Viking C-2000A, C-3000, C-4000, K-1900-3, K-1900-5 User Manual

The K-1705 Series entry phones provide a tough and
attractive handsfree phone for apartment, and resi­dential door entry or applications requiring a vandal
resistant speaker phone. The K-1705 Series entry
phones are available in two attractive finishes:
“brushed stainless steel” and “oil rubbed bronze”.

When the “Call” button is pressed, the K-1705-3
returns dial tone. The keypad may then be used to
dial any number. If no Touch Tone is entered within 8
seconds, CPC is detected, a busy signal is detected,
or the programmable maximum call time has elapsed,
the K-1705-3 will automatically disconnect. Alternatively, the K-1705-3 may be disconnected by pressing the “Call” button
again. The K-1705-3 comes complete with a standard, flush mount, rough-in box. In addition, an optional VE-6x7 weather
resistant, surface mount box is available.

For outdoor or harsh environments, the K-1705-3 is available with Enhanced Weather Protection (EWP). EWP products fea­ture rubber gaskets and boots, closed cell foam gasketing, hand soldered silicon sealed connections, anti-corrosive gel filled
butt connectors, as well as urethane encapsulated circuit boards with internally sealed, field-adjustable trim POTS and DIP
switches.

• Built-in high resolution color video camera with wide viewing,
tilt/swivel adjustments and wide operating temperature of

-30°F to 150°F

• Audio and video transmission on one CAT5E cable (page 5)

• Vandal Resistant Features: 14 gauge louvered stainless
steel faceplate with stainless steel speaker/mic screen, heavy
duty metal keypad and “Call” button, impact and scratch
resistant camera lens and hex drive mounting screws

• Weather Resistant Features: Mylar speaker, faceplate
gasket, mic and speaker gasket, internally sealed (IP67)
push button switch and keypad, sealed camera lens, potted
camera circuit board, stainless steel phone and camera
mounting hardware

• Available in 2 standard faceplate finishes: brushed stainless
steel or oil rubbed bronze

• Optional Enhanced Weather Protection (EWP), conforms to
NEMA requirements

• Yellow “in use” LED

• Telephone line powered

• Volume adjustments for microphone and speaker

• Advanced call progress detection: disconnects on busy
signal, return to dial tone, CPC, reorder tone, maximum call
time out and 40 second silence time out

• Selectable auto-answer feature for monitoring

• Selectable push button disconnect

• Zinc plated steel rough-in box with (2) 3/4” conduit knockouts

• Optional VE-6x7 Surface Mount Box available

• Microphone and speaker volume controls

• Selectable VOX switching speed

K-1705 Series

K-1705 Series

Video Entry Phones

with Keypads

May 16, 2008

PPrraaccttiicce

e

T

T

EELLEECCOOM

M

S

S

OOLLUUTTIIOONNSSFFOORRTTHHE

E

221

1

SST

T

C

C

EENNTTUURRY

Y

TECHNICAL

TECHNICAL

FFeeaattuurrees

s

PPhhoonnee......771155..338866..8888661

1

Dimensions: Overall: 140mm x 165mm x 66mm (5.5” x 6.5” x

2.6”) , Rough-in box: 114mm x 140mm x 64mm (4.5” x 5.5” x 2.5”)

Shipping Weight: 1.6 kg (3.5 lbs)
Operating Temperature: -34°C to 65°C (-30°F to 150°F)
Connections: Standard model: (3) gel-filled butt connectors (3M

Scotchlok UR2) and 2-position terminal block, EWP model: (5)
gel-filled butt connectors (3M Scotchlok UR2)

(See page 2 for complete specifications)

SSppeecciiffiiccaattiioonns

s

AApppplliiccaattiioonns

s

• Apartment entry phone when used with the K-1900-3
Apartment Entry Dialer or C-4000 Apartment/Office Entry

Controller or C-3000 Apartment Entry Controller

• Residential gate or door entry phone when used with the

C-2000A Door Entry Controller

• Courtesy and customer assistance phone

• Automated teller (ATM) phone

• Security or emergency phone

• Hot-Line phone when used with the K-1900-5 Hot-Line

Dialer

Note: When installing a line powered phone on a low
voltage and/or low loop current phone system extension, a TBB-1A
Talk Battery Booster may be required (Fax Back # 630).

• Kiosk phone with (100 number speed dialing) when used
with the K-1900-9 Multi-Number Dialer

Vandal Resistant Handsfree Entry

Phones with Built-In Keypad

K-1705-3 “Brushed Stainless Steel”

(similar to brushed nickel)

K-1705-3-BN “Oil Rubbed Bronze”

(satin dark brown powder paint

with fine copper metallic)

IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT, PLEASE CONTACT: VIKING TECHNICAL SUPPORT AT [phone]

Our Technical Support Department is available for assistance Monday 8am - 4pm and Tuesday through Friday 8am - 5pm central time. So that we can give you better service, before you call please:

1. Know the model number, the serial number and what software version you have (see serial label).

2. Have your Technical Practice in front of you.

3. It is best if you are on site.

RETURNING PRODUCT FOR EXCHANGE

The following procedure is for equipment that has failed out-of-box (within 10 days of purchase):

1. Customer must contact Viking’s Technical Support at 715-386-8666 to determine possible causes for the problem. The

customer MUST be able to step through recommended tests for diagnosis.

