

Heat Lamp

Indicator

Light

LED Light

Fan On/Off

Blower

Speed Knog

Light On/Off

Dimmer Knob

LED Light

6

Any piece of equipment works better and lasts longer when maintained properly and kept clean. Ventilation equipment
is no exception. Your hood must be kept clean and maintained properly.

Cleaning Baffle Filters

As air passes through a baffle filter, grease particles collect on the stainless steel U-shaped baffle channels and drip
down into the bottom of the filter. Baffle filters are extremely efficient when compared to mesh filters. The power of
the hood is increased as more air passes through a baffle filter than with mesh filters, which are usually dirty. Baffle
filters are almost universally required in commercial installations due to their superior ability to capture grease. The
baffle filters should be examined periodically to assure that all surfaces and parts are clean. The filters can be washed
in a dishwasher or in a sink with hot, soapy water. Simple periodic cleaning will ensure maximum filter effectiveness.

• Do not use caustic detergent to clean the filters. An abrasive or corrosive cleaner may damage the finish.

• Do not take the baffle filters apart to clean them. It is not necessary and will void the filter warranty.

CAUTION

Unplug power cords from control panel before cleaning or
servicing hood.

Slide filter forward off of rear lip. Lower filter rear,

then slide filter front out.

Slide filter forward off of rear lip. Lower filter rear, then

slide filter front out.

Cleaning and Maintenance

2

2

1

3

3

3

Remove the screws located on the side at the top

and bottom of each spacer and slide spacer forward

off of rear lip. Lower spacer rear, then slide spacer

front out.

When cleaning filters in 18”H. hoods, always remove the

grease trough and clean by soaking in a sink with hot

soapy water.

1

1

2

3

2

1

1

2

3

Grease Trough
(18” H. models only)

7

Maintaining Charcoal Filter (Recirculating Hoods Only)

Replace the charcoal filters every 6 months to 1 year depending on the amount and type of cooking
you do.

To replace, remove the baffle/charcoal filter assembly and slide the charcoal filter out of the channel and
replace with a new one. Do not put the charcoal filters in the dishwasher.

Replacement filters are available through your local Viking Range dealer, or you can call the Viking
Online Store at 1-877-834-8222 or visit vikingrange.com.

CAUTION

For general ventilating use only. DO NOT use to exhaust hazardous or
explosive materials and vapors.

Cleaning and Maintenance

Cleaning Hood Canopy

Finishes in enamel or stainless steel are highly resistant to damage or discoloration due to grease, steam, and heat—
provided that reasonable care is given to the equipment. The following suggestions will help keep your hood looking new.

1. Do not allow an excessive accumulation of grease. For best results, you should wipe your hood clean with a cloth dipped in
warm, soapy water. DO NOT USE ABRASIVE CLEANSERS, STEEL WOOL PADS, OR ABRASIVE CLOTHS. DO NOT use cleansers that
contain chlorides; the chlorides in the cleaner could damage the stainless steel finish. If you need to scrape stainless steel to
remove encrusted materials, first soak the area with hot towels to loosen the material, then use a wooden or nylon spatula or
scraper. DO NOT use a metal knife, spatula, or any other metal tool to scrape stainless steel.

2. Every 3 months give your hood a thorough cleaning. On painted surfaces, use a new coat of wax. A good wax cleaner—
available at either a grocery or hardware store—will do both jobs at once. On stainless steel surfaces, use a good stainless
steel cleaner and polish.

Renewing Enamel Finish

If discoloration occurs, you should thoroughly polish
the finish on your hood to renew its gloss and luster and to remove any grease residue which may have a yellowing effect.
Use any good enamel polish, refrigerator polish, or automotive polish.

Renewing Stainless Steel Finish

Regular cleaning is the best way to assure that your stainless steel finish stays bright and unscratched. Use lemon oil or
stainless steel polish to coat and protect stainless steel.