2. If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input
and troubleshooting, a Return Authorization (R.A.) number will be issued. This number is valid for fourteen (14)
calendar days from the date of issue.

3. After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your
distributor will then replace the product over the counter at no charge. The distributor will then return the product to
Viking using the same R.A. number.

4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't
followed the steps listed in 1, 2 and 3, be aware that you will have to pay a restocking charge.

RETURNING PRODUCT FOR REPAIR

The following procedure is for equipment that needs repair:

1. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA)

number. The customer MUST have a complete description of the problem, with all pertinent information regarding the
defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc.

2. Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static
sensitive equipment such as a circuit board should be in an anti-static bag, sandwiched between foam and individual­ly boxed. All equipment should be wrapped to avoid packing material lodging in or sticking to the equipment. Include
ALL parts of the equipment. C.O.D. or freight collect shipments cannot be accepted. Ship cartons prepaid to:

Viking Electronics, 1531 Industrial Street, Hudson, WI 54016

3. Return shipping address: Be sure to include your return shipping address inside the box. We cannot ship to a PO Box.

4. RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.

the necessary modifications to maintain uninterrupted service.
If trouble is experienced with the K-1705-3, for repair or warranty information, please contact:

Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI 54016 [phone]

If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the
equipment until the problem is resolved.

Connection to Party Line Service is subject to State Tariffs. Contact the state public utility commission, public service com­mission or corporation commission for information.

WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR) MAKING TEST CALLS TO EMERGENCY NUMBERS:

Remain on the line and briefly explain to the dispatcher the reason for the call. Perform such activities in the off-peak
hours, such as early morning or late evenings.

It is recommended that the customer install an AC surge arrester in the AC outlet to which this device is connected. This
is to avoid damaging the equipment caused by local lightning strikes and other electrical surges.

PART 15 LIMITATIONS

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communica­tions. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.

FCC REQUIREMENTS

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. Inside the front panel
of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX.
If requested, this number must be provided to the telephone company.

The REN is used to determine the number of devices that may be connected to a telephone line. Excessive REN's on a
telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of
the REN's should not exceed five (5.0) To be certain of the number of devices that may be connected to a line, as deter­mined by the total REN's, contact the local telephone company. For products approved after July 23, 2001, the REN for
this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.

The plug used to connect this equipment to the premises wiring and telephone network must comply with the applicable
FCC Part 68 rules and requirements adopted by the ACTA. If your home has specially wired alarm equipment connected
to the telephone line, ensure the installation of this K-1705-3 does not disable your alarm equipment. If you have ques­tions about what will disable alarm equipment, consult your telephone company or a qualified installer.

If the K-1705-3 causes harm to the telephone network, the telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the cus­tomer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is nec­essary.

The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the
operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make

LIMITED WARRANTY

Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of one year from the date of purchase from any authorized Viking distributor or 18 months from the date manu­factured, which ever is greater. If at any time during the warranty period, the product is deemed defective or malfunctions, return the product to Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016. Customer must contact Viking's
Technical Support Department at 715-386-8666 to obtain a Return Authorization (R.A.) number.

This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, negligence or any damage caused by use of the product by the purchaser or others.

NO OTHER WARRANTIES. VIKING MAKES NO WARRANTIES RELATING TO ITS PRODUCTS OTHER THAN AS DESCRIBED ABOVE AND DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTIES OR MERCHANTABILITY OR FIT-

NESS FOR ANY PARTICULAR PURPOSE.

EXCLUSION OF CONSEQUENTIAL DAMAGES. VIKING SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE TO PURCHASER, OR ANY OTHER PARTY, FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL OR EXEMPLARY DAM­AGES ARISING OUT OF OR RELATED TO THE SALE OR USE OF THE PRODUCT SOLD HEREUNDER.

EXCLUSIVE REMEDY AND LIMITATION OF LIABILITY

. WHETHER IN AN ACTION BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE OR STRICT LIABILITY) OR ANY OTHER LEGAL THEORY, ANY LIABILITY OF VIKING SHALL

BE LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, OR AT VIKING'S OPTION, REFUND OF THE PURCHASE PRICE AS THE EXCLUSIVE REMEDY AND ANY LIABILITY OF VIKING SHALL BE SO LIMITED.

IT IS EXPRESSLY UNDERSTOOD AND AGREED THAT EACH AND EVERY PROVISION OF THIS AGREEMENT WHICH PROVIDES FOR DISCLAIMER OF WARRANTIES, EXCLUSION OF CONSEQUENTIAL DAMAGES, AND EXCLU­SIVE REMEDY AND LIMITATION OF LIABILITY, ARE SEVERABLE FROM ANY OTHER PROVISION AND EACH PROVISION IS A SEPARABLE AND INDEPENDENT ELEMENT OF RISK ALLOCATION AND IS INTENDED TO BE ENFORCED
AS SUCH.

Camera Specifications

Power: 5-9V DC regulated 150mA (6V DC adapter included)
Image Sensor: 1/4” color CMOS
Video Output: 1 VP-P composite, NTSC, 75 ohms
Resolution: 420 lines (640 x 480 @ 30fps / 307,200 pixels)
Sensitivity: 0.26 LUX (20 IRE) F 2.0
Lens: 3.4mm, pinhole 70° FOV (Field of View)
Tilt/Swivel Adjustment: Vertical +/- 20°, horizontal +/- 30° (see Diagram A)
Maximum Wire Run Length: 1000 ft with *RG59/RG6 for video and CAT5

for power (doubled pairs) and entry phone audio. 150 ft with CAT5E for video,
power and entry phone audio (longer video runs are possible by using video
balun transceivers, see Installation section F, page 5).

SSppeecciiffiiccaattiioonns

s

Entry Phone Specifications

Power: Telephone line powered 20V DC/20mA minimum
Dimensions: Overall: 140mm x 165mm x 66mm (5.5” x 6.5” x

2.6”) , Rough-in box: 114mm x 140mm x 64mm (4.5” x 5.5” x 2.5”)

Shipping Weight: 1.6 kg (3.5 lbs)
Speaker Volume: Approximately 70 db maximum @1m
Ring Voltage: 25V AC RMS minimum (for auto answer)
CPC Disconnect Time: 500ms minimum
REN #: 0.5 A

Entry Phone / Camera Specifications

Operating Temperature: -34° C to 65° C (-30° F to 150° F)
Humidity: Standard model: 5% to 95% non-condensing, EWP

model: Up to 100%
Connections: Standard model: (3) gel-filled butt connectors (3M
Scotchlok UR2) and 2-position terminal block, EWP model: (5) gel­filled butt connectors (3M Scotchlok UR2)

Recommended Surface Mount Box: Viking model VE-6x7 (Fax
Back Document 424)

2

* Note: RG59 or RG6 with solid center conductor and 95% bare copper braid shield.

Rotate
Left 30°

Diagram A

Camera Field of View:

70° Lens FOV

Rotate
Right 30°

Camera Lens

(1) .74”

diameter

Rear View of Optional

VE-6x7 (not included)

3.0” 3.3”

3.0”

Front View of Optional

VE-6x7 (not included)

2.25”

Condensation

Drain Hole

5.64”

6.72”

3.25”

(2) 0.2 x 0.43 slots

(4) 0.38” diameter

K-1705-3 shown with

VE-GNP Gooseneck

Pedestal (not included)

4.5”

2.5”

3/4” Conduit
Knockouts

Adhere gasket to front panel,
centering over mounting holes

5.5”

Condensation

Drain Hole

Rough-In Box*

(included)

1

2

ABC

3

DEF

4

GHI

5

JKL

6

MNO

7

PRS

8

TUV

9

W

XY

0

OPER

#

Call

VIKING

©

12

A

B

C

3

D

E

F

4

G

H

I

5

J

K

L

6

M

N

O

7

P

R

S

8

T

U

V

9

W

X

Y

0

O

P

E

R

#

Press "Call"button

then enter tenant code

Optional Instruction Label (included) - Clean

surface and adhere label when using a K-1705-3
with a K-1900-3 Apartment Entry Dialer.

(4) 6-32 X 3/4” Stainless steel, flat
head, hexdrive, screws (included)

IInnssttaallllaattiioon

n

The optional VE-6x7 Surface
Mount Box is designed to be sur­face mounted to a single gang
box, double gang box or VE-
GNP gooseneck pedestal (right).
For more information on the VE-

6x7 or the VE-GNP, retrieve Fax
Back Document 424.

A. Mounting

FFeeaattuurreessOOvveerrvviieew

w

3

* Note: Recommended
mounting height to bottom
of rough-in box is 50-54”.

Mounting Screws: 6-32 x 0.75" long
flathead with 5/64" hexdrive, 18-8 stainless
steel to prevent corrosion.

Faceplate: 14 guage 304 stainless steel.

Color Video Camera: Wide operating

temperature range of -30°F to 150°F, NTSC
composite video output with 420 lines of
resolution, 70° wide viewing angle lens, tilt and
swivel adjustments for aiming towards visitors.