Cleaning Ductless Venting Chamber (Professional Hoods Only)

1. Remove the middle vent by gently raising up and pulling out.

2. Use the same cleaning directions as in “Cleaning the Hood Canopy” section.

3. After cleaning, replace the middle vent.

Replacing the Light Bulbs

When removing bulbs use an oven mitt to protect your hand in case the bulb breaks.

CAUTION

Do not use a porcelain cleaner or rough abrasive cleaner.

8

LED Lights - Indoor Models

1. Unscrew bulb.

2. Replace the bulb with a 120 volt, Phillips R20 8-watt LED bulb (8R20/F90 2700 DIM). Can be purchased locally.

Halogen Lights - Outdoor Hoods

1. Unscrew halogen bulb.

2. Replace the bulb with a 120 volt, 50-watt halogen bulb.

Infrared Heat Lamp

1. Unscrew infrared bulb from heat lamp socket.

2. Replace the bulb with an R40, 120 volt, 250-watt infrared bulb. (not included with product)

1

1

2

Cleaning and Maintenance

1

1

2

2

9

If service is required, call your authorized service agency.

Have the following information readily available.

• Model number

• Serial number

• Date purchased

• Name of dealer from whom purchased

Clearly describe the problem that you are having. If you are unable to obtain the name of an authorized service agency, or
if you continue to have service problems, contact Viking Range, LLC at 1-888-845-4641, or write to:

VIKING RANGE, LLC

PREFERRED SERVICE

111 Front Street

Greenwood, Mississippi 38930 USA

Record the information indicated below. You will need it if service is ever required. The model and serial number for your
hood is located behind the baffle filter on the left side panel in the lower right corner.

M o de l no. ____________________________________________________ Se ri al n o. __________________________________________________________

D a te of p ur c ha s e ____________________________________________ D at e in st a ll e d ____________________________________________________

D e al e r’s n am e ______________________________________________________________________________________________________________________

A d d r e s s ____________________________________________________________________________________________________________________________

______________________________________________________________________________________________________________________________________

If service requires installation of parts, use only authorized parts to ensure protection under the warranty.

THIS MANUAL SHOULD REMAIN WITH THE HOOD FOR FUTURE REFERENCE.

Service Information

10

Warranty

HOOD WARRANTY

TWO YEAR FULL WARRANTY

Hoods and all of their component parts, except as detailed below*, are warranted to be free from defective materials or
workmanship in residential housed hold use for a period of two (2) years from the date of original retail purchase. Viking
Range, warrantor, agrees to repair or replace at its option, any part which fails or is found to be defective during the
warranty period. Warranty service must be performed by a Viking Range LLC authorized service agency or
representative.

*90 Day Cosmetic Warranty: Products are warranted to be free from cosmetic defects in material or
workmanship for a period of 90 days from the date of original retail purchase. This warranty covers
manufacturing based defects only and does not cover issues resulting from handling or installation. Inspection
of the product should be made at time of delivery. Any defects must be reported to the selling dealer within
the 90 day period. Viking Range LLC uses the most up to date processes and the best materials available to
produce all color finishes. However, slight color variation may be noticed because of the inherent differences in
painted parts and porcelain parts as well as differences in product location and natural or artificial lighting.
Warranty service must be performed by a Viking Range LLC authorized service agency or representative.

*90 Day Residential Plus: Viking products are designed and certified for residential use only. They are not
intended for use in commercial applications. Viking products should only be used in accordance to national
and local codes. Viking is not responsible for property damage or injury resulting from use in a commercial
application. To support the manufacturing quality of its appliance’s Viking will provide a full 90 day warranty
for products used in “Residential Plus “applications. This “Residential Plus” warranty applies to applications
where use of the product extends beyond residential use but is in compliance with national and local code. In
some jurisdictions these applications are zoned as residential. Examples of, but not limited to, such
applications covered by this warranty are bed and breakfasts, fire stations, private clubs, churches,
condominium/apartment common areas etc. Under this "Residential Plus" warranty, the product, its
components and accessories are warranted to be free from defective material or workmanship for a period of
ninety (90) days from the date of original retail purchase. Viking Range, LLC, warrantor, agrees to repair or
replace, at its option, any part which fails or is found to be defective during the warranty period. This warranty
covers parts and labor. This warranty excludes use of the product in all commercial locations such as
restaurants, food service locations and institutional food service locations.