Protective Camera Window: Impact resistant
polycarbonate lens with scratch resistant
coating and water-tight gasket.

Condensation Drain Hole

Faceplate Gasket: 1/8" thick closed cell PVC

to provide a water-tight seal.

VIKING

12

ABC3DEF

4

GHI5JKL6MNO

7

PRS8TUV9WXY

0

OPER

©

#

Call

Model:

Serial No:

XXXXXXXX

K-1705-3

Complies with FCC Part 15 and 68 Reg. No: AH3USA-32531-TE-E

P/N: DEV:

261102-1

REN: 1.0B

Viking Electronics, Inc. [phone]

VIKING

1531 Industrial St., Hudson, WI 54016

Keypad: Metal construction with internal seal

to provide vandal and weather resistance.

Microphone: Omni-directional microphone
with protective water-resistant cloth.

Speaker: Mylar speaker with rubber gasket to
maintain water-tight seal and eliminate water
deterioration.

Speaker Screen: Stainless steel speaker
screen with 0.018" diameter holes to prevent
punctures from paperclips, etc.

LED: Lights yellow for "In-Use" indication.

Push Button Switch: Push to initiate call,

push again to disconnect. Solid 304 stainless
steel internally sealed per IP67.

RoHS

Speaker Volume

Microphone Volume

DIP Switches (see page 6)

Earth Ground: To increase surge protection,

loosen the screw labeled (as shown) and
fasten a wire with spade terminal (included)
from the mounting screw to Earth Ground
(grounding rod, water pipe, etc.)

5.5

4

5

5.12

©

3000

V

G

H

12

E

PO

3.8

C

356

OOR

S

DOO

S

E

2

D

S

CH

1 2 3

R

S

8

1

E

2

O

N

I

CT

L

OCK

INPUT

or

or

o

or

G

©

MO

000

G

ELECTRONICS

H

6

APARTMENT OR OFFICE

R

M

E

POWER

13.8 VAC

DOOR S

S

S

G

©

000

V

G

E

S

016

A

ENTRY PHONE CONTROLLER

5

6

7

8910

3141516

81920

25

26272829

30

C

G

D

O

S

1

O

2

S

O

3

S

3

S

4

/

AUX

INPUT

T

E

Rear View of the K-1705-3

Optional K-1900-3 Apartment

Entry Dialer (not included)

Fax Back Number 312

Optional C-2000A Advanced Door

Entry Controller (not included)

Fax Back Number 156

Optional C-3000 Apartment
Entry System (not included)

Fax Back Number 162

*** Note: To increase surge protection, loosen the PCB mount­ing screw labeled (as shown right) and fasten a wire with
spade terminal (included) from the mounting screw to Earth
Ground (grounding rod, water pipe, etc.)

** Note: The gel-filled (water-tight)
butt connectors are designed for insu­lation displacement on 19-26 gauge
wire with a maximum insulation of

0.082 inches. Cut off the stripped wire
ends prior to terminating.

* Note: When installing a line powered phone on a low voltage and/or low
loop current phone system extension, a TBB-1 Talk Battery Booster may
be required.

?

Need More Information on the TBB-1?

Call [phone] and select 630.

Optional C-4000 Apartment/

Office Entry Controller (not

included) Fax Back Number 164

B. Wiring the K-1705-3 Phone Board

C. Wiring the K-1705-3 Camera

1. Using RG59 for Video and CAT5 for Camera Power and Phone Board Audio (Recommended)

IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC outlet
and the telephone line. It is recommended that a surge protector be installed to protect against such surges. Contact
Panamax at [phone] or Electronic Specialists Inc. at [phone].

!

4

** Gel-Filled

Butt Connectors

UNIT APARTMENT

NTRY CONTROLLER MODULE

D

POSTA

TRIKE

TRIK

L

1

IP

ENTRY

NTRY

(included)

MODEL C-

IKIN

ELECTRONICS

UDSON, WI 54016

R

MULTI-MODULE

NTERCONNE

UT I

Green (Tip)

12 APARTMENT LINE

* C.O. Line

or Analog

PABX/KSU

Station

VIKIN

PWR 13.8 VA

N

ARTH

HONE LIN

INE OUT

1 2 3 4

DVANCED DOOR/GATE AND

NE 1

TRIKE

R

NTRY PH

TO PHONES

11121

NE

NTRY PH

IKIN

LECTRONIC

HUDSON, WI 54

TRIKE 2

R

MODEL C-2

NE

NTRY PH

171

A

TRIKE

TRIKE

R

R

.

OORBELL SWITCH

NTRY PHONE 4

AUX. CONTACT

OUTPU

21222324

VIKING

WER

1

VA

WIT

Red (Ring)

J21X

IN/OUT

VIKIN

PROGRA

PHON

LED1

C

PROGRAM
PHONE

N.O. COM N.C.
DOOR STRIKE 1

C.O. LINE
INPUT

LINE

6.

Model:

Serial No:

K-1705-3

Complies with FCC Part 15 and 68 Reg. No: AH3USA-32531-TE-E

P/N: DEV:

261102-1

REN: 1.0B

Viking Electronics, Inc. [phone]

VIKING

1531 Industrial St., Hudson, WI 54016

DEL C-4

WIEGAND INPUT

BLK RED GRN WHT

ENTRY 2

BLK RED GRN WHT

ENTRY 3

LOG BUS

BLK RED GRN WHT

ENTRY 4

RS-232 PORT

ENTRY CONTROLLE

TRIKE RELAY

N.O. COM N.C.

N.O. COM N.C.

DOOR STRIKE 2

DOOR STRIKE 3

AUX

ENTRY

ENTRY

PHONE 1

PHONE 2

UDSON,5401

N.O. COM N.C.
DOOR STRIKE 4

ENTRY
PHONE 3

ENTRY
PHONE 4

VIKIN

BLK RED GRN WHT

ENTRY 1

REX1REX2REX3REX4H L

XXXXXXXX

RoHS

4.0

Spade
Terminal
(included)

*** Earth

Ground

(optional)

APARTMEN

T ENTRY

SYSTE

M

VIKING

ELECTRONICS

HUDSON, WI 54016

VIKING©

MOD

EL K-

1900-3

RELAY CONTAC

TS

AU

X.

18

V

DC

1A 1B

R

IG.

T

200

m

POWE

R13.8 VAC

LINE IN PHONE

PROGRAMMING

OFF O

1 2 3 4 5 6 7 8 9 10

N

A

NPU

T

I

-

+

r

Back View of the K-1705-3

Model:

K-1705-3

Complies with FCC Part 15 and 68 Reg. No: AH3USA-32531-TE-E

P/N: DEV:

261102-1

REN: 1.0B

Viking Electronics, Inc. [phone]

VIKING

1531 Industrial St., Hudson, WI 54016

Green

Red

Serial No:

XXXXXXXX

RoHS

3-Wire Gel-Filled Butt Connectors

included (3M Scotchlok UR2)

Center conductor

Yellow (Video)

- Black (GND)

+ Red (6VDC)

Phone Board Audio In/Out (Tip) W/BL

Phone Board Audio In/Out (Ring) BL/W

stripped back 5/8"

Twisted foil and
braided shield

** Camera GND (-) W/O

** Camera Pwr (+) O/W

*** RG59 or RG6

Shielded

Video Cable

Up to 1000 ft

CAT5 Cable

** Up to 500 ft

"F"

Connector

BL/W W/BL

"F" to Phono Plug

Adapter

Shack part #278-252)

W/O

O/W

(Radio

Camera GND (-)

Camera Power (+)

See page 4, section B

Wiring Phone Board

To unused input on TV,
VHF modulator, whole
house video distribution
equipment, etc.

6V DC Adapter

(included)

Black

(-)

Crimp-on Splice

Connectors (not included)

120V AC

(+)

Black with
White Stripe

!

* Note: Up to 150 ft video cable run length can be achieved using CAT5E or CAT6 cable. Longer cable runs can be used if a passive or active video Balun transceiver is used on
each end of the cable. Generally, passive transceivers can achieve up to 750 ft cable runs where active transceivers can achieve up to 3000 ft runs depending on cable type, etc.
The type of video balun transceiver required is specific to your cable run length. For more information on video balun transceivers go to: www.northernvideo.com.

Caution: When routing CAT5E or CAT6 cable, maintain a minimum distance of 3 ft from any parallel high voltage wire (110 VAC) and a minimum of 2 ft from crossing any high volt­age wire. For installations where RF noise is expected (commercial applications) or wire runs are near high voltage (110 VAC) wires, a shielded video cable such as RG6 is recom­mended.

D. Adjusting the Camera

The camera can be tilted and rotated to your desired
position. A portable service (test) monitor can be used to
determine the correct viewing angle during installation.

Important: To prevent the edge of the faceplate from
being viewed in the video image, do not rotate the cam­era beyond 30 degrees or tilt beyond 20 degrees.

** Note: The maximum camera power supply wire run length is 500 ft of 24 gauge wire (CAT 5/6), longer runs are possible by doubling pairs or increasing the wire gauge.