FIVE YEAR LIMITED WARRANTY

Any ventilator motor which fails due to defective materials or workmanship in normal residential use during the third
thru the fifth year from the date of original retail purchase will be repaired or replaced free of charge for the part itself,
with the owner paying all other costs, shipping, handling and labor. Aesthetic conditions such as corrosion, scratching,
discoloration, carbon/food build up or similar blemishes due to normal wear and tear or improper use or lack of
maintenance is excluded from this warranty.

WARRANTY TERMS

This warranty extends to the original retail purchaser of the product warranted hereunder and to each transferee owner
of the product during the term of the original purchaser’s warranty. The warranty is transferable by the original retail
purchaser via home sale only. If a transferee owner is unable to provide proof of purchase from the original purchaser
and the product has not been previously registered, the production date of the product, located in the serial number on
the product, will serve as the effective warranty start date.

The activation date of the warranty begins from the date of original retail purchase. In the case of new product
purchase via building development sales, activation begins from the earlier date of either certificate of occupancy or 24
months from date of manufacture. Note date of manufacture is identified by serial tag on product.

This warranty does not cover units purchased as b-stock, liquidation, salvage, seconds, refurbished, as-is, used products.

This warranty shall apply to products purchased in the United States and Canada. Products must be purchased in the
country where service is requested. Warranty service must be performed by a Viking Range LLC authorized service
agency or representative. Warranty shall not apply to damage resulting from abuse, accident, natural disaster, loss of
electrical power to the product for any reason, alteration, improper installation, improper operation, or repair service of
the product by anyone other than a Viking Range LLC authorized service agency or representative. This warranty does
not apply to commercial usage. Warrantor is not responsible for consequential or incidental damage whether arising
out of breach of warranty, breach of contract or otherwise. Some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations do not apply to you.

Owner shall be responsible for proper installation, providing normal care and maintenance, providing proof of purchase
upon request, and making the product reasonably accessible for service. If the product or one of its component parts
contains a defect or malfunction during the warranty period, after a reasonable number of attempts by the warrantor to
remedy the defects or malfunctions, the owner is entitled to either a refund or replacement, at the warrantor’s
discretion of the product or its component part or parts. Warrantor’s liability on any claim of any kind, with respect to
the goods or services covered hereunder, shall in no case exceed the price of the goods or service or part thereof which
gives rise to the claim.

WARRANTY SERVICE

Under the terms of this warranty, service must be performed by a Viking Range LLC authorized service agent or
representative. Service will be provided during normal business hours Labor performed at overtime or premium rates
shall not be covered by the warranty. To obtain warranty service contact Viking Range LLC Customer Care at 1-888-845-

4641. Please have model number, serial number, and date of original purchase available when calling. IMPORTANT:
retain proof of original purchase to establish warranty period. The return of the owner registration card is not a
condition of warranty coverage. You should, however, return the owner registration card so Viking Range LLC can
contact you should any question of safety arise which could affect you. Any implied warranties of merchantability and
fitness applicable to the above described burner assemblies, infrared rotisserie burners, grill grates, and stainless steel
parts are limited in duration to the period of coverage of the applicable express written limited warranties set forth
above. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitations may
not apply to you. This warranty gives you specific legal rights, and you may also have other rights which may vary from
jurisdiction to jurisdiction.

Specifications subject to change without notice.

11

F21286J EN (022820)

Viking Range, LLC

111 Front Street

Greenwood, Mississippi 38930 USA

[phone]

For product information

call 1-888-845-4641,

or visit the Viking Web site at vikingrange.com