2. Using CAT5E or CAT6 for Video, Camera Power and Phone Board Audio (see Caution below)

*** Note: RG59 or RG6 with solid center conductor and 95% bare copper braid shield.

PPrrooggrraammmmiinng

g

A. Dip Switch Programming

Rear View of the K-1705-3

5

Switch 1

OFF

ON

OFF

ON

Switch 2

OFF

OFF

ON

ON

Maximum Call Time

Disabled (default)

1 minute

3 minutes

9 minutes

Switch 3

OFF

ON

Disconnect on Dial Tone

Off

On (default)

Switch 7

OFF

ON

Auto Answer Feature

Automatic answer disabled

Automatic answer enabled (default)

Switch 8

OFF

ON

Push Button Feature

Connects calls only

Connects/disconnects calls (default)

Switch 4

OFF

ON

VOX Switching Speed

Fast, 0.2 seconds (default)

Slow, 0.7 seconds

Switch 5

ON

OFF

Switch 6

ON

OFF

Audio Detection

Normal audio detection

Increase audio detect sensitivity for
low level lines. Useful in applications
in which voice or busy signals have
trouble breaking over the speaker.

Back View of the K-1705-3

Model:

Serial No:

XXXXXXXX

K-1705-3

Complies with FCC Part 15 and 68 Reg. No: AH3USA-32531-TE-E

P/N: DEV:

261102-1

REN: 1.0B

VIKING

Green

Red

Viking Electronics, Inc. [phone]

1531 Industrial St., Hudson, WI 54016

RoHS

3-Wire Gel-Filled Butt

Connectors included

(3M Scotchlok UR2)

Yellow (Video)

- Black (GND)

+ Red (6VDC)

Phone Board Audio In/Out (Tip) W/BL

Phone Board Audio In/Out (Ring) BL/W

Video Out (+) W/G

Video GND (-) G/W

** Camera GND (-) W/O

** Camera Pwr (+) O/W

CAT5E or

CAT6 Cable

(see Caution below)

* Up to 150 ft

W/G G/W

W/O

O/W

BL/W W/BL

Video Out (+)

Video GND (-)

Camera GND (-)

Camera Power (+)

See page 4, section E

Wiring Phone Board

To unused input on TV, VHF

modulator, whole house video

distribution equipment, etc.

Phono (RCA) Plug,

F Connector, Etc.

6V DC Adapter

(included)

Black

(-)

(+)

Black with
White Stripe

(4) Crimp-on Splice

Connectors (not included)

(-)

(+)

!

120V AC

Vertical (Tilt)

Adjustment

+/- 20 degrees

maximum

Horizontal (Rotation)

Adjustment

+/- 30 degrees maximum

VIKING

©

Model:

Serial No:

XXXXXXXX

K-1705-3

Complies with FCC Part 15 and 68 Reg. No: AH3USA-32531-TE-E

P/N: DEV:

261102-1

VIKING

REN: 1.0B

Viking Electronics, Inc. [phone]

1531 Industrial St., Hudson, WI 54016

RoHS

12

ABC3DEF

4

GHI5JKL6MNO

7

PRS8TUV9WXY

0

#

OPER

DIP Switches (shown

in default positions)

Call

8
7
6
5

4
3
2
1

ON OFF

B. Volume Adjustments

C. Auto-Answer Feature

(DIP Switch 7)

With DIP switch 7 in the “ON” position (default), the K-1705-3 will automatically answer the line during the first incom­ing ring. This feature is useful for monitoring entrances. In the “OFF” position, the K-1705-3 will not automatically
answer incoming calls.

Certain noisy locations (background traffic,
machinery or wind) may cause one way talk path
(only microphone audio is heard). In this case,
the microphone volume may need to be
decreased as shown.

D. Push Button Hang Up (DIP Switch 8)

With DIP switch 8 in the “ON” position (default), the “Call” button alternately connects and disconnects calls. In the
“OFF” position, the “Call” button is only used to connect and the K-1705-3 must rely on call progress (busy, return to
dial tone, silence time-out, or maximum call time) for an automatic disconnect.

With DIP switch 4 in the “OFF” position (default), the VOX switching speed (delay time between talk and listen mode)
is set to fast (0.2 seconds). In the “ON” position, it is set to slow (0.7 seconds).

E. VOX (Talk/Listen) Switching Speed (DIP Switch 4)

The K-1705-3 will output 3 beeps and automatically hang-up after detecting any of the following: busy signal (standard
or fast/reorder), CPC (short break in line current when called party hangs up), return to dial tone, maximum call time
or silence time out.

F. Advanced Call Progress Detection

1. Microphone

To increase, decrease or turn off the speaker (for
monitoring purposes only), adjust the speaker
volume control as shown.

2. Speaker

OOppeerraattiioon

n

When the push button is pressed, the K-1705-3 phone goes off-hook, much like a standard speaker phone. The keypad
may then be used to dial any number. In the event that the line is busy, the K-1705-3 will hang-up. The K-1705-3 will also
automatically hang up on CPC, silence, busy signal, return to dial tone or time out. If programmed to auto-answer (DIP
switch 7 ON), the K-1705-3 will also answer any incoming call.

The K-1705-3 color video camera operates completely independently of the K-1705-3 phone board. With power supplied
to the camera, it will continuously output a video signal.

6

Microphone Volume Speaker Volume

OffOff

Model:

Serial No:

XXXXXXXX

K-1705-3

Complies with FCC Part 15 and 68 Reg. No: AH3USA-32531-TE-E

P/N: DEV:

261102-1

VIKING

REN: 1.0B

Viking Electronics, Inc. [phone]

1531 Industrial St., Hudson, WI 54016

RoHS

The K-1900-3 converts any Touch Tone phone into a multi-number auto dialer that will store up to 150 telephone numbers in non­volatile memory. Use with Viking’s K-1705-3 or K-1900-8 phones to provide vandal resistant handsfree or handset communication.
When a call initiated by the K-1900-3 is answered by an apartment or business tenant, a built-in contact closure may be activated
to control an electric gate or door strike. Up to 150 keyless entry codes may also be programmed, providing tenants with keyless
entry. The K-1900-3 can be programmed locally or remotely using a standard Touch Tone phone. The K-1900-3 has built-in user
dialing restriction to help prevent unauthorized calls and toll fraud.

A. K-1900-3 Apartment/Office Entry Dialer

AApppplliiccaattiioonns

s

The C-2000A allows up to 4 entry phones to call into your existing residential or business phones or phone system. Tenants may
answer the call, converse with the visitor and activate a contact closure to control electronic gates or door strikes. The C-2000A
provides “Caller ID,” “Call Waiting ID” and “Call Waiting” tone when the phone line is in use. Tenants may gain entry at each gate
by entering a Touch Tone keyless entry code. Tenants may call out to each entry phone for monitoring purposes. An auxiliary input
is also available for connecting a common garage door opener/receiver and auxiliary keyless entry keypads.

B. C-2000A Advanced Door/Gate and Entry Phone Controller

(Example

)

7

APARTMENT ENTRY

VIKING

MODEL K-1900-3

POWER 13.8 VAC

PROGRAMMING

LINE IN PHONE

OFF ON

SYSTEM

VIKING

ELECTRONICS

HUDSON, WI 54016

©

RELAY CONTACTS

1A 1B

12345678910

1 2 3 4 5 6 7 8 9 10

TRIG.

INPUT

AUX.

18 VDC

200mA

- +

18VDC/200mA (maximum) Power Output:

+

-

for powering door strikes, magnetic locks, etc.

13.8V AC
Adapter

Provided

* C.O. Line

or Analog

PABX/KSU

Station

120V AC

Auxiliary Relay Trigger Input:

momentary contact closure from postal lock, etc.

COM

Secondary Relay Contacts: to trigger

N.C

timed lights, camera control, etc.

N.O.

K-1705-3

Local Programming/

Security Code

Bypass Switch

Relay Contact Specifications:

5A@30VDC/250VAC maximum

Doorstrike/Magnetic Lock

Normally Closed Relay Contact

Normally Open Relay Contact

Note: Power typically not

or

required for gate controllers.

Example:

Amplified

RF Splitter

1 2 3 4

Multi Room

Video Out

Example:

2-4 Channel Video

RF Modulator

02

Antenna,

CATV, etc.

Programming section C (page 4)

To Standard

Analog Touch

Tone House

Phone(s)

Entry Phone 1

E-50-SS shown,

not included

(Example: Front Door)

120V AC

13.8V AC
Adapter

(included)

See DIP Switch Programming

C.O. / Phone

Line Input

Video Out

Entry Phone 2, E-50-SS

shown, not included

Video Out

: Back Door

Ground

(optional)

* Earth

Tip (Audio)

Ring

VIKING

PWR 13.8 VAC

EARTH GND

PHONE LINE

INPUT

LINE OUT

1 2 3 4 5678 9 10 11 1213 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

Tip (Audio)

Ring

©

HUDSON, WI 54016

ADVANCED DOOR/GATE AND
ENTRY PHONE CONTROLLER

ENTRY PHONE 1

DOOR STRIKE 1

TO PHONES

ENTRY PHONE 2

MODEL C-2000A

VIKING

ELECTRONICS

DOOR STRIKE 2

ENTRY PHONE 3

DOOR STRIKE 3

ENTRY PHONE 4

DOOR STRIKE 4

DOORBELL SWITCH /

AUX. INPUT

To Gate
Controller

To Entry Phone 4

A contact closure output is available for each

entry phone. An auxiliary output is also available.

Entry Phone 3, E-30 in VE-5x5 shown, not included
(Example: Garage)

AUX. CONTACT

OUTPUT

(Power typically not

required for gate controllers)

Optional Doorbell Switch
(not included, see Programming
section L on page 5)

or

Entry Phone 4, K-1705-3 in VE-6x7 shown,
not included (Example: Gate)

5A@30VDC/
250VAC
maximum

Optional Postal Lock
(not included)

Doorstrike/

Magnetic Lock

Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.

Fax Back Doc 159

ZF302520 Rev A

Printed in the U.S.A.

PPrroodduuccttSSuuppppoorrttLLiinnee......771155..338866..8866666

6

FFaaxxBBaacckkLLiinnee......771155..338866..4433445

5

C. Provide 4 Door Entry Points with Keyless Entry (or Optional Card Readers) for up to 250

Apartments or Offices

The C-4000 converts any four Touch Tone phones into multi-number auto dialers that will store up to 250 telephone numbers in
non-volatile memory. Use with Viking’s K-1705-3 phone to provide vandal resistant handsfree or handset communication from entry
points to apartments or offices. When a call initiated by the C-4000 is answered by an apartment or business tenant, a built-in con­tact closure may be activated to control an electric gate or door strike. Up to 250 entry codes may also be programmed providing
tenants with keyless entry or optional HID-1 Card Readers may be added for Proxy card entry. The C-4000 can be programmed
locally or remotely using a standard Touch Tone phone. The C-4000 has built-in user dialing restriction to help prevent unauthorized
calls and toll fraud.

?

Need More Information on Directories?

Call [phone] and select 158.

?

Need More Information on VE Backboxes?

Call [phone] and select 424.

?

Need More Information on the HID-2?

Call [phone] and select 199.

?

Need More Information on the HID-1?

Call [phone] and select 197.

IMPORTANT: Electronic devices are susceptible to lightning and power station
electrical surges from both the AC outlet and the telephone line. It is recommend­ed that a surge protector be installed to protect against such surges. Contact
Panamax at [phone] or Electronic Specialists Inc. at [phone].

!

* Note: Maximum Wiegand run length is 2000 feet using 24 gauge wire when using the Viking Model HID-1 proxy card reader, and 4000 feet for the HID­2 keypad. Run length is reduced to half if two share the same wire run from the same C-4000 entry point. Run length will also be reduced if using a

Wiegand device other than the Viking Model HID-1, that requires more than 35mA average operating current. Run lengths can be doubled by doubling up
on the BLACK and RED 24 gauge wire, or using 21 gauge (or larger) wire. Certain electrically noisy locations might require shielded wire.

8

Viking D-Series Directory

(not included)

13.8V AC
Adapter

Included

120V AC

VIKING

POWER

13.8 VAC

©

APARTMENT OR OFFICE

ENTRY CONTROLLER

MODEL C-4000

VIKING

ELECTRONICS

HUDSON, WI 54016

Power Supply

5A@30VDC/250VAC

maximum

(not included)

Power typically not required
for gate controllers.

Doorstrike/Magnetic Lock (not included)

A contact closure output is available

C.O. Line or Analog

PABX/KSU Station

Local

Programming

Phone

for each entry phone.

Optional C-3000 (not included)

MODEL C-3000

VIKING

POWER

13.8 VAC

POSTAL

LOCK
INPUT

DIP

SWITCH

1 2 3

©

VIKING

ELECTRONICS

HUDSON, WI 54016

12 UNIT APARTMENT

ENTRY CONTROLLER MODULE

DOOR

DOOR

STRIKE

STRIKE

2

1

12 APARTMENT LINES IN/OUT

8

3456712

MULTI-MODULE

INTERCONNECT

ENTRY 1 ENTRY 2

OUT IN

RJ21X

PROGRAM

PHONE

LED1

C

PROGRAM
PHONE

DOOR STRIKE RELAYS

N.O. COM N.C.

N.O. COM N.C.

DOOR STRIKE 1

DOOR STRIKE 2

C.O. LINE

AUX

ENTRY

INPUT

LINE

PHONE 1

N.O. COM N.C.
DOOR STRIKE 3

ENTRY

PHONE 2

ENTRY

PHONE 3

N.O. COM N.C.
DOOR STRIKE 4

ENTRY

PHONE 4

WIEGAND INPUTS

BLK RED GRN WHT

BLK RED GRN WHT

ENTRY 1

REX1REX2REX3REX4H L

BLK RED GRN WHT

ENTRY 2

LOG BUS

* 609m (2000 ft) max

Proximity Card Reader

K-1705-3

ENTRY 3

RS-232 PORT

BLK RED GRN WHT

ENTRY 4

Entry Points 2-4 should
be wired identical to Entry
Point 1 as shown.

Viking HID-2 Keypad

(not included)

* 1219m (4000 ft) max

Viking HID-1

(not included)

Optional "Push to Open / Request to Exit"

Button (not included)

Analog Entry Phone

The K-1705-3 is shown with
optional VE-6x7 backbox.

- or -

If some tenants do not have C.O. phone service, the
Viking model C-3000 can be added to ring up to 12
tenant's phones. Up to eight C-3000 units can be
cascaded to support a total of 96 "No C.O." tenants.